MPC5121: Add USB EHCI support

Signed-off-by: Francesco Rendine <francesco.rendine@valueteam.com>
Signed-off-by: Damien Dusha <d.dusha@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Coding style cleanup; slight file restructuring.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>

1 files changed, 122 insertions, 26 deletions

diff --git a/include/usb/ehci-fsl.h b/include/usb/ehci-fsl.h
index f48945a27a..08691a0f2a 100644
--- a/include/usb/ehci-fsl.h
+++ b/include/usb/ehci-fsl.h
@@ -35,12 +35,17 @@
 #define PORT_PTS_ULPI		(2 << 30)
 #define PORT_PTS_SERIAL		(3 << 30)
 #define PORT_PTS_PTW		(1 << 28)
+#define PORT_PFSC		(1 << 24) /* Defined on Page 39-44 of the mpc5151 ERM */
+#define PORT_PTS_PHCD		(1 << 23)
+#define PORT_PP			(1 << 12)
+#define PORT_PR			(1 << 8)
 
 /* USBMODE Register bits */
 #define CM_IDLE			(0 << 0)
 #define CM_RESERVED		(1 << 0)
 #define CM_DEVICE		(2 << 0)
 #define CM_HOST			(3 << 0)
+#define ES_BE			(1 << 2)	/* Big Endian Select, default is LE */
 #define USBMODE_RESERVED_2	(0 << 2)
 #define SLOM			(1 << 3)
 #define SDIS			(1 << 4)
@@ -70,7 +75,78 @@
 #define PHY_CLK_VALID		(1 << 17)
 
 #define FSL_SOC_USB_PORTSC2	0x188
+
+/* OTG Status Control Register bits */
+#define FSL_SOC_USB_OTGSC	0x1a4
+#define CTRL_VBUS_DISCHARGE	(0x1<<0)
+#define CTRL_VBUS_CHARGE	(0x1<<1)
+#define CTRL_OTG_TERMINATION	(0x1<<3)
+#define CTRL_DATA_PULSING	(0x1<<4)
+#define CTRL_ID_PULL_EN		(0x1<<5)
+#define HA_DATA_PULSE		(0x1<<6)
+#define HA_BA			(0x1<<7)
+#define STS_USB_ID		(0x1<<8)
+#define STS_A_VBUS_VALID	(0x1<<9)
+#define STS_A_SESSION_VALID	(0x1<<10)
+#define STS_B_SESSION_VALID	(0x1<<11)
+#define STS_B_SESSION_END	(0x1<<12)
+#define STS_1MS_TOGGLE		(0x1<<13)
+#define STS_DATA_PULSING	(0x1<<14)
+#define INTSTS_USB_ID		(0x1<<16)
+#define INTSTS_A_VBUS_VALID	(0x1<<17)
+#define INTSTS_A_SESSION_VALID	(0x1<<18)
+#define INTSTS_B_SESSION_VALID	(0x1<<19)
+#define INTSTS_B_SESSION_END	(0x1<<20)
+#define INTSTS_1MS		(0x1<<21)
