ppc: Remove TQM834x board

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.

Signed-off-by: Tom Rini <trini@konsulko.com>

8 files changed, 0 insertions, 1007 deletions

diff --git a/arch/powerpc/cpu/mpc83xx/Kconfig b/arch/powerpc/cpu/mpc83xx/Kconfig
index e751daac6e..a67216a2f4 100644
--- a/arch/powerpc/cpu/mpc83xx/Kconfig
+++ b/arch/powerpc/cpu/mpc83xx/Kconfig
@@ -89,11 +89,6 @@ config TARGET_KMTEPR2
 	select VENDOR_KM
 	select KM_ENABLE_FULL_DM_DTS_SUPPORT
 
-config TARGET_TQM834X
-	bool "Support TQM834x"
-	select ARCH_MPC8349
-
-
 config TARGET_GAZERBEAM
 	bool "Support gazerbeam"
 	select ARCH_MPC8308
@@ -277,7 +272,6 @@ source "board/freescale/mpc8349emds/Kconfig"
 source "board/freescale/mpc837xerdb/Kconfig"
 source "board/ids/ids8313/Kconfig"
 source "board/keymile/Kconfig"
-source "board/tqc/tqm834x/Kconfig"
 source "board/gdsys/mpc8308/Kconfig"
 
 endmenu
diff --git a/board/tqc/tqm834x/Kconfig b/board/tqc/tqm834x/Kconfig
deleted file mode 100644
index 028b8466e8..0000000000
--- a/board/tqc/tqm834x/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_TQM834X
-
-config SYS_BOARD
-	default "tqm834x"
-
-config SYS_VENDOR
-	default "tqc"
-
-config SYS_CONFIG_NAME
-	default "TQM834x"
-
-endif
diff --git a/board/tqc/tqm834x/MAINTAINERS b/board/tqc/tqm834x/MAINTAINERS
deleted file mode 100644
index 543ab1b552..0000000000
--- a/board/tqc/tqm834x/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-TQM834X BOARD
-#M:	-
-S:	Maintained
-F:	board/tqc/tqm834x/
-F:	include/configs/TQM834x.h
-F:	configs/TQM834x_defconfig
diff --git a/board/tqc/tqm834x/Makefile b/board/tqc/tqm834x/Makefile
deleted file mode 100644
index 3aafbf7928..0000000000
--- a/board/tqc/tqm834x/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright 2004 Freescale Semiconductor, Inc.
-
-obj-y += tqm834x.o
-obj-$(CONFIG_PCI) += pci.o
diff --git a/board/tqc/tqm834x/pci.c b/board/tqc/tqm834x/pci.c
deleted file mode 100644
index 92bda60765..0000000000
--- a/board/tqc/tqm834x/pci.c
+++ /dev/null
@@ -1,98 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- * Copyright (C) 2006-2009 Freescale Semiconductor, Inc.
- */
-
-#include <init.h>
-#include <asm/mmu.h>
-#include <asm/io.h>
-#include <common.h>
-#include <mpc83xx.h>
-#include <pci.h>
-#include <i2c.h>
-#include <asm/fsl_i2c.h>
-#include <linux/delay.h>
-
-static struct pci_region pci1_regions[] = {
-	{
-		bus_start: CONFIG_SYS_PCI1_MEM_BASE,
-		phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
-		size: CONFIG_SYS_PCI1_MEM_SIZE,
-		flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
-	},
-	{
-		bus_start: CONFIG_SYS_PCI1_IO_BASE,
-		phys_start: CONFIG_SYS_PCI1_IO_PHYS,
-		size: CONFIG_SYS_PCI1_IO_SIZE,
-		flags: PCI_REGION_IO
-	},
-	{
-		bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
-		phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
-		size: CONFIG_SYS_PCI1_MMIO_SIZE,
-		flags: PCI_REGION_MEM
-	},
-};
-
-/*
- * pci_init_board()
- *
- * NOTICE: MPC8349 internally has two PCI controllers (PCI1 and PCI2) but since
- * per TQM834x design physical connections to external devices (PCI sockets)
- * are routed only to the PCI1 we do not account for the second one - this code
- * supports PCI1 module only. Should support for the PCI2 be required in the
- * future it needs a separate pci_controller structure (above) and handling -
- * please refer to other boards' implementation for dual PCI host controllers,
- * for example board/Marvell/db64360/pci.c, pci_init_board()
- *
- */
-void
-pci_init_board(void)
-{
-	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
-	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
-	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
-	struct pci_region *reg[] = { pci1_regions };
-	u32 reg32;
-
-	/*
-	 * Configure PCI controller and PCI_CLK_OUTPUT
-	 *
-	 * WARNING! only PCI_CLK_OUTPUT1 is enabled here as this is the one
-	 * line actually used for clocking all external PCI devices in TQM83xx.
