diff options
Diffstat (limited to 'doc/develop/uefi/uefi.rst')
| -rw-r--r-- | doc/develop/uefi/uefi.rst | 124 |
1 files changed, 0 insertions, 124 deletions
diff --git a/doc/develop/uefi/uefi.rst b/doc/develop/uefi/uefi.rst index f17138f5c7..4f2b8b036d 100644 --- a/doc/develop/uefi/uefi.rst +++ b/doc/develop/uefi/uefi.rst @@ -277,130 +277,6 @@ Enable ``CONFIG_OPTEE``, ``CONFIG_CMD_OPTEE_RPMB`` and ``CONFIG_EFI_MM_COMM_TEE` [1] https://optee.readthedocs.io/en/latest/building/efi_vars/stmm.html -Enabling UEFI Capsule Update feature -~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ - -Support has been added for the UEFI capsule update feature which -enables updating the U-Boot image using the UEFI firmware management -protocol (FMP). The capsules are not passed to the firmware through -the UpdateCapsule runtime service. Instead, capsule-on-disk -functionality is used for fetching the capsule from the EFI System -Partition (ESP) by placing the capsule file under the -\EFI\UpdateCapsule directory. - -The directory \EFI\UpdateCapsule is checked for capsules only within the -EFI system partition on the device specified in the active boot option -determined by reference to BootNext variable or BootOrder variable processing. -The active Boot Variable is the variable with highest priority BootNext or -within BootOrder that refers to a device found to be present. Boot variables -in BootOrder but referring to devices not present are ignored when determining -active boot variable. -Before starting a capsule update make sure your capsules are installed in the -correct ESP partition or set BootNext. - -Performing the update -********************* - -Since U-boot doesn't currently support SetVariable at runtime there's a Kconfig -option (CONFIG_EFI_IGNORE_OSINDICATIONS) to disable the OsIndications variable -check. If that option is enabled just copy your capsule to \EFI\UpdateCapsule. - -If that option is disabled, you'll need to set the OsIndications variable with:: - - => setenv -e -nv -bs -rt -v OsIndications =0x04 - -Finally, the capsule update can be initiated either by rebooting the board, -which is the preferred method, or by issuing the following command:: - - => efidebug capsule disk-update - -**The efidebug command is should only be used during debugging/development.** - -Enabling Capsule Authentication -******************************* - -The UEFI specification defines a way of authenticating the capsule to -be updated by verifying the capsule signature. The capsule signature -is computed and prepended to the capsule payload at the time of -capsule generation. This signature is then verified by using the -public key stored as part of the X509 certificate. This certificate is -in the form of an efi signature list (esl) file, which is embedded as -part of U-Boot. - -The capsule authentication feature can be enabled through the -following config, in addition to the configs listed above for capsule -update:: - - CONFIG_EFI_CAPSULE_AUTHENTICATE=y - CONFIG_EFI_CAPSULE_KEY_PATH=<path to .esl cert> - -The public and private keys used for the signing process are generated -and used by the steps highlighted below:: - - 1. Install utility commands on your host - * OPENSSL - * efitools - - 2. Create signing keys and certificate files on your host - - $ openssl req -x509 -sha256 -newkey rsa:2048 -subj /CN=CRT/ \ - -keyout CRT.key -out CRT.crt -nodes -days 365 - $ cert-to-efi-sig-list CRT.crt CRT.esl - - $ openssl x509 -in CRT.crt -out CRT.cer -outform DER - $ openssl x509 -inform DER -in CRT.cer -outform PEM -out CRT.pub.pem - - $ openssl pkcs12 -export -out CRT.pfx -inkey CRT.key -in CRT.crt - $ openssl pkcs12 -in CRT.pfx -nodes -out CRT.pem - -The capsule file can be generated by using the GenerateCapsule.py -script in EDKII:: - - $ ./BaseTools/BinWrappers/PosixLike/GenerateCapsule -e -o \ - <capsule_file_name> --monotonic-count <val> --fw-version \ - <val> --lsv <val> --guid \ - e2bb9c06-70e9-4b14-97a3-5a7913176e3f --verbose \ - --update-image-index <val> --signer-private-cert \ - /path/to/CRT.pem --trusted-public-cert \ - /path/to/CRT.pub.pem --other-public-cert /path/to/CRT.pub.pem \ - <u-boot.bin> - -Place the capsule generated in the above step on the EFI System -Partition under the EFI/UpdateCapsule directory - -Testing on QEMU -*************** - -Currently, support has been added on the QEMU ARM64 virt platform for -updating the U-Boot binary as a raw image when the platform is booted -in non-secure mode, i.e. with CONFIG_TFABOOT disabled. For this -configuration, the QEMU platform needs to be booted with -'secure=off'. The U-Boot binary placed on the first bank of the NOR -flash at offset 0x0. The U-Boot environment is placed on the second -NOR flash bank at offset 0x4000000. - -The capsule update feature is enabled with the following configuration -settings:: - - CONFIG_MTD=y - CONFIG_FLASH_CFI_MTD=y - CONFIG_CMD_MTDPARTS=y - CONFIG_CMD_DFU=y - CONFIG_DFU_MTD=y - CONFIG_PCI_INIT_R=y - CONFIG_EFI_CAPSULE_ON_DISK=y - CONFIG_EFI_CAPSULE_FIRMWARE_MANAGEMENT=y - CONFIG_EFI_CAPSULE_FIRMWARE=y - CONFIG_EFI_CAPSULE_FIRMWARE_RAW=y - -In addition, the following config needs to be disabled(QEMU ARM specific):: - - CONFIG_TFABOOT - -The capsule file can be generated by using the tools/mkeficapsule:: - - $ mkeficapsule --raw <u-boot.bin> --index 1 <capsule_file_name> - Executing the boot manager ~~~~~~~~~~~~~~~~~~~~~~~~~~ |