[PATCH] PCI: clean up pci.h and split pci register info to separate header file.

This cleans up some of the #ifdef CONFIG_PCI stuff up, and moves the pci register
info out to a separate file, where it belongs.  Eventually we can stop including
this file from within pci.h, but lots of code needs to be audited first.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

2 files changed, 477 insertions, 458 deletions

diff --git a/include/linux/pci.h b/include/linux/pci.h
index e7a228f2fdd..830c1bae56c 100644
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -19,436 +19,10 @@
 
 #include <linux/mod_devicetable.h>
 
-/*
- * Under PCI, each device has 256 bytes of configuration address space,
- * of which the first 64 bytes are standardized as follows:
- */
-#define PCI_VENDOR_ID		0x00	/* 16 bits */
-#define PCI_DEVICE_ID		0x02	/* 16 bits */
-#define PCI_COMMAND		0x04	/* 16 bits */
-#define  PCI_COMMAND_IO		0x1	/* Enable response in I/O space */
-#define  PCI_COMMAND_MEMORY	0x2	/* Enable response in Memory space */
-#define  PCI_COMMAND_MASTER	0x4	/* Enable bus mastering */
-#define  PCI_COMMAND_SPECIAL	0x8	/* Enable response to special cycles */
-#define  PCI_COMMAND_INVALIDATE	0x10	/* Use memory write and invalidate */
-#define  PCI_COMMAND_VGA_PALETTE 0x20	/* Enable palette snooping */
-#define  PCI_COMMAND_PARITY	0x40	/* Enable parity checking */
-#define  PCI_COMMAND_WAIT 	0x80	/* Enable address/data stepping */
-#define  PCI_COMMAND_SERR	0x100	/* Enable SERR */
-#define  PCI_COMMAND_FAST_BACK	0x200	/* Enable back-to-back writes */
-#define  PCI_COMMAND_INTX_DISABLE 0x400 /* INTx Emulation Disable */
-
-#define PCI_STATUS		0x06	/* 16 bits */
-#define  PCI_STATUS_CAP_LIST	0x10	/* Support Capability List */
-#define  PCI_STATUS_66MHZ	0x20	/* Support 66 Mhz PCI 2.1 bus */
-#define  PCI_STATUS_UDF		0x40	/* Support User Definable Features [obsolete] */
-#define  PCI_STATUS_FAST_BACK	0x80	/* Accept fast-back to back */
-#define  PCI_STATUS_PARITY	0x100	/* Detected parity error */
-#define  PCI_STATUS_DEVSEL_MASK	0x600	/* DEVSEL timing */
-#define  PCI_STATUS_DEVSEL_FAST	0x000	
-#define  PCI_STATUS_DEVSEL_MEDIUM 0x200
-#define  PCI_STATUS_DEVSEL_SLOW 0x400
-#define  PCI_STATUS_SIG_TARGET_ABORT 0x800 /* Set on target abort */
-#define  PCI_STATUS_REC_TARGET_ABORT 0x1000 /* Master ack of " */
-#define  PCI_STATUS_REC_MASTER_ABORT 0x2000 /* Set on master abort */
-#define  PCI_STATUS_SIG_SYSTEM_ERROR 0x4000 /* Set when we drive SERR */
-#define  PCI_STATUS_DETECTED_PARITY 0x8000 /* Set on parity error */
-
-#define PCI_CLASS_REVISION	0x08	/* High 24 bits are class, low 8
-					   revision */
-#define PCI_REVISION_ID         0x08    /* Revision ID */
-#define PCI_CLASS_PROG          0x09    /* Reg. Level Programming Interface */
-#define PCI_CLASS_DEVICE        0x0a    /* Device class */
-
-#define PCI_CACHE_LINE_SIZE	0x0c	/* 8 bits */
-#define PCI_LATENCY_TIMER	0x0d	/* 8 bits */
-#define PCI_HEADER_TYPE		0x0e	/* 8 bits */
-#define  PCI_HEADER_TYPE_NORMAL	0
-#define  PCI_HEADER_TYPE_BRIDGE 1
-#define  PCI_HEADER_TYPE_CARDBUS 2
-
-#define PCI_BIST		0x0f	/* 8 bits */
-#define  PCI_BIST_CODE_MASK	0x0f	/* Return result */
-#define  PCI_BIST_START		0x40	/* 1 to start BIST, 2 secs or less */
-#define  PCI_BIST_CAPABLE	0x80	/* 1 if BIST capable */
-
-/*
- * Base addresses specify locations in memory or I/O space.
- * Decoded size can be determined by writing a value of 
- * 0xffffffff to the register, and reading it back.  Only 
- * 1 bits are decoded.
- */
-#define PCI_BASE_ADDRESS_0	0x10	/* 32 bits */
-#define PCI_BASE_ADDRESS_1	0x14	/* 32 bits [htype 0,1 only] */
-#define PCI_BASE_ADDRESS_2	0x18	/* 32 bits [htype 0 only] */
-#define PCI_BASE_ADDRESS_3	0x1c	/* 32 bits */
-#define PCI_BASE_ADDRESS_4	0x20	/* 32 bits */
-#define PCI_BASE_ADDRESS_5	0x24	/* 32 bits */
-#define  PCI_BASE_ADDRESS_SPACE	0x01	/* 0 = memory, 1 = I/O */
-#define  PCI_BASE_ADDRESS_SPACE_IO 0x01
-#define  PCI_BASE_ADDRESS_SPACE_MEMORY 0x00
-#define  PCI_BASE_ADDRESS_MEM_TYPE_MASK 0x06
-#define  PCI_BASE_ADDRESS_MEM_TYPE_32	0x00	/* 32 bit address */
-#define  PCI_BASE_ADDRESS_MEM_TYPE_1M	0x02	/* Below 1M [obsolete] */
-#define  PCI_BASE_ADDRESS_MEM_TYPE_64	0x04	/* 64 bit address */
-#define  PCI_BASE_ADDRESS_MEM_PREFETCH	0x08	/* prefetchable? */
-#define  PCI_BASE_ADDRESS_MEM_MASK	(~0x0fUL)
-#define  PCI_BASE_ADDRESS_IO_MASK	(~0x03UL)
-/* bit 1 is reserved if address_space = 1 */
-
-/* Header type 0 (normal devices) */
-#define PCI_CARDBUS_CIS		0x28
-#define PCI_SUBSYSTEM_VENDOR_ID	0x2c
-#define PCI_SUBSYSTEM_ID	0x2e  
-#define PCI_ROM_ADDRESS		0x30	/* Bits 31..11 are address, 10..1 reserved */
-#define  PCI_ROM_ADDRESS_ENABLE	0x01
-#define PCI_ROM_ADDRESS_MASK	(~0x7ffUL)
-
-#define PCI_CAPABILITY_LIST	0x34	/* Offset of first capability list entry */
-
-/* 0x35-0x3b are reserved */
-#define PCI_INTERRUPT_LINE	0x3c	/* 8 bits */
-#define PCI_INTERRUPT_PIN	0x3d	/* 8 bits */
-#define PCI_MIN_GNT		0x3e	/* 8 bits */
-#define PCI_MAX_LAT		0x3f	/* 8 bits */
-
-/* Header type 1 (PCI-to-PCI bridges) */
-#define PCI_PRIMARY_BUS		0x18	/* Primary bus number */
-#define PCI_SECONDARY_BUS	0x19	/* Secondary bus number */
-#define PCI_SUBORDINATE_BUS	0x1a	/* Highest bus number behind the bridge */
-#define PCI_SEC_LATENCY_TIMER	0x1b	/* Latency timer for secondary interface */
-#define PCI_IO_BASE		0x1c	/* I/O range behind the bridge */
-#define PCI_IO_LIMIT		0x1d
-#define  PCI_IO_RANGE_TYPE_MASK	0x0fUL	/* I/O bridging type */
-#define  PCI_IO_RANGE_TYPE_16	0x00
-#define  PCI_IO_RANGE_TYPE_32	0x01
-#define  PCI_IO_RANGE_MASK	(~0x0fUL)
-#define PCI_SEC_STATUS		0x1e	/* Secondary status register, only bit 14 used */
-#define PCI_MEMORY_BASE		0x20	/* Memory range behind */
-#define PCI_MEMORY_LIMIT	0x22
-#define  PCI_MEMORY_RANGE_TYPE_MASK 0x0fUL
-#define  PCI_MEMORY_RANGE_MASK	(~0x0fUL)
-#define PCI_PREF_MEMORY_BASE	0x24	/* Prefetchable memory range behind */
-#define PCI_PREF_MEMORY_LIMIT	0x26
-#define  PCI_PREF_RANGE_TYPE_MASK 0x0fUL
-#define  PCI_PREF_RANGE_TYPE_32	0x00
-#define  PCI_PREF_RANGE_TYPE_64	0x01
-#define  PCI_PREF_RANGE_MASK	(~0x0fUL)
-#define PCI_PREF_BASE_UPPER32	0x28	/* Upper half of prefetchable memory range */
-#define PCI_PREF_LIMIT_UPPER32	0x2c
-#define PCI_IO_BASE_UPPER16	0x30	/* Upper half of I/O addresses */
-#define PCI_IO_LIMIT_UPPER16	0x32
-/* 0x34 same as for htype 0 */
-/* 0x35-0x3b is reserved */
-#define PCI_ROM_ADDRESS1	0x38	/* Same as PCI_ROM_ADDRESS, but for htype 1 */
-/* 0x3c-0x3d are same as for htype 0 */
-#define PCI_BRIDGE_CONTROL	0x3e
-#define  PCI_BRIDGE_CTL_PARITY	0x01	/* Enable parity detection on secondary interface */
-#define  PCI_BRIDGE_CTL_SERR	0x02	/* The same for SERR forwarding */
-#define  PCI_BRIDGE_CTL_NO_ISA	0x04	/* Disable bridging of ISA ports */
-#define  PCI_BRIDGE_CTL_VGA	0x08	/* Forward VGA addresses */
-#define  PCI_BRIDGE_CTL_MASTER_ABORT 0x20  /* Report master aborts */
-#define  PCI_BRIDGE_CTL_BUS_RESET 0x40	/* Secondary bus reset */
-#define  PCI_BRIDGE_CTL_FAST_BACK 0x80	/* Fast Back2Back enabled on secondary interface */
-
-/* Header type 2 (CardBus bridges) */
-#define PCI_CB_CAPABILITY_LIST	0x14
-/* 0x15 reserved */
-#define PCI_CB_SEC_STATUS	0x16	/* Secondary status */
-#define PCI_CB_PRIMARY_BUS	0x18	/* PCI bus number */
-#define PCI_CB_CARD_BUS		0x19	/* CardBus bus number */
-#define PCI_CB_SUBORDINATE_BUS	0x1a	/* Subordinate bus number */
-#define PCI_CB_LATENCY_TIMER	0x1b	/* CardBus latency timer */
-#define PCI_CB_MEMORY_BASE_0	0x1c
-#define PCI_CB_MEMORY_LIMIT_0	0x20
-#define PCI_CB_MEMORY_BASE_1	0x24
