diff options
Diffstat (limited to 'drivers/pinctrl/pinctrl-abx500.c')
| -rw-r--r-- | drivers/pinctrl/pinctrl-abx500.c | 187 |
1 files changed, 102 insertions, 85 deletions
diff --git a/drivers/pinctrl/pinctrl-abx500.c b/drivers/pinctrl/pinctrl-abx500.c index 1d3f988c2c8b..8f25df06bc6b 100644 --- a/drivers/pinctrl/pinctrl-abx500.c +++ b/drivers/pinctrl/pinctrl-abx500.c @@ -1041,98 +1041,115 @@ static int abx500_pin_config_get(struct pinctrl_dev *pctldev, static int abx500_pin_config_set(struct pinctrl_dev *pctldev, unsigned pin, - unsigned long config) + unsigned long *configs, + unsigned num_configs) { struct abx500_pinctrl *pct = pinctrl_dev_get_drvdata(pctldev); struct gpio_chip *chip = &pct->chip; unsigned offset; int ret = -EINVAL; - enum pin_config_param param = pinconf_to_config_param(config); - enum pin_config_param argument = pinconf_to_config_argument(config); - - dev_dbg(chip->dev, "pin %d [%#lx]: %s %s\n", - pin, config, (param == PIN_CONFIG_OUTPUT) ? "output " : "input", - (param == PIN_CONFIG_OUTPUT) ? (argument ? "high" : "low") : - (argument ? "pull up" : "pull down")); - - /* on ABx500, there is no GPIO0, so adjust the offset */ - offset = pin - 1; - - switch (param) { - case PIN_CONFIG_BIAS_DISABLE: - ret = abx500_gpio_direction_input(chip, offset); - if (ret < 0) - goto out; - /* - * Some chips only support pull down, while some actually - * support both pull up and pull down. Such chips have - * a "pullud" range specified for the pins that support - * both features. If the pin is not within that range, we - * fall back to the old bit set that only support pull down. - */ - if (abx500_pullud_supported(chip, pin)) - ret = abx500_set_pull_updown(pct, - pin, - ABX500_GPIO_PULL_NONE); - else - /* Chip only supports pull down */ - ret = abx500_gpio_set_bits(chip, AB8500_GPIO_PUD1_REG, - offset, ABX500_GPIO_PULL_NONE); - break; - - case PIN_CONFIG_BIAS_PULL_DOWN: - ret = abx500_gpio_direction_input(chip, offset); - if (ret < 0) - goto out; - /* - * if argument = 1 set the pull down - * else clear the pull down - * Some chips only support pull down, while some actually - * support both pull up and pull down. Such chips have - * a "pullud" range specified for the pins that support - * both features. If the pin is not within that range, we - * fall back to the old bit set that only support pull down. - */ - if (abx500_pullud_supported(chip, pin)) - ret = abx500_set_pull_updown(pct, - pin, - argument ? ABX500_GPIO_PULL_DOWN : ABX500_GPIO_PULL_NONE); - else - /* Chip only supports pull down */ - ret = abx500_gpio_set_bits(chip, AB8500_GPIO_PUD1_REG, - offset, - argument ? ABX500_GPIO_PULL_DOWN : ABX500_GPIO_PULL_NONE); - break; - - case PIN_CONFIG_BIAS_PULL_UP: - ret = abx500_gpio_direction_input(chip, offset); - if (ret < 0) - goto out; - /* - * if argument = 1 set the pull up - * else clear the pull up - */ - ret = abx500_gpio_direction_input(chip, offset); - /* - * Some chips only support pull down, while some actually - * support both pull up and pull down. Such chips have - * a "pullud" range specified for the pins that support - * both features. If the pin is not within that range, do - * nothing - */ - if (abx500_pullud_supported(chip, pin)) - ret = abx500_set_pull_updown(pct, - pin, - argument ? ABX500_GPIO_PULL_UP : ABX500_GPIO_PULL_NONE); - break; + int i; + enum pin_config_param param; + enum pin_config_param argument; + + for (i = 0; i < num_configs; i++) { + param = pinconf_to_config_param(configs[i]); + argument = pinconf_to_config_argument(configs[i]); + + dev_dbg(chip->dev, "pin %d [%#lx]: %s %s\n", + pin, configs[i], + (param == PIN_CONFIG_OUTPUT) ? "output " : "input", + (param == PIN_CONFIG_OUTPUT) ? + (argument ? "high" : "low") : + (argument ? "pull up" : "pull down")); + + /* on ABx500, there is no GPIO0, so adjust the offset */ + offset = pin - 1; + + switch (param) { + case PIN_CONFIG_BIAS_DISABLE: + ret = abx500_gpio_direction_input(chip, offset); + if (ret < 0) + goto out; + /* + * Some chips only support pull down, while some + * actually support both pull up and pull down. Such + * chips have a "pullud" range specified for the pins + * that support both features. If the pin is not + * within that range, we fall back to the old bit set + * that only support pull down. + */ + if (abx500_pullud_supported(chip, pin)) + ret = abx500_set_pull_updown(pct, + pin, + ABX500_GPIO_PULL_NONE); + else + /* Chip only supports pull down */ + ret = abx500_gpio_set_bits(chip, + AB8500_GPIO_PUD1_REG, offset, + ABX500_GPIO_PULL_NONE); + break; - case PIN_CONFIG_OUTPUT: - ret = abx500_gpio_direction_output(chip, offset, argument); - break; + case PIN_CONFIG_BIAS_PULL_DOWN: + ret = abx500_gpio_direction_input(chip, offset); + if (ret < 0) + goto out; + /* + * if argument = 1 set the pull down + * else clear the pull down + * Some chips only support pull down, while some + * actually support both pull up and pull down. Such + * chips have a "pullud" range specified for the pins + * that support both features. If the pin is not + * within that range, we fall back to the old bit set + * that only support pull down. + */ + if (abx500_pullud_supported(chip, pin)) + ret = abx500_set_pull_updown(pct, + pin, + argument ? ABX500_GPIO_PULL_DOWN : + ABX500_GPIO_PULL_NONE); + else + /* Chip only supports pull down */ + ret = abx500_gpio_set_bits(chip, + AB8500_GPIO_PUD1_REG, + offset, + argument ? ABX500_GPIO_PULL_DOWN : + ABX500_GPIO_PULL_NONE); + break; - default: - dev_err(chip->dev, "illegal configuration requested\n"); - } + case PIN_CONFIG_BIAS_PULL_UP: + ret = abx500_gpio_direction_input(chip, offset); + if (ret < 0) + goto out; + /* + * if argument = 1 set the pull up + * else clear the pull up + */ + ret = abx500_gpio_direction_input(chip, offset); + /* + * Some chips only support pull down, while some + * actually support both pull up and pull down. Such + * chips have a "pullud" range specified for the pins + * that support both features. If the pin is not + * within that range, do nothing + */ + if (abx500_pullud_supported(chip, pin)) + ret = abx500_set_pull_updown(pct, + pin, + argument ? ABX500_GPIO_PULL_UP : + ABX500_GPIO_PULL_NONE); + break; + + case PIN_CONFIG_OUTPUT: + ret = abx500_gpio_direction_output(chip, offset, + argument); + break; + + default: + dev_err(chip->dev, "illegal configuration requested\n"); + } + } /* for each config */ out: if (ret < 0) dev_err(pct->dev, "%s failed (%d)\n", __func__, ret); |