diff options
| -rw-r--r-- | Documentation/hwmon/nct6775 | 81 | ||||
| -rw-r--r-- | drivers/hwmon/Kconfig | 13 | ||||
| -rw-r--r-- | drivers/hwmon/Makefile | 1 | ||||
| -rw-r--r-- | drivers/hwmon/nct6775.c | 1021 |
4 files changed, 1116 insertions, 0 deletions
diff --git a/Documentation/hwmon/nct6775 b/Documentation/hwmon/nct6775 new file mode 100644 index 00000000000..ccfd5cc2100 --- /dev/null +++ b/Documentation/hwmon/nct6775 @@ -0,0 +1,81 @@ +Note +==== + +This driver supersedes the NCT6775F and NCT6776F support in the W83627EHF +driver. + +Kernel driver NCT6775 +===================== + +Supported chips: + * Nuvoton NCT6775F/W83667HG-I + Prefix: 'nct6775' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + * Nuvoton NCT6776F + Prefix: 'nct6776' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + * Nuvoton NCT6779D + Prefix: 'nct6779' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Available from Nuvoton upon request + +Authors: + Guenter Roeck <linux@roeck-us.net> + +Description +----------- + +This driver implements support for the Nuvoton NCT6775F, NCT6776F, and NCT6779D +super I/O chips. + +The chips support up to 25 temperature monitoring sources. Up to 6 of those are +direct temperature sensor inputs, the others are special sources such as PECI, +PCH, and SMBUS. Depending on the chip type, 2 to 6 of the temperature sources +can be monitored and compared against minimum, maximum, and critical +temperatures. The driver reports up to 10 of the temperatures to the user. +There are 4 to 5 fan rotation speed sensors, 8 to 15 analog voltage sensors, +one VID, alarms with beep warnings (control unimplemented), and some automatic +fan regulation strategies (plus manual fan control mode). + +The temperature sensor sources on all chips are configurable. The configured +source for each of the temperature sensors is provided in tempX_label. + +Temperatures are measured in degrees Celsius and measurement resolution is +either 1 degC or 0.5 degC, depending on the temperature source and +configuration. An alarm is triggered when the temperature gets higher than +the high limit; it stays on until the temperature falls below the hysteresis +value. Alarms are only supported for temp1 to temp6, depending on the chip type. + +Fan rotation speeds are reported in RPM (rotations per minute). An alarm is +triggered if the rotation speed has dropped below a programmable limit. On +NCT6775F, fan readings can be divided by a programmable divider (1, 2, 4, 8, +16, 32, 64 or 128) to give the readings more range or accuracy; the other chips +do not have a fan speed divider. The driver sets the most suitable fan divisor +itself; specifically, it doubles the divider value each time a fan speed reading +returns an invalid value. Some fans might not be present because they share pins +with other functions. + +Voltage sensors (also known as IN sensors) report their values in millivolts. +An alarm is triggered if the voltage has crossed a programmable minimum +or maximum limit. + +The driver supports automatic fan control mode known as Thermal Cruise. +In this mode, the chip attempts to keep the measured temperature in a +predefined temperature range. If the temperature goes out of range, fan +is driven slower/faster to reach the predefined range again. + +The mode works for fan1-fan5. + +Usage Notes +----------- + +On various ASUS boards with NCT6776F, it appears that CPUTIN is not really +connected to anything and floats, or that it is connected to some non-standard +temperature measurement device. As a result, the temperature reported on CPUTIN +will not reflect a usable value. It often reports unreasonably high +temperatures, and in some cases the reported temperature declines if the actual +temperature increases (similar to the raw PECI temperature value - see PECI +specification for details). CPUTIN should therefore be be ignored on ASUS +boards. The CPU temperature on ASUS boards is reported from PECI 0. diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 47d2176957a..a0f1d6a406e 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -897,6 +897,19 @@ config SENSORS_MCP3021 This driver can also be built as a module. If so, the module will be called mcp3021. +config SENSORS_NCT6775 + tristate "Nuvoton