Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
	drivers/net/ethernet/rocker/rocker.c

The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.

Signed-off-by: David S. Miller <davem@davemloft.net>

36 files changed, 771 insertions, 71 deletions

diff --git a/Documentation/devicetree/bindings/clock/exynos7-clock.txt b/Documentation/devicetree/bindings/clock/exynos7-clock.txt
index 6d3d5f80c1c3..6bf1e7493f61 100644
--- a/Documentation/devicetree/bindings/clock/exynos7-clock.txt
+++ b/Documentation/devicetree/bindings/clock/exynos7-clock.txt
@@ -34,6 +34,8 @@ Required Properties for Clock Controller:
 	- "samsung,exynos7-clock-peris"
 	- "samsung,exynos7-clock-fsys0"
 	- "samsung,exynos7-clock-fsys1"
+	- "samsung,exynos7-clock-mscl"
+	- "samsung,exynos7-clock-aud"
 
  - reg: physical base address of the controller and the length of
 	memory mapped region.
@@ -53,6 +55,7 @@ Input clocks for top0 clock controller:
 	- dout_sclk_bus1_pll
 	- dout_sclk_cc_pll
 	- dout_sclk_mfc_pll
+	- dout_sclk_aud_pll
 
 Input clocks for top1 clock controller:
 	- fin_pll
@@ -76,6 +79,14 @@ Input clocks for peric1 clock controller:
 	- sclk_uart1
 	- sclk_uart2
 	- sclk_uart3
+	- sclk_spi0
+	- sclk_spi1
+	- sclk_spi2
+	- sclk_spi3
+	- sclk_spi4
+	- sclk_i2s1
+	- sclk_pcm1
+	- sclk_spdif
 
 Input clocks for peris clock controller:
 	- fin_pll
@@ -91,3 +102,7 @@ Input clocks for fsys1 clock controller:
 	- dout_aclk_fsys1_200
 	- dout_sclk_mmc0
 	- dout_sclk_mmc1
+
+Input clocks for aud clock controller:
+	- fin_pll
+	- fout_aud_pll
diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt
index ded5d6212c84..c6620bc96703 100644
--- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt
+++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt
@@ -1,4 +1,4 @@
-NVIDIA Tegra124 Clock And Reset Controller
+NVIDIA Tegra124 and Tegra132 Clock And Reset Controller
 
 This binding uses the common clock binding:
 Documentation/devicetree/bindings/clock/clock-bindings.txt
@@ -7,14 +7,16 @@ The CAR (Clock And Reset) Controller on Tegra is the HW module responsible
 for muxing and gating Tegra's clocks, and setting their rates.
 
 Required properties :
-- compatible : Should be "nvidia,tegra124-car"
+- compatible : Should be "nvidia,tegra124-car" or "nvidia,tegra132-car"
 - reg : Should contain CAR registers location and length
 - clocks : Should contain phandle and clock specifiers for two clocks:
   the 32 KHz "32k_in", and the board-specific oscillator "osc".
 - #clock-cells : Should be 1.
   In clock consumers, this cell represents the clock ID exposed by the
-  CAR. The assignments may be found in header file
-  <dt-bindings/clock/tegra124-car.h>.
+  CAR. The assignments may be found in the header files
+  <dt-bindings/clock/tegra124-car-common.h> (which covers IDs common
+  to Tegra124 and Tegra132) and <dt-bindings/clock/tegra124-car.h>
+  (for Tegra124-specific clocks).
 - #reset-cells : Should be 1.
   In clock consumers, this cell represents the bit number in the CAR's
   array of CLK_RST_CONTROLLER_RST_DEVICES_* registers.
diff --git a/Documentation/devicetree/bindings/clock/qcom,lcc.txt b/Documentation/devicetree/bindings/clock/qcom,lcc.txt
new file mode 100644
index 000000000000..dd755be63a01
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,lcc.txt
@@ -0,0 +1,21 @@
+Qualcomm LPASS Clock & Reset Controller Binding
+------------------------------------------------
+
+Required properties :
+- compatible : shall contain only one of the following:
+
+			"qcom,lcc-msm8960"
+			"qcom,lcc-apq8064"
+			"qcom,lcc-ipq8064"
+
+- reg : shall contain base register location and length
+- #clock-cells : shall contain 1
+- #reset-cells : shall contain 1
+
+Example:
+	clock-controller@28000000 {
+		compatible = "qcom,lcc-ipq8064";
+		reg = <0x28000000 0x1000>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
diff --git a/Documentation/devicetree/bindings/clock/qoriq-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt
index 266ff9d23229..df4a259a6898 100644
--- a/Documentation/devicetree/bindings/clock/qoriq-clock.txt
+++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt
@@ -1,6 +1,6 @@
-* Clock Block on Freescale CoreNet Platforms
+* Clock Block on Freescale QorIQ Platforms
 
-Freescale CoreNet chips take primary clocking input from the external
+Freescale qoriq chips take primary clocking input from the external
 SYSCLK signal. The SYSCLK input (frequency) is multiplied using
 multiple phase locked loops (PLL) to create a variety of frequencies
 which can then be passed to a variety of internal logic, including
@@ -29,6 +29,7 @@ Required properties:
 	* "fsl,t4240-clockgen"
 	* "fsl,b4420-clockgen"
 	* "fsl,b4860-clockgen"
+	* "fsl,ls1021a-clockgen"
 	Chassis clock strings include:
 	* "fsl,qoriq-clockgen-1.0": for chassis 1.0 clocks
 	* "fsl,qoriq-clockgen-2.0": for chassis 2.0 clocks
diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt
index 2e18676bd4b5..0a80fa70ca26 100644
--- a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt
+++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt
@@ -11,6 +11,7 @@ Required Properties:
 