-	 * Enabling other PCI_CLK_OUTPUT lines may lead to board's hang for
-	 * unknown reasons - particularly PCI_CLK_OUTPUT6 and PCI_CLK_OUTPUT7
-	 * are known to hang the board; this issue is under investigation
-	 * (13 oct 05)
-	 */
-	reg32 = OCCR_PCICOE1;
-#if 0
-	/* enabling all PCI_CLK_OUTPUT lines HANGS the board... */
-	reg32 = 0xff000000;
-#endif
-	if (clk->spmr & SPMR_CKID) {
-		/* PCI Clock is half CONFIG_SYS_CLK_FREQ so need to set up OCCR
-		 * fields accordingly */
-		reg32 |= (OCCR_PCI1CR | OCCR_PCI2CR);
-
-		reg32 |= (OCCR_PCICD0 | OCCR_PCICD1 | OCCR_PCICD2 \
-			  | OCCR_PCICD3 | OCCR_PCICD4 | OCCR_PCICD5 \
-			  | OCCR_PCICD6 | OCCR_PCICD7);
-	}
-
-	clk->occr = reg32;
-	udelay(2000);
-
-	/* Configure PCI Local Access Windows */
-	pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
-	pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_512M;
-
-	pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
-	pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_16M;
-
-	udelay(2000);
-
-	mpc83xx_pci_init(1, reg);
-}
diff --git a/board/tqc/tqm834x/tqm834x.c b/board/tqc/tqm834x/tqm834x.c
deleted file mode 100644
index 17b4662c16..0000000000
--- a/board/tqc/tqm834x/tqm834x.c
+++ /dev/null
@@ -1,433 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#include <common.h>
-#include <fdt_support.h>
-#include <init.h>
-#include <ioports.h>
-#include <log.h>
-#include <mpc83xx.h>
-#include <asm/global_data.h>
-#include <asm/mpc8349_pci.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <asm/mmu.h>
-#include <pci.h>
-#include <flash.h>
-#include <linux/delay.h>
-#include <mtd/cfi_flash.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define IOSYNC			asm("eieio")
-#define ISYNC			asm("isync")
-#define SYNC			asm("sync")
-#define FPW			FLASH_PORT_WIDTH
-#define FPWV			FLASH_PORT_WIDTHV
-
-#define DDR_MAX_SIZE_PER_CS	0x20000000
-
-#if defined(DDR_CASLAT_20)
-#define TIMING_CASLAT		TIMING_CFG1_CASLAT_20
-#define MODE_CASLAT		DDR_MODE_CASLAT_20
-#else
-#define TIMING_CASLAT		TIMING_CFG1_CASLAT_25
-#define MODE_CASLAT		DDR_MODE_CASLAT_25
-#endif
-
-#define INITIAL_CS_CONFIG	(CSCONFIG_EN | CSCONFIG_ROW_BIT_12 | \
-				CSCONFIG_COL_BIT_9)
-
-/* External definitions */
-ulong flash_get_size (ulong base, int banknum);
-
-/* Local functions */
-static int detect_num_flash_banks(void);
-static long int get_ddr_bank_size(short cs, long *base);
-static void set_cs_bounds(short cs, ulong base, ulong size);
-static void set_cs_config(short cs, long config);
-static void set_ddr_config(void);
-
-/* Local variable */
-static volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
-
-/**************************************************************************
- * Board initialzation after relocation to RAM. Used to detect the number
- * of Flash banks on TQM834x.
