1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
|
Andes Technology SoC AE350
===========================
AE350 is the mainline SoC produced by Andes Technology using AX25 CPU core
base on RISC-V architecture.
AE350 has integrated both AHB and APB bus and many periphals for application
and product development.
AX25-AE350
=========
AX25-AE350 is the SoC with AE350 hardcore CPU.
Configurations
==============
CONFIG_SKIP_LOWLEVEL_INIT:
If you want to boot this system from SPI ROM and bypass e-bios (the
other boot loader on ROM). You should undefine CONFIG_SKIP_LOWLEVEL_INIT
in "include/configs/ax25-ae350.h".
Build and boot steps
====================
build:
1. Prepare the toolchains and make sure the $PATH to toolchains is correct.
2. Use `make ax25-ae350_defconfig` in u-boot root to build the image.
Verification
====================
Target
====================
1. startup
2. relocation
3. timer driver
4. uart driver
5. mac driver
6. mmc driver
7. spi driver
Steps
====================
1. Define CONFIG_SKIP_LOWLEVEL_INIT to build u-boot which is loaded via gdb from ram.
2. Undefine CONFIG_SKIP_LOWLEVEL_INIT to build u-boot which is booted from spi rom.
3. Ping a server by mac driver
4. Scan sd card and copy u-boot image which is booted from flash to ram by sd driver.
5. Burn this u-boot image to spi rom by spi driver
6. Re-boot u-boot from spi flash with power off and power on.
Messages of U-Boot boot on AE350 board
======================================
U-Boot 2018.01-rc2-00033-g824f89a (Dec 21 2017 - 16:51:26 +0800)
DRAM: 1 GiB
MMC: mmc@f0e00000: 0
SF: Detected mx25u1635e with page size 256 Bytes, erase size 4 KiB, total 2 MiB
In: serial@f0300000
Out: serial@f0300000
Err: serial@f0300000
Net:
Warning: mac@e0100000 (eth0) using random MAC address - be:dd:d7:e4:e8:10
eth0: mac@e0100000
RISC-V # version
U-Boot 2018.01-rc2-00033-gb265b91-dirty (Dec 22 2017 - 13:54:21 +0800)
riscv32-unknown-linux-gnu-gcc (GCC) 7.2.0
GNU ld (GNU Binutils) 2.29
RISC-V # setenv ipaddr 10.0.4.200 ;
RISC-V # setenv serverip 10.0.4.97 ;
RISC-V # ping 10.0.4.97 ;
Using mac@e0100000 device
host 10.0.4.97 is alive
RISC-V # mmc rescan
RISC-V # fatls mmc 0:1
318907 u-boot-ae350-64.bin
1252 hello_world_ae350_32.bin
328787 u-boot-ae350-32.bin
3 file(s), 0 dir(s)
RISC-V # sf probe 0:0 50000000 0
SF: Detected mx25u1635e with page size 256 Bytes, erase size 4 KiB, total 2 MiB
RISC-V # sf test 0x100000 0x1000
SPI flash test:
0 erase: 36 ticks, 111 KiB/s 0.888 Mbps
1 check: 29 ticks, 137 KiB/s 1.096 Mbps
2 write: 40 ticks, 100 KiB/s 0.800 Mbps
3 read: 20 ticks, 200 KiB/s 1.600 Mbps
Test passed
0 erase: 36 ticks, 111 KiB/s 0.888 Mbps
1 check: 29 ticks, 137 KiB/s 1.096 Mbps
2 write: 40 ticks, 100 KiB/s 0.800 Mbps
3 read: 20 ticks, 200 KiB/s 1.600 Mbps
RISC-V # fatload mmc 0:1 0x600000 u-boot-ae350-32.bin
reading u-boot-ae350-32.bin
328787 bytes read in 324 ms (990.2 KiB/s)
RISC-V # sf erase 0x0 0x51000
SF: 331776 bytes @ 0x0 Erased: OK
RISC-V # sf write 0x600000 0x0 0x50453
device 0 offset 0x0, size 0x50453
SF: 328787 bytes @ 0x0 Written: OK
RISC-V # crc32 0x600000 0x50453
crc32 for 00600000 ... 00650452 ==> 692dc44a
RISC-V # crc32 0x80000000 0x50453
crc32 for 80000000 ... 80050452 ==> 692dc44a
RISC-V #
*** power-off and power-on, this U-Boot is booted from spi flash ***
U-Boot 2018.01-rc2-00032-gf67dd47-dirty (Dec 21 2017 - 13:56:03 +0800)
DRAM: 1 GiB
MMC: mmc@f0e00000: 0
SF: Detected mx25u1635e with page size 256 Bytes, erase size 4 KiB, total 2 MiB
In: serial@f0300000
Out: serial@f0300000
Err: serial@f0300000
Net:
Warning: mac@e0100000 (eth0) using random MAC address - ee:4c:58:29:32:f5
eth0: mac@e0100000
RISC-V #
Boot bbl and riscv-linux via U-Boot on QEMU
===========================================
1. Build riscv-linux
2. Build bbl and riscv-linux with --with-payload
3. Prepare ae350.dtb
4. Creating OS-kernel images
./mkimage -A riscv -O linux -T kernel -C none -a 0x0000 -e 0x0000 -d bbl.bin bootmImage-bbl.bin
Image Name:
Created: Tue Mar 13 10:06:42 2018
Image Type: RISC-V Linux Kernel Image (uncompressed)
Data Size: 17901204 Bytes = 17481.64 KiB = 17.07 MiB
Load Address: 00000000
Entry Point: 00000000
4. Copy bootmImage-bbl.bin and ae350.dtb to qemu sd card image
5. Message of booting riscv-linux from bbl via u-boot on qemu
U-Boot 2018.03-rc4-00031-g2631273 (Mar 13 2018 - 15:02:55 +0800)
DRAM: 1 GiB
main-loop: WARNING: I/O thread spun for 1000 iterations
MMC: mmc@f0e00000: 0
Loading Environment from SPI Flash... *** Warning - spi_flash_probe_bus_cs() failed, using default environment
Failed (-22)
In: serial@f0300000
Out: serial@f0300000
Err: serial@f0300000
Net:
Warning: mac@e0100000 (eth0) using random MAC address - 02:00:00:00:00:00
eth0: mac@e0100000
RISC-V # mmc rescan
RISC-V # mmc part
Partition Map for MMC device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
RISC-V # fatls mmc 0:0
17901268 bootmImage-bbl.bin
1954 ae2xx.dtb
2 file(s), 0 dir(s)
RISC-V # fatload mmc 0:0 0x00600000 bootmImage-bbl.bin
17901268 bytes read in 4642 ms (3.7 MiB/s)
RISC-V # fatload mmc 0:0 0x2000000 ae350.dtb
1954 bytes read in 1 ms (1.9 MiB/s)
