ppc: Remove MPC837XEMDS board

This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

1 files changed, 0 insertions, 370 deletions

diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h
deleted file mode 100644
index c42cb426d8..0000000000
--- a/include/configs/MPC837XEMDS.h
+++ /dev/null
@@ -1,370 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc.
- * Dave Liu <daveliu@freescale.com>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300		1 /* E300 family */
-
-/*
- * IP blocks clock configuration
- */
-#define CONFIG_SYS_SCCR_TSEC1CM	1	/* CSB:eTSEC1 = 1:1 */
-#define CONFIG_SYS_SCCR_TSEC2CM	1	/* CSB:eTSEC2 = 1:1 */
-#define CONFIG_SYS_SCCR_SATACM	SCCR_SATACM_2	/* CSB:SATA[0:3] = 2:1 */
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH		0x00000000
-#define CONFIG_SYS_SICRL		0x00000000
-
-/*
- * Output Buffer Impedance
- */
-#define CONFIG_SYS_OBIR		0x31100000
-
-#define CONFIG_HWCONFIG
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-#define CONFIG_SYS_83XX_DDR_USES_CS0
-#define CONFIG_SYS_DDRCDR_VALUE		(DDRCDR_DHC_EN \
-					| DDRCDR_ODT \
-					| DDRCDR_Q_DRN)
-					/* 0x80080001 */ /* ODT 150ohm on SoC */
-
-#undef CONFIG_DDR_ECC		/* support DDR ECC function */
-#undef CONFIG_DDR_ECC_CMD	/* Use DDR ECC user commands */
-
-#define CONFIG_SPD_EEPROM	/* Use SPD EEPROM for DDR setup */
-#define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */
-
-#if defined(CONFIG_SPD_EEPROM)
-#define SPD_EEPROM_ADDRESS	0x51 /* I2C address of DDR SODIMM SPD */
-#else
-/*
- * Manually set up DDR parameters
- * WHITE ELECTRONIC DESIGNS - W3HG64M72EEU403PD4 SO-DIMM
- * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5
- */
-#define CONFIG_SYS_DDR_SIZE		512 /* MB */
-#define CONFIG_SYS_DDR_CS0_BNDS	0x0000001f
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
-			| CSCONFIG_ODT_RD_NEVER  /* ODT_RD to none */ \
-			| CSCONFIG_ODT_WR_ONLY_CURRENT  /* ODT_WR to CSn */ \
-			| CSCONFIG_ROW_BIT_14 \
-			| CSCONFIG_COL_BIT_10)
-			/* 0x80010202 */
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-#define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
-				| (0 << TIMING_CFG0_WRT_SHIFT) \
-				| (0 << TIMING_CFG0_RRT_SHIFT) \
-				| (0 << TIMING_CFG0_WWT_SHIFT) \
-				| (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
-				| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
-				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
-				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
-				/* 0x00620802 */
-#define CONFIG_SYS_DDR_TIMING_1	((3 << TIMING_CFG1_PRETOACT_SHIFT) \
-				| (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
-				| (3 << TIMING_CFG1_ACTTORW_SHIFT) \
-				| (5 << TIMING_CFG1_CASLAT_SHIFT) \
-				| (13 << TIMING_CFG1_REFREC_SHIFT) \
-				| (3 << TIMING_CFG1_WRREC_SHIFT) \
-				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
-				| (2 << TIMING_CFG1_WRTORD_SHIFT))
-				/* 0x3935d322 */
-#define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
-				| (6 << TIMING_CFG2_CPO_SHIFT) \
-				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
-				| (4 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
-				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
-				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
-				| (8 << TIMING_CFG2_FOUR_ACT_SHIFT))
-				/* 0x131088c8 */
-#define CONFIG_SYS_DDR_INTERVAL	((0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT) \
-				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
-				/* 0x03E00100 */
-#define CONFIG_SYS_DDR_SDRAM_CFG	0x43000000
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00001000 /* 1 posted refresh */
-#define CONFIG_SYS_DDR_MODE	((0x0448 << SDRAM_MODE_ESD_SHIFT) \
-				| (0x1432 << SDRAM_MODE_SD_SHIFT))
-				/* ODT 150ohm CL=3, AL=1 on SDRAM */
-#define CONFIG_SYS_DDR_MODE2	0x00000000
-#endif
-
-/*
- * Memory test
- */
-#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CONFIG_SYS_MONITOR_LEN	(512 * 1024) /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	\
-			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_BASE	0xFE000000 /* FLASH base address */
-#define CONFIG_SYS_FLASH_SIZE	32 /* max FLASH size is 32M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	256 /* max sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
-
-/*
- * BCSR on the Local Bus
- */
-#define CONFIG_SYS_BCSR		0xF8000000
-					/* Access window base at BCSR base */
-
-/*