- */
-int board_early_init_r (void) {
-	/* sanity check, IMMARBAR should be mirrored at offset zero of IMMR */
-	if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
-		return 0;
-
-	/* detect the number of Flash banks */
-	return detect_num_flash_banks();
-}
-
-/**************************************************************************
- * DRAM initalization and size detection
- */
-int dram_init(void)
-{
-	long bank_size;
-	long size;
-	int cs;
-
-	/* during size detection, set up the max DDRLAW size */
-	im->sysconf.ddrlaw[0].bar = CONFIG_SYS_SDRAM_BASE;
-	im->sysconf.ddrlaw[0].ar = (LAWAR_EN | LAWAR_SIZE_2G);
-
-	/* set CS bounds to maximum size */
-	for(cs = 0; cs < 4; ++cs) {
-		set_cs_bounds(cs,
-			CONFIG_SYS_SDRAM_BASE + (cs * DDR_MAX_SIZE_PER_CS),
-			DDR_MAX_SIZE_PER_CS);
-
-		set_cs_config(cs, INITIAL_CS_CONFIG);
-	}
-
-	/* configure ddr controller */
-	set_ddr_config();
-
-	udelay(200);
-
-	/* enable DDR controller */
-	im->ddr.sdram_cfg = (SDRAM_CFG_MEM_EN |
-		SDRAM_CFG_SREN |
-		SDRAM_CFG_SDRAM_TYPE_DDR1);
-	SYNC;
-
-	/* size detection */
-	debug("\n");
-	size = 0;
-	for(cs = 0; cs < 4; ++cs) {
-		debug("\nDetecting Bank%d\n", cs);
-
-		bank_size = get_ddr_bank_size(cs,
-			(long *)(CONFIG_SYS_SDRAM_BASE + size));
-		size += bank_size;
-
-		debug("DDR Bank%d size: %ld MiB\n\n", cs, bank_size >> 20);
-
-		/* exit if less than one bank */
-		if(size < DDR_MAX_SIZE_PER_CS) break;
-	}
-
-	gd->ram_size = size;
-
-	return 0;
-}
-
-/**************************************************************************
- * checkboard()
- */
-int checkboard (void)
-{
-	puts("Board: TQM834x\n");
-
-#ifdef CONFIG_PCI
-	volatile immap_t * immr;
-	u32 w, f;
-
-	immr = (immap_t *)CONFIG_SYS_IMMR;
-	if (!(immr->reset.rcwh & HRCWH_PCI_HOST)) {
-		printf("PCI:   NOT in host mode..?!\n");
-		return 0;
-	}
-
-	/* get bus width */
-	w = 32;
-	if (immr->reset.rcwh & HRCWH_64_BIT_PCI)
-		w = 64;
-
-	/* get clock */
-	f = gd->pci_clk;
-
-	printf("PCI1:  %d bit, %d MHz\n", w, f / 1000000);
-#else
-	printf("PCI:   disabled\n");
-#endif
-	return 0;
-}
-
-
-/**************************************************************************
- *
- * Local functions
- *
- *************************************************************************/
-
-/**************************************************************************
- * Detect the number of flash banks (1 or 2). Store it in
- * a global variable tqm834x_num_flash_banks.
- * Bank detection code based on the Monitor code.
- */
-static int detect_num_flash_banks(void)
-{
-	typedef unsigned long FLASH_PORT_WIDTH;
-	typedef volatile unsigned long FLASH_PORT_WIDTHV;
-	FPWV *bank1_base;
-	FPWV *bank2_base;
-	FPW bank1_read;
-	FPW bank2_read;
-	ulong bank1_size;
-	ulong bank2_size;
-	ulong total_size;
-
-	cfi_flash_num_flash_banks = 2;	/* assume two banks */
-
-	/* Get bank 1 and 2 information */
-	bank1_size = flash_get_size(CONFIG_SYS_FLASH_BASE, 0);
-	debug("Bank1 size: %lu\n", bank1_size);
-	bank2_size = flash_get_size(CONFIG_SYS_FLASH_BASE + bank1_size, 1);
-	debug("Bank2 size: %lu\n", bank2_size);
-	total_size = bank1_size + bank2_size;
-
-	if (bank2_size > 0) {
-		/* Seems like we've got bank 2, but maybe it's mirrored 1 */
-
-		/* Set the base addresses */
-		bank1_base = (FPWV *) (CONFIG_SYS_FLASH_BASE);
-		bank2_base = (FPWV *) (CONFIG_SYS_FLASH_BASE + bank1_size);
-
-		/* Put bank 2 into CFI command mode and read */
-		bank2_base[0x55] = 0x00980098;
-		IOSYNC;
-		ISYNC;
-		bank2_read = bank2_base[0x10];
-
-		/* Read from bank 1 (it's in read mode) */
-		bank1_read = bank1_base[0x10];
-
-		/* Reset Flash */
-		bank1_base[0] = 0x00F000F0;
-		bank2_base[0] = 0x00F000F0;
-
-		if (bank2_read == bank1_read) {
-			/*
-			 * Looks like just one bank, but not sure yet. Let's
-			 * read from bank 2 in autosoelect mode.