RISC-V # setenv bootm_size 0x2000000
RISC-V # setenv fdt_high 0x1f00000
RISC-V # bootm 0x00600000 - 0x2000000
## Booting kernel from Legacy Image at 00600000 ...
Image Name:
Image Type: RISC-V Linux Kernel Image (uncompressed)
Data Size: 17901204 Bytes = 17.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 02000000
Booting using the fdt blob at 0x2000000
Loading Kernel Image ... OK
Loading Device Tree to 0000000001efc000, end 0000000001eff7a1 ... OK
[ 0.000000] OF: fdt: Ignoring memory range 0x0 - 0x200000
[ 0.000000] Linux version 4.14.0-00046-gf3e439f-dirty (rick@atcsqa06) (gcc version 7.1.1 20170509 (GCC)) #1 Tue Jan 9 16:34:25 CST 2018
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] Initial ramdisk at: 0xffffffe000016a98 (12267008 bytes)
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000200000-0x000000007fffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000200000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x000000007fffffff]
[ 0.000000] elf_hwcap is 0x112d
[ 0.000000] random: fast init done
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516615
[ 0.000000] Kernel command line: console=ttyS0,38400n8 earlyprintk=uart8250-32bit,0xf0300000 debug loglevel=7
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 2047832K/2095104K available (1856K kernel code, 204K rwdata, 532K rodata, 12076K init, 756K bss, 47272K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] riscv,cpu_intc,0: 64 local interrupts mapped
[ 0.000000] riscv,plic0,e4000000: mapped 31 interrupts to 1/2 handlers
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns
[ 0.000000] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj=40000)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.004000] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.004000] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.056000] devtmpfs: initialized
[ 0.060000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.064000] futex hash table entries: 256 (order: 0, 6144 bytes)
[ 0.068000] NET: Registered protocol family 16
[ 0.080000] vgaarb: loaded
[ 0.084000] clocksource: Switched to clocksource riscv_clocksource
[ 0.088000] NET: Registered protocol family 2
[ 0.092000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.096000] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.096000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.100000] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.100000] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.104000] NET: Registered protocol family 1
[ 0.616000] Unpacking initramfs...
[ 1.220000] workingset: timestamp_bits=62 max_order=19 bucket_order=0
[ 1.244000] io scheduler noop registered
[ 1.244000] io scheduler cfq registered (default)
[ 1.244000] io scheduler mq-deadline registered
[ 1.248000] io scheduler kyber registered
[ 1.360000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.368000] console [ttyS0] disabled
[ 1.372000] f0300000.serial: ttyS0 at MMIO 0xf0300020 (irq = 10, base_baud = 1228800) is a 16550A
[ 1.392000] console [ttyS0] enabled
[ 1.392000] ftmac100: Loading version 0.2 ...
[ 1.396000] ftmac100 e0100000.mac eth0: irq 8, mapped at ffffffd002005000
[ 1.400000] ftmac100 e0100000.mac eth0: generated random MAC address 6e:ac:c3:92:36:c0
[ 1.404000] IR NEC protocol handler initialized
[ 1.404000] IR RC5(x/sz) protocol handler initialized
[ 1.404000] IR RC6 protocol handler initialized
[ 1.404000] IR JVC protocol handler initialized
[ 1.408000] IR Sony protocol handler initialized
[ 1.408000] IR SANYO protocol handler initialized
[ 1.408000] IR Sharp protocol handler initialized
[ 1.408000] IR MCE Keyboard/mouse protocol handler initialized
[ 1.412000] IR XMP protocol handler initialized
[ 1.456000] ftsdc010 f0e00000.mmc: mmc0 - using hw SDIO IRQ
[ 1.464000] bootconsole [early0] uses init memory and must be disabled even before the real one is ready
[ 1.464000] bootconsole [early0] disabled
[ 1.508000] Freeing unused kernel memory: 12076K
[ 1.512000] This architecture does not have kernel memory protection.
[ 1.520000] mmc0: new SD card at address 4567
[ 1.524000] mmcblk0: mmc0:4567 QEMU! 20.0 MiB
[ 1.844000] mmcblk0:
Wed Dec 1 10:00:00 CST 2010
/ #
TODO
==================================================
Boot bbl and riscv-linux via U-Boot on AE350 board
|