NCT6775F, NCT6776F, NCT6779D" + depends on !PPC + select HWMON_VID + help + If you say yes here you get support for the hardware monitoring + functionality of the Nuvoton NCT6775F, NCT6776F, and NCT6779D + Super-I/O chips. This driver replaces the w83627ehf driver for + NCT6775F and NCT6776F. + + This driver can also be built as a module. If so, the module + will be called nct6775. + config SENSORS_NTC_THERMISTOR tristate "NTC thermistor support" depends on (!OF && !IIO) || (OF && IIO) diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 5d36a57c055..82975724d3a 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -105,6 +105,7 @@ obj-$(CONFIG_SENSORS_MAX6650) += max6650.o obj-$(CONFIG_SENSORS_MAX6697) += max6697.o obj-$(CONFIG_SENSORS_MC13783_ADC)+= mc13783-adc.o obj-$(CONFIG_SENSORS_MCP3021) += mcp3021.o +obj-$(CONFIG_SENSORS_NCT6775) += nct6775.o obj-$(CONFIG_SENSORS_NTC_THERMISTOR) += ntc_thermistor.o obj-$(CONFIG_SENSORS_PC87360) += pc87360.o obj-$(CONFIG_SENSORS_PC87427) += pc87427.o diff --git a/drivers/hwmon/nct6775.c b/drivers/hwmon/nct6775.c new file mode 100644 index 00000000000..f75cd823153 --- /dev/null +++ b/drivers/hwmon/nct6775.c @@ -0,0 +1,1021 @@ +/* + * nct6775 - Driver for the hardware monitoring functionality of + * Nuvoton NCT677x Super-I/O chips + * + * Copyright (C) 2012 Guenter Roeck <linux@roeck-us.net> + * + * Derived from w83627ehf driver + * Copyright (C) 2005-2012 Jean Delvare <khali@linux-fr.org> + * Copyright (C) 2006 Yuan Mu (Winbond), + * Rudolf Marek <r.marek@assembler.cz> + * David Hubbard <david.c.hubbard@gmail.com> + * Daniel J Blueman <daniel.blueman@gmail.com> + * Copyright (C) 2010 Sheng-Yuan Huang (Nuvoton) (PS00) + * + * Shamelessly ripped from the w83627hf driver + * Copyright (C) 2003 Mark Studebaker + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + * + * Supports the following chips: + * + * Chip #vin #fan #pwm #temp chip IDs man ID + * nct6775f 9 4 3 6+3 0xb470 0xc1 0x5ca3 + * nct6776f 9 5 3 6+3 0xc330 0xc1 0x5ca3 + * nct6779d 15 5 5 2+6 0xc560 0xc1 0x5ca3 + * + * #temp lists the number of monitored temperature sources (first value) plus + * the number of directly connectable temperature sensors (second value). + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/jiffies.h> +#include <linux/platform_device.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/hwmon-vid.h> +#include <linux/err.h> +#include <linux/mutex.h> +#include <linux/acpi.h> +#include <linux/io.h> +#include "lm75.h" + +enum kinds { nct6775, nct6776, nct6779 }; + +/* used to set data->name = nct6775_device_names[data->sio_kind] */ +static const char * const nct6775_device_names[] = { + "nct6775", + "nct6776", + "nct6779", +}; + +static unsigned short force_id; +module_param(force_id, ushort, 0); +MODULE_PARM_DESC(force_id, "Override the detected device ID"); + +#define DRVNAME "nct6775" + +/* + * Super-I/O constants and functions + */ + +#define NCT6775_LD_HWM 0x0b +#define NCT6775_LD_VID 0x0d + +#define SIO_REG_LDSEL 0x07 /* Logical device select */ +#define SIO_REG_DEVID 0x20 /* Device ID (2 bytes) */ +#define SIO_REG_ENABLE 0x30 /* Logical device enable */ +#define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */ + +#define SIO_NCT6775_ID 0xb470 +#define SIO_NCT6776_ID 0xc330 +#define SIO_NCT6779_ID 0xc560 +#define SIO_ID_MASK 0xFFF0 + +static inline void +superio_outb(int ioreg, int reg, int val) +{ + outb(reg, ioreg); + outb(val, ioreg + 1); +} + +static inline int +superio_inb(int ioreg, int reg) +{ + outb(reg, ioreg); + return inb(ioreg + 1); +} + +static inline void +superio_select(int ioreg, int ld) +{ + outb(SIO_REG_LDSEL, ioreg); + outb(ld, ioreg + 1); +} + +static inline int +superio_enter(int ioreg) +{ + /* + * Try to reserve <ioreg> and <ioreg + 1> for exclusive access. + */ + if (!request_muxed_region(ioreg, 2, DRVNAME)) + return -EBUSY; + + outb(0x87, ioreg); + outb(0x87, ioreg); + + return 0; +} + +static inline void +superio_exit(int ioreg) +{ + outb(0xaa, ioreg); + outb(0x02, ioreg); + outb(0x02, ioreg + 1); + release_region(ioreg, 2); +} + +/* + * ISA constants + */ + +#define IOREGION_ALIGNMENT (~7) +#define IOREGION_OFFSET 5 +#define IOREGION_LENGTH 2 +#define ADDR_REG_OFFSET 0 +#define DATA_REG_OFFSET 1 + +#define NCT6775_REG_BANK 0x4E +#define