   - compatible: Must be one of the following
     - "renesas,r7s72100-mstp-clocks" for R7S72100 (RZ) MSTP gate clocks
+    - "renesas,r8a73a4-mstp-clocks" for R8A73A4 (R-Mobile APE6) MSTP gate clocks
     - "renesas,r8a7740-mstp-clocks" for R8A7740 (R-Mobile A1) MSTP gate clocks
     - "renesas,r8a7779-mstp-clocks" for R8A7779 (R-Car H1) MSTP gate clocks
     - "renesas,r8a7790-mstp-clocks" for R8A7790 (R-Car H2) MSTP gate clocks
diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a73a4-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a73a4-cpg-clocks.txt
new file mode 100644
index 000000000000..ece92393e80d
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/renesas,r8a73a4-cpg-clocks.txt
@@ -0,0 +1,33 @@
+* Renesas R8A73A4 Clock Pulse Generator (CPG)
+
+The CPG generates core clocks for the R8A73A4 SoC. It includes five PLLs
+and several fixed ratio dividers.
+
+Required Properties:
+
+  - compatible: Must be "renesas,r8a73a4-cpg-clocks"
+
+  - reg: Base address and length of the memory resource used by the CPG
+
+  - clocks: Reference to the parent clocks ("extal1" and "extal2")
+
+  - #clock-cells: Must be 1
+
+  - clock-output-names: The names of the clocks. Supported clocks are "main",
+    "pll0", "pll1", "pll2", "pll2s", "pll2h", "z", "z2", "i", "m3", "b",
+    "m1", "m2", "zx", "zs", and "hp".
+
+
+Example
+-------
+
+        cpg_clocks: cpg_clocks@e6150000 {
+                compatible = "renesas,r8a73a4-cpg-clocks";
+                reg = <0 0xe6150000 0 0x10000>;
+                clocks = <&extal1_clk>, <&extal2_clk>;
+                #clock-cells = <1>;
+                clock-output-names = "main", "pll0", "pll1", "pll2",
+                                     "pll2s", "pll2h", "z", "z2",
+                                     "i", "m3", "b", "m1", "m2",
+                                     "zx", "zs", "hp";
+        };
diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt
index e6ad35b894f9..b02944fba9de 100644
--- a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt
+++ b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt
@@ -8,15 +8,18 @@ Required Properties:
   - compatible: Must be one of
     - "renesas,r8a7790-cpg-clocks" for the r8a7790 CPG
     - "renesas,r8a7791-cpg-clocks" for the r8a7791 CPG
+    - "renesas,r8a7793-cpg-clocks" for the r8a7793 CPG
     - "renesas,r8a7794-cpg-clocks" for the r8a7794 CPG
     - "renesas,rcar-gen2-cpg-clocks" for the generic R-Car Gen2 CPG
 
   - reg: Base address and length of the memory resource used by the CPG
 
-  - clocks: Reference to the parent clock
+  - clocks: References to the parent clocks: first to the EXTAL clock, second
+    to the USB_EXTAL clock
   - #clock-cells: Must be 1
   - clock-output-names: The names of the clocks. Supported clocks are "main",
-    "pll0", "pll1", "pll3", "lb", "qspi", "sdh", "sd0", "sd1" and "z"
+    "pll0", "pll1", "pll3", "lb", "qspi", "sdh", "sd0", "sd1", "z", "rcan", and
+    "adsp"
 
 
 Example
@@ -26,8 +29,9 @@ Example
 		compatible = "renesas,r8a7790-cpg-clocks",
 			     "renesas,rcar-gen2-cpg-clocks";
 		reg = <0 0xe6150000 0 0x1000>;
-		clocks = <&extal_clk>;
+		clocks = <&extal_clk &usb_extal_clk>;
 		#clock-cells = <1>;
 		clock-output-names = "main", "pll0, "pll1", "pll3",
-				     "lb", "qspi", "sdh", "sd0", "sd1", "z";
+				     "lb", "qspi", "sdh", "sd0", "sd1", "z",
+				     "rcan", "adsp";
 	};
diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 67b2b99f2b33..60b44285250d 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -26,7 +26,7 @@ Required properties:
 	"allwinner,sun5i-a10s-ahb-gates-clk" - for the AHB gates on A10s
 	"allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20
 	"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
-	"allwinner,sun6i-a31-ahb1-mux-clk" - for the AHB1 multiplexer on A31
+	"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
 	"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
 	"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
 	"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
@@ -55,9 +55,11 @@ Required properties:
 	"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
 	"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
 	"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
-	"allwinner,sun4i-a10-mmc-output-clk" - for the MMC output clock on A10
-	"allwinner,sun4i-a10-mmc-sample-clk" - for the MMC sample clock on A10
+	"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
+	"allwinner,sun9i-a80-mmc-clk" - for mmc module clocks on A80
+	"allwinner,sun9i-a80-mmc-config-clk" - for mmc gates + resets on A80
 	"allwinner,sun4i-a10-mod0-clk" - for the module 0 family of clocks
+	"allwinner,sun9i-a80-mod0-clk" - for module 0 (storage) clocks on A80
 	"allwinner,sun8i-a23-mbus-clk" - for the MBUS clock on A23
 	"allwinner,sun7i-a20-out-clk" - for the external output clocks
 	"allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31
@@ -73,7 +75,9 @@ Required properties for all clocks:
 - #clock-cells : from common clock binding; shall be set to 0 except for
 	the following compatibles where it shall be set to 1:
 	"allwinner,*-gates-clk", "allwinner,sun4i-pll5-clk",
-	"allwinner,sun4i-pll6-clk", "allwinner,sun6i-a31-pll6-clk"
+	"allwinner,sun4i-pll6-clk", "allwinner,sun6i-a31-pll6-clk",
+	"allwinner,*-usb-clk", "allwinner,*-mmc-clk",
+	"allwinner,*-mmc-config-clk"
 - clock-output-names : shall be the corresponding names of the outputs.
 	If the clock module only has one output, the name shall be the
 	module name.
@@ -81,6 +85,10 @@ Required properties for all clocks:
 And "allwinner,*-usb-clk" clocks also require:
 - reset-cells : shall be set to 1
 
+The "allwinner,sun9i-a80-mmc-config-clk" clock also requires:
+- #reset-cells : shall be set to 1
+- resets : shall be the reset control phandle for the mmc block.
+
 For "allwinner,sun7i-a20-gmac-clk", the parent clocks shall be fixed rate
 dummy clocks at 25 MHz and 125 MHz, respectively. See example.
 
@@ -95,6 +103,14 @@ For "allwinner,sun6i-a31-pll6-clk", there are 2 outputs. The first output
 is the normal PLL6 output, or "pll6". The second output is rate doubled
 PLL6, or "pll6x2".
 
+The "allwinner,*-mmc-clk" clocks have three different outputs: the
+main clock, with the ID 0, and the output and sample clocks, with the
+IDs 1 and 2, respectively.
+
+The "allwinner,sun9i-a80-mmc-config-clk" clock has one clock/reset output
+per mmc controller. The number of outputs is determined by the size of
+the address block, which is related to the overall mmc block.
+
 For example:
 
 osc24M: clk@01c20050 {
@@ -138,11 +154,11 @@ cpu: cpu@01c20054 {
 };
 
 mmc0_clk: clk@01c20088 {
-	#clock-cells = <0>;
-	compatible = "allwinner,sun4i-mod0-clk";
+	#clock-cells = <1>;
+	compatible = "allwinner,sun4i-a10-mmc-clk";
 	reg = <0x01c20088 0x4>;
 	clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-	clock-output-names = "mmc0";
+	clock-output-names = "mmc0", "mmc0_output", "mmc0_sample";
 };
 
