Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  ARM: Add Calxeda Highbank platform
  dkb: make mmc command as default enabled
  Marvell: dkb: add mmc support
  ARM: pantheon: add mmc definition
  davinci: remove config.mk file from the sources
  ARM:AM33XX: Add support for TI AM335X EVM
  ARM:AM33XX: Added timer support
  ARM:AM33XX: Add emif/ddr support
  ARM:AM33XX: Add clock definitions
  ARM:AM33XX: Added support for AM33xx
  omap3/emif4: fix registers definition
  davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
  davinci: emac: add support for more than 1 PHYs
  davinci: emac: add new features to autonegotiate for EMAC
  da850evm: Move LPSC configuration to board_early_init_f()
  omap4_panda: Build in cmd_gpio support on panda
  omap: Don't use gpio_free to change direction to input
  mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
  OMAP3: overo : Add environment variable optargs to bootargs
  OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
  OMAP3: overo : Use ttyO2 instead of ttyS2.
  da830: add support for NAND boot mode
  dm36x: revert cache disable patch
  dm644X: revert cache disable patch
  devkit8000: Add malloc space
  omap: spl: fix build break due to changes in FAT
  OMAP3 SPL: Provide weak omap_rev_string
  omap: beagle: Use ubifs instead of jffs2 for nand boot
  omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
  omap: overo: Configure mux for gpio10
  SPL: Add DMA library
  omap3: Add interface for omap3 DMA
  omap3: Add DMA register accessors
  omap3: Add Base register for DMA
  arm, davinci: add missing LSPC define for MMC/SD1
  U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
  DaVinci: correct MDSTAT.STATE mask
  omap4: splitting padconfs into common, 4430 and 4460
  omap4: adding revision detection for 4460 ES1.1
  omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
  gplug: fixed build error as a result of code cleanup patch
  kirkwood_spi: add dummy spi_init()
  gpio: mvmfp: reduce include platform file
  ARM: orion5x: reduce dependence of including platform file
  serial: reduce include platform file for marvell chip
  ARM: kirkwood: reduce dependence of including platform file
  ARM: armada100: reduce dependence of including platform file
  ARM: pantheon: reduce dependence of including platform file
  Armada100: Add env storage support for Marvell gplugD
  Armada100: Add SPI flash support for Marvell gplugD
  Armada100: Add SPI support for Marvell gplugD
  SPI: Add SPI driver support for Marvell Armada100
  dreamplug: initial board support.
  imx: fix coding style
  misc: pmic: drop old Freescale's pmic driver
  MX31: mx31pdk: use new pmic driver
  MX31: mx31ads: use new pmic driver
  MX31: mx31_litekit: use new pmic driver
  MX5: mx53evk: use new pmic driver
  MX5: mx51evk: use new pmic driver
  MX35: mx35pdk: use new pmic driver
  misc: pmic: addI2C  support to pmic_fsl driver
  misc: pmic: use I2C_SET_BUS in pmic I2C
  MX5: efikamx/efikasb: use new pmic driver
  MX3: qong: use new pmic driver
  RTC: Switch mc13783 to generic pmic code
  MX5: vision2: use new pmic driver
  misc: pmic: Freescale PMIC switches to generic PMIC driver
  misc:pmic:samsung Enable PMIC driver at GONI target
  misc:pmic:max8998 MAX8998 support at a new PMIC driver.
  misc:pmic:core New generic PMIC driver
  mx31pdk: Remove unneeded config
  mx31: provide readable WEIM CS accessor
  MX51: vision2: Set global macros
  I2C: Add i2c_get/set_speed() to mxc_i2c.c
  ARM: Update mach-types
  devkit8000: Add config to enable SPL MMC boot
  devkit8000: protect board_mmc_init
  arm, post: add missing post_time_ms for arm
  cosmetic, post: Codingstyle cleanup
  arm, logbuffer: make it compileclean
  tegra2: Enable MMC for Seaboard
  tegra2: Add more pinmux functions
  tegra2: Rename PIN_ to PINGRP_
  tegra2: Add more clock functions
  tegra2: Clean up board code a little
  tegra2: Rename CLOCK_PLL_ID to CLOCK_ID

