bcma: add serial console support

This adds support for serial console to bcma, when operating on an SoC.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

4 files changed, 83 insertions, 0 deletions

diff --git a/drivers/bcma/bcma_private.h b/drivers/bcma/bcma_private.h
index b97633d0d23..22d3052e190 100644
--- a/drivers/bcma/bcma_private.h
+++ b/drivers/bcma/bcma_private.h
@@ -29,6 +29,14 @@ void bcma_init_bus(struct bcma_bus *bus);
 /* sprom.c */
 int bcma_sprom_get(struct bcma_bus *bus);
 
+/* driver_chipcommon.c */
+#ifdef CONFIG_BCMA_DRIVER_MIPS
+void bcma_chipco_serial_init(struct bcma_drv_cc *cc);
+#endif /* CONFIG_BCMA_DRIVER_MIPS */
+
+/* driver_chipcommon_pmu.c */
+u32 bcma_pmu_alp_clock(struct bcma_drv_cc *cc);
+
 #ifdef CONFIG_BCMA_HOST_PCI
 /* host_pci.c */
 extern int __init bcma_host_pci_init(void);
diff --git a/drivers/bcma/driver_chipcommon.c b/drivers/bcma/driver_chipcommon.c
index acca327db3d..47cce9d6963 100644
--- a/drivers/bcma/driver_chipcommon.c
+++ b/drivers/bcma/driver_chipcommon.c
@@ -106,3 +106,51 @@ u32 bcma_chipco_gpio_polarity(struct bcma_drv_cc *cc, u32 mask, u32 value)
 {
 	return bcma_cc_write32_masked(cc, BCMA_CC_GPIOPOL, mask, value);
 }
+
+#ifdef CONFIG_BCMA_DRIVER_MIPS
+void bcma_chipco_serial_init(struct bcma_drv_cc *cc)
+{
+	unsigned int irq;
+	u32 baud_base;
+	u32 i;
+	unsigned int ccrev = cc->core->id.rev;
+	struct bcma_serial_port *ports = cc->serial_ports;
+
+	if (ccrev >= 11 && ccrev != 15) {
+		/* Fixed ALP clock */
+		baud_base = bcma_pmu_alp_clock(cc);
+		if (ccrev >= 21) {
+			/* Turn off UART clock before switching clocksource. */
+			bcma_cc_write32(cc, BCMA_CC_CORECTL,
+				       bcma_cc_read32(cc, BCMA_CC_CORECTL)
+				       & ~BCMA_CC_CORECTL_UARTCLKEN);
+		}
+		/* Set the override bit so we don't divide it */
+		bcma_cc_write32(cc, BCMA_CC_CORECTL,
+			       bcma_cc_read32(cc, BCMA_CC_CORECTL)
+			       | BCMA_CC_CORECTL_UARTCLK0);
+		if (ccrev >= 21) {
+			/* Re-enable the UART clock. */
+			bcma_cc_write32(cc, BCMA_CC_CORECTL,
+				       bcma_cc_read32(cc, BCMA_CC_CORECTL)
+				       | BCMA_CC_CORECTL_UARTCLKEN);
+		}
+	} else {
+		pr_err("serial not supported on this device ccrev: 0x%x\n",
+		       ccrev);
+		return;
+	}
+
+	irq = bcma_core_mips_irq(cc->core);
+
+	/* Determine the registers of the UARTs */
+	cc->nr_serial_ports = (cc->capabilities & BCMA_CC_CAP_NRUART);
+	for (i = 0; i < cc->nr_serial_ports; i++) {
+		ports[i].regs = cc->core->io_addr + BCMA_CC_UART0_DATA +
+				(i * 256);
+		ports[i].irq = irq;
+		ports[i].baud_base = baud_base;
+		ports[i].reg_shift = 0;
+	}
+}
+#endif /* CONFIG_BCMA_DRIVER_MIPS */
diff --git a/drivers/bcma/driver_chipcommon_pmu.c b/drivers/bcma/driver_chipcommon_pmu.c
index fcc63db0ce7..354caeea639 100644
--- a/drivers/bcma/driver_chipcommon_pmu.c
+++ b/drivers/bcma/driver_chipcommon_pmu.c
@@ -136,3 +136,29 @@ void bcma_pmu_init(struct bcma_drv_cc *cc)
 	bcma_pmu_swreg_init(cc);
 	bcma_pmu_workarounds(cc);
 }
+
+u32 bcma_pmu_alp_clock(struct bcma_drv_cc *cc)
+{
+	struct bcma_bus *bus = cc->core->bus;
+
+	switch (bus->chipinfo.id) {
+	case 0x4716:
+	case 0x4748:
+	case 47162:
+	case 0x4313:
+	case 0x5357:
+	case 0x4749:
+	case 53572:
+		/* always 20Mhz */
+		return 20000 * 1000;
+	case 0x5356:
+	case 0x5300:
+		/* always 25Mhz */
+		return 25000 * 1000;
+	default:
+		pr_warn("No ALP clock specified for %04X device, "
+			"pmu rev. %d, using default %d Hz\n",
+			bus->chipinfo.id, cc->pmu.rev, BCMA_CC_PMU_ALP_CLOCK);
+	}
+	return BCMA_CC_PMU_ALP_CLOCK;
+}
diff --git a/drivers/bcma/driver_mips.c b/drivers/bcma/driver_mips.c
index 4b60c9f9583..b17233cb75c 100644
--- a/drivers/bcma/driver_mips.c
+++ b/drivers/bcma/driver_mips.c
@@ -238,6 +238,7 @@ void bcma_core_mips_init(struct bcma_drv_mips *mcore)
 	if (mcore->setup_done)
 		return;
 
+	bcma_chipco_serial_init(&bus->drv_cc);
 	bcma_core_mips_flash_detect(mcore);
 	mcore->setup_done = true;
 }