 mii_phy_tx_clk: clk@2 {
@@ -170,3 +186,16 @@ gmac_clk: clk@01c20164 {
 	clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>;
 	clock-output-names = "gmac";
 };
+
+mmc_config_clk: clk@01c13000 {
+	compatible = "allwinner,sun9i-a80-mmc-config-clk";
+	reg = <0x01c13000 0x10>;
+	clocks = <&ahb0_gates 8>;
+	clock-names = "ahb";
+	resets = <&ahb0_resets 8>;
+	reset-names = "ahb";
+	#clock-cells = <1>;
+	#reset-cells = <1>;
+	clock-output-names = "mmc0_config", "mmc1_config",
+			     "mmc2_config", "mmc3_config";
+};
diff --git a/Documentation/devicetree/bindings/clock/ti,cdce706.txt b/Documentation/devicetree/bindings/clock/ti,cdce706.txt
new file mode 100644
index 000000000000..616836e7e1e2
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti,cdce706.txt
@@ -0,0 +1,42 @@
+Bindings for Texas Instruments CDCE706 programmable 3-PLL clock
+synthesizer/multiplier/divider.
+
+Reference: http://www.ti.com/lit/ds/symlink/cdce706.pdf
+
+I2C device node required properties:
+- compatible: shall be "ti,cdce706".
+- reg: i2c device address, shall be in range [0x68...0x6b].
+- #clock-cells: from common clock binding; shall be set to 1.
+- clocks: from common clock binding; list of parent clock
+  handles, shall be reference clock(s) connected to CLK_IN0
+  and CLK_IN1 pins.
+- clock-names: shall be clk_in0 and/or clk_in1. Use clk_in0
+  in case of crystal oscillator or differential signal input
+  configuration. Use clk_in0 and clk_in1 in case of independent
+  single-ended LVCMOS inputs configuration.
+
+Example:
+
+	clocks {
+		clk54: clk54 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <54000000>;
+		};
+	};
+	...
+	i2c0: i2c-master@0d090000 {
+		...
+		cdce706: clock-synth@69 {
+			compatible = "ti,cdce706";
+			#clock-cells = <1>;
+			reg = <0x69>;
+			clocks = <&clk54>;
+			clock-names = "clk_in0";
+		};
+	};
+	...
+	simple-audio-card,codec {
+		...
+		clocks = <&cdce706 4>;
+	};
diff --git a/Documentation/devicetree/bindings/clock/ti/fapll.txt b/Documentation/devicetree/bindings/clock/ti/fapll.txt
new file mode 100644
index 000000000000..c19b3f253b8c
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti/fapll.txt
@@ -0,0 +1,33 @@
+Binding for Texas Instruments FAPLL clock.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1]. It assumes a
+register-mapped FAPLL with usually two selectable input clocks
+(reference clock and bypass clock), and one or more child
+syntesizers.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be "ti,dm816-fapll-clock"
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : link phandles of parent clocks (clk-ref and clk-bypass)
+- reg : address and length of the register set for controlling the FAPLL.
+
+Examples:
+	main_fapll: main_fapll {
+		#clock-cells = <1>;
+		compatible = "ti,dm816-fapll-clock";
+		reg = <0x400 0x40>;
+		clocks = <&sys_clkin_ck &sys_clkin_ck>;
+		clock-indices = <1>, <2>, <3>, <4>, <5>,
+				<6>, <7>;
+		clock-output-names = "main_pll_clk1",
+				     "main_pll_clk2",
+				     "main_pll_clk3",
+				     "main_pll_clk4",
+				     "main_pll_clk5",
+				     "main_pll_clk6",
+				     "main_pll_clk7";
+	};
diff --git a/Documentation/devicetree/bindings/dma/img-mdc-dma.txt b/Documentation/devicetree/bindings/dma/img-mdc-dma.txt
new file mode 100644
index 000000000000..28c1341db346
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/img-mdc-dma.txt
@@ -0,0 +1,57 @@
+* IMG Multi-threaded DMA Controller (MDC)
+
+Required properties:
+- compatible: Must be "img,pistachio-mdc-dma".
+- reg: Must contain the base address and length of the MDC registers.
+- interrupts: Must contain all the per-channel DMA interrupts.
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clock/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  - sys: MDC system interface clock.
+- img,cr-periph: Must contain a phandle to the peripheral control syscon
+  node which contains the DMA request to channel mapping registers.
+- img,max-burst-multiplier: Must be the maximum supported burst size multiplier.
+  The maximum burst size is this value multiplied by the hardware-reported bus
+  width.
+- #dma-cells: Must be 3:
+  - The first cell is the peripheral's DMA request line.
+  - The second cell is a bitmap specifying to which channels the DMA request
+    line may be mapped (i.e. bit N set indicates channel N is usable).
+  - The third cell is the thread ID to be used by the channel.
+
+Optional properties:
+- dma-channels: Number of supported DMA channels, up to 32.  If not specified
+  the number reported by the hardware is used.
+
+Example:
+
+mdc: dma-controller@18143000 {
+	compatible = "img,pistachio-mdc-dma";
+	reg = <0x18143000 0x1000>;
+	interrupts = <GIC_SHARED 27 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 28 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 29 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 30 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 31 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 32 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 33 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 34 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 35 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 36 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 37 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SHARED 38 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&system_clk>;
+	clock-names = "sys";
+
+	img,max-burst-multiplier = <16>;
+	img,cr-periph = <&cr_periph>;
+
+	#dma-cells = <3>;
+};
+
+spi@18100f00 {
+	...
+	dmas = <&mdc 9 0xffffffff 0>, <&mdc 10 0xffffffff 0>;
+	dma-names = "tx", "rx";
+	...
+};
diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt
index f7e21b1c2a05..09daeef1ff22 100644
--- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt
+++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt
@@ -5,9 +5,6 @@ controller instances named DMAC capable of serving multiple clients. Channels
 can be dedicated to specific clients or shared between a large number of
 clients.
 
