1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
|
.. SPDX-License-Identifier: GPL-2.0+
LS1046ARDB
==========
The LS1046A Reference Design Board (RDB) is a high-performance computing,
evaluation, and development platform that supports the QorIQ LS1046A
LayerScape Architecture processor. The LS1046ARDB provides SW development
platform for the Freescale LS1046A processor series, with a complete
debugging environment. The LS1046A RDB is lead-free and RoHS-compliant.
LS1046A SoC Overview
--------------------
Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS1046A
SoC overview.
LS1046ARDB board Overview
-------------------------
- SERDES1 Connections, 4 lanes supporting:
- Lane0: 10GBase-R with x1 RJ45 connector
- Lane1: 10GBase-R Cage
- Lane2: SGMII.5
- Lane3: SGMII.6
- SERDES2 Connections, 4 lanes supporting:
- Lane0: PCIe1 with miniPCIe slot
- Lane1: PCIe2 with PCIe x2 slot
- Lane2: PCIe3 with PCIe x4 slot
- Lane3: SATA
- DDR Controller
- 8GB 64bits DDR4 SDRAM. Support rates of up to 2133MT/s
- IFC/Local Bus
- One 512 MB NAND flash with ECC support
- CPLD connection
- USB 3.0
- one Type A port, one Micro-AB port
- SDHC: connects directly to a full SD/MMC slot
- DSPI: 64 MB high-speed flash Memory for boot code and storage (up to 108MHz)
- 4 I2C controllers
- UART
- Two 4-pin serial ports at up to 115.2 Kbit/s
- Two DB9 D-Type connectors supporting one Serial port each
- ARM JTAG support
Memory map from core's view
----------------------------
================== ================== ================ =====
Start Address End Address Description Size
================== ================== ================ =====
``0x00_0000_0000`` ``0x00_000F_FFFF`` Secure Boot ROM 1M
``0x00_0100_0000`` ``0x00_0FFF_FFFF`` CCSRBAR 240M
``0x00_1000_0000`` ``0x00_1000_FFFF`` OCRAM0 64K
``0x00_1001_0000`` ``0x00_1001_FFFF`` OCRAM1 64K
``0x00_2000_0000`` ``0x00_20FF_FFFF`` DCSR 16M
``0x00_7E80_0000`` ``0x00_7E80_FFFF`` IFC - NAND Flash 64K
``0x00_7FB0_0000`` ``0x00_7FB0_0FFF`` IFC - CPLD 4K
``0x00_8000_0000`` ``0x00_FFFF_FFFF`` DRAM1 2G
``0x05_0000_0000`` ``0x05_07FF_FFFF`` QMAN S/W Portal 128M
``0x05_0800_0000`` ``0x05_0FFF_FFFF`` BMAN S/W Portal 128M
``0x08_8000_0000`` ``0x09_FFFF_FFFF`` DRAM2 6G
``0x40_0000_0000`` ``0x47_FFFF_FFFF`` PCI Express1 32G
``0x48_0000_0000`` ``0x4F_FFFF_FFFF`` PCI Express2 32G
``0x50_0000_0000`` ``0x57_FFFF_FFFF`` PCI Express3 32G
================== ================== ================ =====
QSPI flash map
--------------
================== ================== ================== =====
Start Address End Address Description Size
================== ================== ================== =====
``0x00_4000_0000`` ``0x00_400F_FFFF`` RCW + PBI 1M
``0x00_4010_0000`` ``0x00_402F_FFFF`` U-Boot 2M
``0x00_4030_0000`` ``0x00_403F_FFFF`` U-Boot Env 1M
``0x00_4040_0000`` ``0x00_405F_FFFF`` PPA 2M
``0x00_4060_0000`` ``0x00_408F_FFFF`` Secure boot header 3M
+ bootscript
``0x00_4090_0000`` ``0x00_4093_FFFF`` FMan ucode 256K
``0x00_4094_0000`` ``0x00_4097_FFFF`` QE/uQE firmware 256K
``0x00_4098_0000`` ``0x00_40FF_FFFF`` Reserved 6M
``0x00_4100_0000`` ``0x00_43FF_FFFF`` FIT Image 48M
================== ================== ================== =====
Booting Options
---------------
NB: The reference manual documents the RCW source with the *least-significant
bit first*.
