summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2011-01-10target-sh4: improve TLBAurelien Jarno1-21/+44
SH4 is using 16-bit instructions which means most of the constants are loaded through a constant pool at the end of the subroutine. The same memory page is therefore accessed in exec and read mode. With the current implementation, a QEMU TLB entry is set to read or read/write mode after an UTLB search and to exec mode after an ITLB search, which causes a lot of TLB exceptions to switch from read or read/write to exec and vice versa. This patch optimizes that by already setting the QEMU TLB entry in read or read/write mode when an UTLB entry is copied into ITLB (during an ITLB miss). This improve the emulation speed by about 14%. Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-09target-sh4: implement writes to mmaped ITLBAurelien Jarno3-0/+23
Some Linux kernels seems to implement ITLB/UTLB flushing through by writing all TLB entries through the memory mapped interface instead of writing one to MMUCR.TI. Implement memory mapped ITLB write interface so that such kernels can boot. This fixes https://bugs.launchpad.net/bugs/700774 . Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-09tcg: fix typo in readmeMike Frysinger1-1/+1
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
2011-01-09tcg/README: Spelling fixesStefan Weil1-4/+4
Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
2011-01-09qemu-tech: Spelling fixesStefan Weil1-2/+2
Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
2011-01-09qemu-doc: Spelling fixesStefan Weil1-10/+10
neccessary -> necessary Keberos -> Kerberos emuilated -> emulated transciever -> transceiver emulaton -> emulation inital -> initial MingGW -> MinGW Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
2011-01-09qemu-doc: Add missing blanksStefan Weil1-2/+2
Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
2011-01-09qemu-doc: Add missing menu entryStefan Weil1-0/+2
Each @section should have a menu entry and a @node entry. Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
2011-01-09qemu-doc: Clean whitespaceStefan Weil1-2/+2
Remove blanks at line endings. Signed-off-by: Stefan Weil <weil@mail.berlios.de> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
2011-01-09usb-bsd: fix a file descriptor leakBlue Swirl1-32/+39
Fix a file descriptor leak reported by cppcheck: [/src/qemu/usb-bsd.c:392]: (error) Resource leak: bfd [/src/qemu/usb-bsd.c:388]: (error) Resource leak: dfd Rearrange the code to avoid descriptor leaks. Also add braces as needed. Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
2011-01-09alsaaudio: add endianness support for VoiceInMichael Walle1-7/+27
Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: malc <av1474@comtv.ru>
2011-01-09ossaudio: add endianness support for VoiceInMichael Walle1-5/+15
Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: malc <av1474@comtv.ru>
2011-01-08tcg/mips: fix branch target change during code retranslationAurelien Jarno1-1/+1
TCG on MIPS was trying to avoid changing the branch offset, but didn't due to a stupid typo. Fix it. Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-08tcg/arm: fix qemu_st64 for big endian targetsAurelien Jarno1-1/+1
Due to a typo, qemu_st64 doesn't properly byteswap the 32-bit low word of a 64 bit word before saving it. This patch fixes that. Acked-by: Andrzej Zaborowski <balrogg@gmail.com> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-08tcg/arm: fix branch target change during code retranslationAurelien Jarno1-8/+20
QEMU uses code retranslation to restore the CPU state when an exception happens. For it to work the retranslation must not modify the generated code. This is what is currently implemented in ARM TCG. However on CPU that don't have icache/dcache/memory synchronised like ARM, this requirement is stronger and code retranslation must not modify the generated code "atomically", as the cache line might be flushed at any moment (interrupt, exception, task switching), even if not triggered by QEMU. The probability for this to happen is very low, and depends on cache size and associativiy, machine load, interrupts, so the symptoms are might happen randomly. This requirement is currently not followed in tcg/arm, for the load/store code, which basically has the following structure: 1) tlb access code is written 2) conditional fast path code is written 3) branch is written with a temporary target 4) slow path code is written 5) branch target is updated The cache lines corresponding to the retranslated code is not flushed after code retranslation as the generated code is supposed to be the same. However if the cache line corresponding to the branch instruction is flushed between step 3 and 5, and is not flushed again before the code is executed again, the branch target is wrong. In the guest, the symptoms are MMU page fault at a random addresses, which leads to kernel page fault or segmentation faults. The patch fixes this issue by avoiding writing the branch target until it is known, that is by writing only the branch instruction first, and later only the offset. This fixes booting linux guests on ARM hosts (tested: arm, i386, mips, mipsel, sh4, sparc). Acked-by: Edgar E. Iglesias <edgar.iglesias@gmail.com> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-08Merge branch 'linux-user-for-upstream' of git://gitorious.org/qemu-maemo/qemuAurelien Jarno13-46/+238