-DMA clients are connected to the DMAC ports referenced by an 8-bit identifier
-called MID/RID.
-
 Each DMA client is connected to one dedicated port of the DMAC, identified by
 an 8-bit port number called the MID/RID. A DMA controller can thus serve up to
 256 clients in total. When the number of hardware channels is lower than the
diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt
index d58675ea1abf..c261598164a7 100644
--- a/Documentation/devicetree/bindings/dma/snps-dma.txt
+++ b/Documentation/devicetree/bindings/dma/snps-dma.txt
@@ -38,7 +38,7 @@ Example:
 		chan_allocation_order = <1>;
 		chan_priority = <1>;
 		block_size = <0xfff>;
-		data_width = <3 3 0 0>;
+		data_width = <3 3>;
 	};
 
 DMA clients connected to the Designware DMA controller must use the format
diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
new file mode 100644
index 000000000000..81f982ccca31
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
@@ -0,0 +1,37 @@
+Broadcom iProc I2C controller
+
+Required properties:
+
+- compatible:
+    Must be "brcm,iproc-i2c"
+
+- reg:
+    Define the base and range of the I/O address space that contain the iProc
+    I2C controller registers
+
+- interrupts:
+    Should contain the I2C interrupt
+
+- clock-frequency:
+    This is the I2C bus clock. Need to be either 100000 or 400000
+
+- #address-cells:
+    Always 1 (for I2C addresses)
+
+- #size-cells:
+    Always 0
+
+Example:
+	i2c0: i2c@18008000 {
+		compatible = "brcm,iproc-i2c";
+		reg = <0x18008000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+		clock-frequency = <100000>;
+
+		codec: wm8750@1a {
+			compatible = "wlf,wm8750";
+			reg = <0x1a>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
index 34a3fb6f8488..cf53d5fba20a 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
@@ -16,6 +16,9 @@ Required Properties:
 Optional Properties:
 
   - reset-gpios: Reference to the GPIO connected to the reset input.
+  - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all
+    children in idle state. This is necessary for example, if there are several
+    multiplexers on the bus and the devices behind them use same I2C addresses.
 
 
 Example:
diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt
index 1637c298a1b3..17bef9a34e50 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt
@@ -4,24 +4,60 @@ Required properties:
 - compatible      : "opencores,i2c-ocores" or "aeroflexgaisler,i2cmst"
 - reg             : bus address start and address range size of device
 - interrupts      : interrupt number
-- clock-frequency : frequency of bus clock in Hz
+- clocks          : handle to the controller clock; see the note below.
+                    Mutually exclusive with opencores,ip-clock-frequency
+- opencores,ip-clock-frequency: frequency of the controller clock in Hz;
+                    see the note below. Mutually exclusive with clocks
 - #address-cells  : should be <1>
 - #size-cells     : should be <0>
 
 Optional properties:
+- clock-frequency : frequency of bus clock in Hz; see the note below.
+                    Defaults to 100 KHz when the property is not specified
 - reg-shift       : device register offsets are shifted by this value
 - reg-io-width    : io register width in bytes (1, 2 or 4)
 - regstep         : deprecated, use reg-shift above
 
-Example:
+Note
+clock-frequency property is meant to control the bus frequency for i2c bus
+drivers, but it was incorrectly used to specify i2c controller input clock
+frequency. So the following rules are set to fix this situation:
+- if clock-frequency is present and neither opencores,ip-clock-frequency nor
+  clocks are, then clock-frequency specifies i2c controller clock frequency.
+  This is to keep backwards compatibility with setups using old DTB. i2c bus
+  frequency is fixed at 100 KHz.
+- if clocks is present it specifies i2c controller clock. clock-frequency
+  property specifies i2c bus frequency.
+- if opencores,ip-clock-frequency is present it specifies i2c controller
+  clock frequency. clock-frequency property specifies i2c bus frequency.
 
+Examples:
+
+	i2c0: ocores@a0000000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "opencores,i2c-ocores";
+		reg = <0xa0000000 0x8>;
+		interrupts = <10>;
+		opencores,ip-clock-frequency = <20000000>;
+
+		reg-shift = <0>;	/* 8 bit registers */
+		reg-io-width = <1>;	/* 8 bit read/write */
+
+		dummy@60 {
+			compatible = "dummy";
+			reg = <0x60>;
+		};
+	};
+or
 	i2c0: ocores@a0000000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "opencores,i2c-ocores";
 		reg = <0xa0000000 0x8>;
 		interrupts = <10>;
-		clock-frequency = <20000000>;
+		clocks = <&osc>;
+		clock-frequency = <400000>; /* i2c bus frequency 400 KHz */
 
 		reg-shift = <0>;	/* 8 bit registers */
 		reg-io-width = <1>;	/* 8 bit read/write */
diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt
index dde6c22ce91a..f0d71bc52e64 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt
@@ -21,6 +21,17 @@ Required on RK3066, RK3188 :
 Optional properties :
 
  - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used.
+ - i2c-scl-rising-time-ns : Number of nanoseconds the SCL signal takes to rise
+	(t(r) in I2C specification). If not specified this is assumed to be
+	the maximum the specification allows(1000 ns for Standard-mode,
+	300 ns for Fast-mode) which might cause slightly slower communication.
+ - i2c-scl-falling-time-ns : Number of nanoseconds the SCL signal takes to fall
+	(t(f) in the I2C specification). If not specified this is assumed to
+	be the maximum the specification allows (300 ns) which might cause
+	slightly slower communication.
+ - i2c-sda-falling-time-ns : Number of nanoseconds the SDA signal takes to fall
+	(t(f) in the I2C specification). If not specified we'll use the SCL
+	value since they are the same in nearly all cases.
 
 Example:
 