NCT6775_REG_CONFIG 0x40 + +/* + * Not currently used: + * REG_MAN_ID has the value 0x5ca3 for all supported chips. + * REG_CHIP_ID == 0x88/0xa1/0xc1 depending on chip model. + * REG_MAN_ID is at port 0x4f + * REG_CHIP_ID is at port 0x58 + */ + +#define NUM_REG_ALARM 4 /* Max number of alarm registers */ + +/* Common and NCT6775 specific data */ + +/* Voltage min/max registers for nr=7..14 are in bank 5 */ + +static const u16 NCT6775_REG_IN_MAX[] = { + 0x2b, 0x2d, 0x2f, 0x31, 0x33, 0x35, 0x37, 0x554, 0x556, 0x558, 0x55a, + 0x55c, 0x55e, 0x560, 0x562 }; +static const u16 NCT6775_REG_IN_MIN[] = { + 0x2c, 0x2e, 0x30, 0x32, 0x34, 0x36, 0x38, 0x555, 0x557, 0x559, 0x55b, + 0x55d, 0x55f, 0x561, 0x563 }; +static const u16 NCT6775_REG_IN[] = { + 0x20, 0x21, 0x22, 0x23, 0x24, 0x25, 0x26, 0x550, 0x551, 0x552 +}; + +#define NCT6775_REG_VBAT 0x5D + +static const u16 NCT6775_REG_ALARM[NUM_REG_ALARM] = { 0x459, 0x45A, 0x45B }; + +/* 0..15 voltages, 16..23 fans, 24..31 temperatures */ + +static const s8 NCT6775_ALARM_BITS[] = { + 0, 1, 2, 3, 8, 21, 20, 16, /* in0.. in7 */ + 17, -1, -1, -1, -1, -1, -1, /* in8..in14 */ + -1, /* unused */ + 6, 7, 11, 10, 23, /* fan1..fan5 */ + -1, -1, -1, /* unused */ + 4, 5, 13, -1, -1, -1, /* temp1..temp6 */ + 12, -1 }; /* intrusion0, intrusion1 */ + +/* NCT6776 specific data */ + +static const s8 NCT6776_ALARM_BITS[] = { + 0, 1, 2, 3, 8, 21, 20, 16, /* in0.. in7 */ + 17, -1, -1, -1, -1, -1, -1, /* in8..in14 */ + -1, /* unused */ + 6, 7, 11, 10, 23, /* fan1..fan5 */ + -1, -1, -1, /* unused */ + 4, 5, 13, -1, -1, -1, /* temp1..temp6 */ + 12, 9 }; /* intrusion0, intrusion1 */ + +/* NCT6779 specific data */ + +static const u16 NCT6779_REG_IN[] = { + 0x480, 0x481, 0x482, 0x483, 0x484, 0x485, 0x486, 0x487, + 0x488, 0x489, 0x48a, 0x48b, 0x48c, 0x48d, 0x48e }; + +static const u16 NCT6779_REG_ALARM[NUM_REG_ALARM] = { + 0x459, 0x45A, 0x45B, 0x568 }; + +static const s8 NCT6779_ALARM_BITS[] = { + 0, 1, 2, 3, 8, 21, 20, 16, /* in0.. in7 */ + 17, 24, 25, 26, 27, 28, 29, /* in8..in14 */ + -1, /* unused */ + 6, 7, 11, 10, 23, /* fan1..fan5 */ + -1, -1, -1, /* unused */ + 4, 5, 13, -1, -1, -1, /* temp1..temp6 */ + 12, 9 }; /* intrusion0, intrusion1 */ + +/* + * Conversions + */ + +/* + * Some of the voltage inputs have internal scaling, the tables below + * contain 8 (the ADC LSB in mV) * scaling factor * 100 + */ +static const u16 scale_in[15] = { + 800, 800, 1600, 1600, 800, 800, 800, 1600, 1600, 800, 800, 800, 800, + 800, 800 +}; + +static inline long in_from_reg(u8 reg, u8 nr) +{ + return DIV_ROUND_CLOSEST(reg * scale_in[nr], 100); +} + +static inline u8 in_to_reg(u32 val, u8 nr) +{ + return clamp_val(DIV_ROUND_CLOSEST(val * 100, scale_in[nr]), 0, 255); +} + +/* + * Data structures and manipulation thereof + */ + +struct nct6775_data { + int addr; /* IO base of hw monitor block */ + enum kinds kind; + const char *name; + + struct device *hwmon_dev; + struct mutex lock; + + u16 REG_CONFIG; + u16 REG_VBAT; + + const s8 *ALARM_BITS; + + const u16 *REG_VIN; + const u16 *REG_IN_MINMAX[2]; + + const u16 *REG_ALARM; + + struct mutex update_lock; + bool valid; /* true if following fields are valid */ + unsigned long last_updated; /* In jiffies */ + + /* Register values */ + u8 bank; /* current register bank */ + u8 in_num; /* number of in inputs we have */ + u8 in[15][3]; /* [0]=in, [1]=in_max, [2]=in_min */ + + u64 alarms; + + u8 vid; + u8 vrm; + + u16 have_in; +}; + +struct nct6775_sio_data { + int sioreg; + enum kinds kind; +}; + +static bool is_word_sized(struct nct6775_data *data, u16 reg) +{ + switch (data->kind) { + case nct6775: + return (((reg & 0xff00) == 0x100 || + (reg & 0xff00) == 0x200) && + ((reg & 0x00ff) == 0x50 || + (reg & 0x00ff) == 0x53 || + (reg & 0x00ff) == 0x55)) || + (reg & 0xfff0) == 0x630 || + reg == 0x640 || reg == 0x642 || + reg == 0x662 || + ((reg & 0xfff0) == 0x650 && (reg & 0x000f) >= 0x06) || + reg == 0x73 || reg == 0x75 || reg == 0x77; + case nct6776: + return (((reg & 0xff00) == 0x100 || + (reg & 0xff00) == 0x200) && + ((reg & 0x00ff) == 0x50 || + (reg & 0x00ff) == 0x53 || + (reg & 0x00ff) == 0x55)) || + (reg & 0xfff0) == 0x630 || + reg == 0x402 || + reg == 0x640 || reg == 0x642 || + ((reg & 0xfff0) == 0x650 && (reg & 0x000f) >= 0x06) || + reg == 0x73 || reg == 0x75 || reg == 