[SSB]: add Sonics Silicon Backplane bus support

SSB is an SoC bus used in a number of embedded devices.  The most
well-known of these devices is probably the Linksys WRT54G, but there
are others as well.  The bus is also used internally on the BCM43xx
and BCM44xx devices from Broadcom.

This patch also includes support for SSB ID tables in modules, so
that SSB drivers can be loaded automatically.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 292 insertions, 0 deletions

diff --git a/include/linux/ssb/ssb_regs.h b/include/linux/ssb/ssb_regs.h
new file mode 100644
index 000000000000..47c7c71a5acf
--- /dev/null
+++ b/include/linux/ssb/ssb_regs.h
@@ -0,0 +1,292 @@
+#ifndef LINUX_SSB_REGS_H_
+#define LINUX_SSB_REGS_H_
+
+
+/* SiliconBackplane Address Map.
+ * All regions may not exist on all chips.
+ */
+#define SSB_SDRAM_BASE		0x00000000U	/* Physical SDRAM */
+#define SSB_PCI_MEM		0x08000000U	/* Host Mode sb2pcitranslation0 (64 MB) */
+#define SSB_PCI_CFG		0x0c000000U	/* Host Mode sb2pcitranslation1 (64 MB) */
+#define	SSB_SDRAM_SWAPPED	0x10000000U	/* Byteswapped Physical SDRAM */
+#define SSB_ENUM_BASE    	0x18000000U	/* Enumeration space base */
+#define	SSB_ENUM_LIMIT		0x18010000U	/* Enumeration space limit */
+
+#define	SSB_FLASH2		0x1c000000U	/* Flash Region 2 (region 1 shadowed here) */
+#define	SSB_FLASH2_SZ		0x02000000U	/* Size of Flash Region 2 */
+
+#define	SSB_EXTIF_BASE		0x1f000000U	/* External Interface region base address */
+#define	SSB_FLASH1		0x1fc00000U	/* Flash Region 1 */
+#define	SSB_FLASH1_SZ		0x00400000U	/* Size of Flash Region 1 */
+
+#define SSB_PCI_DMA		0x40000000U	/* Client Mode sb2pcitranslation2 (1 GB) */
+#define SSB_PCI_DMA_SZ		0x40000000U	/* Client Mode sb2pcitranslation2 size in bytes */
+#define SSB_PCIE_DMA_L32	0x00000000U	/* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), low 32 bits */
+#define SSB_PCIE_DMA_H32	0x80000000U	/* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), high 32 bits */
+#define	SSB_EUART		(SSB_EXTIF_BASE + 0x00800000)
+#define	SSB_LED			(SSB_EXTIF_BASE + 0x00900000)
+
+
+/* Enumeration space constants */
+#define SSB_CORE_SIZE		0x1000	/* Size of a core MMIO area */
+#define SSB_MAX_NR_CORES	((SSB_ENUM_LIMIT - SSB_ENUM_BASE) / SSB_CORE_SIZE)
+
+
+/* mips address */
+#define	SSB_EJTAG		0xff200000	/* MIPS EJTAG space (2M) */
+
+
+/* SSB PCI config space registers. */
+#define SSB_PMCSR		0x44
+#define  SSB_PE			0x100
+#define	SSB_BAR0_WIN		0x80	/* Backplane address space 0 */
+#define	SSB_BAR1_WIN		0x84	/* Backplane address space 1 */