@@ -39,4 +50,7 @@ i2c0: i2c@2002d000 {
 
 	clock-names = "i2c";
 	clocks = <&cru PCLK_I2C0>;
+
+	i2c-scl-rising-time-ns = <800>;
+	i2c-scl-falling-time-ns = <100>;
 };
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 4dcd88d5f7ca..aaa8325004d2 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -61,9 +61,8 @@ fsl,sgtl5000		SGTL5000: Ultra Low-Power Audio Codec
 gmt,g751		G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface
 infineon,slb9635tt	Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz)
 infineon,slb9645tt	Infineon SLB9645 I2C TPM (new protocol, max 400khz)
-isl,isl12057		Intersil ISL12057 I2C RTC Chip
-isil,isl29028           (deprecated, use isl)
-isl,isl29028            Intersil ISL29028 Ambient Light and Proximity Sensor
+isil,isl12057		Intersil ISL12057 I2C RTC Chip
+isil,isl29028		Intersil ISL29028 Ambient Light and Proximity Sensor
 maxim,ds1050		5 Bit Programmable, Pulse-Width Modulator
 maxim,max1237		Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs
 maxim,max6625		9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface
diff --git a/Documentation/devicetree/bindings/mfd/da9063.txt b/Documentation/devicetree/bindings/mfd/da9063.txt
new file mode 100644
index 000000000000..42c6fa6f1c9a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/da9063.txt
@@ -0,0 +1,93 @@
+* Dialog DA9063 Power Management Integrated Circuit (PMIC)
+
+DA9093 consists of a large and varied group of sub-devices (I2C Only):
+
+Device                   Supply Names    Description
+------                   ------------    -----------
+da9063-regulator        :               : LDOs & BUCKs
+da9063-rtc              :               : Real-Time Clock
+da9063-watchdog         :               : Watchdog
+
+======
+
+Required properties:
+
+- compatible : Should be "dlg,da9063"
+- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
+  modified to match the chip's OTP settings).
+- interrupt-parent : Specifies the reference to the interrupt controller for
+  the DA9063.
+- interrupts : IRQ line information.
+- interrupt-controller
+
+Sub-nodes:
+
+- regulators : This node defines the settings for the LDOs and BUCKs. The
+  DA9063 regulators are bound using their names listed below:
+
+    bcore1    : BUCK CORE1
+    bcore2    : BUCK CORE2
+    bpro      : BUCK PRO
+    bmem      : BUCK MEM
+    bio       : BUCK IO
+    bperi     : BUCK PERI
+    ldo1      : LDO_1
+    ldo2      : LDO_2
+    ldo3      : LDO_3
+    ldo4      : LDO_4
+    ldo5      : LDO_5
+    ldo6      : LDO_6
+    ldo7      : LDO_7
+    ldo8      : LDO_8
+    ldo9      : LDO_9
+    ldo10     : LDO_10
+    ldo11     : LDO_11
+
+  The component follows the standard regulator framework and the bindings
+  details of individual regulator device can be found in:
+  Documentation/devicetree/bindings/regulator/regulator.txt
+
+- rtc : This node defines settings for the Real-Time Clock associated with
+  the DA9063. There are currently no entries in this binding, however
+  compatible = "dlg,da9063-rtc" should be added if a node is created.
+
+- watchdog : This node defines settings for the Watchdog timer associated
+  with the DA9063. There are currently no entries in this binding, however
+  compatible = "dlg,da9063-watchdog" should be added if a node is created.
+
+
+Example:
+
+	pmic0: da9063@58 {
+		compatible = "dlg,da9063"
+		reg = <0x58>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+
+		rtc {
+			compatible = "dlg,da9063-rtc";
+		};
+
+		wdt {
+			compatible = "dlg,da9063-watchdog";
+		};
+
+		regulators {
+			DA9063_BCORE1: bcore1 {
+				regulator-name = "BCORE1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1570000>;
+				regulator-min-microamp = <500000>;
+				regulator-max-microamp = <2000000>;
+				regulator-boot-on;
+			};
+			DA9063_LDO11: ldo11 {
+				regulator-name = "LDO_11";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-boot-on;
+			};
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
new file mode 100644
index 000000000000..85e31980017a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
@@ -0,0 +1,70 @@
+Qualcomm Resource Power Manager (RPM)
+
+This driver is used to interface with the Resource Power Manager (RPM) found in
+various Qualcomm platforms. The RPM allows each component in the system to vote
+for state of the system resources, such as clocks, regulators and bus
+frequencies.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,rpm-apq8064"
+		    "qcom,rpm-msm8660"
+		    "qcom,rpm-msm8960"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: base address and size of the RPM's message ram
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: three entries specifying the RPM's:
+		    1. acknowledgement interrupt
+		    2. error interrupt
+		    3. wakeup interrupt
+
+- interrupt-names:
+	Usage: required
+	Value type: <string-array>
+	Definition: must be the three strings "ack", "err" and "wakeup", in order
+
+- #address-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 1
+
+- #size-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 0
+
+- qcom,ipc:
+	Usage: required
+	Value type: <prop-encoded-array>
+
+	Definition: three entries specifying the outgoing ipc bit used for
+		    signaling the RPM:
+		    - phandle to a syscon node representing the apcs registers
+		    - u32 representing offset to the register within the syscon
+		    - u32 representing the ipc bit within the register
+
+
+= EXAMPLE
+
+	#include <dt-bindings/mfd/qcom-rpm.h>
+
+	rpm@108000 {
+		compatible = "qcom,rpm-msm8960";
+		reg = <0x108000 0x1000>;
+		qcom,ipc = <&apcs 0x8 2>;
+
+		interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
+		interrupt-names = "ack", "err", "wakeup";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
diff --git a/Documentation/devicetree/bindings/mips/cavium/cib.txt b/Documentation/devicetree/bindings/mips/cavium/cib.txt
new file mode 100644
index 000000000000..f39a1aa2852b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mips/cavium/cib.txt
@@ -0,0 +1,43 @@
+* Cavium Interrupt Bus widget
+
+Properties:
+- compatible: "cavium,octeon-7130-cib"
+
+  Compatibility with cn70XX SoCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: Two elements consisting of the addresses of the RAW and EN
+  registers of the CIB block
+
+- cavium,max-bits: The index (zero based) of the highest numbered bit
+  in the CIB block.
+
+- interrupt-parent:  Always the CIU on the SoC.
+
+- interrupts: The CIU line to which the CIB block is connected.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bit within the
+   CIB.  The second cell specifies the triggering semantics of the
+   line.
+
+Example:
+
+	interrupt-controller@107000000e000 {
+		compatible = "cavium,octeon-7130-cib";
+		reg = <0x10700 0x0000e000 0x0 0x8>, /* RAW */
+		      <0x10700 0x0000e100 0x0 0x8>; /* EN */
+		cavium,max-bits = <23>;
+
+		interrupt-controller;
+		interrupt-parent = <&ciu>;
+		interrupts = <1 24>;
+		/* Interrupts are specified by two parts:
+		 * 1) Bit number in the CIB* registers
+		 * 2) Triggering (1 - edge rising
+		 *		  2 - edge falling
+		 *		  4 - level active high
+		 *		  8 - level active low)
+		 */
+		#interrupt-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
index 91b3a3467150..4bf41d833804 100644
--- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
@@ -10,8 +10,8 @@ Absolute maximum transfer rate is 200MB/s
 Required properties:
  - compatible : "allwinner,sun4i-a10-mmc" or "allwinner,sun5i-a13-mmc"
  - reg : mmc controller base registers
- - clocks : a list with 2 phandle + clock specifier pairs
- - clock-names : must contain "ahb" and "mmc"
+ - clocks : a list with 4 phandle + clock specifier pairs
+ - clock-names : must contain "ahb", "mmc", "output" and "sample"
  - interrupts : mmc controller interrupt
 
 Optional properties:
@@ -25,8 +25,8 @@ Examples:
 	mmc0: mmc@01c0f000 {
 		compatible = "allwinner,sun5i-a13-mmc";
 		reg = <0x01c0f000 0x1000>;
-		clocks = <&ahb_gates 8>, <&mmc0_clk>;
-		clock-names = "ahb", "mod";
+		clocks = <&ahb_gates 8>, <&mmc0_clk>, <&mmc0_output_clk>, <&mmc0_sample_clk>;
+		clock-names = "ahb", "mod", "output", "sample";
 		interrupts = <0 32 4>;
 		status = "disabled";
 	};
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
index 1fe6dde98499..7d4c8eb775a5 100644
--- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -1,7 +1,7 @@
 Atmel NAND flash
 
 Required properties:
-- compatible : "atmel,at91rm9200-nand".
+- compatible : should be "atmel,at91rm9200-nand" or "atmel,sama5d4-nand".
 - reg : should specify localbus address and size used for the chip,
 	and hardware ECC controller if available.
 	If the hardware ECC is PMECC, it should contain address and size for
diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
index 823d13412195..4461dc71cb10 100644
--- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
+++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
@@ -1,7 +1,7 @@
 * Freescale Quad Serial Peripheral Interface(QuadSPI)
 
 Required properties:
-  - compatible : Should be "fsl,vf610-qspi"
+  - compatible : Should be "fsl,vf610-qspi" or "fsl,imx6sx-qspi"
   - reg : the first contains the register location and length,
           the second contains the memory mapping address and length
   - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
index a011fdf61dbf..d02acaff3c35 100644
--- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
@@ -1,7 +1,7 @@
 * Freescale General-Purpose Media Interface (GPMI)
 
 The GPMI nand controller provides an interface to control the
-NAND flash chips. We support only one NAND chip now.
+NAND flash chips.
 