+#define INTSTS_DATA_PULSING	(0x1<<22)
+#define INTR_USB_ID_EN		(0x1<<24)
+#define INTR_A_VBUS_VALID_EN	(0x1<<25)
+#define INTR_A_SESSION_VALID_EN (0x1<<26)
+#define INTR_B_SESSION_VALID_EN (0x1<<27)
+#define INTR_B_SESSION_END_EN	(0x1<<28)
+#define INTR_1MS_TIMER_EN	(0x1<<29)
+#define INTR_DATA_PULSING_EN	(0x1<<30)
+#define INTSTS_MASK		(0x00ff0000)
+
+/* USBCMD Bits of interest */
+#define EHCI_FSL_USBCMD_RST	(1 <<  1)
+#define EHCI_FSL_USBCMD_RS	(1 <<  0)
+
+#define  INTERRUPT_ENABLE_BITS_MASK  \
+		(INTR_USB_ID_EN		| \
+		INTR_1MS_TIMER_EN	| \
+		INTR_A_VBUS_VALID_EN	| \
+		INTR_A_SESSION_VALID_EN | \
+		INTR_B_SESSION_VALID_EN | \
+		INTR_B_SESSION_END_EN	| \
+		INTR_DATA_PULSING_EN)
+
+#define  INTERRUPT_STATUS_BITS_MASK  \
+		(INTSTS_USB_ID		| \
+		INTR_1MS_TIMER_EN	| \
+		INTSTS_A_VBUS_VALID	| \
+		INTSTS_A_SESSION_VALID  | \
+		INTSTS_B_SESSION_VALID  | \
+		INTSTS_B_SESSION_END	| \
+		INTSTS_DATA_PULSING)
+
 #define FSL_SOC_USB_USBMODE	0x1a8
+
+#define USBGENCTRL		0x200		/* NOTE: big endian */
+#define GC_WU_INT_CLR		(1 << 5)	/* Wakeup int clear */
+#define GC_ULPI_SEL		(1 << 4)	/* ULPI i/f select (usb0 only)*/
+#define GC_PPP			(1 << 3)	/* Port Power Polarity */
+#define GC_PFP			(1 << 2)	/* Power Fault Polarity */
+#define GC_WU_ULPI_EN		(1 << 1)	/* Wakeup on ULPI event */
+#define GC_WU_IE		(1 << 1)	/* Wakeup interrupt enable */
+
+#define ISIPHYCTRL		0x204		/* NOTE: big endian */
+#define PHYCTRL_PHYE		(1 << 4)	/* On-chip UTMI PHY enable */
+#define PHYCTRL_BSENH		(1 << 3)	/* Bit Stuff Enable High */
+#define PHYCTRL_BSEN		(1 << 2)	/* Bit Stuff Enable */
+#define PHYCTRL_LSFE		(1 << 1)	/* Line State Filter Enable */
+#define PHYCTRL_PXE		(1 << 0)	/* PHY oscillator enable */
+
 #define FSL_SOC_USB_SNOOP1	0x400	/* NOTE: big-endian */
 #define FSL_SOC_USB_SNOOP2	0x404	/* NOTE: big-endian */
 #define FSL_SOC_USB_AGECNTTHRSH	0x408	/* NOTE: big-endian */
@@ -85,65 +161,85 @@
 #define MPC83XX_SCCR_USB_DRCM_01	0x00100000
 #define MPC83XX_SCCR_USB_DRCM_10	0x00200000
 