-			 */
-			bank2_base[0x0555] = 0x00AA00AA;
-			bank2_base[0x02AA] = 0x00550055;
-			bank2_base[0x0555] = 0x00900090;
-			IOSYNC;
-			ISYNC;
-			bank2_read = bank2_base[0x10];
-
-			/* Read from bank 1 (it's in read mode) */
-			bank1_read = bank1_base[0x10];
-
-			/* Reset Flash */
-			bank1_base[0] = 0x00F000F0;
-			bank2_base[0] = 0x00F000F0;
-
-			if (bank2_read == bank1_read) {
-				/*
-				 * In both CFI command and autoselect modes,
-				 * we got the some data reading from Flash.
-				 * There is only one mirrored bank.
-				 */
-				cfi_flash_num_flash_banks = 1;
-				total_size = bank1_size;
-			}
-		}
-	}
-
-	debug("Number of flash banks detected: %d\n", cfi_flash_num_flash_banks);
-
-	/* set OR0 and BR0 */
-	set_lbc_or(0, OR_GPCM_CSNT | OR_GPCM_ACS_DIV4 | OR_GPCM_SCY_5 |
-		   OR_GPCM_TRLX | (-(total_size) & OR_GPCM_AM));
-	set_lbc_br(0, (CONFIG_SYS_FLASH_BASE & BR_BA) |
-		   (BR_MS_GPCM | BR_PS_32 | BR_V));
-
-	return (0);
-}
-
-/*************************************************************************
- * Detect the size of a ddr bank. Sets CS bounds and CS config accordingly.
- */
-static long int get_ddr_bank_size(short cs, long *base)
-{
-	/* This array lists all valid DDR SDRAM configurations, with
-	 * Bank sizes in bytes. (Refer to Table 9-27 in the MPC8349E RM).
-	 * The last entry has to to have size equal 0 and is igonred during
-	 * autodection. Bank sizes must be in increasing order of size
-	 */
-	struct {
-		long row;
-		long col;
-		long size;
-	} conf[] = {
-		{CSCONFIG_ROW_BIT_12,	CSCONFIG_COL_BIT_8,	32 << 20},
-		{CSCONFIG_ROW_BIT_12,	CSCONFIG_COL_BIT_9,	64 << 20},
-		{CSCONFIG_ROW_BIT_12,	CSCONFIG_COL_BIT_10,	128 << 20},
-		{CSCONFIG_ROW_BIT_13,	CSCONFIG_COL_BIT_9,	128 << 20},
-		{CSCONFIG_ROW_BIT_13,	CSCONFIG_COL_BIT_10,	256 << 20},
-		{CSCONFIG_ROW_BIT_13,	CSCONFIG_COL_BIT_11,	512 << 20},
-		{CSCONFIG_ROW_BIT_14,	CSCONFIG_COL_BIT_10,	512 << 20},
-		{CSCONFIG_ROW_BIT_14,	CSCONFIG_COL_BIT_11,	1024 << 20},
-		{0,			0,			0}
-	};
-
-	int i;
-	int detected;
-	long size;
-
-	detected = -1;
-	for(i = 0; conf[i].size != 0; ++i) {
-
-		/* set sdram bank configuration */
-		set_cs_config(cs, CSCONFIG_EN | conf[i].col | conf[i].row);
-
-		debug("Getting RAM size...\n");
-		size = get_ram_size(base, DDR_MAX_SIZE_PER_CS);
-
-		if((size == conf[i].size) && (i == detected + 1))
-			detected = i;
-
-		debug("Trying %ld x %ld (%ld MiB) at addr %p, detected: %ld MiB\n",
-			conf[i].row,
-			conf[i].col,
-			conf[i].size >> 20,
-			base,
-			size >> 20);
-	}
-
-	if(detected == -1){
-		/* disable empty cs */
-		debug("\nNo valid configurations for CS%d, disabling...\n", cs);
-		set_cs_config(cs, 0);
-		return 0;
-	}
-
-	debug("\nDetected configuration %ld x %ld (%ld MiB) at addr %p\n",
-			conf[detected].row, conf[detected].col, conf[detected].size >> 20, base);
-
-	/* configure cs ro detected params */
-	set_cs_config(cs, CSCONFIG_EN | conf[detected].row |
-			conf[detected].col);
-
-	set_cs_bounds(cs, (long)base, conf[detected].size);
-
-	return(conf[detected].size);
-}
-
-/**************************************************************************
- * Sets DDR bank CS bounds.