 Required properties:
   - compatible : should be "fsl,<chip>-gpmi-nand"
diff --git a/Documentation/devicetree/bindings/mtd/hisi504-nand.txt b/Documentation/devicetree/bindings/mtd/hisi504-nand.txt
new file mode 100644
index 000000000000..2e35f0662912
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/hisi504-nand.txt
@@ -0,0 +1,47 @@
+Hisilicon Hip04 Soc NAND controller DT binding
+
+Required properties:
+
+- compatible:          Should be "hisilicon,504-nfc".
+- reg:                 The first contains base physical address and size of
+                       NAND controller's registers. The second contains base
+                       physical address and size of NAND controller's buffer.
+- interrupts:          Interrupt number for nfc.
+- nand-bus-width:      See nand.txt.
+- nand-ecc-mode:       Support none and hw ecc mode.
+- #address-cells:      Partition address, should be set 1.
+- #size-cells:         Partition size, should be set 1.
+
+Optional properties:
+
+- nand-ecc-strength:   Number of bits to correct per ECC step.
+- nand-ecc-step-size:  Number of data bytes covered by a single ECC step.
+
+The following ECC strength and step size are currently supported:
+
+ - nand-ecc-strength = <16>, nand-ecc-step-size = <1024>
+
+Flash chip may optionally contain additional sub-nodes describing partitions of
+the address space. See partition.txt for more detail.
+
+Example:
+
+	nand: nand@4020000 {
+		compatible = "hisilicon,504-nfc";
+		reg = <0x4020000 0x10000>, <0x5000000 0x1000>;
+		interrupts = <0 379 4>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <16>;
+		nand-ecc-step-size = <1024>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "nand_text";
+			reg = <0x00000000 0x00400000>;
+		};
+
+		...
+
+	};
diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
index 6b9f680cb579..4a0a48bf4ecb 100644
--- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
@@ -36,6 +36,11 @@ are defined:
  - vendor-id : Contains the flash chip's vendor id (1 byte).
  - device-id : Contains the flash chip's device id (1 byte).
 
+For ROM compatible devices (and ROM fallback from cfi-flash), the following
+additional (optional) property is defined:
+
+ - erase-size : The chip's physical erase block size in bytes.
+
 The device tree may optionally contain sub-nodes describing partitions of the
 address space. See partition.txt for more detail.
 
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
index 33df3932168e..8db32384a486 100644
--- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
+++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
@@ -27,6 +27,8 @@ property is used.
 - amd,serdes-cdr-rate: CDR rate speed selection
 - amd,serdes-pq-skew: PQ (data sampling) skew
 - amd,serdes-tx-amp: TX amplitude boost
+- amd,serdes-dfe-tap-config: DFE taps available to run
+- amd,serdes-dfe-tap-enable: DFE taps to enable
 
 Example:
 	xgbe_phy@e1240800 {
@@ -41,4 +43,6 @@ Example:
 		amd,serdes-cdr-rate = <2>, <2>, <7>;
 		amd,serdes-pq-skew = <10>, <10>, <30>;
 		amd,serdes-tx-amp = <15>, <15>, <10>;
+		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
+		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
 	};
diff --git a/Documentation/devicetree/bindings/pwm/img-pwm.txt b/Documentation/devicetree/bindings/pwm/img-pwm.txt
new file mode 100644
index 000000000000..fade5f26fcac
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/img-pwm.txt
@@ -0,0 +1,24 @@
+*Imagination Technologies PWM DAC driver
+
+Required properties:
+  - compatible: Should be "img,pistachio-pwm"
+  - reg: Should contain physical base address and length of pwm registers.
+  - clocks: Must contain an entry for each entry in clock-names.
+	See ../clock/clock-bindings.txt for details.
+  - clock-names: Must include the following entries.
+    - pwm: PWM operating clock.
+    - sys: PWM system interface clock.
+  - #pwm-cells: Should be 2. See pwm.txt in this directory for the
+	description of the cells format.
+  - img,cr-periph: Must contain a phandle to the peripheral control
+	syscon node which contains PWM control registers.
+
+Example:
+	pwm: pwm@18101300 {
+		compatible = "img,pistachio-pwm";
+		reg = <0x18101300 0x100>;
+		clocks = <&pwm_clk>, <&system_clk>;
+		clock-names = "pwm", "sys";
+		#pwm-cells = <2>;
+		img,cr-periph = <&cr_periph>;
+	};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt
new file mode 100644
index 000000000000..ae0273e19506
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt
@@ -0,0 +1,20 @@
+Allwinner sun4i and sun7i SoC PWM controller
+
+Required properties:
+  - compatible: should be one of:
+    - "allwinner,sun4i-a10-pwm"
+    - "allwinner,sun7i-a20-pwm"
+  - reg: physical base address and length of the controller's registers
+  - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+    the cells format.
+  - clocks: From common clock binding, handle to the parent clock.
+
+Example:
+
+	pwm: pwm@01c20e00 {
+		compatible = "allwinner,sun7i-a20-pwm";
+		reg = <0x01c20e00 0xc>;
+		clocks = <&osc24M>;
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
diff --git a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt
index ae738f562acc..695150a4136b 100644
--- a/Documentation/devicetree/bindings/thermal/exynos-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/exynos-thermal.txt
@@ -12,6 +12,7 @@
 	       "samsung,exynos5420-tmu-ext-triminfo" for TMU channels 2, 3 and 4
 			Exynos5420 (Must pass triminfo base and triminfo clock)
 	       "samsung,exynos5440-tmu"
+	       "samsung,exynos7-tmu"
 - interrupt-parent : The phandle for the interrupt controller
 - reg : Address range of the thermal registers. For soc's which has multiple
 	instances of TMU and some registers are shared across all TMU's like
@@ -32,13 +33,28 @@
 - clocks : The main clocks for TMU device
 	-- 1. operational clock for TMU channel
 	-- 2. optional clock to access the shared registers of TMU channel
+	-- 3. optional special clock for functional operation
 - clock-names : Thermal system clock name
 	-- "tmu_apbif" operational clock for current TMU channel
 	-- "tmu_triminfo_apbif" clock to access the shared triminfo register
 		for current TMU channel
+	-- "tmu_sclk" clock for functional operation of the current TMU
+		channel
 - vtmu-supply: This entry is optional and provides the regulator node supplying
 		voltage to TMU. If needed this entry can be placed inside
 		board/platform specific dts file.
+Following properties are mandatory (depending on SoC):
+- samsung,tmu_gain: Gain value for internal TMU operation.
+- samsung,tmu_reference_voltage: Value of TMU IP block's reference voltage
+- samsung,tmu_noise_cancel_mode: Mode for noise cancellation
+- samsung,tmu_efuse_value: Default level of temperature - it is needed when
+			   in factory fusing produced wrong value
+- samsung,tmu_min_efuse_value: Minimum temperature fused value
+- samsung,tmu_max_efuse_value: Maximum temperature fused value
+- samsung,tmu_first_point_trim: First point trimming value
+- samsung,tmu_second_point_trim: Second point trimming value
+- samsung,tmu_default_temp_offset: Default temperature offset
+- samsung,tmu_cal_type: Callibration type
 