* 'linux-user-for-upstream' of git://gitorious.org/qemu-maemo/qemu: Remove dead code for ARM semihosting commandline handling Fix commandline handling for ARM semihosted executables linux-user: Fix incorrect NaN detection in ARM nwfpe emulation softfloat: Implement floatx80_is_any_nan() and float128_is_any_nan() linux-user: Implement FS_IOC_FIEMAP ioctl linux-user: Support ioctls whose parameter size is not constant linux-user: Implement sync_file_range{,2} syscalls
2011-01-07Remove dead code for ARM semihosting commandline handlingWolfgang Schildbach4-6/+0
There are some bits in the code which were used to store the commandline for the semihosting call. These bits are now write-only and can be removed. Signed-off-by: Wolfgang Schildbach <wschi@dolby.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
2011-01-07Fix commandline handling for ARM semihosted executablesWolfgang Schildbach1-30/+49
Use the copy of the command line that loader_build_argptr() sets up in guest memory as the command line to return from the ARM SYS_GET_CMDLINE semihosting call. Previously we were using a pointer to memory which had already been freed before the guest program started. This fixes https://bugs.launchpad.net/qemu/+bug/673613 . Signed-off-by: Wolfgang Schildbach <wschi@dolby.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
2011-01-07linux-user: Fix incorrect NaN detection in ARM nwfpe emulationPeter Maydell1-7/+7
The code in the linux-user ARM nwfpe emulation was incorrectly checking only for quiet NaNs when it should have been checking for any kind of NaN. This is probably because the code in question was taken from the Linux kernel, whose copy of the softfloat library had been modified so that float*_is_nan() returned true for all NaNs, not just quiet ones. The qemu equivalent function is float*_is_any_nan(), so use that. NB that this code is really obsolete since nobody uses FPE for actual arithmetic now; this is just cleanup following the recent renaming of the NaN related functions. Acked-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
2011-01-07softfloat: Implement floatx80_is_any_nan() and float128_is_any_nan()Peter Maydell1-0/+11
Implement versions of float*_is_any_nan() for the floatx80 and float128 types. Acked-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
2011-01-07linux-user: Implement FS_IOC_FIEMAP ioctlPeter Maydell4-0/+109
Implement the FS_IOC_FIEMAP ioctl using the new support for custom handling of ioctls; this is needed because the struct that is passed includes a variable-length array. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
2011-01-07linux-user: Support ioctls whose parameter size is not constantPeter Maydell1-3/+15
Some ioctls (for example FS_IOC_FIEMAP) use structures whose size is not constant. The generic argument conversion code in do_ioctl() cannot handle this, so add support for implementing a special-case handler for a particular ioctl which does the conversion itself. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
2011-01-07cris: Allow more TB chaningEdgar E. Iglesias1-19/+22
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
2011-01-07linux-user: Implement sync_file_range{,2} syscallsPeter Maydell3-0/+47
Implement the missing syscalls sync_file_range and sync_file_range2. The latter in particular is used by newer versions of apt on Ubuntu for ARM. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
2011-01-07cris: Avoid useless tmp in t_gen_cc_jmp()Edgar E. Iglesias1-6/+1
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
2011-01-06cirrus: delete GCC 4.6 warningsAurelien Jarno1-3/+3
Commit 92d675d1c1f23f3617e24b63c825074a1d1da44b triggered uninitialized variables warning with GCC 4.6. Fix them by adding zero initializers. Acked-by: Blue Swirl <blauwirbel@gmail.com> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06target-arm: wire up the softfloat flush_input_to_zero flagPeter Maydell1-1/+7
Wire up the new softfloat support for flushing input denormals to zero on ARM. The FPSCR FZ bit enables flush-to-zero for both inputs and outputs, but the reporting of when inputs are flushed to zero is via a separate IDC bit rather than the UFC (underflow) bit used when output denormals are flushed to zero. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Acked-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06target-arm: Set softfloat cumulative exc flags from correct FPSCR bitsPeter Maydell1-1/+1
When handling a write to the ARM FPSCR, set the softfloat cumulative exception flags from the cumulative flags in the FPSCR, not the exception-enable bits. Also don't apply a mask: vfp_exceptbits_to_host will only look at the correct bits anyway. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Acked-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06softfloat: Implement flushing input denormals to zeroPeter Maydell2-3/+123
Add support to softfloat for flushing input denormal float32 and float64 to zero. softfloat's existing 'flush_to_zero' flag only flushes denormals to zero on output. Some CPUs need input denormals to be flushed before processing as well. Implement this, using a new status flag to enable it and a new exception status bit to indicate when it has happened. Existing CPUs should be unaffected as there is no behaviour change unless the mode is enabled. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Acked-by: Aurelien Jarno <aurelien@aurel32.net> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06target-arm: fix SMMLA/SMMLS instructionsAurelien Jarno1-45/+51