-#define PCI_CB_MEMORY_LIMIT_1	0x28
-#define PCI_CB_IO_BASE_0	0x2c
-#define PCI_CB_IO_BASE_0_HI	0x2e
-#define PCI_CB_IO_LIMIT_0	0x30
-#define PCI_CB_IO_LIMIT_0_HI	0x32
-#define PCI_CB_IO_BASE_1	0x34
-#define PCI_CB_IO_BASE_1_HI	0x36
-#define PCI_CB_IO_LIMIT_1	0x38
-#define PCI_CB_IO_LIMIT_1_HI	0x3a
-#define  PCI_CB_IO_RANGE_MASK	(~0x03UL)
-/* 0x3c-0x3d are same as for htype 0 */
-#define PCI_CB_BRIDGE_CONTROL	0x3e
-#define  PCI_CB_BRIDGE_CTL_PARITY	0x01	/* Similar to standard bridge control register */
-#define  PCI_CB_BRIDGE_CTL_SERR		0x02
-#define  PCI_CB_BRIDGE_CTL_ISA		0x04
-#define  PCI_CB_BRIDGE_CTL_VGA		0x08
-#define  PCI_CB_BRIDGE_CTL_MASTER_ABORT	0x20
-#define  PCI_CB_BRIDGE_CTL_CB_RESET	0x40	/* CardBus reset */
-#define  PCI_CB_BRIDGE_CTL_16BIT_INT	0x80	/* Enable interrupt for 16-bit cards */
-#define  PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100	/* Prefetch enable for both memory regions */
-#define  PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200
-#define  PCI_CB_BRIDGE_CTL_POST_WRITES	0x400
-#define PCI_CB_SUBSYSTEM_VENDOR_ID 0x40
-#define PCI_CB_SUBSYSTEM_ID	0x42
-#define PCI_CB_LEGACY_MODE_BASE	0x44	/* 16-bit PC Card legacy mode base address (ExCa) */
-/* 0x48-0x7f reserved */
-
-/* Capability lists */
-
-#define PCI_CAP_LIST_ID		0	/* Capability ID */
-#define  PCI_CAP_ID_PM		0x01	/* Power Management */
-#define  PCI_CAP_ID_AGP		0x02	/* Accelerated Graphics Port */
-#define  PCI_CAP_ID_VPD		0x03	/* Vital Product Data */
-#define  PCI_CAP_ID_SLOTID	0x04	/* Slot Identification */
-#define  PCI_CAP_ID_MSI		0x05	/* Message Signalled Interrupts */
-#define  PCI_CAP_ID_CHSWP	0x06	/* CompactPCI HotSwap */
-#define  PCI_CAP_ID_PCIX	0x07	/* PCI-X */
-#define  PCI_CAP_ID_SHPC 	0x0C	/* PCI Standard Hot-Plug Controller */
-#define  PCI_CAP_ID_EXP 	0x10	/* PCI Express */
-#define  PCI_CAP_ID_MSIX	0x11	/* MSI-X */
-#define PCI_CAP_LIST_NEXT	1	/* Next capability in the list */
-#define PCI_CAP_FLAGS		2	/* Capability defined flags (16 bits) */
-#define PCI_CAP_SIZEOF		4
-
-/* Power Management Registers */
-
-#define PCI_PM_PMC              2       /* PM Capabilities Register */
-#define  PCI_PM_CAP_VER_MASK	0x0007	/* Version */
-#define  PCI_PM_CAP_PME_CLOCK	0x0008	/* PME clock required */
-#define  PCI_PM_CAP_RESERVED    0x0010  /* Reserved field */
-#define  PCI_PM_CAP_DSI		0x0020	/* Device specific initialization */
-#define  PCI_PM_CAP_AUX_POWER	0x01C0	/* Auxilliary power support mask */
-#define  PCI_PM_CAP_D1		0x0200	/* D1 power state support */
-#define  PCI_PM_CAP_D2		0x0400	/* D2 power state support */
-#define  PCI_PM_CAP_PME		0x0800	/* PME pin supported */
-#define  PCI_PM_CAP_PME_MASK    0xF800  /* PME Mask of all supported states */
-#define  PCI_PM_CAP_PME_D0      0x0800  /* PME# from D0 */
-#define  PCI_PM_CAP_PME_D1      0x1000  /* PME# from D1 */
-#define  PCI_PM_CAP_PME_D2      0x2000  /* PME# from D2 */
-#define  PCI_PM_CAP_PME_D3      0x4000  /* PME# from D3 (hot) */
-#define  PCI_PM_CAP_PME_D3cold  0x8000  /* PME# from D3 (cold) */
-#define PCI_PM_CTRL		4	/* PM control and status register */
-#define  PCI_PM_CTRL_STATE_MASK	0x0003	/* Current power state (D0 to D3) */
-#define  PCI_PM_CTRL_PME_ENABLE	0x0100	/* PME pin enable */
-#define  PCI_PM_CTRL_DATA_SEL_MASK	0x1e00	/* Data select (??) */
-#define  PCI_PM_CTRL_DATA_SCALE_MASK	0x6000	/* Data scale (??) */
-#define  PCI_PM_CTRL_PME_STATUS	0x8000	/* PME pin status */
-#define PCI_PM_PPB_EXTENSIONS	6	/* PPB support extensions (??) */
-#define  PCI_PM_PPB_B2_B3	0x40	/* Stop clock when in D3hot (??) */
-#define  PCI_PM_BPCC_ENABLE	0x80	/* Bus power/clock control enable (??) */
-#define PCI_PM_DATA_REGISTER	7	/* (??) */
-#define PCI_PM_SIZEOF		8
-
-/* AGP registers */
-
-#define PCI_AGP_VERSION		2	/* BCD version number */
-#define PCI_AGP_RFU		3	/* Rest of capability flags */
-#define PCI_AGP_STATUS		4	/* Status register */
-#define  PCI_AGP_STATUS_RQ_MASK	0xff000000	/* Maximum number of requests - 1 */
-#define  PCI_AGP_STATUS_SBA	0x0200	/* Sideband addressing supported */
-#define  PCI_AGP_STATUS_64BIT	0x0020	/* 64-bit addressing supported */
-#define  PCI_AGP_STATUS_FW	0x0010	/* FW transfers supported */
-#define  PCI_AGP_STATUS_RATE4	0x0004	/* 4x transfer rate supported */
-#define  PCI_AGP_STATUS_RATE2	0x0002	/* 2x transfer rate supported */
-#define  PCI_AGP_STATUS_RATE1	0x0001	/* 1x transfer rate supported */
-#define PCI_AGP_COMMAND		8	/* Control register */
-#define  PCI_AGP_COMMAND_RQ_MASK 0xff000000  /* Master: Maximum number of requests */
-#define  PCI_AGP_COMMAND_SBA	0x0200	/* Sideband addressing enabled */
-#define  PCI_AGP_COMMAND_AGP	0x0100	/* Allow processing of AGP transactions */
-#define  PCI_AGP_COMMAND_64BIT	0x0020 	/* Allow processing of 64-bit addresses */
-#define  PCI_AGP_COMMAND_FW	0x0010 	/* Force FW transfers */
-#define  PCI_AGP_COMMAND_RATE4	0x0004	/* Use 4x rate */
-#define  PCI_AGP_COMMAND_RATE2	0x0002	/* Use 2x rate */
-#define  PCI_AGP_COMMAND_RATE1	0x0001	/* Use 1x rate */
-#define PCI_AGP_SIZEOF		12
-
-/* Vital Product Data */
-
-#define PCI_VPD_ADDR		2	/* Address to access (15 bits!) */
-#define  PCI_VPD_ADDR_MASK	0x7fff	/* Address mask */
-#define  PCI_VPD_ADDR_F		0x8000	/* Write 0, 1 indicates completion */
-#define PCI_VPD_DATA		4	/* 32-bits of data returned here */
-
-/* Slot Identification */
-
-#define PCI_SID_ESR		2	/* Expansion Slot Register */
-#define  PCI_SID_ESR_NSLOTS	0x1f	/* Number of expansion slots available */
-#define  PCI_SID_ESR_FIC	0x20	/* First In Chassis Flag */
-#define PCI_SID_CHASSIS_NR	3	/* Chassis Number */
-
-/* Message Signalled Interrupts registers */
-
-#define PCI_MSI_FLAGS		2	/* Various flags */
-#define  PCI_MSI_FLAGS_64BIT	0x80	/* 64-bit addresses allowed */
-#define  PCI_MSI_FLAGS_QSIZE	0x70	/* Message queue size configured */
-#define  PCI_MSI_FLAGS_QMASK	0x0e	/* Maximum queue size available */
-#define  PCI_MSI_FLAGS_ENABLE	0x01	/* MSI feature enabled */
-#define  PCI_MSI_FLAGS_MASKBIT	0x100	/* 64-bit mask bits allowed */
-#define PCI_MSI_RFU		3	/* Rest of capability flags */
-#define PCI_MSI_ADDRESS_LO	4	/* Lower 32 bits */
-#define PCI_MSI_ADDRESS_HI	8	/* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */
-#define PCI_MSI_DATA_32		8	/* 16 bits of data for 32-bit devices */
-#define PCI_MSI_DATA_64		12	/* 16 bits of data for 64-bit devices */
-#define PCI_MSI_MASK_BIT	16	/* Mask bits register */
-
-/* CompactPCI Hotswap Register */
-
-#define PCI_CHSWP_CSR		2	/* Control and Status Register */
-#define  PCI_CHSWP_DHA		0x01	/* Device Hiding Arm */
-#define  PCI_CHSWP_EIM		0x02	/* ENUM# Signal Mask */
-#define  PCI_CHSWP_PIE		0x04	/* Pending Insert or Extract */
-#define  PCI_CHSWP_LOO		0x08	/* LED On / Off */
-#define  PCI_CHSWP_PI		0x30	/* Programming Interface */
-#define  PCI_CHSWP_EXT		0x40	/* ENUM# status - extraction */
-#define  PCI_CHSWP_INS		0x80	/* ENUM# status - insertion */
-
-/* PCI-X registers */
-
-#define PCI_X_CMD		2	/* Modes & Features */
-#define  PCI_X_CMD_DPERR_E	0x0001	/* Data Parity Error Recovery Enable */
-#define  PCI_X_CMD_ERO		0x0002	/* Enable Relaxed Ordering */
-#define  PCI_X_CMD_MAX_READ	0x000c	/* Max Memory Read Byte Count */
-#define  PCI_X_CMD_MAX_SPLIT	0x0070	/* Max Outstanding Split Transactions */
-#define  PCI_X_CMD_VERSION(x) 	(((x) >> 12) & 3) /* Version */
-#define PCI_X_STATUS		4	/* PCI-X capabilities */
-#define  PCI_X_STATUS_DEVFN	0x000000ff	/* A copy of devfn */
-#define  PCI_X_STATUS_BUS	0x0000ff00	/* A copy of bus nr */
-#define  PCI_X_STATUS_64BIT	0x00010000	/* 64-bit device */