5 files changed, 72 insertions, 40 deletions

diff --git a/board/freescale/mx31ads/mx31ads.c b/board/freescale/mx31ads/mx31ads.c
index 4dd1e63a83..1def0d9284 100644
--- a/board/freescale/mx31ads/mx31ads.c
+++ b/board/freescale/mx31ads/mx31ads.c
@@ -25,6 +25,7 @@
 #include <asm/io.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -48,9 +49,16 @@ int board_early_init_f(void)
 	 * the only non-zero field "Wait State Control" is set to half the
 	 * default value.
 	 */
-	__REG(CSCR_U(0)) = 0x00000f00;
-	__REG(CSCR_L(0)) = 0x10000D03;
-	__REG(CSCR_A(0)) = 0x00720900;
+	static const struct mxc_weimcs cs0 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  0, 15, 0,  0,  0),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(1,  0,   0,   0,  0,  1,  5,  0,  0,  0,   1,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(0,   0,  7,  2,  0,  0,  2,  1,  0,  0,  0,  0,   0,   0)
+	};
+
+	mxc_setup_weimcs(0, &cs0);
 
 	/* setup pins for UART1 */
 	mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
@@ -104,7 +112,7 @@ int board_init(void)
 	return 0;
 }
 
-int checkboard (void)
+int checkboard(void)
 {
 	printf("Board: MX31ADS\n");
 	return 0;
diff --git a/board/freescale/mx31pdk/mx31pdk.c b/board/freescale/mx31pdk/mx31pdk.c
index 276d45153a..0e7e0ce347 100644
--- a/board/freescale/mx31pdk/mx31pdk.c
+++ b/board/freescale/mx31pdk/mx31pdk.c
@@ -28,6 +28,7 @@
 #include <netdev.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
 #include <watchdog.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -50,9 +51,16 @@ int dram_init(void)
 int board_early_init_f(void)
 {
 	/* CS5: CPLD incl. network controller */
-	__REG(CSCR_U(5)) = 0x0000d843;
-	__REG(CSCR_L(5)) = 0x22252521;
-	__REG(CSCR_A(5)) = 0x22220a00;
+	static const struct mxc_weimcs cs5 = {
+		/*    sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
+		CSCR_U(0, 0,  0,  0,  0,  0,   0,  0,  3, 24, 0,  4,  3),
+		/*   oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
+		CSCR_L(2,  2,   2,   5,  2,  0,  5,  2,  0,  0,   0,   1),
+		/*  ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
+		CSCR_A(2,   2,  2,  2,  0,  0,  2,  2,  0,  0,  0,  0,   0,  0)
+	};
+
+	mxc_setup_weimcs(5, &cs5);
 
 	/* Setup UART1 and SPI2 pins */
 	mx31_uart1_hw_init();
diff --git a/board/freescale/mx35pdk/mx35pdk.c b/board/freescale/mx35pdk/mx35pdk.c
index 2ce6e8e340..a5b51a0aa0 100644
--- a/board/freescale/mx35pdk/mx35pdk.c
+++ b/board/freescale/mx35pdk/mx35pdk.c
@@ -30,6 +30,7 @@
 #include <asm/arch/mx35_pins.h>
 #include <asm/arch/iomux.h>
 #include <i2c.h>
+#include <pmic.h>
 #include <fsl_pmic.h>
 #include <mc9sdz60.h>
 #include <mc13892.h>
@@ -202,9 +203,10 @@ int board_init(void)
 
 static inline int pmic_detect(void)
 {
-	int id;
+	unsigned int id;
+	struct pmic *p = get_pmic();
 
-	id = pmic_reg_read(REG_IDENTIFICATION);
+	pmic_reg_read(p, REG_IDENTIFICATION, &id);
 
 	id = (id >> 6) & 0x7;
 	if (id == 0x7)
@@ -225,15 +227,19 @@ int board_late_init(void)
 {
 	u8 val;
 	u32 pmic_val;
+	struct pmic *p;
 
+	pmic_init();
 	if (pmic_detect()) {
+		p = get_pmic();
 		mxc_request_iomux(MX35_PIN_WATCHDOG_RST, MUX_CONFIG_SION |
 					MUX_CONFIG_ALT1);
 
