1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
|
Device-Tree bindings for Samsung SoC display controller (FIMD)
FIMD (Fully Interactive Mobile Display) is the Display Controller for the
Samsung series of SoCs which transfers the image data from a video memory
buffer to an external LCD interface.
Required properties:
- compatible: value should be one of the following
"samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
"samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
"samsung,s5p6440-fimd"; /* for S5P64X0 SoCs */
"samsung,s5pc100-fimd"; /* for S5PC100 SoC */
"samsung,s5pv210-fimd"; /* for S5PV210 SoC */
"samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
"samsung,exynos5250-fimd"; /* for Exynos5 SoCs */
- reg: physical base address and length of the FIMD registers set.
- interrupt-parent: should be the phandle of the fimd controller's
parent interrupt controller.
- interrupts: should contain a list of all FIMD IP block interrupts in the
order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
format depends on the interrupt controller used.
- interrupt-names: should contain the interrupt names: "fifo", "vsync",
"lcd_sys", in the same order as they were listed in the interrupts
property.
- pinctrl-0: pin control group to be used for this controller.
- pinctrl-names: must contain a "default" entry.
- clocks: must include clock specifiers corresponding to entries in the
clock-names property.
- clock-names: list of clock names sorted in the same order as the clocks
property. Must contain "sclk_fimd" and "fimd".
Optional Properties:
- samsung,power-domain: a phandle to FIMD power domain node.
- display-timings: timing settings for FIMD, as described in document [1].
Can be used in case timings cannot be provided otherwise
or to override timings provided by the panel.
- samsung,sysreg: handle to syscon used to control the system registers
- i80-if-timings: timing configuration for lcd i80 interface support.
- cs-setup: clock cycles for the active period of address signal is enabled
until chip select is enabled.
If not specified, the default value(0) will be used.
- wr-setup: clock cycles for the active period of CS signal is enabled until
write signal is enabled.
If not specified, the default value(0) will be used.
- wr-active: clock cycles for the active period of CS is enabled.
If not specified, the default value(1) will be used.
- wr-hold: clock cycles for the active period of CS is disabled until write
signal is disabled.
If not specified, the default value(0) will be used.
The parameters are defined as:
VCLK(internal) __|¯¯¯¯¯¯|_____|¯¯¯¯¯¯|_____|¯¯¯¯¯¯|_____|¯¯¯¯¯¯|_____|¯¯
: : : : :
Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
| cs-setup+1 | : : :
|<---------->| : : :
Chip Select ¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯|____________:____________:____________|¯¯
| wr-setup+1 | | wr-hold+1 |
|<---------->| |<---------->|
Write Enable ¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯|____________|¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯
| wr-active+1|
|<---------->|
Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
The device node can contain 'port' child nodes according to the bindings defined
in [2]. The following are properties specific to those nodes:
- reg: (required) port index, can be:
0 - for CAMIF0 input,
1 - for CAMIF1 input,
2 - for CAMIF2 input,
3 - for parallel output,
4 - for write-back interface
[1]: Documentation/devicetree/bindings/video/display-timing.txt
[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
Example:
SoC specific DT entry:
fimd@11c00000 {
compatible = "samsung,exynos4210-fimd";
interrupt-parent = <&combiner>;
reg = <0x11c00000 0x20000>;
interrupt-names = "fifo", "vsync", "lcd_sys";
interrupts = <11 0>, <11 1>, <11 2>;
clocks = <&clock 140>, <&clock 283>;
clock-names = "sclk_fimd", "fimd";
samsung,power-domain = <&pd_lcd0>;
status = "disabled";
};
Board specific DT entry:
fimd@11c00000 {
pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
pinctrl-names = "default";
status = "okay";
};
|