- */
-static void set_cs_bounds(short cs, ulong base, ulong size)
-{
-	debug("Setting bounds %08lx, %08lx for cs %d\n", base, size, cs);
-	if(size == 0){
-		im->ddr.csbnds[cs].csbnds = 0x00000000;
-	} else {
-		im->ddr.csbnds[cs].csbnds =
-			((base >> CSBNDS_SA_SHIFT) & CSBNDS_SA) |
-			(((base + size - 1) >> CSBNDS_EA_SHIFT) &
-				CSBNDS_EA);
-	}
-	SYNC;
-}
-
-/**************************************************************************
- * Sets DDR banks CS configuration.
- * config == 0x00000000 disables the CS.
- */
-static void set_cs_config(short cs, long config)
-{
-	debug("Setting config %08lx for cs %d\n", config, cs);
-	im->ddr.cs_config[cs] = config;
-	SYNC;
-}
-
-/**************************************************************************
- * Sets DDR clocks, timings and configuration.
- */
-static void set_ddr_config(void) {
-	/* clock control */
-	im->ddr.sdram_clk_cntl = DDR_SDRAM_CLK_CNTL_SS_EN |
-		DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05;
-	SYNC;
-
-	/* timing configuration */
-	im->ddr.timing_cfg_1 =
-		(4 << TIMING_CFG1_PRETOACT_SHIFT) |
-		(7 << TIMING_CFG1_ACTTOPRE_SHIFT) |
-		(4 << TIMING_CFG1_ACTTORW_SHIFT)  |
-		(5 << TIMING_CFG1_REFREC_SHIFT)   |
-		(3 << TIMING_CFG1_WRREC_SHIFT)    |
-		(3 << TIMING_CFG1_ACTTOACT_SHIFT) |
-		(1 << TIMING_CFG1_WRTORD_SHIFT)   |
-		(TIMING_CFG1_CASLAT & TIMING_CASLAT);
-
-	im->ddr.timing_cfg_2 =
-		TIMING_CFG2_CPO_DEF |
-		(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT);
-	SYNC;
-
-	/* don't enable DDR controller yet */
-	im->ddr.sdram_cfg =
-		SDRAM_CFG_SREN |
-		SDRAM_CFG_SDRAM_TYPE_DDR1;
-	SYNC;
-
-	/* Set SDRAM mode */
-	im->ddr.sdram_mode =
-		((DDR_MODE_EXT_MODEREG | DDR_MODE_WEAK) <<
-			SDRAM_MODE_ESD_SHIFT) |
-		((DDR_MODE_MODEREG | DDR_MODE_BLEN_4) <<
-			SDRAM_MODE_SD_SHIFT) |
-		((DDR_MODE_CASLAT << SDRAM_MODE_SD_SHIFT) &
-			MODE_CASLAT);
-	SYNC;
-
-	/* Set fast SDRAM refresh rate */
-	im->ddr.sdram_interval =
-		(DDR_REFINT_166MHZ_7US << SDRAM_INTERVAL_REFINT_SHIFT) |
-		(DDR_BSTOPRE << SDRAM_INTERVAL_BSTOPRE_SHIFT);
-	SYNC;
-
-	/* Workaround for DDR6 Erratum
-	 * see MPC8349E Device Errata Rev.8, 2/2006
-	 * This workaround influences the MPC internal "input enables"
-	 * dependent on CAS latency and MPC revision. According to errata
-	 * sheet the internal reserved registers for this workaround are
-	 * not available from revision 2.0 and up.
