blob: 687f8ff1ef983dce0bfae0ca432ede630003c11f (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
|
/*
* Configuation settings for the Hitachi Solution Engine 7722
*
* Copyright (C) 2007 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __MS7722SE_H
#define __MS7722SE_H
#define CONFIG_CPU_SH7722 1
#define CONFIG_DISPLAY_BOARDINFO
#undef CONFIG_SHOW_BOOT_PROGRESS
/* SMC9111 */
#define CONFIG_SMC91111
#define CONFIG_SMC91111_BASE (0xB8000000)
/* MEMORY */
#define MS7722SE_SDRAM_BASE (0x8C000000)
#define MS7722SE_FLASH_BASE_1 (0xA0000000)
#define MS7722SE_FLASH_BANK_SIZE (8*1024 * 1024)
#define CONFIG_SYS_PBSIZE 256 /* Buffer size for Console output */
#define CONFIG_SYS_BAUDRATE_TABLE { 115200 } /* List of legal baudrate settings for this board */
/* SCIF */
#define CONFIG_CONS_SCIF0 1
#define CONFIG_SYS_MEMTEST_START (MS7722SE_SDRAM_BASE)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (60 * 1024 * 1024))
#undef CONFIG_SYS_MEMTEST_SCRATCH /* Scratch address used by the alternate memory test */
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* Enable temporary baudrate change while serial download */
#define CONFIG_SYS_SDRAM_BASE (MS7722SE_SDRAM_BASE)
#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* maybe more, but if so u-boot doesn't know about it... */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 4 * 1024 * 1024) /* default load address for scripts ?!? */
#define CONFIG_SYS_MONITOR_BASE (MS7722SE_FLASH_BASE_1) /* Address of u-boot image
in Flash (NOT run time address in SDRAM) ?!? */
#define CONFIG_SYS_MONITOR_LEN (128 * 1024) /* */
#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Size of DRAM reserved for malloc() use */
#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024)
/* FLASH */
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#undef CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_BASE (MS7722SE_FLASH_BASE_1) /* Physical start address of Flash memory */
#define CONFIG_SYS_MAX_FLASH_SECT 150 /* Max number of sectors on each
Flash chip */
/* if you use all NOR Flash , you change dip-switch. Please see MS7722SE01 Manual. */
#define CONFIG_SYS_MAX_FLASH_BANKS 2
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE + (0 * MS7722SE_FLASH_BANK_SIZE), \
CONFIG_SYS_FLASH_BASE + (1 * MS7722SE_FLASH_BANK_SIZE), \
}
#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) /* Timeout for Flash erase operations (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) /* Timeout for Flash write operations (in ms) */
#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) /* Timeout for Flash set sector lock bit operations (in ms) */
#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) /* Timeout for Flash clear lock bit operations (in ms) */
#undef CONFIG_SYS_FLASH_PROTECTION /* Use hardware flash sectors protection instead of U-Boot software protection */
#undef CONFIG_SYS_DIRECT_FLASH_TFTP
#define CONFIG_ENV_OVERWRITE 1
#define CONFIG_ENV_SECT_SIZE (8 * 1024)
#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + (1 * CONFIG_ENV_SECT_SIZE))
#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) /* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + (2 * CONFIG_ENV_SECT_SIZE))
/* Board Clock */
#define CONFIG_SYS_CLK_FREQ 33333333
#define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ
#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_TMU_CLK_DIV (4) /* 4 (default), 16, 64, 256 or 1024 */
#endif /* __MS7722SE_H */
|
