ARM: Remove mach-msm and associated ARM architecture code

The maintainers for mach-msm no longer have any plans to support
or test the platforms supported by this architecture[1]. Most likely
there aren't any active users of this code anyway, so let's
delete it.

[1] http://lkml.kernel.org/r/20150307031212.GA8434@fifo99.com
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>

2 files changed, 0 insertions, 178 deletions

diff --git a/Documentation/arm/00-INDEX b/Documentation/arm/00-INDEX
index 8edb9007844e..dea011c8d7c7 100644
--- a/Documentation/arm/00-INDEX
+++ b/Documentation/arm/00-INDEX
@@ -10,8 +10,6 @@ IXP4xx
 	- Intel IXP4xx Network processor.
 Makefile
 	- Build sourcefiles as part of the Documentation-build for arm
-msm/
-	- MSM specific documentation
 Netwinder
 	- Netwinder specific documentation
 Porting
diff --git a/Documentation/arm/msm/gpiomux.txt b/Documentation/arm/msm/gpiomux.txt
deleted file mode 100644
index 67a81620adf6..000000000000
--- a/Documentation/arm/msm/gpiomux.txt
+++ /dev/null
@@ -1,176 +0,0 @@
-This document provides an overview of the msm_gpiomux interface, which
-is used to provide gpio pin multiplexing and configuration on mach-msm
-targets.
-
-History
-=======
-
-The first-generation API for gpio configuration & multiplexing on msm
-is the function gpio_tlmm_config().  This function has a few notable
-shortcomings, which led to its deprecation and replacement by gpiomux:
-
-The 'disable' parameter:  Setting the second parameter to
-gpio_tlmm_config to GPIO_CFG_DISABLE tells the peripheral
-processor in charge of the subsystem to perform a look-up into a
-low-power table and apply the low-power/sleep setting for the pin.
-As the msm family evolved this became problematic. Not all pins
-have sleep settings, not all peripheral processors will accept requests
-to apply said sleep settings, and not all msm targets have their gpio
-subsystems managed by a peripheral processor. In order to get consistent
-behavior on all targets, drivers are forced to ignore this parameter,
-rendering it useless.
-
-The 'direction' flag: for all mux-settings other than raw-gpio (0),
-the output-enable bit of a gpio is hard-wired to a known
-input (usually VDD or ground).  For those settings, the direction flag
-is meaningless at best, and deceptive at worst.  In addition, using the
-direction flag to change output-enable (OE) directly can cause trouble in
-gpiolib, which has no visibility into gpio direction changes made
-in this way.  Direction control in gpio mode should be made through gpiolib.
-
-Key Features of gpiomux
-=======================
-
-- A consistent interface across all generations of msm.  Drivers can expect
-the same results on every target.
-- gpiomux plays nicely with gpiolib.  Functions that should belong to gpiolib
-are left to gpiolib and not duplicated here.  gpiomux is written with the
-intent that gpio_chips will call gpiomux reference-counting methods
-from their request() and free() hooks, providing full integration.
-- Tabular configuration.  Instead of having to call gpio_tlmm_config
-hundreds of times, gpio configuration is placed in a single table.
-- Per-gpio sleep.  Each gpio is individually reference counted, allowing only
-those lines which are in use to be put in high-power states.
-- 0 means 'do nothing': all flags are designed so that the default memset-zero
-equates to a sensible default of 'no configuration', preventing users
-from having to provide hundreds of 'no-op' configs for unused or
-unwanted lines.
-
-Usage
-=====
-
-To use gpiomux, provide configuration information for relevant gpio lines
-in the msm_gpiomux_configs table.  Since a 0 equates to "unconfigured",
-only those lines to be managed by gpiomux need to be specified.  Here
-is a completely fictional example:
-
-struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = {
-	[12] = {
-		.active = GPIOMUX_VALID | GPIOMUX_DRV_8MA | GPIOMUX_FUNC_1,
-		.suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN,
-	},
-	[34] = {
-		.suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN,
-	},
-};
-
-To indicate that a gpio is in use, call msm_gpiomux_get() to increase
-its reference count.  To decrease the reference count, call msm_gpiomux_put().
-
-The effect of this configuration is as follows:
-
-When the system boots, gpios 12 and 34 will be initialized with their
-'suspended' configurations.  All other gpios, which were left unconfigured,
-will not be touched.