-		pmic_val = pmic_reg_read(REG_SETTING_0);
-		pmic_reg_write(REG_SETTING_0, pmic_val | VO_1_30V | VO_1_50V);
-		pmic_val = pmic_reg_read(REG_MODE_0);
-		pmic_reg_write(REG_MODE_0, pmic_val | VGEN3EN);
+		pmic_reg_read(p, REG_SETTING_0, &pmic_val);
+		pmic_reg_write(p, REG_SETTING_0,
+			pmic_val | VO_1_30V | VO_1_50V);
+		pmic_reg_read(p, REG_MODE_0, &pmic_val);
+		pmic_reg_write(p, REG_MODE_0, pmic_val | VGEN3EN);
 
 		mxc_request_iomux(MX35_PIN_COMPARE, MUX_CONFIG_GPIO);
 		mxc_iomux_set_input(MUX_IN_GPIO1_IN_5, INPUT_CTL_PATH0);
diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c
index f998610577..2a0dad021e 100644
--- a/board/freescale/mx51evk/mx51evk.c
+++ b/board/freescale/mx51evk/mx51evk.c
@@ -32,6 +32,7 @@
 #include <i2c.h>
 #include <mmc.h>
 #include <fsl_esdhc.h>
+#include <pmic.h>
 #include <fsl_pmic.h>
 #include <mc13892.h>
 
@@ -182,34 +183,38 @@ static void power_init(void)
 {
 	unsigned int val;
 	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)MXC_CCM_BASE;
+	struct pmic *p;
+
+	pmic_init();
+	p = get_pmic();
 
 	/* Write needed to Power Gate 2 register */
-	val = pmic_reg_read(REG_POWER_MISC);
+	pmic_reg_read(p, REG_POWER_MISC, &val);
 	val &= ~PWGT2SPIEN;
-	pmic_reg_write(REG_POWER_MISC, val);
+	pmic_reg_write(p, REG_POWER_MISC, val);
 
 	/* Externally powered */
-	val = pmic_reg_read(REG_CHARGE);
+	pmic_reg_read(p, REG_CHARGE, &val);
 	val |= ICHRG0 | ICHRG1 | ICHRG2 | ICHRG3 | CHGAUTOB;
-	pmic_reg_write(REG_CHARGE, val);
+	pmic_reg_write(p, REG_CHARGE, val);
 
 	/* power up the system first */
-	pmic_reg_write(REG_POWER_MISC, PWUP);
+	pmic_reg_write(p, REG_POWER_MISC, PWUP);
 
 	/* Set core voltage to 1.1V */
-	val = pmic_reg_read(REG_SW_0);
+	pmic_reg_read(p, REG_SW_0, &val);
 	val = (val & ~SWx_VOLT_MASK) | SWx_1_100V;
-	pmic_reg_write(REG_SW_0, val);
+	pmic_reg_write(p, REG_SW_0, val);
 
 	/* Setup VCC (SW2) to 1.25 */
-	val = pmic_reg_read(REG_SW_1);
+	pmic_reg_read(p, REG_SW_1, &val);
 	val = (val & ~SWx_VOLT_MASK) | SWx_1_250V;
-	pmic_reg_write(REG_SW_1, val);
+	pmic_reg_write(p, REG_SW_1, val);
 
 	/* Setup 1V2_DIG1 (SW3) to 1.25 */
-	val = pmic_reg_read(REG_SW_2);
+	pmic_reg_read(p, REG_SW_2, &val);
 	val = (val & ~SWx_VOLT_MASK) | SWx_1_250V;
-	pmic_reg_write(REG_SW_2, val);
+	pmic_reg_write(p, REG_SW_2, val);
 	udelay(50);
 
 	/* Raise the core frequency to 800MHz */
@@ -217,36 +222,36 @@ static void power_init(void)
 
 	/* Set switchers in Auto in NORMAL mode & STANDBY mode */
 	/* Setup the switcher mode for SW1 & SW2*/
-	val = pmic_reg_read(REG_SW_4);
+	pmic_reg_read(p, REG_SW_4, &val);
 	val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) |
 		(SWMODE_MASK << SWMODE2_SHIFT)));
 	val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) |
 		(SWMODE_AUTO_AUTO << SWMODE2_SHIFT);
-	pmic_reg_write(REG_SW_4, val);
+	pmic_reg_write(p, REG_SW_4, val);
 