+#define	SSB_SPROMCTL		0x88	/* SPROM control */
+#define  SSB_SPROMCTL_WE	0x10	/* SPROM write enable */
+#define	SSB_BAR1_CONTROL	0x8c	/* Address space 1 burst control */
+#define SSB_PCI_IRQS		0x90	/* PCI interrupts */
+#define SSB_PCI_IRQMASK		0x94	/* PCI IRQ control and mask (pcirev >= 6 only) */
+#define SSB_BACKPLANE_IRQS	0x98	/* Backplane Interrupts */
+#define SSB_GPIO_IN		0xB0	/* GPIO Input (pcirev >= 3 only) */
+#define SSB_GPIO_OUT		0xB4	/* GPIO Output (pcirev >= 3 only) */
+#define SSB_GPIO_OUT_ENABLE	0xB8	/* GPIO Output Enable/Disable (pcirev >= 3 only) */
+#define  SSB_GPIO_SCS		0x10	/* PCI config space bit 4 for 4306c0 slow clock source */
+#define  SSB_GPIO_HWRAD		0x20	/* PCI config space GPIO 13 for hw radio disable */
+#define  SSB_GPIO_XTAL		0x40	/* PCI config space GPIO 14 for Xtal powerup */
+#define  SSB_GPIO_PLL		0x80	/* PCI config space GPIO 15 for PLL powerdown */
+
+
+#define SSB_BAR0_MAX_RETRIES	50
+
+/* Silicon backplane configuration register definitions */
+#define SSB_IPSFLAG		0x0F08
+#define	 SSB_IPSFLAG_IRQ1	0x0000003F /* which sbflags get routed to mips interrupt 1 */
+#define	 SSB_IPSFLAG_IRQ1_SHIFT	0
+#define	 SSB_IPSFLAG_IRQ2	0x00003F00 /* which sbflags get routed to mips interrupt 2 */
+#define	 SSB_IPSFLAG_IRQ2_SHIFT	8
+#define	 SSB_IPSFLAG_IRQ3	0x003F0000 /* which sbflags get routed to mips interrupt 3 */
+#define	 SSB_IPSFLAG_IRQ3_SHIFT	16
+#define	 SSB_IPSFLAG_IRQ4	0x3F000000 /* which sbflags get routed to mips interrupt 4 */
+#define	 SSB_IPSFLAG_IRQ4_SHIFT	24
+#define SSB_TPSFLAG		0x0F18
+#define  SSB_TPSFLAG_BPFLAG	0x0000003F /* Backplane flag # */
+#define  SSB_TPSFLAG_ALWAYSIRQ	0x00000040 /* IRQ is always sent on the Backplane */
+#define SSB_TMERRLOGA		0x0F48
+#define SSB_TMERRLOG		0x0F50
+#define SSB_ADMATCH3		0x0F60
+#define SSB_ADMATCH2		0x0F68
+#define SSB_ADMATCH1		0x0F70
+#define SSB_IMSTATE		0x0F90     /* SB Initiator Agent State */
+#define  SSB_IMSTATE_PC		0x0000000f /* Pipe Count */
+#define  SSB_IMSTATE_AP_MASK	0x00000030 /* Arbitration Priority */
+#define  SSB_IMSTATE_AP_BOTH	0x00000000 /* Use both timeslices and token */
+#define  SSB_IMSTATE_AP_TS	0x00000010 /* Use timeslices only */
+#define  SSB_IMSTATE_AP_TK	0x00000020 /* Use token only */
+#define  SSB_IMSTATE_AP_RSV	0x00000030 /* Reserved */
+#define  SSB_IMSTATE_IBE	0x00020000 /* In Band Error */
+#define  SSB_IMSTATE_TO		0x00040000 /* Timeout */
+#define SSB_INTVEC		0x0F94     /* SB Interrupt Mask */
+#define  SSB_INTVEC_PCI		0x00000001 /* Enable interrupts for PCI */