0x77; + case nct6779: + return reg == 0x150 || reg == 0x153 || reg == 0x155 || + ((reg & 0xfff0) == 0x4b0 && (reg & 0x000f) < 0x09) || + reg == 0x402 || + reg == 0x63a || reg == 0x63c || reg == 0x63e || + reg == 0x640 || reg == 0x642 || + reg == 0x73 || reg == 0x75 || reg == 0x77 || reg == 0x79 || + reg == 0x7b; + } + return false; +} + +/* + * On older chips, only registers 0x50-0x5f are banked. + * On more recent chips, all registers are banked. + * Assume that is the case and set the bank number for each access. + * Cache the bank number so it only needs to be set if it changes. + */ +static inline void nct6775_set_bank(struct nct6775_data *data, u16 reg) +{ + u8 bank = reg >> 8; + if (data->bank != bank) { + outb_p(NCT6775_REG_BANK, data->addr + ADDR_REG_OFFSET); + outb_p(bank, data->addr + DATA_REG_OFFSET); + data->bank = bank; + } +} + +static u16 nct6775_read_value(struct nct6775_data *data, u16 reg) +{ + int res, word_sized = is_word_sized(data, reg); + + mutex_lock(&data->lock); + + nct6775_set_bank(data, reg); + outb_p(reg & 0xff, data->addr + ADDR_REG_OFFSET); + res = inb_p(data->addr + DATA_REG_OFFSET); + if (word_sized) { + outb_p((reg & 0xff) + 1, + data->addr + ADDR_REG_OFFSET); + res = (res << 8) + inb_p(data->addr + DATA_REG_OFFSET); + } + + mutex_unlock(&data->lock); + return res; +} + +static int nct6775_write_value(struct nct6775_data *data, u16 reg, u16 value) +{ + int word_sized = is_word_sized(data, reg); + + mutex_lock(&data->lock); + + nct6775_set_bank(data, reg); + outb_p(reg & 0xff, data->addr + ADDR_REG_OFFSET); + if (word_sized) { + outb_p(value >> 8, data->addr + DATA_REG_OFFSET); + outb_p((reg & 0xff) + 1, + data->addr + ADDR_REG_OFFSET); + } + outb_p(value & 0xff, data->addr + DATA_REG_OFFSET); + + mutex_unlock(&data->lock); + return 0; +} + +static struct nct6775_data *nct6775_update_device(struct device *dev) +{ + struct nct6775_data *data = dev_get_drvdata(dev); + int i; + + mutex_lock(&data->update_lock); + + if (time_after(jiffies, data->last_updated + HZ + HZ/2) + || !data->valid) { + /* Measured voltages and limits */ + for (i = 0; i < data->in_num; i++) { + if (!(data->have_in & (1 << i))) + continue; + + data->in[i][0] = nct6775_read_value(data, + data->REG_VIN[i]); + data->in[i][1] = nct6775_read_value(data, + data->REG_IN_MINMAX[0][i]); + data->in[i][2] = nct6775_read_value(data, + data->REG_IN_MINMAX[1][i]); + } + + data->alarms = 0; + for (i = 0; i < NUM_REG_ALARM; i++) { + u8 alarm; + if (!data->REG_ALARM[i]) + continue; + alarm = nct6775_read_value(data, data->REG_ALARM[i]); + data->alarms |= ((u64)alarm) << (i << 3); + } + + data->last_updated = jiffies; + data->valid = true; + } + + mutex_unlock(&data->update_lock); + return data; +} + +/* + * Sysfs callback functions + */ +static ssize_t +show_in_reg(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct nct6775_data *data = nct6775_update_device(dev); + struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr); + int nr = sattr->nr; + int index = sattr->index; + return sprintf(buf, "%ld\n", in_from_reg(data->in[nr][index], nr)); +} + +static ssize_t +store_in_reg(struct device *dev, struct device_attribute *attr, const char *buf, + size_t count) +{ + struct nct6775_data *data = dev_get_drvdata(dev); + struct sensor_device_attribute_2 *sattr = to_sensor_dev_attr_2(attr); + int nr = sattr->nr; + int index = sattr->index; + unsigned long val; + int err = kstrtoul(buf, 10, &val); + if (err < 0) + return err; + mutex_lock(&data->update_lock); + data->in[nr][index] = in_to_reg(val, nr); + nct6775_write_value(data, data->REG_IN_MINMAX[index-1][nr], + data->in[nr][index]); + mutex_unlock(&data->update_lock); + return count; +} + +static ssize_t +show_alarm(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct nct6775_data *data = nct6775_update_device(dev); + struct sensor_device_attribute *sattr = to_sensor_dev_attr(attr); + int nr = data->ALARM_BITS[sattr->index]; + return sprintf(buf, "%u\n", + (unsigned int)((data->alarms >> nr) & 0x01)); +} + +static SENSOR_DEVICE_ATTR_2(in0_input, S_IRUGO, show_in_reg, NULL, 0, 0); +static SENSOR_DEVICE_ATTR_2(in1_input, S_IRUGO, show_in_reg, NULL, 1, 0); +static SENSOR_DEVICE_ATTR_2(in2_input, S_IRUGO, show_in_reg, NULL, 2, 0); +static