-#define  PCI_X_STATUS_133MHZ	0x00020000	/* 133 MHz capable */
-#define  PCI_X_STATUS_SPL_DISC	0x00040000	/* Split Completion Discarded */
-#define  PCI_X_STATUS_UNX_SPL	0x00080000	/* Unexpected Split Completion */
-#define  PCI_X_STATUS_COMPLEX	0x00100000	/* Device Complexity */
-#define  PCI_X_STATUS_MAX_READ	0x00600000	/* Designed Max Memory Read Count */
-#define  PCI_X_STATUS_MAX_SPLIT	0x03800000	/* Designed Max Outstanding Split Transactions */
-#define  PCI_X_STATUS_MAX_CUM	0x1c000000	/* Designed Max Cumulative Read Size */
-#define  PCI_X_STATUS_SPL_ERR	0x20000000	/* Rcvd Split Completion Error Msg */
-#define  PCI_X_STATUS_266MHZ	0x40000000	/* 266 MHz capable */
-#define  PCI_X_STATUS_533MHZ	0x80000000	/* 533 MHz capable */
-
-/* PCI Express capability registers */
-
-#define PCI_EXP_FLAGS		2	/* Capabilities register */
-#define PCI_EXP_FLAGS_VERS	0x000f	/* Capability version */
-#define PCI_EXP_FLAGS_TYPE	0x00f0	/* Device/Port type */
-#define  PCI_EXP_TYPE_ENDPOINT	0x0	/* Express Endpoint */
-#define  PCI_EXP_TYPE_LEG_END	0x1	/* Legacy Endpoint */
-#define  PCI_EXP_TYPE_ROOT_PORT 0x4	/* Root Port */
-#define  PCI_EXP_TYPE_UPSTREAM	0x5	/* Upstream Port */
-#define  PCI_EXP_TYPE_DOWNSTREAM 0x6	/* Downstream Port */
-#define  PCI_EXP_TYPE_PCI_BRIDGE 0x7	/* PCI/PCI-X Bridge */
-#define PCI_EXP_FLAGS_SLOT	0x0100	/* Slot implemented */
-#define PCI_EXP_FLAGS_IRQ	0x3e00	/* Interrupt message number */
-#define PCI_EXP_DEVCAP		4	/* Device capabilities */
-#define  PCI_EXP_DEVCAP_PAYLOAD	0x07	/* Max_Payload_Size */
-#define  PCI_EXP_DEVCAP_PHANTOM	0x18	/* Phantom functions */
-#define  PCI_EXP_DEVCAP_EXT_TAG	0x20	/* Extended tags */
-#define  PCI_EXP_DEVCAP_L0S	0x1c0	/* L0s Acceptable Latency */
-#define  PCI_EXP_DEVCAP_L1	0xe00	/* L1 Acceptable Latency */
-#define  PCI_EXP_DEVCAP_ATN_BUT	0x1000	/* Attention Button Present */
-#define  PCI_EXP_DEVCAP_ATN_IND	0x2000	/* Attention Indicator Present */
-#define  PCI_EXP_DEVCAP_PWR_IND	0x4000	/* Power Indicator Present */
-#define  PCI_EXP_DEVCAP_PWR_VAL	0x3fc0000 /* Slot Power Limit Value */
-#define  PCI_EXP_DEVCAP_PWR_SCL	0xc000000 /* Slot Power Limit Scale */
-#define PCI_EXP_DEVCTL		8	/* Device Control */
-#define  PCI_EXP_DEVCTL_CERE	0x0001	/* Correctable Error Reporting En. */
-#define  PCI_EXP_DEVCTL_NFERE	0x0002	/* Non-Fatal Error Reporting Enable */
-#define  PCI_EXP_DEVCTL_FERE	0x0004	/* Fatal Error Reporting Enable */
-#define  PCI_EXP_DEVCTL_URRE	0x0008	/* Unsupported Request Reporting En. */
-#define  PCI_EXP_DEVCTL_RELAX_EN 0x0010 /* Enable relaxed ordering */
-#define  PCI_EXP_DEVCTL_PAYLOAD	0x00e0	/* Max_Payload_Size */
-#define  PCI_EXP_DEVCTL_EXT_TAG	0x0100	/* Extended Tag Field Enable */
-#define  PCI_EXP_DEVCTL_PHANTOM	0x0200	/* Phantom Functions Enable */
-#define  PCI_EXP_DEVCTL_AUX_PME	0x0400	/* Auxiliary Power PM Enable */
-#define  PCI_EXP_DEVCTL_NOSNOOP_EN 0x0800  /* Enable No Snoop */
-#define  PCI_EXP_DEVCTL_READRQ	0x7000	/* Max_Read_Request_Size */
-#define PCI_EXP_DEVSTA		10	/* Device Status */
-#define  PCI_EXP_DEVSTA_CED	0x01	/* Correctable Error Detected */
-#define  PCI_EXP_DEVSTA_NFED	0x02	/* Non-Fatal Error Detected */
-#define  PCI_EXP_DEVSTA_FED	0x04	/* Fatal Error Detected */
-#define  PCI_EXP_DEVSTA_URD	0x08	/* Unsupported Request Detected */
-#define  PCI_EXP_DEVSTA_AUXPD	0x10	/* AUX Power Detected */
-#define  PCI_EXP_DEVSTA_TRPND	0x20	/* Transactions Pending */
-#define PCI_EXP_LNKCAP		12	/* Link Capabilities */
-#define PCI_EXP_LNKCTL		16	/* Link Control */
-#define PCI_EXP_LNKSTA		18	/* Link Status */
-#define PCI_EXP_SLTCAP		20	/* Slot Capabilities */
-#define PCI_EXP_SLTCTL		24	/* Slot Control */
-#define PCI_EXP_SLTSTA		26	/* Slot Status */
-#define PCI_EXP_RTCTL		28	/* Root Control */
-#define  PCI_EXP_RTCTL_SECEE	0x01	/* System Error on Correctable Error */
-#define  PCI_EXP_RTCTL_SENFEE	0x02	/* System Error on Non-Fatal Error */
-#define  PCI_EXP_RTCTL_SEFEE	0x04	/* System Error on Fatal Error */
-#define  PCI_EXP_RTCTL_PMEIE	0x08	/* PME Interrupt Enable */
-#define  PCI_EXP_RTCTL_CRSSVE	0x10	/* CRS Software Visibility Enable */
-#define PCI_EXP_RTCAP		30	/* Root Capabilities */
-#define PCI_EXP_RTSTA		32	/* Root Status */
-
-/* Extended Capabilities (PCI-X 2.0 and Express) */
-#define PCI_EXT_CAP_ID(header)		(header & 0x0000ffff)
-#define PCI_EXT_CAP_VER(header)		((header >> 16) & 0xf)
-#define PCI_EXT_CAP_NEXT(header)	((header >> 20) & 0xffc)
-
-#define PCI_EXT_CAP_ID_ERR	1
-#define PCI_EXT_CAP_ID_VC	2
-#define PCI_EXT_CAP_ID_DSN	3
-#define PCI_EXT_CAP_ID_PWR	4
-
-/* Advanced Error Reporting */
-#define PCI_ERR_UNCOR_STATUS	4	/* Uncorrectable Error Status */
-#define  PCI_ERR_UNC_TRAIN	0x00000001	/* Training */
-#define  PCI_ERR_UNC_DLP	0x00000010	/* Data Link Protocol */
-#define  PCI_ERR_UNC_POISON_TLP	0x00001000	/* Poisoned TLP */
-#define  PCI_ERR_UNC_FCP	0x00002000	/* Flow Control Protocol */
-#define  PCI_ERR_UNC_COMP_TIME	0x00004000	/* Completion Timeout */
-#define  PCI_ERR_UNC_COMP_ABORT	0x00008000	/* Completer Abort */
-#define  PCI_ERR_UNC_UNX_COMP	0x00010000	/* Unexpected Completion */
-#define  PCI_ERR_UNC_RX_OVER	0x00020000	/* Receiver Overflow */
-#define  PCI_ERR_UNC_MALF_TLP	0x00040000	/* Malformed TLP */
-#define  PCI_ERR_UNC_ECRC	0x00080000	/* ECRC Error Status */
-#define  PCI_ERR_UNC_UNSUP	0x00100000	/* Unsupported Request */
-#define PCI_ERR_UNCOR_MASK	8	/* Uncorrectable Error Mask */
-	/* Same bits as above */
-#define PCI_ERR_UNCOR_SEVER	12	/* Uncorrectable Error Severity */
-	/* Same bits as above */
-#define PCI_ERR_COR_STATUS	16	/* Correctable Error Status */
-#define  PCI_ERR_COR_RCVR	0x00000001	/* Receiver Error Status */
-#define  PCI_ERR_COR_BAD_TLP	0x00000040	/* Bad TLP Status */
-#define  PCI_ERR_COR_BAD_DLLP	0x00000080	/* Bad DLLP Status */
-#define  PCI_ERR_COR_REP_ROLL	0x00000100	/* REPLAY_NUM Rollover */
-#define  PCI_ERR_COR_REP_TIMER	0x00001000	/* Replay Timer Timeout */
-#define PCI_ERR_COR_MASK	20	/* Correctable Error Mask */
-	/* Same bits as above */
-#define PCI_ERR_CAP		24	/* Advanced Error Capabilities */
-#define  PCI_ERR_CAP_FEP(x)	((x) & 31)	/* First Error Pointer */
-#define  PCI_ERR_CAP_ECRC_GENC	0x00000020	/* ECRC Generation Capable */
-#define  PCI_ERR_CAP_ECRC_GENE	0x00000040	/* ECRC Generation Enable */
-#define  PCI_ERR_CAP_ECRC_CHKC	0x00000080	/* ECRC Check Capable */
-#define  PCI_ERR_CAP_ECRC_CHKE	0x00000100	/* ECRC Check Enable */
-#define PCI_ERR_HEADER_LOG	28	/* Header Log Register (16 bytes) */
-#define PCI_ERR_ROOT_COMMAND	44	/* Root Error Command */
-#define PCI_ERR_ROOT_STATUS	48
-#define PCI_ERR_ROOT_COR_SRC	52
-#define PCI_ERR_ROOT_SRC	54
-
-/* Virtual Channel */
-#define PCI_VC_PORT_REG1	4
-#define PCI_VC_PORT_REG2	8
-#define PCI_VC_PORT_CTRL	12
-#define PCI_VC_PORT_STATUS	14
-#define PCI_VC_RES_CAP		16
-#define PCI_VC_RES_CTRL		20
-#define PCI_VC_RES_STATUS	26
-
-/* Power Budgeting */
-#define PCI_PWR_DSR		4	/* Data Select Register */
-#define PCI_PWR_DATA		8	/* Data Register */
-#define  PCI_PWR_DATA_BASE(x)	((x) & 0xff)	    /* Base Power */
-#define  PCI_PWR_DATA_SCALE(x)	(((x) >> 8) & 3)    /* Data Scale */
-#define  PCI_PWR_DATA_PM_SUB(x)	(((x) >> 10) & 7)   /* PM Sub State */
-#define  PCI_PWR_DATA_PM_STATE(x) (((x) >> 13) & 3) /* PM State */
-#define  PCI_PWR_DATA_TYPE(x)	(((x) >> 15) & 7)   /* Type */
-#define  PCI_PWR_DATA_RAIL(x)	(((x) >> 18) & 7)   /* Power Rail */
-#define PCI_PWR_CAP		12	/* Capability */
-#define  PCI_PWR_CAP_BUDGET(x)	((x) & 1)	/* Included in system budget */
+/* Include the pci register defines */
+#include <linux/pci_regs.h>
 