+#define  SSB_INTVEC_ENET0	0x00000002 /* Enable interrupts for enet 0 */
+#define  SSB_INTVEC_ILINE20	0x00000004 /* Enable interrupts for iline20 */
+#define  SSB_INTVEC_CODEC	0x00000008 /* Enable interrupts for v90 codec */
+#define  SSB_INTVEC_USB		0x00000010 /* Enable interrupts for usb */
+#define  SSB_INTVEC_EXTIF	0x00000020 /* Enable interrupts for external i/f */
+#define  SSB_INTVEC_ENET1	0x00000040 /* Enable interrupts for enet 1 */
+#define SSB_TMSLOW		0x0F98     /* SB Target State Low */
+#define  SSB_TMSLOW_RESET	0x00000001 /* Reset */
+#define  SSB_TMSLOW_REJECT_22	0x00000002 /* Reject (Backplane rev 2.2) */
+#define  SSB_TMSLOW_REJECT_23	0x00000004 /* Reject (Backplane rev 2.3) */
+#define  SSB_TMSLOW_CLOCK	0x00010000 /* Clock Enable */
+#define  SSB_TMSLOW_FGC		0x00020000 /* Force Gated Clocks On */
+#define  SSB_TMSLOW_PE		0x40000000 /* Power Management Enable */
+#define  SSB_TMSLOW_BE		0x80000000 /* BIST Enable */
+#define SSB_TMSHIGH		0x0F9C     /* SB Target State High */
+#define  SSB_TMSHIGH_SERR	0x00000001 /* S-error */
+#define  SSB_TMSHIGH_INT	0x00000002 /* Interrupt */
+#define  SSB_TMSHIGH_BUSY	0x00000004 /* Busy */
+#define  SSB_TMSHIGH_TO		0x00000020 /* Timeout. Backplane rev >= 2.3 only */
+#define  SSB_TMSHIGH_COREFL	0x1FFF0000 /* Core specific flags */
+#define  SSB_TMSHIGH_COREFL_SHIFT	16
+#define  SSB_TMSHIGH_DMA64	0x10000000 /* 64bit DMA supported */
+#define  SSB_TMSHIGH_GCR	0x20000000 /* Gated Clock Request */
+#define  SSB_TMSHIGH_BISTF	0x40000000 /* BIST Failed */
+#define  SSB_TMSHIGH_BISTD	0x80000000 /* BIST Done */
+#define SSB_BWA0		0x0FA0
+#define SSB_IMCFGLO		0x0FA8
+#define  SSB_IMCFGLO_SERTO	0x00000007 /* Service timeout */
+#define  SSB_IMCFGLO_REQTO	0x00000070 /* Request timeout */
+#define  SSB_IMCFGLO_REQTO_SHIFT	4
+#define  SSB_IMCFGLO_CONNID	0x00FF0000 /* Connection ID */
+#define  SSB_IMCFGLO_CONNID_SHIFT	16
+#define SSB_IMCFGHI		0x0FAC
+#define SSB_ADMATCH0		0x0FB0
+#define SSB_TMCFGLO		0x0FB8
+#define SSB_TMCFGHI		0x0FBC
+#define SSB_BCONFIG		0x0FC0
+#define SSB_BSTATE		0x0FC8
+#define SSB_ACTCFG		0x0FD8
+#define SSB_FLAGST		0x0FE8
+#define SSB_IDLOW		0x0FF8
+#define  SSB_IDLOW_CFGSP	0x00000003 /* Config Space */
+#define  SSB_IDLOW_ADDRNGE	0x00000038 /* Address Ranges supported */
+#define  SSB_IDLOW_ADDRNGE_SHIFT	3
+#define  SSB_IDLOW_SYNC		0x00000040
+#define  SSB_IDLOW_INITIATOR	0x00000080
+#define  SSB_IDLOW_MIBL		0x00000F00 /* Minimum Backplane latency */
+#define  SSB_IDLOW_MIBL_SHIFT	8