 Example 1):
 
@@ -51,6 +67,7 @@ Example 1):
 		clock-names = "tmu_apbif";
 		status = "disabled";
 		vtmu-supply = <&tmu_regulator_node>;
+		#include "exynos4412-tmu-sensor-conf.dtsi"
 	};
 
 Example 2):
@@ -61,6 +78,7 @@ Example 2):
 		interrupts = <0 58 0>;
 		clocks = <&clock 21>;
 		clock-names = "tmu_apbif";
+		#include "exynos5440-tmu-sensor-conf.dtsi"
 	};
 
 Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register")
@@ -70,6 +88,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register")
 		interrupts = <0 184 0>;
 		clocks = <&clock 318>, <&clock 318>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+		#include "exynos4412-tmu-sensor-conf.dtsi"
 	};
 
 	tmu_cpu3: tmu@1006c000 {
@@ -78,6 +97,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register")
 		interrupts = <0 185 0>;
 		clocks = <&clock 318>, <&clock 319>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+		#include "exynos4412-tmu-sensor-conf.dtsi"
 	};
 
 	tmu_gpu: tmu@100a0000 {
@@ -86,6 +106,7 @@ Example 3): (In case of Exynos5420 "with misplaced TRIMINFO register")
 		interrupts = <0 215 0>;
 		clocks = <&clock 319>, <&clock 318>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+		#include "exynos4412-tmu-sensor-conf.dtsi"
 	};
 
 Note: For multi-instance tmu each instance should have an alias correctly
diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt
index f5db6b72a36f..29fe0bfae38e 100644
--- a/Documentation/devicetree/bindings/thermal/thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/thermal.txt
@@ -251,24 +251,24 @@ ocp {
 };
 
 thermal-zones {
-	cpu-thermal: cpu-thermal {
+	cpu_thermal: cpu-thermal {
 		polling-delay-passive = <250>; /* milliseconds */
 		polling-delay = <1000>; /* milliseconds */
 
 		thermal-sensors = <&bandgap0>;
 
 		trips {
-			cpu-alert0: cpu-alert {
+			cpu_alert0: cpu-alert0 {
 				temperature = <90000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "active";
 			};
-			cpu-alert1: cpu-alert {
+			cpu_alert1: cpu-alert1 {
 				temperature = <100000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "passive";
 			};
-			cpu-crit: cpu-crit {
+			cpu_crit: cpu-crit {
 				temperature = <125000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "critical";
@@ -277,17 +277,17 @@ thermal-zones {
 
 		cooling-maps {
 			map0 {
-				trip = <&cpu-alert0>;
-				cooling-device = <&fan0 THERMAL_NO_LIMITS 4>;
+				trip = <&cpu_alert0>;
+				cooling-device = <&fan0 THERMAL_NO_LIMIT 4>;
 			};
 			map1 {
-				trip = <&cpu-alert1>;
-				cooling-device = <&fan0 5 THERMAL_NO_LIMITS>;
+				trip = <&cpu_alert1>;
+				cooling-device = <&fan0 5 THERMAL_NO_LIMIT>;
 			};
 			map2 {
-				trip = <&cpu-alert1>;
+				trip = <&cpu_alert1>;
 				cooling-device =
-				    <&cpu0 THERMAL_NO_LIMITS THERMAL_NO_LIMITS>;
+				    <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
 			};
 		};
 	};
@@ -298,13 +298,13 @@ used to monitor the zone 'cpu-thermal' using its sole sensor. A fan
 device (fan0) is controlled via I2C bus 1, at address 0x48, and has ten
 different cooling states 0-9. It is used to remove the heat out of
 the thermal zone 'cpu-thermal' using its cooling states
-from its minimum to 4, when it reaches trip point 'cpu-alert0'
+from its minimum to 4, when it reaches trip point 'cpu_alert0'
 at 90C, as an example of active cooling. The same cooling device is used at
-'cpu-alert1', but from 5 to its maximum state. The cpu@0 device is also
+'cpu_alert1', but from 5 to its maximum state. The cpu@0 device is also
 linked to the same thermal zone, 'cpu-thermal', as a passive cooling device,
-using all its cooling states at trip point 'cpu-alert1',
+using all its cooling states at trip point 'cpu_alert1',
 which is a trip point at 100C. On the thermal zone 'cpu-thermal', at the
-temperature of 125C, represented by the trip point 'cpu-crit', the silicon
+temperature of 125C, represented by the trip point 'cpu_crit', the silicon
 is not reliable anymore.
 