 /* Include the ID list */
-
 #include <linux/pci_ids.h>
 
 /*
@@ -496,9 +70,9 @@ enum pci_mmap_state {
 
 typedef int __bitwise pci_power_t;
 
-#define PCI_D0	((pci_power_t __force) 0)
-#define PCI_D1	((pci_power_t __force) 1)
-#define PCI_D2	((pci_power_t __force) 2)
+#define PCI_D0		((pci_power_t __force) 0)
+#define PCI_D1		((pci_power_t __force) 1)
+#define PCI_D2		((pci_power_t __force) 2)
 #define PCI_D3hot	((pci_power_t __force) 3)
 #define PCI_D3cold	((pci_power_t __force) 4)
 #define PCI_POWER_ERROR	((pci_power_t __force) -1)
@@ -577,15 +151,15 @@ struct pci_dev {
  *	7-10	bridges: address space assigned to buses behind the bridge
  */
 
-#define PCI_ROM_RESOURCE 6
-#define PCI_BRIDGE_RESOURCES 7
-#define PCI_NUM_RESOURCES 11
+#define PCI_ROM_RESOURCE	6
+#define PCI_BRIDGE_RESOURCES	7
+#define PCI_NUM_RESOURCES	11
 
 #ifndef PCI_BUS_NUM_RESOURCES
-#define PCI_BUS_NUM_RESOURCES 8
+#define PCI_BUS_NUM_RESOURCES	8
 #endif
-  
-#define PCI_REGION_FLAG_MASK 0x0fU	/* These bits of resource flags tell us the PCI region flags */
+
+#define PCI_REGION_FLAG_MASK	0x0fU	/* These bits of resource flags tell us the PCI region flags */
 
 struct pci_bus {
 	struct list_head node;		/* node in list of buses */
@@ -694,7 +268,7 @@ struct pci_driver {
  * @dev_class_mask: the class mask for this device
  *
  * This macro is used to create a struct pci_device_id that matches a
- * specific PCI class.  The vendor, device, subvendor, and subdevice 
+ * specific PCI class.  The vendor, device, subvendor, and subdevice
  * fields will be set to PCI_ANY_ID.
  */
 #define PCI_DEVICE_CLASS(dev_class,dev_class_mask) \
@@ -702,7 +276,7 @@ struct pci_driver {
 	.vendor = PCI_ANY_ID, .device = PCI_ANY_ID, \
 	.subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID
 