SENSOR_DEVICE_ATTR_2(in3_input, S_IRUGO, show_in_reg, NULL, 3, 0); +static SENSOR_DEVICE_ATTR_2(in4_input, S_IRUGO, show_in_reg, NULL, 4, 0); +static SENSOR_DEVICE_ATTR_2(in5_input, S_IRUGO, show_in_reg, NULL, 5, 0); +static SENSOR_DEVICE_ATTR_2(in6_input, S_IRUGO, show_in_reg, NULL, 6, 0); +static SENSOR_DEVICE_ATTR_2(in7_input, S_IRUGO, show_in_reg, NULL, 7, 0); +static SENSOR_DEVICE_ATTR_2(in8_input, S_IRUGO, show_in_reg, NULL, 8, 0); +static SENSOR_DEVICE_ATTR_2(in9_input, S_IRUGO, show_in_reg, NULL, 9, 0); +static SENSOR_DEVICE_ATTR_2(in10_input, S_IRUGO, show_in_reg, NULL, 10, 0); +static SENSOR_DEVICE_ATTR_2(in11_input, S_IRUGO, show_in_reg, NULL, 11, 0); +static SENSOR_DEVICE_ATTR_2(in12_input, S_IRUGO, show_in_reg, NULL, 12, 0); +static SENSOR_DEVICE_ATTR_2(in13_input, S_IRUGO, show_in_reg, NULL, 13, 0); +static SENSOR_DEVICE_ATTR_2(in14_input, S_IRUGO, show_in_reg, NULL, 14, 0); + +static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0); +static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1); +static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 2); +static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 3); +static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 4); +static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, 5); +static SENSOR_DEVICE_ATTR(in6_alarm, S_IRUGO, show_alarm, NULL, 6); +static SENSOR_DEVICE_ATTR(in7_alarm, S_IRUGO, show_alarm, NULL, 7); +static SENSOR_DEVICE_ATTR(in8_alarm, S_IRUGO, show_alarm, NULL, 8); +static SENSOR_DEVICE_ATTR(in9_alarm, S_IRUGO, show_alarm, NULL, 9); +static SENSOR_DEVICE_ATTR(in10_alarm, S_IRUGO, show_alarm, NULL, 10); +static SENSOR_DEVICE_ATTR(in11_alarm, S_IRUGO, show_alarm, NULL, 11); +static SENSOR_DEVICE_ATTR(in12_alarm, S_IRUGO, show_alarm, NULL, 12); +static SENSOR_DEVICE_ATTR(in13_alarm, S_IRUGO, show_alarm, NULL, 13); +static SENSOR_DEVICE_ATTR(in14_alarm, S_IRUGO, show_alarm, NULL, 14); + +static SENSOR_DEVICE_ATTR_2(in0_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 0, 1); +static SENSOR_DEVICE_ATTR_2(in1_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 1, 1); +static SENSOR_DEVICE_ATTR_2(in2_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 2, 1); +static SENSOR_DEVICE_ATTR_2(in3_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 3, 1); +static SENSOR_DEVICE_ATTR_2(in4_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 4, 1); +static SENSOR_DEVICE_ATTR_2(in5_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 5, 1); +static SENSOR_DEVICE_ATTR_2(in6_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 6, 1); +static SENSOR_DEVICE_ATTR_2(in7_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 7, 1); +static SENSOR_DEVICE_ATTR_2(in8_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 8, 1); +static SENSOR_DEVICE_ATTR_2(in9_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 9, 1); +static SENSOR_DEVICE_ATTR_2(in10_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 10, 1); +static SENSOR_DEVICE_ATTR_2(in11_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 11, 1); +static SENSOR_DEVICE_ATTR_2(in12_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 12, 1); +static SENSOR_DEVICE_ATTR_2(in13_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 13, 1); +static SENSOR_DEVICE_ATTR_2(in14_min, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 14, 1); + +static SENSOR_DEVICE_ATTR_2(in0_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 0, 2); +static SENSOR_DEVICE_ATTR_2(in1_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 1, 2); +static SENSOR_DEVICE_ATTR_2(in2_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 2, 2); +static SENSOR_DEVICE_ATTR_2(in3_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 3, 2); +static SENSOR_DEVICE_ATTR_2(in4_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 4, 2); +static SENSOR_DEVICE_ATTR_2(in5_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 5, 2); +static SENSOR_DEVICE_ATTR_2(in6_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 6, 2); +static SENSOR_DEVICE_ATTR_2(in7_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 7, 2); +static SENSOR_DEVICE_ATTR_2(in8_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 8, 2); +static SENSOR_DEVICE_ATTR_2(in9_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 9, 2); +static