+#define  SSB_IDLOW_MABL		0x0000F000 /* Maximum Backplane latency */
+#define  SSB_IDLOW_MABL_SHIFT	12
+#define  SSB_IDLOW_TIF		0x00010000 /* This Initiator is first */
+#define  SSB_IDLOW_CCW		0x000C0000 /* Cycle counter width */
+#define  SSB_IDLOW_CCW_SHIFT	18
+#define  SSB_IDLOW_TPT		0x00F00000 /* Target ports */
+#define  SSB_IDLOW_TPT_SHIFT	20
+#define  SSB_IDLOW_INITP	0x0F000000 /* Initiator ports */
+#define  SSB_IDLOW_INITP_SHIFT	24
+#define  SSB_IDLOW_SSBREV	0xF0000000 /* Sonics Backplane Revision code */
+#define  SSB_IDLOW_SSBREV_22	0x00000000 /* <= 2.2 */
+#define  SSB_IDLOW_SSBREV_23	0x10000000 /* 2.3 */
+#define SSB_IDHIGH		0x0FFC     /* SB Identification High */
+#define  SSB_IDHIGH_RCLO	0x0000000F /* Revision Code (low part) */
+#define  SSB_IDHIGH_CC		0x00008FF0 /* Core Code */
+#define  SSB_IDHIGH_CC_SHIFT	4
+#define  SSB_IDHIGH_RCHI	0x00007000 /* Revision Code (high part) */
+#define  SSB_IDHIGH_RCHI_SHIFT	8	   /* yes, shift 8 is right */
+#define  SSB_IDHIGH_VC		0xFFFF0000 /* Vendor Code */
+#define  SSB_IDHIGH_VC_SHIFT	16
+
+/* SPROM shadow area. If not otherwise noted, fields are
+ * two bytes wide. Note that the SPROM can _only_ be read
+ * in two-byte quantinies.
+ */
+#define SSB_SPROMSIZE_WORDS		64
+#define SSB_SPROMSIZE_BYTES		(SSB_SPROMSIZE_WORDS * sizeof(u16))
+#define SSB_SPROM_BASE			0x1000
+#define SSB_SPROM_REVISION		0x107E
+#define  SSB_SPROM_REVISION_REV		0x00FF	/* SPROM Revision number */
+#define  SSB_SPROM_REVISION_CRC		0xFF00	/* SPROM CRC8 value */
+#define  SSB_SPROM_REVISION_CRC_SHIFT	8
+/* SPROM Revision 1 */
+#define SSB_SPROM1_SPID			0x1004	/* Subsystem Product ID for PCI */
+#define SSB_SPROM1_SVID			0x1006	/* Subsystem Vendor ID for PCI */
+#define SSB_SPROM1_PID			0x1008	/* Product ID for PCI */
+#define SSB_SPROM1_IL0MAC		0x1048	/* 6 bytes MAC address for 802.11b/g */
+#define SSB_SPROM1_ET0MAC		0x104E	/* 6 bytes MAC address for Ethernet */
+#define SSB_SPROM1_ET1MAC		0x1054	/* 6 bytes MAC address for 802.11a */
+#define SSB_SPROM1_ETHPHY		0x105A	/* Ethernet PHY settings */
+#define  SSB_SPROM1_ETHPHY_ET0A		0x001F	/* MII Address for enet0 */
+#define  SSB_SPROM1_ETHPHY_ET1A		0x03E0	/* MII Address for enet1 */
+#define  SSB_SPROM1_ETHPHY_ET1A_SHIFT	5
+#define  SSB_SPROM1_ETHPHY_ET0M		(1<<14)	/* MDIO for enet0 */
+#define  SSB_SPROM1_ETHPHY_ET1M		(1<<15)	/* MDIO for enet1 */
+#define SSB_SPROM1_BINF			0x105C	/* Board info */
+#define  SSB_SPROM1_BINF_BREV		0x00FF	/* Board Revision */
+#define  SSB_SPROM1_BINF_CCODE		0x0F00	/* Country Code */
+#define  SSB_SPROM1_BINF_CCODE_SHIFT	8