-/* 
+/*
  * pci_module_init is obsolete, this stays here till we fix up all usages of it
  * in the tree.
  */
@@ -905,18 +479,26 @@ extern void pci_disable_msix(struct pci_dev *dev);
 extern void msi_remove_pci_irq_vectors(struct pci_dev *dev);
 #endif
 
-#endif /* CONFIG_PCI */
-
-/* Include architecture-dependent settings and functions */
+/*
+ * PCI domain support.  Sometimes called PCI segment (eg by ACPI),
+ * a PCI domain is defined to be a set of PCI busses which share
+ * configuration space.
+ */
+#ifndef CONFIG_PCI_DOMAINS
+static inline int pci_domain_nr(struct pci_bus *bus) { return 0; }
+static inline int pci_proc_domain(struct pci_bus *bus)
+{
+	return 0;
+}
+#endif
 
-#include <asm/pci.h>
+#else /* CONFIG_PCI is not enabled */
 
 /*
  *  If the system does not have PCI, clearly these return errors.  Define
  *  these as simple inline functions to avoid hair in drivers.
  */
 
-#ifndef CONFIG_PCI
 #define _PCI_NOP(o,s,t) \
 	static inline int pci_##o##_config_##s (struct pci_dev *dev, int where, t val) \
 		{ return PCIBIOS_FUNC_NOT_SUPPORTED; }
@@ -967,21 +549,11 @@ static inline int pci_enable_wake(struct pci_dev *dev, pci_power_t state, int en
 
 #define pci_dma_burst_advice(pdev, strat, strategy_parameter) do { } while (0)
 
-#else
+#endif /* CONFIG_PCI */
 
-/*
- * PCI domain support.  Sometimes called PCI segment (eg by ACPI),
- * a PCI domain is defined to be a set of PCI busses which share
- * configuration space.
- */
-#ifndef CONFIG_PCI_DOMAINS
-static inline int pci_domain_nr(struct pci_bus *bus) { return 0; }
-static inline int pci_proc_domain(struct pci_bus *bus)
-{
-	return 0;
-}
-#endif
-#endif /* !CONFIG_PCI */
+/* Include architecture-dependent settings and functions */
+
+#include <asm/pci.h>
 