-	 */
-
-	/* Get REVID from register SPRIDR. Skip workaround if rev >= 2.0
-	 * (0x200)
-	 */
-	if ((im->sysconf.spridr & SPRIDR_REVID) < 0x200) {
-
-		/* There is a internal reserved register at IMMRBAR+0x2F00
-		 * which has to be written with a certain value defined by
-		 * errata sheet.
-		 */
-		u32 *reserved_p = (u32 *)((u8 *)im + 0x2f00);
-
-#if defined(DDR_CASLAT_20)
-		*reserved_p = 0x201c0000;
-#else
-		*reserved_p = 0x202c0000;
-#endif
-	}
-}
-
-#ifdef CONFIG_OF_BOARD_SETUP
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
-	ft_cpu_setup(blob, bd);
-
-#ifdef CONFIG_PCI
-	ft_pci_setup(blob, bd);
-#endif	/* CONFIG_PCI */
-
-	return 0;
-}
-#endif	/* CONFIG_OF_BOARD_SETUP */
diff --git a/configs/TQM834x_defconfig b/configs/TQM834x_defconfig
deleted file mode 100644
index c29d8a8be1..0000000000
--- a/configs/TQM834x_defconfig
+++ /dev/null
@@ -1,166 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0x80000000
-CONFIG_ENV_SIZE=0x8000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_CLK_FREQ=66666000
-CONFIG_MPC83xx=y
-CONFIG_HIGH_BATS=y
-CONFIG_TARGET_TQM834X=y
-CONFIG_SYS_IMMR=0xff400000
-CONFIG_DDR_MC_CLOCK_MODE_1_1=y
-CONFIG_SYSTEM_PLL_FACTOR_4_1=y
-CONFIG_CORE_PLL_RATIO_2_1=y
-CONFIG_PCI_HOST_MODE_ENABLE=y
-CONFIG_PCI_INT_ARBITER1_ENABLE=y
-CONFIG_BOOT_MEMORY_SPACE_LOW=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC1_MODE_GMII=y
-CONFIG_TSEC2_MODE_GMII=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="SDRAM_LOWER"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_256_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="SDRAM_UPPER"
-CONFIG_BAT1_BASE=0x10000000
-CONFIG_BAT1_LENGTH_256_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="STACK_IN_DCACHE"
-CONFIG_BAT2_BASE=0x20000000
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="PCI_MEM_BASE"
-CONFIG_BAT3_BASE=0x90000000
-CONFIG_BAT3_LENGTH_256_MBYTES=y
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT3_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT4=y
-CONFIG_BAT4_NAME="PCI_MMIO"
-CONFIG_BAT4_BASE=0xA0000000
-CONFIG_BAT4_LENGTH_256_MBYTES=y
-CONFIG_BAT4_ACCESS_RW=y
-CONFIG_BAT4_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT4_ICACHE_GUARDED=y
-CONFIG_BAT4_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT4_DCACHE_GUARDED=y
-CONFIG_BAT4_USER_MODE_VALID=y
-CONFIG_BAT4_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT5=y
-CONFIG_BAT5_NAME="PCI_IO"
-CONFIG_BAT5_BASE=0xE2000000
-CONFIG_BAT5_LENGTH_16_MBYTES=y
-CONFIG_BAT5_ACCESS_RW=y
-CONFIG_BAT5_ICACHE_INHIBITED=y
-CONFIG_BAT5_ICACHE_GUARDED=y
-CONFIG_BAT5_DCACHE_INHIBITED=y
-CONFIG_BAT5_DCACHE_GUARDED=y
-CONFIG_BAT5_USER_MODE_VALID=y
-CONFIG_BAT5_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT6=y
-CONFIG_BAT6_NAME="IMMR"
-CONFIG_BAT6_BASE=0xFF400000
-CONFIG_BAT6_LENGTH_1_MBYTES=y
-CONFIG_BAT6_ACCESS_RW=y
-CONFIG_BAT6_ICACHE_INHIBITED=y
-CONFIG_BAT6_ICACHE_GUARDED=y
-CONFIG_BAT6_DCACHE_INHIBITED=y
-CONFIG_BAT6_DCACHE_GUARDED=y
-CONFIG_BAT6_USER_MODE_VALID=y
-CONFIG_BAT6_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT7=y