-#if defined(CONFIG_MPC83xx)
-#define CONFIG_SYS_MPC8xxx_USB_ADDR CONFIG_SYS_MPC83xx_USB_ADDR
+#if defined(CONFIG_MPC83XX)
+#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC83xx_USB_ADDR
 #elif defined(CONFIG_MPC85xx)
-#define CONFIG_SYS_MPC8xxx_USB_ADDR CONFIG_SYS_MPC85xx_USB_ADDR
+#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC85xx_USB_ADDR
+#elif defined(CONFIG_MPC512X)
+#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC512x_USB_ADDR
 #endif
 
 /*
  * USB Registers
  */
 struct usb_ehci {
-	u8	res1[0x100];
+	u32	id;		/* 0x000 - Identification register */
+	u32	hwgeneral;	/* 0x004 - General hardware parameters */
+	u32	hwhost;		/* 0x008 - Host hardware parameters */
+	u32	hwdevice;	/* 0x00C - Device hardware parameters  */
+	u32	hwtxbuf;	/* 0x010 - TX buffer hardware parameters */
+	u32	hwrxbuf;	/* 0x014 - RX buffer hardware parameters */
+	u8	res1[0x68];
+	u32	gptimer0_ld;	/* 0x080 - General Purpose Timer 0 load value */
+	u32	gptimer0_ctrl;	/* 0x084 - General Purpose Timer 0 control */
+	u32     gptimer1_ld;	/* 0x088 - General Purpose Timer 1 load value */
+	u32     gptimer1_ctrl;	/* 0x08C - General Purpose Timer 1 control */
+	u32	sbuscfg;	/* 0x090 - System Bus Interface Control */
+	u8	res2[0x6C];
 	u16	caplength;	/* 0x100 - Capability Register Length */
 	u16	hciversion;	/* 0x102 - Host Interface Version */
 	u32	hcsparams;	/* 0x104 - Host Structural Parameters */
 	u32	hccparams;	/* 0x108 - Host Capability Parameters */
-	u8	res2[0x14];
+	u8	res3[0x14];
 	u32	dciversion;	/* 0x120 - Device Interface Version */
 	u32	dciparams;	/* 0x124 - Device Controller Params */
-	u8	res3[0x18];
+	u8	res4[0x18];
 	u32	usbcmd;		/* 0x140 - USB Command */
 	u32	usbsts;		/* 0x144 - USB Status */
 	u32	usbintr;	/* 0x148 - USB Interrupt Enable */
 	u32	frindex;	/* 0x14C - USB Frame Index */
-	u8	res4[0x4];
+	u8	res5[0x4];
 	u32	perlistbase;	/* 0x154 - Periodic List Base
 					 - USB Device Address */
 	u32	ep_list_addr;	/* 0x158 - Next Asynchronous List
-					 - Endpoint Address */
-	u8	res5[0x4];
+					 - End Point Address */
+	u8	res6[0x4];
 	u32	burstsize;	/* 0x160 - Programmable Burst Size */
+#define FSL_EHCI_TXPBURST(X)	((X) << 8)
+#define FSL_EHCI_RXPBURST(X)	(X)
 	u32	txfilltuning;	/* 0x164 - Host TT Transmit
 					   pre-buffer packet tuning */
-	u8	res6[0x8];
+	u8	res7[0x8];
 	u32	ulpi_viewpoint;	/* 0x170 - ULPI Reister Access */
-	u8	res7[0xc];
+	u8	res8[0xc];
 	u32	config_flag;	/* 0x180 - Configured Flag Register */
 	u32	portsc;		/* 0x184 - Port status/control */
-	u8	res8[0x20];
+	u8	res9[0x1C];
+	u32	otgsc;		/* 0x1a4 - Oo-The-Go status and control */
 	u32	usbmode;	/* 0x1a8 - USB Device Mode */
-	u32	epsetupstat;	/* 0x1ac - Endpoint Setup Status */
-	u32	epprime;	/* 0x1b0 - Endpoint Init Status */
-	u32	epflush;	/* 0x1b4 - Endpoint De-initlialize */
-	u32	epstatus;	/* 0x1b8 - Endpoint Status */
-	u32	epcomplete;	/* 0x1bc - Endpoint Complete */
-	u32	epctrl0;	/* 0x1c0 - Endpoint Control 0 */
-	u32	epctrl1;	/* 0x1c4 - Endpoint Control 1 */
-	u32	epctrl2;	/* 0x1c8 - Endpoint Control 2 */
-	u32	epctrl3;	/* 0x1cc - Endpoint Control 3 */
-	u32	epctrl4;	/* 0x1d0 - Endpoint Control 4 */
-	u32	epctrl5;	/* 0x1d4 - Endpoint Control 5 */
-	u8	res9[0x228];
+	u32	epsetupstat;	/* 0x1ac - End Point Setup Status */
+	u32	epprime;	/* 0x1b0 - End Point Init Status */
+	u32	epflush;	/* 0x1b4 - End Point De-initlialize */
+	u32	epstatus;	/* 0x1b8 - End Point Status */
+	u32	epcomplete;	/* 0x1bc - End Point Complete */
+	u32	epctrl0;	/* 0x1c0 - End Point Control 0 */
+	u32	epctrl1;	/* 0x1c4 - End Point Control 1 */
+	u32	epctrl2;	/* 0x1c8 - End Point Control 2 */
+	u32	epctrl3;	/* 0x1cc - End Point Control 3 */
+	u32	epctrl4;	/* 0x1d0 - End Point Control 4 */
+	u32	epctrl5;	/* 0x1d4 - End Point Control 5 */
+	u8	res10[0x28];
+	u32	usbgenctrl;	/* 0x200 - USB General Control */
+	u32	isiphyctrl;	/* 0x204 - On-Chip PHY Control */
+	u8	res11[0x1F8];
 	u32	snoop1;		/* 0x400 - Snoop 1 */
 	u32	snoop2;		/* 0x404 - Snoop 2 */
 	u32	age_cnt_limit;	/* 0x408 - Age Count Threshold */
 	u32	prictrl;	/* 0x40c - Priority Control */
 	u32	sictrl;		/* 0x410 - System Interface Control */
-	u8	res10[0xEC];
+	u8	res12[0xEC];
 	u32	control;	/* 0x500 - Control */
-	u8	res11[0xafc];
+	u8	res13[0xafc];
 };
 
 #endif /* _EHCI_FSL_H */