 /* these helpers provide future and backwards compatibility
  * for accessing popular PCI BAR info */
diff --git a/include/linux/pci_regs.h b/include/linux/pci_regs.h
new file mode 100644
index 00000000000..7dc391cad10
--- /dev/null
+++ b/include/linux/pci_regs.h
@@ -0,0 +1,447 @@
+/*
+ *	pci_regs.h
+ *
+ *	PCI standard defines
+ *	Copyright 1994, Drew Eckhardt
+ *	Copyright 1997--1999 Martin Mares <mj@ucw.cz>
+ *
+ *	For more information, please consult the following manuals (look at
+ *	http://www.pcisig.com/ for how to get them):
+ *
+ *	PCI BIOS Specification
+ *	PCI Local Bus Specification
+ *	PCI to PCI Bridge Specification
+ *	PCI System Design Guide
+ */
+
+#ifndef LINUX_PCI_REGS_H
+#define LINUX_PCI_REGS_H
+
+/*
+ * Under PCI, each device has 256 bytes of configuration address space,
+ * of which the first 64 bytes are standardized as follows:
+ */
+#define PCI_VENDOR_ID		0x00	/* 16 bits */
+#define PCI_DEVICE_ID		0x02	/* 16 bits */
+#define PCI_COMMAND		0x04	/* 16 bits */
+#define  PCI_COMMAND_IO		0x1	/* Enable response in I/O space */
+#define  PCI_COMMAND_MEMORY	0x2	/* Enable response in Memory space */
+#define  PCI_COMMAND_MASTER	0x4	/* Enable bus mastering */
+#define  PCI_COMMAND_SPECIAL	0x8	/* Enable response to special cycles */
+#define  PCI_COMMAND_INVALIDATE	0x10	/* Use memory write and invalidate */
+#define  PCI_COMMAND_VGA_PALETTE 0x20	/* Enable palette snooping */
+#define  PCI_COMMAND_PARITY	0x40	/* Enable parity checking */
+#define  PCI_COMMAND_WAIT 	0x80	/* Enable address/data stepping */
+#define  PCI_COMMAND_SERR	0x100	/* Enable SERR */
+#define  PCI_COMMAND_FAST_BACK	0x200	/* Enable back-to-back writes */
+#define  PCI_COMMAND_INTX_DISABLE 0x400 /* INTx Emulation Disable */
+
+#define PCI_STATUS		0x06	/* 16 bits */
+#define  PCI_STATUS_CAP_LIST	0x10	/* Support Capability List */
+#define  PCI_STATUS_66MHZ	0x20	/* Support 66 Mhz PCI 2.1 bus */
+#define  PCI_STATUS_UDF		0x40	/* Support User Definable Features [obsolete] */
+#define  PCI_STATUS_FAST_BACK	0x80	/* Accept fast-back to back */
+#define  PCI_STATUS_PARITY	0x100	/* Detected parity error */
+#define  PCI_STATUS_DEVSEL_MASK	0x600	/* DEVSEL timing */
+#define  PCI_STATUS_DEVSEL_FAST		0x000
+#define  PCI_STATUS_DEVSEL_MEDIUM	0x200
+#define  PCI_STATUS_DEVSEL_SLOW		0x400
+#define  PCI_STATUS_SIG_TARGET_ABORT	0x800 /* Set on target abort */
+#define  PCI_STATUS_REC_TARGET_ABORT	0x1000 /* Master ack of " */
+#define  PCI_STATUS_REC_MASTER_ABORT	0x2000 /* Set on master abort */
+#define  PCI_STATUS_SIG_SYSTEM_ERROR	0x4000 /* Set when we drive SERR */
+#define  PCI_STATUS_DETECTED_PARITY	0x8000 /* Set on parity error */
+
+#define PCI_CLASS_REVISION	0x08	/* High 24 bits are class, low 8 revision */
+#define PCI_REVISION_ID		0x08	/* Revision ID */
+#define PCI_CLASS_PROG		0x09	/* Reg. Level Programming Interface */
+#define PCI_CLASS_DEVICE	0x0a	/* Device class */
+
+#define PCI_CACHE_LINE_SIZE	0x0c	/* 8 bits */
+#define PCI_LATENCY_TIMER	0x0d	/* 8 bits */
+#define PCI_HEADER_TYPE		0x0e	/* 8 bits */
+#define  PCI_HEADER_TYPE_NORMAL		0
+#define  PCI_HEADER_TYPE_BRIDGE		1
+#define  PCI_HEADER_TYPE_CARDBUS	2
+
+#define PCI_BIST		0x0f	/* 8 bits */
+#define  PCI_BIST_CODE_MASK	0x0f	/* Return result */
+#define  PCI_BIST_START		0x40	/* 1 to start BIST, 2 secs or less */
+#define  PCI_BIST_CAPABLE	0x80	/* 1 if BIST capable */
+
+/*
+ * Base addresses specify locations in memory or I/O space.
+ * Decoded size can be determined by writing a value of
+ * 0xffffffff to the register, and reading it back.  Only
+ * 1 bits are decoded.
+ */
+#define PCI_BASE_ADDRESS_0	0x10	/* 32 bits */
+#define PCI_BASE_ADDRESS_1	0x14	/* 32 bits [htype 0,1 only] */
+#define PCI_BASE_ADDRESS_2	0x18	/* 32 bits [htype 0 only] */
+#define PCI_BASE_ADDRESS_3	0x1c	/* 32 bits */
+#define PCI_BASE_ADDRESS_4	0x20	/* 32 bits */
+#define PCI_BASE_ADDRESS_5	0x24	/* 32 bits */
+#define  PCI_BASE_ADDRESS_SPACE		0x01	/* 0 = memory, 1 = I/O */
+#define  PCI_BASE_ADDRESS_SPACE_IO	0x01
+#define  PCI_BASE_ADDRESS_SPACE_MEMORY	0x00
+#define  PCI_BASE_ADDRESS_MEM_TYPE_MASK	0x06
+#define  PCI_BASE_ADDRESS_MEM_TYPE_32	0x00	/* 32 bit address */
+#define  PCI_BASE_ADDRESS_MEM_TYPE_1M	0x02	/* Below 1M [obsolete] */
+#define  PCI_BASE_ADDRESS_MEM_TYPE_64	0x04	/* 64 bit address */
+#define  PCI_BASE_ADDRESS_MEM_PREFETCH	0x08	/* prefetchable? */
+#define  PCI_BASE_ADDRESS_MEM_MASK	(~0x0fUL)
+#define  PCI_BASE_ADDRESS_IO_MASK	(~0x03UL)
+/* bit 1 is reserved if address_space = 1 */
+
+/* Header type 0 (normal devices) */
+#define PCI_CARDBUS_CIS		0x28
+#define PCI_SUBSYSTEM_VENDOR_ID	0x2c
+#define PCI_SUBSYSTEM_ID	0x2e
+#define PCI_ROM_ADDRESS		0x30	/* Bits 31..11 are address, 10..1 reserved */
+#define  PCI_ROM_ADDRESS_ENABLE	0x01
+#define PCI_ROM_ADDRESS_MASK	(~0x7ffUL)
+
+#define PCI_CAPABILITY_LIST	0x34	/* Offset of first capability list entry */
+
+/* 0x35-0x3b are reserved */
+#define PCI_INTERRUPT_LINE	0x3c	/* 8 bits */
+#define PCI_INTERRUPT_PIN	0x3d	/* 8 bits */
+#define PCI_MIN_GNT		0x3e	/* 8 bits */
+#define PCI_MAX_LAT		0x3f	/* 8 bits */
+
+/* Header type 1 (PCI-to-PCI bridges) */
+#define PCI_PRIMARY_BUS		0x18	/* Primary bus number */
+#define PCI_SECONDARY_BUS	0x19	/* Secondary bus number */
+#define PCI_SUBORDINATE_BUS	0x1a	/* Highest bus number behind the bridge */
+#define PCI_SEC_LATENCY_TIMER	0x1b	/* Latency timer for secondary interface */
+#define PCI_IO_BASE		0x1c	/* I/O range behind the bridge */
+#define PCI_IO_LIMIT		0x1d
+#define  PCI_IO_RANGE_TYPE_MASK	0x0fUL	/* I/O bridging type */
+#define  PCI_IO_RANGE_TYPE_16	0x00
+#define  PCI_IO_RANGE_TYPE_32	0x01
+#define  PCI_IO_RANGE_MASK	(~0x0fUL)
+#define PCI_SEC_STATUS		0x1e	/* Secondary status register, only bit 14 used */
+#define PCI_MEMORY_BASE		0x20	/* Memory range behind */
+#define PCI_MEMORY_LIMIT	0x22
+#define  PCI_MEMORY_RANGE_TYPE_MASK 0x0fUL
+#define  PCI_MEMORY_RANGE_MASK	(~0x0fUL)
+#define PCI_PREF_MEMORY_BASE	0x24	/* Prefetchable memory range behind */
+#define PCI_PREF_MEMORY_LIMIT	0x26
+#define  PCI_PREF_RANGE_TYPE_MASK 0x0fUL
+#define  PCI_PREF_RANGE_TYPE_32	0x00
+#define  PCI_PREF_RANGE_TYPE_64	0x01
+#define  PCI_PREF_RANGE_MASK	(~0x0fUL)
+#define PCI_PREF_BASE_UPPER32	0x28	/* Upper half of prefetchable memory range */
+#define PCI_PREF_LIMIT_UPPER32	0x2c
+#define PCI_IO_BASE_UPPER16	0x30	/* Upper half of I/O addresses */
+#define PCI_IO_LIMIT_UPPER16	0x32
+/* 0x34 same as for htype 0 */
+/* 0x35-0x3b is reserved */
+#define PCI_ROM_ADDRESS1	0x38	/* Same as PCI_ROM_ADDRESS, but for htype 1 */
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_BRIDGE_CONTROL	0x3e
+#define  PCI_BRIDGE_CTL_PARITY	0x01	/* Enable parity detection on secondary interface */
+#define  PCI_BRIDGE_CTL_SERR	0x02	/* The same for SERR forwarding */
+#define  PCI_BRIDGE_CTL_NO_ISA	0x04	/* Disable bridging of ISA ports */
+#define  PCI_BRIDGE_CTL_VGA	0x08	/* Forward VGA addresses */
+#define  PCI_BRIDGE_CTL_MASTER_ABORT	0x20  /* Report master aborts */
+#define  PCI_BRIDGE_CTL_BUS_RESET	0x40	/* Secondary bus reset */
+#define  PCI_BRIDGE_CTL_FAST_BACK	0x80	/* Fast Back2Back enabled on secondary interface */
+
+/* Header type 2 (CardBus bridges) */
+#define PCI_CB_CAPABILITY_LIST	0x14
+/* 0x15 reserved */
+#define PCI_CB_SEC_STATUS	0x16	/* Secondary status */
+#define PCI_CB_PRIMARY_BUS	0x18	/* PCI bus number */
+#define PCI_CB_CARD_BUS		0x19	/* CardBus bus number */
+#define PCI_CB_SUBORDINATE_BUS	0x1a	/* Subordinate bus number */
+#define PCI_CB_LATENCY_TIMER	0x1b	/* CardBus latency timer */
+#define PCI_CB_MEMORY_BASE_0	0x1c
