| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Read the tristate config for all the pins and display it.
ZynqMP> pinmux status MIO1
MIO1: slew:fast bias:enabled pull:up input:cmos drive:12mA
volt:1.8 tri_state:enabled
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230914100620.26346-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Add support to handle 'output-enable' and 'bias-high-impedance'
configurations in pinctrl driver.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230811054829.13162-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Support for configuring TRISTATE parameter is added in ZYNQMP PMUFW(Xilinx
ZynqMP Platform Management Firmware) Configuration Param Set version 2.0.
If the requested configuration is TRISTATE then check the version before
requesting Xilinx firmware to set the configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230811054829.13162-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Update my and DPs email address to match current setup.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/aba5b19b9c5a95608829e86ad5cc4671c940f1bb.1688992543.git.michal.simek@amd.com
|
|
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This reverts commit 123462e5e534d6e17b1b7d2006734bbe54b03e0a.
On systems with older PMUFW using these pinctrl properties can cause system
hang because there is missing feature autodetection.
When it is implemented support for these two properties should go back.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c2900319ea80484f21692997f296269aee701c1f.1665659138.git.michal.simek@amd.com
|
|
Add support to handle 'output-enable' and 'bias-high-impedance'
configurations. DT property output-enable brings out the pins from
tri-state, whereas bias-high-impedance changes the pins state to
tri-state.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1a02cd41d183d397ebce23c497178281c7286692.1655286745.git.michal.simek@amd.com
|
|
Add pinctrl driver for Xilinx ZynqMP SOC. This driver is compatible with
linux device tree parameters for configuring pinmux and pinconf.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2d7eefa83c8c0129f7243a25de56a289e948f6c6.1645626183.git.michal.simek@xilinx.com
|