+#define  SSB_SPROM1_BINF_ANTA		0x3000	/* Available A-PHY antennas */
+#define  SSB_SPROM1_BINF_ANTA_SHIFT	12
+#define  SSB_SPROM1_BINF_ANTBG		0xC000	/* Available B-PHY antennas */
+#define  SSB_SPROM1_BINF_ANTBG_SHIFT	14
+#define SSB_SPROM1_PA0B0		0x105E
+#define SSB_SPROM1_PA0B1		0x1060
+#define SSB_SPROM1_PA0B2		0x1062
+#define SSB_SPROM1_GPIOA		0x1064	/* General Purpose IO pins 0 and 1 */
+#define  SSB_SPROM1_GPIOA_P0		0x00FF	/* Pin 0 */
+#define  SSB_SPROM1_GPIOA_P1		0xFF00	/* Pin 1 */
+#define  SSB_SPROM1_GPIOA_P1_SHIFT	8
+#define SSB_SPROM1_GPIOB		0x1066	/* General Purpuse IO pins 2 and 3 */
+#define  SSB_SPROM1_GPIOB_P2		0x00FF	/* Pin 2 */
+#define  SSB_SPROM1_GPIOB_P3		0xFF00	/* Pin 3 */
+#define  SSB_SPROM1_GPIOB_P3_SHIFT	8
+#define SSB_SPROM1_MAXPWR		0x1068	/* Power Amplifier Max Power */
+#define  SSB_SPROM1_MAXPWR_BG		0x00FF	/* B-PHY and G-PHY (in dBm Q5.2) */
+#define  SSB_SPROM1_MAXPWR_A		0xFF00	/* A-PHY (in dBm Q5.2) */
+#define  SSB_SPROM1_MAXPWR_A_SHIFT	8
+#define SSB_SPROM1_PA1B0		0x106A
+#define SSB_SPROM1_PA1B1		0x106C
+#define SSB_SPROM1_PA1B2		0x106E
+#define SSB_SPROM1_ITSSI		0x1070	/* Idle TSSI Target */
+#define  SSB_SPROM1_ITSSI_BG		0x00FF	/* B-PHY and G-PHY*/
+#define  SSB_SPROM1_ITSSI_A		0xFF00	/* A-PHY */
+#define  SSB_SPROM1_ITSSI_A_SHIFT	8
+#define SSB_SPROM1_BFLLO		0x1072	/* Boardflags (low 16 bits) */
+#define SSB_SPROM1_AGAIN		0x1074	/* Antenna Gain (in dBm Q5.2) */
+#define  SSB_SPROM1_AGAIN_A		0x00FF	/* A-PHY */
+#define  SSB_SPROM1_AGAIN_BG		0xFF00	/* B-PHY and G-PHY */
+#define  SSB_SPROM1_AGAIN_BG_SHIFT	8
+#define SSB_SPROM1_OEM			0x1076	/* 8 bytes OEM string (rev 1 only) */
+/* SPROM Revision 2 (inherits from rev 1) */
+#define SSB_SPROM2_BFLHI		0x1038	/* Boardflags (high 16 bits) */
+#define SSB_SPROM2_MAXP_A		0x103A	/* A-PHY Max Power */
+#define  SSB_SPROM2_MAXP_A_HI		0x00FF	/* Max Power High */
+#define  SSB_SPROM2_MAXP_A_LO		0xFF00	/* Max Power Low */
+#define  SSB_SPROM2_MAXP_A_LO_SHIFT	8
+#define SSB_SPROM2_PA1LOB0		0x103C	/* A-PHY PowerAmplifier Low Settings */
+#define SSB_SPROM2_PA1LOB1		0x103E	/* A-PHY PowerAmplifier Low Settings */
+#define SSB_SPROM2_PA1LOB2		0x1040	/* A-PHY PowerAmplifier Low Settings */
+#define SSB_SPROM2_PA1HIB0		0x1042	/* A-PHY PowerAmplifier High Settings */
+#define SSB_SPROM2_PA1HIB1		0x1044	/* A-PHY PowerAmplifier High Settings */
+#define SSB_SPROM2_PA1HIB2		0x1046	/* A-PHY PowerAmplifier High Settings */
+#define SSB_SPROM2_OPO			0x1078	/* OFDM Power Offset from CCK Level */