+#define PCI_CB_MEMORY_LIMIT_0	0x20
+#define PCI_CB_MEMORY_BASE_1	0x24
+#define PCI_CB_MEMORY_LIMIT_1	0x28
+#define PCI_CB_IO_BASE_0	0x2c
+#define PCI_CB_IO_BASE_0_HI	0x2e
+#define PCI_CB_IO_LIMIT_0	0x30
+#define PCI_CB_IO_LIMIT_0_HI	0x32
+#define PCI_CB_IO_BASE_1	0x34
+#define PCI_CB_IO_BASE_1_HI	0x36
+#define PCI_CB_IO_LIMIT_1	0x38
+#define PCI_CB_IO_LIMIT_1_HI	0x3a
+#define  PCI_CB_IO_RANGE_MASK	(~0x03UL)
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_CB_BRIDGE_CONTROL	0x3e
+#define  PCI_CB_BRIDGE_CTL_PARITY	0x01	/* Similar to standard bridge control register */
+#define  PCI_CB_BRIDGE_CTL_SERR		0x02
+#define  PCI_CB_BRIDGE_CTL_ISA		0x04
+#define  PCI_CB_BRIDGE_CTL_VGA		0x08
+#define  PCI_CB_BRIDGE_CTL_MASTER_ABORT	0x20
+#define  PCI_CB_BRIDGE_CTL_CB_RESET	0x40	/* CardBus reset */
+#define  PCI_CB_BRIDGE_CTL_16BIT_INT	0x80	/* Enable interrupt for 16-bit cards */
+#define  PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100	/* Prefetch enable for both memory regions */
+#define  PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200
+#define  PCI_CB_BRIDGE_CTL_POST_WRITES	0x400
+#define PCI_CB_SUBSYSTEM_VENDOR_ID	0x40
+#define PCI_CB_SUBSYSTEM_ID		0x42
+#define PCI_CB_LEGACY_MODE_BASE		0x44	/* 16-bit PC Card legacy mode base address (ExCa) */
+/* 0x48-0x7f reserved */
+
+/* Capability lists */
+
+#define PCI_CAP_LIST_ID		0	/* Capability ID */
+#define  PCI_CAP_ID_PM		0x01	/* Power Management */
+#define  PCI_CAP_ID_AGP		0x02	/* Accelerated Graphics Port */
+#define  PCI_CAP_ID_VPD		0x03	/* Vital Product Data */
+#define  PCI_CAP_ID_SLOTID	0x04	/* Slot Identification */
+#define  PCI_CAP_ID_MSI		0x05	/* Message Signalled Interrupts */
+#define  PCI_CAP_ID_CHSWP	0x06	/* CompactPCI HotSwap */
+#define  PCI_CAP_ID_PCIX	0x07	/* PCI-X */
+#define  PCI_CAP_ID_SHPC 	0x0C	/* PCI Standard Hot-Plug Controller */
+#define  PCI_CAP_ID_EXP 	0x10	/* PCI Express */
+#define  PCI_CAP_ID_MSIX	0x11	/* MSI-X */
+#define PCI_CAP_LIST_NEXT	1	/* Next capability in the list */
+#define PCI_CAP_FLAGS		2	/* Capability defined flags (16 bits) */
+#define PCI_CAP_SIZEOF		4
+
+/* Power Management Registers */
+
+#define PCI_PM_PMC		2	/* PM Capabilities Register */
+#define  PCI_PM_CAP_VER_MASK	0x0007	/* Version */
+#define  PCI_PM_CAP_PME_CLOCK	0x0008	/* PME clock required */
+#define  PCI_PM_CAP_RESERVED    0x0010  /* Reserved field */
+#define  PCI_PM_CAP_DSI		0x0020	/* Device specific initialization */
+#define  PCI_PM_CAP_AUX_POWER	0x01C0	/* Auxilliary power support mask */
+#define  PCI_PM_CAP_D1		0x0200	/* D1 power state support */
+#define  PCI_PM_CAP_D2		0x0400	/* D2 power state support */
+#define  PCI_PM_CAP_PME		0x0800	/* PME pin supported */
+#define  PCI_PM_CAP_PME_MASK	0xF800	/* PME Mask of all supported states */
+#define  PCI_PM_CAP_PME_D0	0x0800	/* PME# from D0 */
+#define  PCI_PM_CAP_PME_D1	0x1000	/* PME# from D1 */
+#define  PCI_PM_CAP_PME_D2	0x2000	/* PME# from D2 */
+#define  PCI_PM_CAP_PME_D3	0x4000	/* PME# from D3 (hot) */
+#define  PCI_PM_CAP_PME_D3cold	0x8000	/* PME# from D3 (cold) */
+#define PCI_PM_CTRL		4	/* PM control and status register */
+#define  PCI_PM_CTRL_STATE_MASK	0x0003	/* Current power state (D0 to D3) */
+#define  PCI_PM_CTRL_PME_ENABLE	0x0100	/* PME pin enable */
+#define  PCI_PM_CTRL_DATA_SEL_MASK	0x1e00	/* Data select (??) */
+#define  PCI_PM_CTRL_DATA_SCALE_MASK	0x6000	/* Data scale (??) */
+#define  PCI_PM_CTRL_PME_STATUS	0x8000	/* PME pin status */
+#define PCI_PM_PPB_EXTENSIONS	6	/* PPB support extensions (??) */
+#define  PCI_PM_PPB_B2_B3	0x40	/* Stop clock when in D3hot (??) */
+#define  PCI_PM_BPCC_ENABLE	0x80	/* Bus power/clock control enable (??) */
+#define PCI_PM_DATA_REGISTER	7	/* (??) */
+#define PCI_PM_SIZEOF		8
+
+/* AGP registers */
+
+#define PCI_AGP_VERSION		2	/* BCD version number */
+#define PCI_AGP_RFU		3	/* Rest of capability flags */
+#define PCI_AGP_STATUS		4	/* Status register */
+#define  PCI_AGP_STATUS_RQ_MASK	0xff000000	/* Maximum number of requests - 1 */
+#define  PCI_AGP_STATUS_SBA	0x0200	/* Sideband addressing supported */
+#define  PCI_AGP_STATUS_64BIT	0x0020	/* 64-bit addressing supported */
+#define  PCI_AGP_STATUS_FW	0x0010	/* FW transfers supported */
+#define  PCI_AGP_STATUS_RATE4	0x0004	/* 4x transfer rate supported */
+#define  PCI_AGP_STATUS_RATE2	0x0002	/* 2x transfer rate supported */
+#define  PCI_AGP_STATUS_RATE1	0x0001	/* 1x transfer rate supported */
+#define PCI_AGP_COMMAND		8	/* Control register */
+#define  PCI_AGP_COMMAND_RQ_MASK 0xff000000  /* Master: Maximum number of requests */
+#define  PCI_AGP_COMMAND_SBA	0x0200	/* Sideband addressing enabled */
+#define  PCI_AGP_COMMAND_AGP	0x0100	/* Allow processing of AGP transactions */
+#define  PCI_AGP_COMMAND_64BIT	0x0020 	/* Allow processing of 64-bit addresses */
+#define  PCI_AGP_COMMAND_FW	0x0010 	/* Force FW transfers */
+#define  PCI_AGP_COMMAND_RATE4	0x0004	/* Use 4x rate */
+#define  PCI_AGP_COMMAND_RATE2	0x0002	/* Use 2x rate */
+#define  PCI_AGP_COMMAND_RATE1	0x0001	/* Use 1x rate */
+#define PCI_AGP_SIZEOF		12
+
+/* Vital Product Data */
+
+#define PCI_VPD_ADDR		2	/* Address to access (15 bits!) */
+#define  PCI_VPD_ADDR_MASK	0x7fff	/* Address mask */
+#define  PCI_VPD_ADDR_F		0x8000	/* Write 0, 1 indicates completion */
+#define PCI_VPD_DATA		4	/* 32-bits of data returned here */
+
+/* Slot Identification */
+
+#define PCI_SID_ESR		2	/* Expansion Slot Register */
+#define  PCI_SID_ESR_NSLOTS	0x1f	/* Number of expansion slots available */
+#define  PCI_SID_ESR_FIC	0x20	/* First In Chassis Flag */
+#define PCI_SID_CHASSIS_NR	3	/* Chassis Number */
+
+/* Message Signalled Interrupts registers */
+
+#define PCI_MSI_FLAGS		2	/* Various flags */
+#define  PCI_MSI_FLAGS_64BIT	0x80	/* 64-bit addresses allowed */
+#define  PCI_MSI_FLAGS_QSIZE	0x70	/* Message queue size configured */
+#define  PCI_MSI_FLAGS_QMASK	0x0e	/* Maximum queue size available */
+#define  PCI_MSI_FLAGS_ENABLE	0x01	/* MSI feature enabled */
+#define  PCI_MSI_FLAGS_MASKBIT	0x100	/* 64-bit mask bits allowed */
+#define PCI_MSI_RFU		3	/* Rest of capability flags */
+#define PCI_MSI_ADDRESS_LO	4	/* Lower 32 bits */
+#define PCI_MSI_ADDRESS_HI	8	/* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */
+#define PCI_MSI_DATA_32		8	/* 16 bits of data for 32-bit devices */
+#define PCI_MSI_DATA_64		12	/* 16 bits of data for 64-bit devices */
+#define PCI_MSI_MASK_BIT	16	/* Mask bits register */
+
+/* CompactPCI Hotswap Register */
+
+#define PCI_CHSWP_CSR		2	/* Control and Status Register */
+#define  PCI_CHSWP_DHA		0x01	/* Device Hiding Arm */
+#define  PCI_CHSWP_EIM		0x02	/* ENUM# Signal Mask */
+#define  PCI_CHSWP_PIE		0x04	/* Pending Insert or Extract */
+#define  PCI_CHSWP_LOO		0x08	/* LED On / Off */
+#define  PCI_CHSWP_PI		0x30	/* Programming Interface */
+#define  PCI_CHSWP_EXT		0x40	/* ENUM# status - extraction */
+#define  PCI_CHSWP_INS		0x80	/* ENUM# status - insertion */
+
+/* PCI-X registers */
+
+#define PCI_X_CMD		2	/* Modes & Features */
+#define  PCI_X_CMD_DPERR_E	0x0001	/* Data Parity Error Recovery Enable */
+#define  PCI_X_CMD_ERO		0x0002	/* Enable Relaxed Ordering */
+#define  PCI_X_CMD_MAX_READ	0x000c	/* Max Memory Read Byte Count */
+#define  PCI_X_CMD_MAX_SPLIT	0x0070	/* Max Outstanding Split Transactions */
+#define  PCI_X_CMD_VERSION(x) 	(((x) >> 12) & 3) /* Version */
+#define PCI_X_STATUS		4	/* PCI-X capabilities */
+#define  PCI_X_STATUS_DEVFN	0x000000ff	/* A copy of devfn */
+#define  PCI_X_STATUS_BUS	0x0000ff00	/* A copy of bus nr */
+#define  PCI_X_STATUS_64BIT	0x00010000	/* 64-bit device */