- * NAND Flash on the Local Bus
- */
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_NAND_FSL_ELBC	1
-
-#define CONFIG_SYS_NAND_BASE	0xE0600000
-
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x51} }
-
-/*
- * Config on-board RTC
- */
-#define CONFIG_RTC_DS1374	/* use ds1374 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68 /* at address 0x68 */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI_MEM_BASE		0x80000000
-#define CONFIG_SYS_PCI_MEM_PHYS		CONFIG_SYS_PCI_MEM_BASE
-#define CONFIG_SYS_PCI_MEM_SIZE		0x10000000 /* 256M */
-#define CONFIG_SYS_PCI_MMIO_BASE	0x90000000
-#define CONFIG_SYS_PCI_MMIO_PHYS	CONFIG_SYS_PCI_MMIO_BASE
-#define CONFIG_SYS_PCI_MMIO_SIZE	0x10000000 /* 256M */
-#define CONFIG_SYS_PCI_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI_IO_PHYS		0xE0300000
-#define CONFIG_SYS_PCI_IO_SIZE		0x100000 /* 1M */
-
-#define CONFIG_SYS_PCI_SLV_MEM_LOCAL	CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_PCI_SLV_MEM_BUS	0x00000000
-#define CONFIG_SYS_PCI_SLV_MEM_SIZE	0x80000000
-
-#define CONFIG_SYS_PCIE1_BASE		0xA0000000
-#define CONFIG_SYS_PCIE1_CFG_BASE	0xA0000000
-#define CONFIG_SYS_PCIE1_CFG_SIZE	0x08000000
-#define CONFIG_SYS_PCIE1_MEM_BASE	0xA8000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xA8000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
-#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xB8000000
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
-
-#define CONFIG_SYS_PCIE2_BASE		0xC0000000
-#define CONFIG_SYS_PCIE2_CFG_BASE	0xC0000000
-#define CONFIG_SYS_PCIE2_CFG_SIZE	0x08000000
-#define CONFIG_SYS_PCIE2_MEM_BASE	0xC8000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xC8000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000
-#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xD8000000
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#ifndef __ASSEMBLY__
-extern int board_pci_host_broken(void);
-#endif
-#define CONFIG_PCIE
-#define CONFIG_PQ_MDS_PIB	1 /* PQ MDS Platform IO Board */
-
-#define CONFIG_HAS_FSL_DR_USB	1 /* fixup device tree for the DR USB */
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-
-#undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
-#endif /* CONFIG_PCI */
-
-/*
- * TSEC
- */
-#define CONFIG_SYS_TSEC1_OFFSET	0x24000
-#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET	0x25000
-#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/*
- * TSEC ethernet configuration
- */
-#define CONFIG_TSEC1		1
-#define CONFIG_TSEC1_NAME	"eTSEC0"
-#define CONFIG_TSEC2		1
-#define CONFIG_TSEC2_NAME	"eTSEC1"
-#define TSEC1_PHY_ADDR		2
-#define TSEC2_PHY_ADDR		3
-#define TSEC1_PHY_ADDR_SGMII	8
-#define TSEC2_PHY_ADDR_SGMII	4
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME		"eTSEC1"
-
-/* SERDES */
-#define CONFIG_FSL_SERDES
-#define CONFIG_FSL_SERDES1	0xe3000
-#define CONFIG_FSL_SERDES2	0xe3100
-
-/*
- * SATA
- */
-#define CONFIG_SYS_SATA_MAX_DEVICE	2
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1_OFFSET	0x18000
-#define CONFIG_SYS_SATA1	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
-#define CONFIG_SYS_SATA1_FLAGS	FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2_OFFSET	0x19000
-#define CONFIG_SYS_SATA2	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
-#define CONFIG_SYS_SATA2_FLAGS	FLAGS_DMA
-
-#ifdef CONFIG_FSL_SATA
-#define CONFIG_LBA48
-#endif
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG		/* watchdog disabled */
-
-#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC_PIN_MUX
-#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC83xx_ESDHC_ADDR
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-#define CONFIG_LOADADDR 800000	/* default location for tftp and bootm */
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"consoledev=ttyS0\0"						\
-	"ramdiskaddr=1000000\0"						\
-	"ramdiskfile=ramfs.83xx\0"					\
-	"fdtaddr=780000\0"						\
-	"fdtfile=mpc8379_mds.dtb\0"					\
-	""
-
-#define CONFIG_NFSBOOTCOMMAND						\
-	"setenv bootargs root=/dev/nfs rw "				\
-		"nfsroot=$serverip:$rootpath "				\
-		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
-							"$netdev:off "	\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND						\
-	"setenv bootargs root=/dev/ram rw "				\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $ramdiskaddr $ramdiskfile;"				\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif	/* __CONFIG_H */