1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
|
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2008
* Grazvydas Ignotas <notasas@gmail.com>
*
* Derived from Beagle Board, 3430 SDP, and OMAP3EVM code by
* Richard Woodruff <r-woodruff2@ti.com>
* Syed Mohammed Khasim <khasim@ti.com>
* Sunil Kumar <sunilsaini05@gmail.com>
* Shashi Ranjan <shashiranjanmca05@gmail.com>
*
* (C) Copyright 2004-2008
* Texas Instruments, <www.ti.com>
*/
#include <common.h>
#include <dm.h>
#include <init.h>
#include <ns16550.h>
#include <twl4030.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/mux.h>
#include <asm/arch/gpio.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-types.h>
#include "pandora.h"
DECLARE_GLOBAL_DATA_PTR;
#define TWL4030_BB_CFG_BBCHEN (1 << 4)
#define TWL4030_BB_CFG_BBSEL_3200MV (3 << 2)
#define TWL4030_BB_CFG_BBISEL_500UA 2
#define CONTROL_WKUP_CTRL 0x48002a5c
#define GPIO_IO_PWRDNZ (1 << 6)
#define PBIASLITEVMODE1 (1 << 8)
static const struct ns16550_platdata pandora_serial = {
.base = OMAP34XX_UART3,
.reg_shift = 2,
.clock = V_NS16550_CLK,
.fcr = UART_FCR_DEFVAL,
};
U_BOOT_DEVICE(pandora_uart) = {
"ns16550_serial",
&pandora_serial
};
/*
* Routine: board_init
* Description: Early hardware init.
*/
int board_init(void)
{
gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
/* board id for Linux */
gd->bd->bi_arch_number = MACH_TYPE_OMAP3_PANDORA;
/* boot param addr */
gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
return 0;
}
static void set_output_gpio(unsigned int gpio, int value)
{
int ret;
ret = gpio_request(gpio, "");
if (ret != 0) {
printf("could not request GPIO %u\n", gpio);
return;
}
ret = gpio_direction_output(gpio, value);
if (ret != 0)
printf("could not set GPIO %u to %d\n", gpio, value);
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
t2_t *t2_base = (t2_t *)T2_BASE;
u32 pbias_lite;
twl4030_led_init(TWL4030_LED_LEDEN_LEDBON);
/* set up dual-voltage GPIOs to 1.8V */
pbias_lite = readl(&t2_base->pbias_lite);
pbias_lite &= ~PBIASLITEVMODE1;
pbias_lite |= PBIASLITEPWRDNZ1;
writel(pbias_lite, &t2_base->pbias_lite);
if (get_cpu_family() == CPU_OMAP36XX)
writel(readl(CONTROL_WKUP_CTRL) | GPIO_IO_PWRDNZ,
CONTROL_WKUP_CTRL);
/* make sure audio and BT chips are in powerdown state */
set_output_gpio(14, 0);
set_output_gpio(15, 0);
set_output_gpio(118, 0);
/* enable USB supply */
set_output_gpio(164, 1);
/* wifi needs a short pulse to enter powersave state */
set_output_gpio(23, 1);
udelay(5000);
gpio_direction_output(23, 0);
/* Enable battery backup capacitor (3.2V, 0.5mA charge current) */
twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
TWL4030_PM_RECEIVER_BB_CFG,
TWL4030_BB_CFG_BBCHEN | TWL4030_BB_CFG_BBSEL_3200MV |
TWL4030_BB_CFG_BBISEL_500UA);
omap_die_id_display();
return 0;
}
/*
* Routine: set_muxconf_regs
* Description: Setting up the configuration Mux registers specific to the
* hardware. Many pins need to be moved from protect to primary
* mode.
*/
void set_muxconf_regs(void)
{
MUX_PANDORA();
if (get_cpu_family() == CPU_OMAP36XX) {
MUX_PANDORA_3730();
}
}
#ifdef CONFIG_MMC
int board_mmc_init(bd_t *bis)
{
return omap_mmc_init(0, 0, 0, -1, -1);
}
void board_mmc_power_init(void)
{
twl4030_power_mmc_init(0);
}
#endif
|