+#define  SSB_SPROM2_OPO_VALUE		0x00FF
+#define  SSB_SPROM2_OPO_UNUSED		0xFF00
+#define SSB_SPROM2_CCODE		0x107C	/* Two char Country Code */
+/* SPROM Revision 3 (inherits from rev 2) */
+#define SSB_SPROM3_OFDMAPO		0x102C	/* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */
+#define SSB_SPROM3_OFDMALPO		0x1030	/* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */
+#define SSB_SPROM3_OFDMAHPO		0x1034	/* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */
+#define SSB_SPROM3_GPIOLDC		0x1042	/* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */
+#define  SSB_SPROM3_GPIOLDC_OFF		0x0000FF00	/* Off Count */
+#define  SSB_SPROM3_GPIOLDC_OFF_SHIFT	8
+#define  SSB_SPROM3_GPIOLDC_ON		0x00FF0000	/* On Count */
+#define  SSB_SPROM3_GPIOLDC_ON_SHIFT	16
+#define SSB_SPROM3_CCKPO		0x1078	/* CCK Power Offset */
+#define  SSB_SPROM3_CCKPO_1M		0x000F	/* 1M Rate PO */
+#define  SSB_SPROM3_CCKPO_2M		0x00F0	/* 2M Rate PO */
+#define  SSB_SPROM3_CCKPO_2M_SHIFT	4
+#define  SSB_SPROM3_CCKPO_55M		0x0F00	/* 5.5M Rate PO */
+#define  SSB_SPROM3_CCKPO_55M_SHIFT	8
+#define  SSB_SPROM3_CCKPO_11M		0xF000	/* 11M Rate PO */
+#define  SSB_SPROM3_CCKPO_11M_SHIFT	12
+#define  SSB_SPROM3_OFDMGPO		0x107A	/* G-PHY OFDM Power Offset (4 bytes, BigEndian) */
+
+/* Values for SSB_SPROM1_BINF_CCODE */
+enum {
+	SSB_SPROM1CCODE_WORLD = 0,
+	SSB_SPROM1CCODE_THAILAND,
+	SSB_SPROM1CCODE_ISRAEL,
+	SSB_SPROM1CCODE_JORDAN,
+	SSB_SPROM1CCODE_CHINA,
+	SSB_SPROM1CCODE_JAPAN,
+	SSB_SPROM1CCODE_USA_CANADA_ANZ,
+	SSB_SPROM1CCODE_EUROPE,
+	SSB_SPROM1CCODE_USA_LOW,
+	SSB_SPROM1CCODE_JAPAN_HIGH,
+	SSB_SPROM1CCODE_ALL,
+	SSB_SPROM1CCODE_NONE,
+};
+
+/* Address-Match values and masks (SSB_ADMATCHxxx) */
+#define SSB_ADM_TYPE			0x00000003	/* Address type */
+#define  SSB_ADM_TYPE0			0
+#define  SSB_ADM_TYPE1			1
+#define  SSB_ADM_TYPE2			2
+#define SSB_ADM_AD64			0x00000004
+#define SSB_ADM_SZ0			0x000000F8	/* Type0 size */
+#define SSB_ADM_SZ0_SHIFT		3
+#define SSB_ADM_SZ1			0x000001F8	/* Type1 size */
+#define SSB_ADM_SZ1_SHIFT		3
+#define SSB_ADM_SZ2			0x000001F8	/* Type2 size */
+#define SSB_ADM_SZ2_SHIFT		3
+#define SSB_ADM_EN			0x00000400	/* Enable */
+#define SSB_ADM_NEG			0x00000800	/* Negative decode */
+#define SSB_ADM_BASE0			0xFFFFFF00	/* Type0 base address */
+#define SSB_ADM_BASE0_SHIFT		8
+#define SSB_ADM_BASE1			0xFFFFF000	/* Type1 base address for the core */
+#define SSB_ADM_BASE1_SHIFT		12
+#define SSB_ADM_BASE2			0xFFFF0000	/* Type2 base address for the core */
+#define SSB_ADM_BASE2_SHIFT		16
+
+
+#endif /* LINUX_SSB_REGS_H_ */