SENSOR_DEVICE_ATTR_2(in10_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 10, 2); +static SENSOR_DEVICE_ATTR_2(in11_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 11, 2); +static SENSOR_DEVICE_ATTR_2(in12_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 12, 2); +static SENSOR_DEVICE_ATTR_2(in13_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 13, 2); +static SENSOR_DEVICE_ATTR_2(in14_max, S_IWUSR | S_IRUGO, show_in_reg, + store_in_reg, 14, 2); + +static struct attribute *nct6775_attributes_in[15][5] = { + { + &sensor_dev_attr_in0_input.dev_attr.attr, + &sensor_dev_attr_in0_min.dev_attr.attr, + &sensor_dev_attr_in0_max.dev_attr.attr, + &sensor_dev_attr_in0_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in1_input.dev_attr.attr, + &sensor_dev_attr_in1_min.dev_attr.attr, + &sensor_dev_attr_in1_max.dev_attr.attr, + &sensor_dev_attr_in1_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in2_input.dev_attr.attr, + &sensor_dev_attr_in2_min.dev_attr.attr, + &sensor_dev_attr_in2_max.dev_attr.attr, + &sensor_dev_attr_in2_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in3_input.dev_attr.attr, + &sensor_dev_attr_in3_min.dev_attr.attr, + &sensor_dev_attr_in3_max.dev_attr.attr, + &sensor_dev_attr_in3_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in4_input.dev_attr.attr, + &sensor_dev_attr_in4_min.dev_attr.attr, + &sensor_dev_attr_in4_max.dev_attr.attr, + &sensor_dev_attr_in4_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in5_input.dev_attr.attr, + &sensor_dev_attr_in5_min.dev_attr.attr, + &sensor_dev_attr_in5_max.dev_attr.attr, + &sensor_dev_attr_in5_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in6_input.dev_attr.attr, + &sensor_dev_attr_in6_min.dev_attr.attr, + &sensor_dev_attr_in6_max.dev_attr.attr, + &sensor_dev_attr_in6_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in7_input.dev_attr.attr, + &sensor_dev_attr_in7_min.dev_attr.attr, + &sensor_dev_attr_in7_max.dev_attr.attr, + &sensor_dev_attr_in7_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in8_input.dev_attr.attr, + &sensor_dev_attr_in8_min.dev_attr.attr, + &sensor_dev_attr_in8_max.dev_attr.attr, + &sensor_dev_attr_in8_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in9_input.dev_attr.attr, + &sensor_dev_attr_in9_min.dev_attr.attr, + &sensor_dev_attr_in9_max.dev_attr.attr, + &sensor_dev_attr_in9_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in10_input.dev_attr.attr, + &sensor_dev_attr_in10_min.dev_attr.attr, + &sensor_dev_attr_in10_max.dev_attr.attr, + &sensor_dev_attr_in10_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in11_input.dev_attr.attr, + &sensor_dev_attr_in11_min.dev_attr.attr, + &sensor_dev_attr_in11_max.dev_attr.attr, + &sensor_dev_attr_in11_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in12_input.dev_attr.attr, + &sensor_dev_attr_in12_min.dev_attr.attr, + &sensor_dev_attr_in12_max.dev_attr.attr, + &sensor_dev_attr_in12_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in13_input.dev_attr.attr, + &sensor_dev_attr_in13_min.dev_attr.attr, + &sensor_dev_attr_in13_max.dev_attr.attr, + &sensor_dev_attr_in13_alarm.dev_attr.attr, + NULL + }, + { + &sensor_dev_attr_in14_input.dev_attr.attr, + &sensor_dev_attr_in14_min.dev_attr.attr, + &sensor_dev_attr_in14_max.dev_attr.attr, + &sensor_dev_attr_in14_alarm.dev_attr.attr, + NULL + }, +}; + +static const struct attribute_group nct6775_group_in[15] = { + { .attrs = nct6775_attributes_in[0] }, + { .attrs = nct6775_attributes_in[1] }, + { .attrs = nct6775_attributes_in[2] }, + { .attrs = nct6775_attributes_in[3] }, + { .attrs = nct6775_attributes_in[4] }, + { .attrs = nct6775_attributes_in[5] }, + { .attrs = nct6775_attributes_in[6] }, + { .attrs = nct6775_attributes_in[7] }, + { .attrs = nct6775_attributes_in[8] }, + { .attrs = nct6775_attributes_in[9] }, + { .attrs = nct6775_attributes_in[10] }, + { .attrs = nct6775_attributes_in[11] }, + { .attrs = nct6775_attributes_in[12] }, + { .attrs = nct6775_attributes_in[13] }, + { .attrs = nct6775_attributes_in[14] }, +}; + +static ssize_t +show_name(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct nct6775_data *data = dev_get_drvdata(dev); + + return sprintf(buf, "%s\n", data->name); +} + +static DEVICE_ATTR(name, S_IRUGO, show_name, NULL); + +static ssize_t +show_vid(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct nct6775_data *data = dev_get_drvdata(dev); + return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm)); +} + +static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL); + +/* + * Driver and device management + */ + +static void nct6775_device_remove_files(struct device *dev) +{ + /* + * some entries in the following arrays may not have been used in + * device_create_file(), but device_remove_file() will ignore them + */ + int i; + struct nct6775_data *data = dev_get_drvdata(dev); + + for (i = 0; i < data->in_num; i++) + sysfs_remove_group(&dev->kobj, &nct6775_group_in[i]); + + device_remove_file(dev, &dev_attr_name); + device_remove_file(dev, &dev_attr_cpu0_vid); +} + +/* Get the monitoring functions started */ +static inline void nct6775_init_device(struct nct6775_data *data) +{ + u8 tmp; + + /* Start monitoring if needed */ + if (data->REG_CONFIG) { + tmp = nct6775_read_value(data, data->REG_CONFIG); + if (!(tmp & 0x01)) + nct6775_write_value(data, data->REG_CONFIG, tmp | 0x01); + } + + /* Enable VBAT monitoring if needed */ + tmp = nct6775_read_value(data, data->REG_VBAT); + if (!(tmp & 0x01)) + nct6775_write_value(data, data->REG_VBAT, tmp | 0x01); +} + +static int nct6775_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct nct6775_sio_data *sio_data = dev->platform_data; + struct nct6775_data *data; + struct resource *res; + int i, err = 0; + + res = platform_get_resource(pdev, IORESOURCE_IO, 0); + if (!devm_request_region(&pdev->dev, res->start, IOREGION_LENGTH, + DRVNAME)) + return -EBUSY; + + data = devm_kzalloc(&pdev->dev, sizeof(struct nct6775_data), + GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->kind = sio_data->kind; + data->addr = res->start; + mutex_init(&data->lock); + mutex_init(&data->update_lock); + data->name = nct6775_device_names[data->kind]; + data->bank = 0xff; /* Force initial bank selection */ + platform_set_drvdata(pdev, data); + + switch (data->kind) { + case nct6775: + data->in_num = 9; + + data->ALARM_BITS = NCT6775_ALARM_BITS; + + data->REG_CONFIG = NCT6775_REG_CONFIG; + data->REG_VBAT = NCT6775_REG_VBAT; + data->REG_VIN = NCT6775_REG_IN; + data->REG_IN_MINMAX[0] = NCT6775_REG_IN_MIN; + data->REG_IN_MINMAX[1] = NCT6775_REG_IN_MAX; + data->REG_ALARM = NCT6775_REG_ALARM; + break; + case nct6776: + data->in_num = 9; + + data->ALARM_BITS = NCT6776_ALARM_BITS; + + data->REG_CONFIG = NCT6775_REG_CONFIG; + data->REG_VBAT = NCT6775_REG_VBAT; + data->REG_VIN = NCT6775_REG_IN; + data->REG_IN_MINMAX[0] = NCT6775_REG_IN_MIN; + data->REG_IN_MINMAX[1] = NCT6775_REG_IN_MAX; + data->REG_ALARM = NCT6775_REG_ALARM; + break; + case nct6779: + data->in_num = 15; + + data->ALARM_BITS = NCT6779_ALARM_BITS; + + data->REG_CONFIG = NCT6775_REG_CONFIG; + data->REG_VBAT = NCT6775_REG_VBAT; + data->REG_VIN = NCT6779_REG_IN; + data->REG_IN_MINMAX[0] = NCT6775_REG_IN_MIN; + data->REG_IN_MINMAX[1] = NCT6775_REG_IN_MAX; + data->REG_ALARM = NCT6779_REG_ALARM; + break; + default: + return -ENODEV; + } + data->have_in = (1 << data->in_num) - 1; + + /* Initialize the chip */ + nct6775_init_device(data); + + data->vrm = vid_which_vrm(); + err = superio_enter(sio_data->sioreg); + if (err) + return err; + + /* + * Read VID value + * We can get the VID input values directly at logical device D 0xe3. + */ + superio_select(sio_data->sioreg, NCT6775_LD_VID); + data->vid = superio_inb(sio_data->sioreg, 0xe3); + superio_exit(sio_data->sioreg); + + err = device_create_file(dev, &dev_attr_cpu0_vid); + if (err) + return err; + + for (i = 0; i < data->in_num; i++) { + if (!(data->have_in & (1 << i))) + continue; + err = sysfs_create_group(&dev->kobj, &nct6775_group_in[i]); + if (err) + goto exit_remove; + } + + err = device_create_file(dev, &dev_attr_name); + if (err) + goto exit_remove; + + data->hwmon_dev = hwmon_device_register(dev); + if (IS_ERR(data->hwmon_dev)) { + err = PTR_ERR(data->hwmon_dev); + goto exit_remove; + } + + return 0; + +exit_remove: + nct6775_device_remove_files(dev); + return err; +} + +static int nct6775_remove(struct platform_device *pdev) +{ + struct nct6775_data *data = platform_get_drvdata(pdev); + + hwmon_device_unregister(data->hwmon_dev); + nct6775_device_remove_files(&pdev->dev); + + return 0; +} + +static