-CONFIG_BAT7_NAME="FLASH"
-CONFIG_BAT7_BASE=0x80000000
-CONFIG_BAT7_LENGTH_256_MBYTES=y
-CONFIG_BAT7_ACCESS_RW=y
-CONFIG_BAT7_ICACHE_INHIBITED=y
-CONFIG_BAT7_ICACHE_GUARDED=y
-CONFIG_BAT7_DCACHE_INHIBITED=y
-CONFIG_BAT7_DCACHE_GUARDED=y
-CONFIG_BAT7_USER_MODE_VALID=y
-CONFIG_BAT7_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0x80000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_1_GBYTES=y
-CONFIG_LBLAW1=y
-# CONFIG_LBLAW1_ENABLE is not set
-CONFIG_LBLAW2=y
-# CONFIG_LBLAW2_ENABLE is not set
-CONFIG_LBLAW3=y
-# CONFIG_LBLAW3_ENABLE is not set
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0x80000000
-CONFIG_BR0_PORTSIZE_32BIT=y
-CONFIG_OR0_AM_1_GBYTES=y
-CONFIG_OR0_SCY_5=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_QUARTER_CYCLE_EARLIER=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_8=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=6
-CONFIG_USE_PREBOOT=y
-CONFIG_PREBOOT="echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_EEPROM=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_JFFS2=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nor0=TQM834x-0"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=TQM834x-0:256k(u-boot),256k(env),1m(kernel),2m(initrd),-(user);"
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0x80060000
-CONFIG_ENV_ADDR_REDUND=0x80080000
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_EEPRO100=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
deleted file mode 100644
index aa70f01ddd..0000000000
--- a/include/configs/TQM834x.h
+++ /dev/null
@@ -1,277 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-/*
- * TQM8349 board configuration file
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300		1	/* E300 Family */
-
-/* board pre init: do not call, nothing to do */
-
-/* detect the number of flash banks */
-
-/*
- * DDR Setup
- */
-				/* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE	0x00000000
-#define DDR_CASLAT_25		/* CASLAT set to 2.5 */
-#undef CONFIG_DDR_ECC		/* only for ECC DDR module */
-#undef CONFIG_SPD_EEPROM	/* do not use SPD EEPROM for DDR setup */
-
-#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
-
-/*
- * FLASH on the Local Bus
- */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_BASE		0x80000000	/* start of FLASH   */
-#define CONFIG_SYS_FLASH_SIZE		8		/* FLASH size in MB */
-#define CONFIG_SYS_FLASH_EMPTY_INFO	/* print 'E' for empty sectors */
-
-/*
- * FLASH bank number detection
- */
-
-/*
- * When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is defined, the actual number of
- * Flash banks has to be determined at runtime and stored in a gloabl variable
- * tqm834x_num_flash_banks. The value of CONFIG_SYS_MAX_FLASH_BANKS_DETECT is
- * only used instead of CONFIG_SYS_MAX_FLASH_BANKS to allocate the array
- * flash_info, and should be made sufficiently large to accomodate the number
- * of banks that might actually be detected.  Since most (all?) Flash related
- * functions use CONFIG_SYS_MAX_FLASH_BANKS as the number of actual banks on
- * the board, it is defined as tqm834x_num_flash_banks.
