diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/arm/OMAP/DSS | 10 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/video/exynos_dp.txt | 80 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/video/ssd1307fb.txt | 24 |
3 files changed, 108 insertions, 6 deletions
diff --git a/Documentation/arm/OMAP/DSS b/Documentation/arm/OMAP/DSS index a564ceea9e9..4484e021290 100644 --- a/Documentation/arm/OMAP/DSS +++ b/Documentation/arm/OMAP/DSS @@ -285,7 +285,10 @@ FB0 +-- GFX ---- LCD ---- LCD Misc notes ---------- -OMAP FB allocates the framebuffer memory using the OMAP VRAM allocator. +OMAP FB allocates the framebuffer memory using the standard dma allocator. You +can enable Contiguous Memory Allocator (CONFIG_CMA) to improve the dma +allocator, and if CMA is enabled, you use "cma=" kernel parameter to increase +the global memory area for CMA. Using DSI DPLL to generate pixel clock it is possible produce the pixel clock of 86.5MHz (max possible), and with that you get 1280x1024@57 output from DVI. @@ -301,11 +304,6 @@ framebuffer parameters. Kernel boot arguments --------------------- -vram=<size>[,<physaddr>] - - Amount of total VRAM to preallocate and optionally a physical start - memory address. For example, "10M". omapfb allocates memory for - framebuffers from VRAM. - omapfb.mode=<display>:<mode>[,...] - Default video mode for specified displays. For example, "dvi:800x400MR-24@60". See drivers/video/modedb.c. diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt new file mode 100644 index 00000000000..c60da67a5d7 --- /dev/null +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt @@ -0,0 +1,80 @@ +The Exynos display port interface should be configured based on +the type of panel connected to it. + +We use two nodes: + -dp-controller node + -dptx-phy node(defined inside dp-controller node) + +For the DP-PHY initialization, we use the dptx-phy node. +Required properties for dptx-phy: + -reg: + Base address of DP PHY register. + -samsung,enable-mask: + The bit-mask used to enable/disable DP PHY. + +For the Panel initialization, we read data from dp-controller node. +Required properties for dp-controller: + -compatible: + should be "samsung,exynos5-dp". + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + -interrupt-parent: + phandle to Interrupt combiner node. + -samsung,color-space: + input video data format. + COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 + -samsung,dynamic-range: + dynamic range for input video data. + VESA = 0, CEA = 1 + -samsung,ycbcr-coeff: + YCbCr co-efficients for input video. + COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 + -samsung,color-depth: + number of bits per colour component. + COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 + -samsung,link-rate: + link rate supported by the panel. + LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A + -samsung,lane-count: + number of lanes supported by the panel. + LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 + +Optional properties for dp-controller: + -interlaced: + interlace scan mode. + Progressive if defined, Interlaced if not defined + -vsync-active-high: + VSYNC polarity configuration. + High if defined, Low if not defined + -hsync-active-high: + HSYNC polarity configuration. + High if defined, Low if not defined + +Example: + +SOC specific portion: + dp-controller { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x10000>; + interrupts = <10 3>; + interrupt-parent = <&combiner>; + + dptx-phy { + reg = <0x10040720>; + samsung,enable-mask = <1>; + }; + + }; + +Board Specific portion: + dp-controller { + samsung,color-space = <0>; + samsung,dynamic-range = <0>; + samsung,ycbcr-coeff = <0>; + samsung,color-depth = <1>; + samsung,link-rate = <0x0a>; + samsung,lane-count = <4>; + }; diff --git a/Documentation/devicetree/bindings/video/ssd1307fb.txt b/Documentation/devicetree/bindings/video/ssd1307fb.txt new file mode 100644 index 00000000000..3d0060cff06 --- /dev/null +++ b/Documentation/devicetree/bindings/video/ssd1307fb.txt @@ -0,0 +1,24 @@ +* Solomon SSD1307 Framebuffer Driver + +Required properties: + - compatible: Should be "solomon,ssd1307fb-<bus>". The only supported bus for + now is i2c. + - reg: Should contain address of the controller on the I2C bus. Most likely + 0x3c or 0x3d + - pwm: Should contain the pwm to use according to the OF device tree PWM + specification [0] + - reset-gpios: Should contain the GPIO used to reset the OLED display + +Optional properties: + - reset-active-low: Is the reset gpio is active on physical low? + +[0]: Documentation/devicetree/bindings/pwm/pwm.txt + +Examples: +ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7>; + reset-active-low; +}; |