struct platform_driver nct6775_driver = { + .driver = { + .owner = THIS_MODULE, + .name = DRVNAME, + }, + .probe = nct6775_probe, + .remove = nct6775_remove, +}; + +/* nct6775_find() looks for a '627 in the Super-I/O config space */ +static int __init nct6775_find(int sioaddr, unsigned short *addr, + struct nct6775_sio_data *sio_data) +{ + static const char sio_name_NCT6775[] __initconst = "NCT6775F"; + static const char sio_name_NCT6776[] __initconst = "NCT6776F"; + static const char sio_name_NCT6779[] __initconst = "NCT6779D"; + + u16 val; + const char *sio_name; + int err; + + err = superio_enter(sioaddr); + if (err) + return err; + + if (force_id) + val = force_id; + else + val = (superio_inb(sioaddr, SIO_REG_DEVID) << 8) + | superio_inb(sioaddr, SIO_REG_DEVID + 1); + switch (val & SIO_ID_MASK) { + case SIO_NCT6775_ID: + sio_data->kind = nct6775; + sio_name = sio_name_NCT6775; + break; + case SIO_NCT6776_ID: + sio_data->kind = nct6776; + sio_name = sio_name_NCT6776; + break; + case SIO_NCT6779_ID: + sio_data->kind = nct6779; + sio_name = sio_name_NCT6779; + break; + default: + if (val != 0xffff) + pr_debug("unsupported chip ID: 0x%04x\n", val); + superio_exit(sioaddr); + return -ENODEV; + } + + /* We have a known chip, find the HWM I/O address */ + superio_select(sioaddr, NCT6775_LD_HWM); + val = (superio_inb(sioaddr, SIO_REG_ADDR) << 8) + | superio_inb(sioaddr, SIO_REG_ADDR + 1); + *addr = val & IOREGION_ALIGNMENT; + if (*addr == 0) { + pr_err("Refusing to enable a Super-I/O device with a base I/O port 0\n"); + superio_exit(sioaddr); + return -ENODEV; + } + + /* Activate logical device if needed */ + val = superio_inb(sioaddr, SIO_REG_ENABLE); + if (!(val & 0x01)) { + pr_warn("Forcibly enabling Super-I/O. Sensor is probably unusable.\n"); + superio_outb(sioaddr, SIO_REG_ENABLE, val | 0x01); + } + + superio_exit(sioaddr); + pr_info("Found %s chip at %#x\n", sio_name, *addr); + sio_data->sioreg = sioaddr; + + return 0; +} + +/* + * when Super-I/O functions move to a separate file, the Super-I/O + * bus will manage the lifetime of the device and this module will only keep + * track of the nct6775 driver. But since we platform_device_alloc(), we + * must keep track of the device + */ +static struct platform_device *pdev; + +static int __init sensors_nct6775_init(void) +{ + int err; + unsigned short address; + struct resource res; + struct nct6775_sio_data sio_data; + + /* + * initialize sio_data->kind and sio_data->sioreg. + * + * when Super-I/O functions move to a separate file, the Super-I/O + * driver will probe 0x2e and 0x4e and auto-detect the presence of a + * nct6775 hardware monitor, and call probe() + */ + if (nct6775_find(0x2e, &address, &sio_data) && + nct6775_find(0x4e, &address, &sio_data)) + return -ENODEV; + + err = platform_driver_register(&nct6775_driver); + if (err) + goto exit; + + pdev = platform_device_alloc(DRVNAME, address); + if (!pdev) { + err = -ENOMEM; + pr_err("Device allocation failed\n"); + goto exit_unregister; + } + + err = platform_device_add_data(pdev, &sio_data, + sizeof(struct nct6775_sio_data)); + if (err) { + pr_err("Platform data allocation failed\n"); + goto exit_device_put; + } + + memset(&res, 0, sizeof(res)); + res.name = DRVNAME; + res.start = address + IOREGION_OFFSET; + res.end = address + IOREGION_OFFSET + IOREGION_LENGTH - 1; + res.flags = IORESOURCE_IO; + + err = acpi_check_resource_conflict(&res); + if (err) + goto exit_device_put; + + err = platform_device_add_resources(pdev, &res, 1); + if (err) { + pr_err("Device resource addition failed (%d)\n", err); + goto exit_device_put; + } + + /* platform_device_add calls probe() */ + err = platform_device_add(pdev); + if (err) { + pr_err("Device addition failed (%d)\n", err); + goto exit_device_put; + } + + return 0; + +exit_device_put: + platform_device_put(pdev); +exit_unregister: + platform_driver_unregister(&nct6775_driver); +exit: + return err; +} + +static void __exit sensors_nct6775_exit(void) +{ + platform_device_unregister(pdev); + platform_driver_unregister(&nct6775_driver); +} + +MODULE_AUTHOR("Guenter Roeck <linux@roeck-us.net>"); +MODULE_DESCRIPTION("NCT6775F/NCT6776F/NCT6779D driver"); +MODULE_LICENSE("GPL"); + +module_init(sensors_nct6775_init); +module_exit(sensors_nct6775_exit); |