nios2: add 10m50 devboard support

Add 10m50 devboard support. It is based on the Golden Hardware
Reference Design (GHRD), available at,

http://rocketboards.org/foswiki/view/Documentation/
AlteraMAX1010M50RevCDevelopmentKitLinuxSetup

Though we supported only one nios2-generic board in the past. Now,
with the removal of the nios2-generic board dir, adding new nios2
boards to u-boot is easier than before. It should be helpful to
add those boards supported in Linux mainline. There are only two
such nios2 boards, the 3c120 devboard and 10m50 devboard. The
nios2-generic is actually 3c120, and should restore the name. The
10m50 is this one.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>

1 files changed, 103 insertions, 0 deletions

diff --git a/include/configs/10m50_devboard.h b/include/configs/10m50_devboard.h
new file mode 100644
index 0000000000..ab7dd08914
--- /dev/null
+++ b/include/configs/10m50_devboard.h
@@ -0,0 +1,103 @@
+/*
+ * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ * (C) Copyright 2010, Thomas Chou <thomas@wytron.com.tw>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * BOARD/CPU
+ */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+/*
+ * SERIAL
+ */
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_CONSOLE_INFO_QUIET	/* Suppress console info */
+
+/*
+ * Flash
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_MAX_FLASH_SECT	1024
+#define CONFIG_MTD_DEVICE
+
+/*
+ * NET options
+ */
+#define CONFIG_SYS_RX_ETH_BUFFER	0
+#define CONFIG_CMD_MII
+#define CONFIG_PHY_GIGE
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#define CONFIG_PHY_MARVELL
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * FDT options
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_LMB
+
+/*
+ * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
+ * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
+ * reset address, no? This will keep the environment in user region
+ * of flash. NOTE: the monitor length must be multiple of sector size
+ * (which is common practice).
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+
+#define CONFIG_ENV_SIZE			0x10000	/* 64k, 1 sector */
+#define CONFIG_ENV_OVERWRITE		/* Serial change Ok	*/
+#define CONFIG_ENV_ADDR			0xf4040000
+
+/*
+ * MEMORY ORGANIZATION
+ * -Monitor at top of sdram.
+ * -The heap is placed below the monitor
+ * -The stack is placed below the heap (&grows down).
+ */
+#define CONFIG_SYS_SDRAM_BASE		0xc8000000
+#define CONFIG_SYS_SDRAM_SIZE		0x08000000
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_MONITOR_IS_IN_RAM
+#define CONFIG_SYS_MONITOR_LEN		0x40000	/* Reserve 256k */
+#define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_SDRAM_BASE + \
+					 CONFIG_SYS_SDRAM_SIZE - \
+					 CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_SYS_MALLOC_LEN		0x20000
+
+/*
+ * MISC
+ */
+#define CONFIG_SYS_LONGHELP		/* Provide extended help */
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O buf size */
+#define CONFIG_SYS_MAXARGS		16	/* Max command args	*/
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Bootarg buf size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + \
+					 16)	/* Print buf size */
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MONITOR_BASE - \
+					 CONFIG_ENV_SIZE - \
+					 CONFIG_SYS_MALLOC_LEN -	\
+					 0x10000)
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_CMD_GPIO
+
+#endif /* __CONFIG_H */