blob: 692ab3d21d1216a740c0105885cd691368079609 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
.. SPDX-License-Identifier: GPL-2.0+
U-Boot for Khadas VIM3L
=======================
Khadas VIM3L is a single board computer manufactured by Shenzhen Wesion
Technology Co., Ltd. with the following specifications:
- Amlogic S905D3 Arm Cortex-A55 quad-core SoC
- 2GB LPDDR4 SDRAM
- Gigabit Ethernet
- HDMI 2.1 display
- 40-pin GPIO header
- 1 x USB 3.0 Host, 1 x USB 2.0 Host
- eMMC, microSD
- M.2
- Infrared receiver
Schematics are available on the manufacturer website.
PCIe Setup
----------
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.
To setup for PCIe, run the following commands from U-Boot:
.. code-block:: none
i2c dev i2c@5000
i2c mw 0x18 0x33 1
Then power-cycle the board.
To set back to USB3.0, run the following commands from U-Boot:
.. code-block:: none
i2c dev i2c@5000
i2c mw 0x18 0x33 0
Then power-cycle the board.
U-Boot compilation
------------------
.. code-block:: bash
$ export CROSS_COMPILE=aarch64-none-elf-
$ make khadas-vim3l_defconfig
$ make
Image creation
--------------
For simplified usage, pleaser refer to :doc:`pre-generated-fip` with codename `khadas-vim3l`
Amlogic doesn't provide sources for the firmware and for tools needed
to create the bootloader image, so it is necessary to obtain them from
the git tree published by the board vendor:
.. code-block:: bash
$ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
$ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
$ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
$ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
$ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
$ DIR=vim3l-u-boot
$ git clone --depth 1 \
https://github.com/khadas/u-boot.git -b khadas-vims-v2015.01 \
$DIR
$ cd vim3l-u-boot
$ make kvim3l_defconfig
$ make CROSS_COMPILE=aarch64-none-elf-
$ export UBOOTDIR=$PWD
Go back to mainline U-Boot source tree then :
.. code-block:: bash
$ mkdir fip
$ wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
$ cp $UBOOTDIR/build/scp_task/bl301.bin fip/
$ cp $UBOOTDIR/build/board/khadas/kvim3l/firmware/acs.bin fip/
$ cp $UBOOTDIR/fip/g12a/bl2.bin fip/
$ cp $UBOOTDIR/fip/g12a/bl30.bin fip/
$ cp $UBOOTDIR/fip/g12a/bl31.img fip/
$ cp $UBOOTDIR/fip/g12a/ddr3_1d.fw fip/
$ cp $UBOOTDIR/fip/g12a/ddr4_1d.fw fip/
$ cp $UBOOTDIR/fip/g12a/ddr4_2d.fw fip/
$ cp $UBOOTDIR/fip/g12a/diag_lpddr4.fw fip/
$ cp $UBOOTDIR/fip/g12a/lpddr3_1d.fw fip/
$ cp $UBOOTDIR/fip/g12a/lpddr4_1d.fw fip/
$ cp $UBOOTDIR/fip/g12a/lpddr4_2d.fw fip/
$ cp $UBOOTDIR/fip/g12a/piei.fw fip/
$ cp $UBOOTDIR/fip/g12a/aml_ddr.fw fip/
$ cp u-boot.bin fip/bl33.bin
$ bash fip/blx_fix.sh \
fip/bl30.bin \
fip/zero_tmp \
fip/bl30_zero.bin \
fip/bl301.bin \
fip/bl301_zero.bin \
fip/bl30_new.bin \
bl30
$ bash fip/blx_fix.sh \
fip/bl2.bin \
fip/zero_tmp \
fip/bl2_zero.bin \
fip/acs.bin \
fip/bl21_zero.bin \
fip/bl2_new.bin \
bl2
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl30sig --input fip/bl30_new.bin \
--output fip/bl30_new.bin.g12a.enc \
--level v3
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl30_new.bin.g12a.enc \
--output fip/bl30_new.bin.enc \
--level v3 --type bl30
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl31.img \
--output fip/bl31.img.enc \
--level v3 --type bl31
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl3sig --input fip/bl33.bin --compress lz4 \
--output fip/bl33.bin.enc \
--level v3 --type bl33 --compress lz4
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bl2sig --input fip/bl2_new.bin \
--output fip/bl2.n.bin.sig
$ $UBOOTDIR/fip/g12a/aml_encrypt_g12a --bootmk \
--output fip/u-boot.bin \
--bl2 fip/bl2.n.bin.sig \
--bl30 fip/bl30_new.bin.enc \
--bl31 fip/bl31.img.enc \
--bl33 fip/bl33.bin.enc \
--ddrfw1 fip/ddr4_1d.fw \
--ddrfw2 fip/ddr4_2d.fw \
--ddrfw3 fip/ddr3_1d.fw \
--ddrfw4 fip/piei.fw \
--ddrfw5 fip/lpddr4_1d.fw \
--ddrfw6 fip/lpddr4_2d.fw \
--ddrfw7 fip/diag_lpddr4.fw \
--ddrfw8 fip/aml_ddr.fw \
--ddrfw9 fip/lpddr3_1d.fw \
--level v3
and then write the image to SD with:
.. code-block:: bash
$ DEV=/dev/your_sd_device
$ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
$ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
|