-
-When msm_gpiomux_get() is called on gpio 12 to raise its reference count
-above 0, its active configuration will be applied.  Since no other gpio
-line has a valid active configuration, msm_gpiomux_get() will have no
-effect on any other line.
-
-When msm_gpiomux_put() is called on gpio 12 or 34 to drop their reference
-count to 0, their suspended configurations will be applied.
-Since no other gpio line has a valid suspended configuration, no other
-gpio line will be effected by msm_gpiomux_put().  Since gpio 34 has no valid
-active configuration, this is effectively a no-op for gpio 34 as well,
-with one small caveat, see the section "About Output-Enable Settings".
-
-All of the GPIOMUX_VALID flags may seem like unnecessary overhead, but
-they address some important issues.  As unused entries (all those
-except 12 and 34) are zero-filled, gpiomux needs a way to distinguish
-the used fields from the unused.  In addition, the all-zero pattern
-is a valid configuration!  Therefore, gpiomux defines an additional bit
-which is used to indicate when a field is used.  This has the pleasant
-side-effect of allowing calls to msm_gpiomux_write to use '0' to indicate
-that a value should not be changed:
-
-  msm_gpiomux_write(0, GPIOMUX_VALID, 0);
-
-replaces the active configuration of gpio 0 with an all-zero configuration,
-but leaves the suspended configuration as it was.
-
-Static Configurations
-=====================
-
-To install a static configuration, which is applied at boot and does
-not change after that, install a configuration with a suspended component
-but no active component, as in the previous example:
-
-	[34] = {
-		.suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN,
-	},
-
-The suspended setting is applied during boot, and the lack of any valid
-active setting prevents any other setting from being applied at runtime.
-If other subsystems attempting to access the line is a concern, one could
-*really* anchor the configuration down by calling msm_gpiomux_get on the
-line at initialization to move the line into active mode.  With the line
-held, it will never be re-suspended, and with no valid active configuration,
-no new configurations will be applied.
-
-But then, if having other subsystems grabbing for the line is truly a concern,
-it should be reserved with gpio_request instead, which carries an implicit
-msm_gpiomux_get.
-
-gpiomux and gpiolib
-===================
-
-It is expected that msm gpio_chips will call msm_gpiomux_get() and
-msm_gpiomux_put() from their request and free hooks, like this fictional
-example:
-
-static int request(struct gpio_chip *chip, unsigned offset)
-{
-        return msm_gpiomux_get(chip->base + offset);
-}
-
-static void free(struct gpio_chip *chip, unsigned offset)
-{
-        msm_gpiomux_put(chip->base + offset);
-}
-
-	...somewhere in a gpio_chip declaration...
-	.request = request,
-	.free    = free,
-
-This provides important functionality:
-- It guarantees that a gpio line will have its 'active' config applied
-  when the line is requested, and will not be suspended while the line
-  remains requested; and
-- It guarantees that gpio-direction settings from gpiolib behave sensibly.
-  See "About Output-Enable Settings."
-
-This mechanism allows for "auto-request" of gpiomux lines via gpiolib
-when it is suitable.  Drivers wishing more exact control are, of course,
-free to also use msm_gpiomux_set and msm_gpiomux_get.
-
-About Output-Enable Settings
-============================
-
-Some msm targets do not have the ability to query the current gpio
-configuration setting.  This means that changes made to the output-enable
-(OE) bit by gpiolib cannot be consistently detected and preserved by gpiomux.
-Therefore, when gpiomux applies a configuration setting, any direction
-settings which may have been applied by gpiolib are lost and the default
-input settings are re-applied.
-
-For this reason, drivers should not assume that gpio direction settings
-continue to hold if they free and then re-request a gpio.  This seems like
-common sense - after all, anybody could have obtained the line in the
-meantime - but it needs saying.
-
-This also means that calls to msm_gpiomux_write will reset the OE bit,
-which means that if the gpio line is held by a client of gpiolib and
-msm_gpiomux_write is called, the direction setting has been lost and
-gpiolib's internal state has been broken.
-Release gpio lines before reconfiguring them.