+#define  PCI_X_STATUS_133MHZ	0x00020000	/* 133 MHz capable */
+#define  PCI_X_STATUS_SPL_DISC	0x00040000	/* Split Completion Discarded */
+#define  PCI_X_STATUS_UNX_SPL	0x00080000	/* Unexpected Split Completion */
+#define  PCI_X_STATUS_COMPLEX	0x00100000	/* Device Complexity */
+#define  PCI_X_STATUS_MAX_READ	0x00600000	/* Designed Max Memory Read Count */
+#define  PCI_X_STATUS_MAX_SPLIT	0x03800000	/* Designed Max Outstanding Split Transactions */
+#define  PCI_X_STATUS_MAX_CUM	0x1c000000	/* Designed Max Cumulative Read Size */
+#define  PCI_X_STATUS_SPL_ERR	0x20000000	/* Rcvd Split Completion Error Msg */
+#define  PCI_X_STATUS_266MHZ	0x40000000	/* 266 MHz capable */
+#define  PCI_X_STATUS_533MHZ	0x80000000	/* 533 MHz capable */
+
+/* PCI Express capability registers */
+
+#define PCI_EXP_FLAGS		2	/* Capabilities register */
+#define PCI_EXP_FLAGS_VERS	0x000f	/* Capability version */
+#define PCI_EXP_FLAGS_TYPE	0x00f0	/* Device/Port type */
+#define  PCI_EXP_TYPE_ENDPOINT	0x0	/* Express Endpoint */
+#define  PCI_EXP_TYPE_LEG_END	0x1	/* Legacy Endpoint */
+#define  PCI_EXP_TYPE_ROOT_PORT 0x4	/* Root Port */
+#define  PCI_EXP_TYPE_UPSTREAM	0x5	/* Upstream Port */
+#define  PCI_EXP_TYPE_DOWNSTREAM 0x6	/* Downstream Port */
+#define  PCI_EXP_TYPE_PCI_BRIDGE 0x7	/* PCI/PCI-X Bridge */
+#define PCI_EXP_FLAGS_SLOT	0x0100	/* Slot implemented */
+#define PCI_EXP_FLAGS_IRQ	0x3e00	/* Interrupt message number */
+#define PCI_EXP_DEVCAP		4	/* Device capabilities */
+#define  PCI_EXP_DEVCAP_PAYLOAD	0x07	/* Max_Payload_Size */
+#define  PCI_EXP_DEVCAP_PHANTOM	0x18	/* Phantom functions */
+#define  PCI_EXP_DEVCAP_EXT_TAG	0x20	/* Extended tags */
+#define  PCI_EXP_DEVCAP_L0S	0x1c0	/* L0s Acceptable Latency */
+#define  PCI_EXP_DEVCAP_L1	0xe00	/* L1 Acceptable Latency */
+#define  PCI_EXP_DEVCAP_ATN_BUT	0x1000	/* Attention Button Present */
+#define  PCI_EXP_DEVCAP_ATN_IND	0x2000	/* Attention Indicator Present */
+#define  PCI_EXP_DEVCAP_PWR_IND	0x4000	/* Power Indicator Present */
+#define  PCI_EXP_DEVCAP_PWR_VAL	0x3fc0000 /* Slot Power Limit Value */
+#define  PCI_EXP_DEVCAP_PWR_SCL	0xc000000 /* Slot Power Limit Scale */
+#define PCI_EXP_DEVCTL		8	/* Device Control */
+#define  PCI_EXP_DEVCTL_CERE	0x0001	/* Correctable Error Reporting En. */
+#define  PCI_EXP_DEVCTL_NFERE	0x0002	/* Non-Fatal Error Reporting Enable */
+#define  PCI_EXP_DEVCTL_FERE	0x0004	/* Fatal Error Reporting Enable */
+#define  PCI_EXP_DEVCTL_URRE	0x0008	/* Unsupported Request Reporting En. */
+#define  PCI_EXP_DEVCTL_RELAX_EN 0x0010 /* Enable relaxed ordering */
+#define  PCI_EXP_DEVCTL_PAYLOAD	0x00e0	/* Max_Payload_Size */
+#define  PCI_EXP_DEVCTL_EXT_TAG	0x0100	/* Extended Tag Field Enable */
+#define  PCI_EXP_DEVCTL_PHANTOM	0x0200	/* Phantom Functions Enable */
+#define  PCI_EXP_DEVCTL_AUX_PME	0x0400	/* Auxiliary Power PM Enable */
+#define  PCI_EXP_DEVCTL_NOSNOOP_EN 0x0800  /* Enable No Snoop */
+#define  PCI_EXP_DEVCTL_READRQ	0x7000	/* Max_Read_Request_Size */
+#define PCI_EXP_DEVSTA		10	/* Device Status */
+#define  PCI_EXP_DEVSTA_CED	0x01	/* Correctable Error Detected */
+#define  PCI_EXP_DEVSTA_NFED	0x02	/* Non-Fatal Error Detected */
+#define  PCI_EXP_DEVSTA_FED	0x04	/* Fatal Error Detected */
+#define  PCI_EXP_DEVSTA_URD	0x08	/* Unsupported Request Detected */
+#define  PCI_EXP_DEVSTA_AUXPD	0x10	/* AUX Power Detected */
+#define  PCI_EXP_DEVSTA_TRPND	0x20	/* Transactions Pending */
+#define PCI_EXP_LNKCAP		12	/* Link Capabilities */
+#define PCI_EXP_LNKCTL		16	/* Link Control */
+#define PCI_EXP_LNKSTA		18	/* Link Status */
+#define PCI_EXP_SLTCAP		20	/* Slot Capabilities */
+#define PCI_EXP_SLTCTL		24	/* Slot Control */
+#define PCI_EXP_SLTSTA		26	/* Slot Status */
+#define PCI_EXP_RTCTL		28	/* Root Control */
+#define  PCI_EXP_RTCTL_SECEE	0x01	/* System Error on Correctable Error */
+#define  PCI_EXP_RTCTL_SENFEE	0x02	/* System Error on Non-Fatal Error */
+#define  PCI_EXP_RTCTL_SEFEE	0x04	/* System Error on Fatal Error */
+#define  PCI_EXP_RTCTL_PMEIE	0x08	/* PME Interrupt Enable */
+#define  PCI_EXP_RTCTL_CRSSVE	0x10	/* CRS Software Visibility Enable */
+#define PCI_EXP_RTCAP		30	/* Root Capabilities */
+#define PCI_EXP_RTSTA		32	/* Root Status */
+
+/* Extended Capabilities (PCI-X 2.0 and Express) */
+#define PCI_EXT_CAP_ID(header)		(header & 0x0000ffff)
+#define PCI_EXT_CAP_VER(header)		((header >> 16) & 0xf)
+#define PCI_EXT_CAP_NEXT(header)	((header >> 20) & 0xffc)
+
+#define PCI_EXT_CAP_ID_ERR	1
+#define PCI_EXT_CAP_ID_VC	2
+#define PCI_EXT_CAP_ID_DSN	3
+#define PCI_EXT_CAP_ID_PWR	4
+
+/* Advanced Error Reporting */
+#define PCI_ERR_UNCOR_STATUS	4	/* Uncorrectable Error Status */
+#define  PCI_ERR_UNC_TRAIN	0x00000001	/* Training */
+#define  PCI_ERR_UNC_DLP	0x00000010	/* Data Link Protocol */
+#define  PCI_ERR_UNC_POISON_TLP	0x00001000	/* Poisoned TLP */
+#define  PCI_ERR_UNC_FCP	0x00002000	/* Flow Control Protocol */
+#define  PCI_ERR_UNC_COMP_TIME	0x00004000	/* Completion Timeout */
+#define  PCI_ERR_UNC_COMP_ABORT	0x00008000	/* Completer Abort */
+#define  PCI_ERR_UNC_UNX_COMP	0x00010000	/* Unexpected Completion */
+#define  PCI_ERR_UNC_RX_OVER	0x00020000	/* Receiver Overflow */
+#define  PCI_ERR_UNC_MALF_TLP	0x00040000	/* Malformed TLP */
+#define  PCI_ERR_UNC_ECRC	0x00080000	/* ECRC Error Status */
+#define  PCI_ERR_UNC_UNSUP	0x00100000	/* Unsupported Request */
+#define PCI_ERR_UNCOR_MASK	8	/* Uncorrectable Error Mask */
+	/* Same bits as above */
+#define PCI_ERR_UNCOR_SEVER	12	/* Uncorrectable Error Severity */
+	/* Same bits as above */
+#define PCI_ERR_COR_STATUS	16	/* Correctable Error Status */
+#define  PCI_ERR_COR_RCVR	0x00000001	/* Receiver Error Status */
+#define  PCI_ERR_COR_BAD_TLP	0x00000040	/* Bad TLP Status */
+#define  PCI_ERR_COR_BAD_DLLP	0x00000080	/* Bad DLLP Status */
+#define  PCI_ERR_COR_REP_ROLL	0x00000100	/* REPLAY_NUM Rollover */
+#define  PCI_ERR_COR_REP_TIMER	0x00001000	/* Replay Timer Timeout */
+#define PCI_ERR_COR_MASK	20	/* Correctable Error Mask */
+	/* Same bits as above */
+#define PCI_ERR_CAP		24	/* Advanced Error Capabilities */
+#define  PCI_ERR_CAP_FEP(x)	((x) & 31)	/* First Error Pointer */
+#define  PCI_ERR_CAP_ECRC_GENC	0x00000020	/* ECRC Generation Capable */
+#define  PCI_ERR_CAP_ECRC_GENE	0x00000040	/* ECRC Generation Enable */
+#define  PCI_ERR_CAP_ECRC_CHKC	0x00000080	/* ECRC Check Capable */
+#define  PCI_ERR_CAP_ECRC_CHKE	0x00000100	/* ECRC Check Enable */
+#define PCI_ERR_HEADER_LOG	28	/* Header Log Register (16 bytes) */
+#define PCI_ERR_ROOT_COMMAND	44	/* Root Error Command */
+#define PCI_ERR_ROOT_STATUS	48
+#define PCI_ERR_ROOT_COR_SRC	52
+#define PCI_ERR_ROOT_SRC	54
+
+/* Virtual Channel */
+#define PCI_VC_PORT_REG1	4
+#define PCI_VC_PORT_REG2	8
+#define PCI_VC_PORT_CTRL	12
+#define PCI_VC_PORT_STATUS	14
+#define PCI_VC_RES_CAP		16
+#define PCI_VC_RES_CTRL		20
+#define PCI_VC_RES_STATUS	26
+
+/* Power Budgeting */
+#define PCI_PWR_DSR		4	/* Data Select Register */
+#define PCI_PWR_DATA		8	/* Data Register */
+#define  PCI_PWR_DATA_BASE(x)	((x) & 0xff)	    /* Base Power */
+#define  PCI_PWR_DATA_SCALE(x)	(((x) >> 8) & 3)    /* Data Scale */
+#define  PCI_PWR_DATA_PM_SUB(x)	(((x) >> 10) & 7)   /* PM Sub State */
+#define  PCI_PWR_DATA_PM_STATE(x) (((x) >> 13) & 3) /* PM State */
+#define  PCI_PWR_DATA_TYPE(x)	(((x) >> 15) & 7)   /* Type */
+#define  PCI_PWR_DATA_RAIL(x)	(((x) >> 18) & 7)   /* Power Rail */
+#define PCI_PWR_CAP		12	/* Capability */
+#define  PCI_PWR_CAP_BUDGET(x)	((x) & 1)	/* Included in system budget */
+
+#endif /* LINUX_PCI_REGS_H */