QSPI boot
^^^^^^^^^
This is the default. ``{ SW5[0:8], SW4[0] }`` should be ``0010_0010_0``.
SD boot and eMMC boot
^^^^^^^^^^^^^^^^^^^^^
``{ SW5[0:8], SW4[0] }`` should be ``0010_0000_0``. eMMC is selected only if
there is no SD card in the slot.
.. _ls1046ardb_jtag:
JTAG boot
^^^^^^^^^
To recover a bricked board, or to perform initial programming, the ls1046
supports using two hard-coded Reset Configuration Words (RCWs). Unfortunately,
this configuration disables most functionality, including the uarts and ethernet.
However, the SD/MMC and flash controllers are still functional. To get around
the lack of a serial console, we will use ARM semihosting instead. When
enabled, OpenOCD will interpret certain instructions as calls to the host
operating system. This allows U-Boot to use the console, read/write files, or
run arbitrary commands (!).
When configuring U-Boot, ensure that ``CONFIG_SEMIHOSTING``,
``CONFIG_SPL_SEMIHOSTING``, and ``CONFIG_SEMIHOSTING_SERIAL`` are enabled.
``{ SW5[0:8], SW4[0] }`` should be ``0100_1111_0``. Additionally, ``SW4[7]``
should be set to ``0``. Connect to the "console" USB connector on the front of
the enclosure.
Create a new file called ``u-boot.tcl`` (or whatever you choose) with the
following contents::
# Load the configuration for the LS1046ARDB
source [find board/nxp_rdb-ls1046a.cfg]
# Initialize the scan chain
init
# Stop the processor
halt
# Enable semihosting
arm semihosting enable
# Load U-Boot SPL
load_image spl/u-boot-spl 0 elf
# Start executing SPL at the beginning of OCRAM
resume 0x10000000
Then, launch openocd like::
openocd -f u-boot.tcl
You should see the U-Boot SPL banner followed by the banner for U-Boot proper
in the output of openocd. The CMSIS-DAP adapter is slow, so this can take a
long time. If you don't see it, something has gone wrong. After a while, you
should see the prompt. You can load an image using semihosting by running::
=> load hostfs - $loadaddr <name of file>
Note that openocd's terminal is "cooked," so commands will only be sent to
U-Boot when you press enter, and all commands will be echoed twice.
Additionally, openocd will block when waiting for input, ignoring gdb, JTAG
events, and Ctrl-Cs. To make openocd process these events, just hit enter.
Using an external JTAG adapter
""""""""""""""""""""""""""""""
The CMSIS-DAP adapter can be rather slow. To speed up booting, use an external
JTAG adapter. The following examples assume you are using a J-Link, though any
adapter supported by OpenOCD will do. Ensure that ``SW4[7]`` is ``1``. Attach
your jtag adapter to J22. Modify ``u-boot.tcl`` and replace the first two lines
with the following::
# Load the J-Link configuration (or whatever your adapter is)
source [find interface/jlink.cfg]
# Use JTAG, since the J-Link also supports SWD
transport select jtag
# The reset pin resets the whole CPU
reset_config srst_only
# Load the LS1046A config
source [find target/ls1046a.cfg]
You can proceed as normal through the rest of the steps above. I got a speedup
of around 100x by using a J-Link.
Debug UART
----------
To enable the debug UART, enable the following config options::
CONFIG_DEBUG_UART_NS16550=y
CONFIG_DEBUG_UART_BASE=0x21c0500
CONFIG_DEBUG_UART_CLOCK=300000000
|