 (b) - IC with several internal sensors
@@ -329,7 +329,7 @@ ocp {
 };
 
 thermal-zones {
-	cpu-thermal: cpu-thermal {
+	cpu_thermal: cpu-thermal {
 		polling-delay-passive = <250>; /* milliseconds */
 		polling-delay = <1000>; /* milliseconds */
 
@@ -338,12 +338,12 @@ thermal-zones {
 
 		trips {
 			/* each zone within the SoC may have its own trips */
-			cpu-alert: cpu-alert {
+			cpu_alert: cpu-alert {
 				temperature = <100000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "passive";
 			};
-			cpu-crit: cpu-crit {
+			cpu_crit: cpu-crit {
 				temperature = <125000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "critical";
@@ -356,7 +356,7 @@ thermal-zones {
 		};
 	};
 
-	gpu-thermal: gpu-thermal {
+	gpu_thermal: gpu-thermal {
 		polling-delay-passive = <120>; /* milliseconds */
 		polling-delay = <1000>; /* milliseconds */
 
@@ -365,12 +365,12 @@ thermal-zones {
 
 		trips {
 			/* each zone within the SoC may have its own trips */
-			gpu-alert: gpu-alert {
+			gpu_alert: gpu-alert {
 				temperature = <90000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "passive";
 			};
-			gpu-crit: gpu-crit {
+			gpu_crit: gpu-crit {
 				temperature = <105000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "critical";
@@ -383,7 +383,7 @@ thermal-zones {
 		};
 	};
 
-	dsp-thermal: dsp-thermal {
+	dsp_thermal: dsp-thermal {
 		polling-delay-passive = <50>; /* milliseconds */
 		polling-delay = <1000>; /* milliseconds */
 
@@ -392,12 +392,12 @@ thermal-zones {
 
 		trips {
 			/* each zone within the SoC may have its own trips */
-			dsp-alert: gpu-alert {
+			dsp_alert: dsp-alert {
 				temperature = <90000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "passive";
 			};
-			dsp-crit: gpu-crit {
+			dsp_crit: gpu-crit {
 				temperature = <135000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "critical";
@@ -457,7 +457,7 @@ ocp {
 };
 
 thermal-zones {
-	cpu-thermal: cpu-thermal {
+	cpu_thermal: cpu-thermal {
 		polling-delay-passive = <250>; /* milliseconds */
 		polling-delay = <1000>; /* milliseconds */
 
@@ -508,7 +508,7 @@ with many sensors and many cooling devices.
 	/*
 	 * An IC with several temperature sensor.
 	 */
-	adc-dummy: sensor@0x50 {
+	adc_dummy: sensor@0x50 {
 		...
 		#thermal-sensor-cells = <1>; /* sensor internal ID */
 	};
@@ -520,7 +520,7 @@ thermal-zones {
 		polling-delay = <2500>; /* milliseconds */
 
 				/* sensor       ID */
-		thermal-sensors = <&adc-dummy     4>;
+		thermal-sensors = <&adc_dummy     4>;
 
 		trips {
 			...
@@ -531,14 +531,14 @@ thermal-zones {
 		};
 	};
 
-	board-thermal: board-thermal {
+	board_thermal: board-thermal {
 		polling-delay-passive = <1000>; /* milliseconds */
 		polling-delay = <2500>; /* milliseconds */
 
 				/* sensor       ID */
-		thermal-sensors = <&adc-dummy     0>, /* pcb top edge */
-				  <&adc-dummy     1>, /* lcd */
-				  <&adc-dymmy     2>; /* back cover */
+		thermal-sensors = <&adc_dummy     0>, /* pcb top edge */
+				  <&adc_dummy     1>, /* lcd */
+				  <&adc_dummy     2>; /* back cover */
 		/*
 		 * An array of coefficients describing the sensor
 		 * linear relation. E.g.:
@@ -548,22 +548,22 @@ thermal-zones {
 
 		trips {
 			/* Trips are based on resulting linear equation */
-			cpu-trip: cpu-trip {
+			cpu_trip: cpu-trip {
 				temperature = <60000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "passive";
 			};
-			gpu-trip: gpu-trip {
+			gpu_trip: gpu-trip {
 				temperature = <55000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "passive";
 			}
-			lcd-trip: lcp-trip {
+			lcd_trip: lcp-trip {
 				temperature = <53000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "passive";
 			};
-			crit-trip: crit-trip {
+			crit_trip: crit-trip {
 				temperature = <68000>; /* millicelsius */
 				hysteresis = <2000>; /* millicelsius */
 				type = "critical";
@@ -572,17 +572,17 @@ thermal-zones {
 
 		cooling-maps {
 			map0 {
-				trip = <&cpu-trip>;
+				trip = <&cpu_trip>;
 				cooling-device = <&cpu0 0 2>;
 				contribution = <55>;
 			};
 			map1 {
-				trip = <&gpu-trip>;
+				trip = <&gpu_trip>;
 				cooling-device = <&gpu0 0 2>;
 				contribution = <20>;
 			};
 			map2 {
-				trip = <&lcd-trip>;
+				trip = <&lcd_trip>;
 				cooling-device = <&lcd0 5 10>;
 				contribution = <15>;
 			};
diff --git a/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt b/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt
index 37afec194949..198794963786 100644
--- a/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt
@@ -13,6 +13,11 @@ Required Properties:
     by the GPIO flags.
 - hw_margin_ms: Maximum time to reset watchdog circuit (milliseconds).
 
+Optional Properties:
+- always-running: If the watchdog timer cannot be disabled, add this flag to
+  have the driver keep toggling the signal without a client. It will only cease
+  to toggle the signal when the device is open and the timeout elapsed.
+
 Example:
 	watchdog: watchdog {
 		/* ADM706 */
diff --git a/Documentation/devicetree/bindings/watchdog/imgpdc-wdt.txt b/Documentation/devicetree/bindings/watchdog/imgpdc-wdt.txt
new file mode 100644
index 000000000000..b2fa11fd43de
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/imgpdc-wdt.txt
@@ -0,0 +1,19 @@
+*ImgTec PowerDown Controller (PDC) Watchdog Timer (WDT)
+
+Required properties:
+- compatible : Should be "img,pdc-wdt"
+- reg : Should contain WDT registers location and length
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Should contain "wdt" and "sys"; the watchdog counter
+               clock and register interface clock respectively.
+- interrupts : Should contain WDT interrupt
+
+Examples:
+
+watchdog@18102100 {
+	compatible = "img,pdc-wdt";
+	reg = <0x18102100 0x100>;
+	clocks = <&pdc_wdt_clk>, <&sys_clk>;
+	clock-names = "wdt", "sys";
+	interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt
new file mode 100644
index 000000000000..e27763ef0049
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt
@@ -0,0 +1,12 @@
+Ingenic Watchdog Timer (WDT) Controller for JZ4740
+
+Required properties:
+compatible: "ingenic,jz4740-watchdog"
+reg: Register address and length for watchdog registers
+
+Example:
+
+watchdog: jz4740-watchdog@0x10002000 {
+	compatible = "ingenic,jz4740-watchdog";
+	reg = <0x10002000 0x100>;
+};
diff --git a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
new file mode 100644
index 000000000000..af9eb5b8a253
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
@@ -0,0 +1,13 @@
+Mediatek SoCs Watchdog timer
+
+Required properties:
+
+- compatible : should be "mediatek,mt6589-wdt"
+- reg : Specifies base physical address and size of the registers.
+
+Example:
+
+wdt: watchdog@010000000 {
+	compatible = "mediatek,mt6589-wdt";
+	reg = <0x10000000 0x18>;
+};