leds: Add openfirmware platform device support

Add bindings to support LEDs defined as of_platform devices in addition to
the existing bindings for platform devices.

New options in Kconfig allow the platform binding code and/or the
of_platform code to be turned on.  The of_platform code is of course only
available on archs that have OF support.

The existing probe and remove methods are refactored to use new functions
create_gpio_led(), to create and register one led, and delete_gpio_led(),
to unregister and free one led.  The new probe and remove methods for the
of_platform driver can then share most of the common probe and remove code
with the platform driver.

The suspend and resume methods aren't shared, but they are very short.  The
actual led driving code is the same for LEDs created by either binding.

The OF bindings are based on patch by Anton Vorontsov
<avorontsov@ru.mvista.com>.  They have been extended to allow multiple LEDs
per device.

Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>

1 files changed, 37 insertions, 9 deletions

diff --git a/Documentation/powerpc/dts-bindings/gpio/led.txt b/Documentation/powerpc/dts-bindings/gpio/led.txt
index ff51f4c0fa9d..4fe14deedc0a 100644
--- a/Documentation/powerpc/dts-bindings/gpio/led.txt
+++ b/Documentation/powerpc/dts-bindings/gpio/led.txt
@@ -1,15 +1,43 @@
-LED connected to GPIO
+LEDs connected to GPIO lines
 
 Required properties:
-- compatible : should be "gpio-led".
-- label : (optional) the label for this LED. If omitted, the label is
+- compatible : should be "gpio-leds".
+
+Each LED is represented as a sub-node of the gpio-leds device.  Each
+node's name represents the name of the corresponding LED.
+
+LED sub-node properties:
+- gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
+  for devices" in Documentation/powerpc/booting-without-of.txt.  Active
+  low LEDs should be indicated using flags in the GPIO specifier.
+- label :  (optional) The label for this LED.  If omitted, the label is
   taken from the node name (excluding the unit address).
-- gpios : should specify LED GPIO.
+- linux,default-trigger :  (optional) This parameter, if present, is a
+  string defining the trigger assigned to the LED.  Current triggers are:
+    "backlight" - LED will act as a back-light, controlled by the framebuffer
+		  system
+    "default-on" - LED will turn on
+    "heartbeat" - LED "double" flashes at a load average based rate
+    "ide-disk" - LED indicates disk activity
+    "timer" - LED flashes at a fixed, configurable rate
 
-Example:
+Examples:
 
-led@0 {
-	compatible = "gpio-led";
-	label = "hdd";
-	gpios = <&mcu_pio 0 1>;
+leds {
+	compatible = "gpio-leds";
+	hdd {
+		label = "IDE Activity";
+		gpios = <&mcu_pio 0 1>; /* Active low */
+		linux,default-trigger = "ide-disk";
+	};
 };
+
+run-control {
+	compatible = "gpio-leds";
+	red {
+		gpios = <&mpc8572 6 0>;
+	};
+	green {
+		gpios = <&mpc8572 7 0>;
+	};
+}