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT	2
-
-#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max sectors per device */
-
-
-/* disable remaining mappings */
-#define CONFIG_SYS_BR1_PRELIM		0x00000000
-#define CONFIG_SYS_OR1_PRELIM		0x00000000
-
-#define CONFIG_SYS_BR2_PRELIM		0x00000000
-#define CONFIG_SYS_OR2_PRELIM		0x00000000
-
-#define CONFIG_SYS_BR3_PRELIM		0x00000000
-#define CONFIG_SYS_OR3_PRELIM		0x00000000
-
-/*
- * Monitor config
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#else
-# undef  CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0x20000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	\
-			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-				/* Reserve 384 kB = 3 sect. for Mon */
-#define CONFIG_SYS_MONITOR_LEN	(384 * 1024)
-				/* Reserve 512 kB for malloc */
-#define CONFIG_SYS_MALLOC_LEN	(512 * 1024)
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-
-/* I2C EEPROM, configuration for onboard EEPROMs 24C256 and 24C32 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2	/* 16 bit */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* 32 bytes/write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	12	/* 10ms +/- 20% */
-
-/* I2C RTC */
-#define CONFIG_RTC_DS1337			/* use ds1337 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR		0x68	/* at address 0x68 */
-
-/*
- * TSEC
- */
-
-#define CONFIG_SYS_TSEC1_OFFSET	0x24000
-#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET	0x25000
-#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_TSEC1		1
-#define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2		1
-#define CONFIG_TSEC2_NAME	"TSEC1"
-#define TSEC1_PHY_ADDR		2
-#define TSEC2_PHY_ADDR		1
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME		"TSEC0"
-
-#endif	/* CONFIG_TSEC_ENET */
-
-#if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-
-/* PCI1 host bridge */
-#define CONFIG_SYS_PCI1_MEM_BASE	0x90000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE	\
-			(CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
-#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE		0xe2000000
-#define CONFIG_SYS_PCI1_IO_PHYS		CONFIG_SYS_PCI1_IO_BASE
-#define CONFIG_SYS_PCI1_IO_SIZE		0x1000000	/* 16M */
-
-
-#if !defined(CONFIG_PCI_PNP)
-	#define PCI_ENET0_IOADDR	CONFIG_SYS_PCI1_IO_BASE
-	#define PCI_ENET0_MEMADDR	CONFIG_SYS_PCI1_MEM_BASE
-	#define PCI_IDSEL_NUMBER	0x1c    /* slot0 (IDSEL) = 28 */
-#endif
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID		0x1957  /* Freescale */
-
-#endif	/* CONFIG_PCI */
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO		1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-
-#undef CONFIG_WATCHDOG		/* watchdog disabled */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-				/* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
-
-/* System IO Config */
-#define CONFIG_SYS_SICRH	0
-#define CONFIG_SYS_SICRL	SICRL_LDP_A
-
-/* PCI */
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-				/* default location for tftp and bootm */
-#define CONFIG_LOADADDR		400000
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=tqm834x\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addcons=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
-	"flash_nfs_old=run nfsargs addip addcons;"			\
-		"bootm ${kernel_addr}\0"				\
-	"flash_nfs=run nfsargs addip addcons;"				\
-		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
-	"flash_self_old=run ramargs addip addcons;"			\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"flash_self=run ramargs addip addcons;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
-	"net_nfs_old=tftp 400000 ${bootfile};"				\
-		"run nfsargs addip addcons;bootm\0"			\
-	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
-		"tftp ${fdt_addr_r} ${fdt_file}; "			\
-		"run nfsargs addip addcons; "				\
-		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
-	"rootpath=/opt/eldk/ppc_6xx\0"					\
-	"bootfile=tqm834x/uImage\0"					\
-	"fdtfile=tqm834x/tqm834x.dtb\0"					\
-	"kernel_addr_r=400000\0"					\
-	"fdt_addr_r=600000\0"						\
-	"ramdisk_addr_r=800000\0"					\
-	"kernel_addr=800C0000\0"					\
-	"fdt_addr=800A0000\0"						\
-	"ramdisk_addr=80300000\0"					\
-	"u-boot=tqm834x/u-boot.bin\0"					\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"update=protect off 80000000 +${filesize};"			\
-		"era 80000000 +${filesize};"				\
-		"cp.b 200000 80000000 ${filesize}\0"			\
-	"upd=run load update\0"						\
-	""
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-/*
- * JFFS2 partitions
- */
-/* mtdparts command line support */
-
-/* default mtd partition table */
-#endif	/* __CONFIG_H */