 	/* Setup the switcher mode for SW3 & SW4 */
-	val = pmic_reg_read(REG_SW_5);
+	pmic_reg_read(p, REG_SW_5, &val);
 	val = (val & ~((SWMODE_MASK << SWMODE3_SHIFT) |
 		(SWMODE_MASK << SWMODE4_SHIFT)));
 	val |= (SWMODE_AUTO_AUTO << SWMODE3_SHIFT) |
 		(SWMODE_AUTO_AUTO << SWMODE4_SHIFT);
-	pmic_reg_write(REG_SW_5, val);
+	pmic_reg_write(p, REG_SW_5, val);
 
 	/* Set VDIG to 1.65V, VGEN3 to 1.8V, VCAM to 2.6V */
-	val = pmic_reg_read(REG_SETTING_0);
+	pmic_reg_read(p, REG_SETTING_0, &val);
 	val &= ~(VCAM_MASK | VGEN3_MASK | VDIG_MASK);
 	val |= VDIG_1_65 | VGEN3_1_8 | VCAM_2_6;
-	pmic_reg_write(REG_SETTING_0, val);
+	pmic_reg_write(p, REG_SETTING_0, val);
 
 	/* Set VVIDEO to 2.775V, VAUDIO to 3V, VSD to 3.15V */
-	val = pmic_reg_read(REG_SETTING_1);
+	pmic_reg_read(p, REG_SETTING_1, &val);
 	val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK);
 	val |= VSD_3_15 | VAUDIO_3_0 | VVIDEO_2_775;
-	pmic_reg_write(REG_SETTING_1, val);
+	pmic_reg_write(p, REG_SETTING_1, val);
 
 	/* Configure VGEN3 and VCAM regulators to use external PNP */
 	val = VGEN3CONFIG | VCAMCONFIG;
-	pmic_reg_write(REG_MODE_1, val);
+	pmic_reg_write(p, REG_MODE_1, val);
 	udelay(200);
 
 	gpio_direction_output(46, 0);
@@ -257,7 +262,7 @@ static void power_init(void)
 	/* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
 	val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG |
 		VVIDEOEN | VAUDIOEN  | VSDEN;
-	pmic_reg_write(REG_MODE_1, val);
+	pmic_reg_write(p, REG_MODE_1, val);
 
 	udelay(500);
 
diff --git a/board/freescale/mx53evk/mx53evk.c b/board/freescale/mx53evk/mx53evk.c
index fd821c0b1d..eab9c5f7d4 100644
--- a/board/freescale/mx53evk/mx53evk.c
+++ b/board/freescale/mx53evk/mx53evk.c
@@ -32,6 +32,7 @@
 #include <i2c.h>
 #include <mmc.h>
 #include <fsl_esdhc.h>
+#include <pmic.h>
 #include <fsl_pmic.h>
 #include <asm/gpio.h>
 #include <mc13892.h>
@@ -124,12 +125,16 @@ static void setup_i2c(unsigned int port_number)
 void power_init(void)
 {
 	unsigned int val;
+	struct pmic *p;
+
+	pmic_init();
+	p = get_pmic();
 
 	/* Set VDDA to 1.25V */
-	val = pmic_reg_read(REG_SW_2);
+	pmic_reg_read(p, REG_SW_2, &val);
 	val &= ~SWX_OUT_MASK;
 	val |= SWX_OUT_1_25;
-	pmic_reg_write(REG_SW_2, val);
+	pmic_reg_write(p, REG_SW_2, val);
 
 	/*
 	 * Need increase VCC and VDDA to 1.3V
@@ -137,16 +142,16 @@ void power_init(void)
 	 */
 	if (is_soc_rev(CHIP_REV_2_0) == 0) {
 		/* Set VCC to 1.3V for TO2 */
-		val = pmic_reg_read(REG_SW_1);
+		pmic_reg_read(p, REG_SW_1, &val);
 		val &= ~SWX_OUT_MASK;
 		val |= SWX_OUT_1_30;
-		pmic_reg_write(REG_SW_1, val);
+		pmic_reg_write(p, REG_SW_1, val);
 
 		/* Set VDDA to 1.3V for TO2 */
-		val = pmic_reg_read(REG_SW_2);
+		pmic_reg_read(p, REG_SW_2, &val);
 		val &= ~SWX_OUT_MASK;
 		val |= SWX_OUT_1_30;
-		pmic_reg_write(REG_SW_2, val);
+		pmic_reg_write(p, REG_SW_2, val);
 	}
 }