SMMLA and SMMLS are broken on both in normal and thumb mode, that is both (different) implementations are wrong. They try to avoid a 64-bit add for the rounding, which is not trivial if you want to support both SMMLA and SMMLS with the same code. The code below uses the same implementation for both modes, using the code from the ARM manual. It also fixes the thumb decoding that was a mix between normal and thumb mode. This fixes the issues reported in https://bugs.launchpad.net/qemu/+bug/629298 Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06block: delete a write-only variableBlue Swirl1-5/+0
Avoid a warning with GCC 4.6.0: /src/qemu/block.c: In function 'bdrv_img_create': /src/qemu/block.c:2862:25: error: variable 'fmt' set but not used [-Werror=unused-but-set-variable] CC: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
2011-01-06cirrus_vga: Declare as little endianBlue Swirl1-100/+12
This patch replaces explicit bswaps with endianness hints to the mmio layer. CC: Alexander Graf <agraf@suse.de> Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
2011-01-06pc: move port 92 stuff back to pc.c from pckbd.cBlue Swirl2-20/+88
956a3e6bb7386de48b642d4fee11f7f86a2fcf9a introduced a bug concerning reset bit for port 92. Since the keyboard output port and port 92 are not compatible anyway, let's separate them. Reported-by: Peter Lieven <pl@dlh.net> Signed-off-by: Blue Swirl <blauwirbel@gmail.com> -- v2: added reset handler and VMState
2011-01-06target-ppc: Implement correct NaN propagation rulesAurelien Jarno1-2/+17
Implement the correct NaN propagation rules for PowerPC targets by providing an appropriate pickNaN function. Also fix the #ifdef tests for default NaN definition, the correct name is TARGET_PPC instead of TARGET_POWERPC. Reviewed-by: Nathan Froyd <froydnj@codesourcery.com> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06target-mips: Implement correct NaN propagation rulesAurelien Jarno1-0/+27
Implement the correct NaN propagation rules for MIPS targets by providing an appropriate pickNaN function. Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06softfloat: use float{32,64,x80,128}_maybe_silence_nan()Aurelien Jarno1-43/+16
Use float{32,64,x80,128}_maybe_silence_nan() instead of toggling the sNaN bit manually. This allow per target implementation of sNaN to qNaN conversion. Signed-off-by: Aurelien Jarno <aurelien@aurel32.net> Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
2011-01-06softfloat: add float{x80,128}_maybe_silence_nan()Aurelien Jarno2-0/+48
Add float{x80,128}_maybe_silence_nan() functions, they will be need by propagateFloat{x80,128}NaN(). Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06softfloat: fix float{32,64}_maybe_silence_nan() for MIPSAurelien Jarno1-6/+14
On targets that define sNaN with the sNaN bit as one, simply clearing this bit may correspond to an infinite value. Convert it to a default NaN if SNAN_BIT_IS_ONE, as it corresponds to the MIPS implementation, the only emulated CPU with SNAN_BIT_IS_ONE. When other CPU of this type are added, this might be updated to include more cases. Acked-by: Alexander Graf <agraf@suse.de> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06softfloat: rename *IsNaN variables to *IsQuietNaNAurelien Jarno1-16/+20
Similarly to what has been done in commit 185698715dfb18c82ad2a5dbc169908602d43e81 rename the misnamed *IsNaN variables into *IsQuietNaN. Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06softfloat: remove HPPA specific codeAurelien Jarno1-5/+1
We don't have any HPPA target, so let's remove HPPA specific code. It can be re-added when someone adds an HPPA target. This has been blessed by Stuart Brady <sdb@zubnet.me.uk>, author of the target-hppa fork. Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06target-ppc: use float32_is_any_nan()Aurelien Jarno1-3/+2
Use the new function float32_is_any_nan() instead of float32_is_quiet_nan() || float32_is_signaling_nan(). Acked-by: Alexander Graf <agraf@suse.de> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06target-ppc: fix default qNaNAurelien Jarno1-2/+2
On PPC the default qNaN doesn't have the sign bit set. Acked-by: Alexander Graf <agraf@suse.de> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-06target-ppc: remove PRECISE_EMULATION defineAurelien Jarno2-50/+11
The PRECISE_EMULATION is "hardcoded" to one in target-ppc/exec.h and not something easily tunable. Remove it and non-precise emulation code as it doesn't make a noticeable difference in speed. People wanting speed improvement should use softfloat-native instead. Acked-by: Alexander Graf <agraf@suse.de> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-05microblaze: Use more TB chainingEdgar E. Iglesias1-5/+23
For some workloads with tight loops this ~doubles the emulation speed. Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
2011-01-04cirrus_vga: fix division by 0 for color expansion ropAurelien Jarno1-32/+33
Commit d85d0d3883f5a567fa2969a0396e42e0a662b3fa introduces a regression with Windows ME that leads to a division by 0 and a crash. It uses the color expansion rop with the source pitch set to 0. This is something allowed, as the manual explicitely says "When the source of color-expand data is display memory, the source pitch is ignored.". This patch fixes this regression by computing sx, sy and others variables only if they are going to be used later, that is for a plain copy ROP. It basically consists in moving code. Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-04Fix curses on big endian hostsAurelien Jarno2-4/+4
On big endian hosts, the curses interface is unusable: the emulated graphic card only displays garbage, while the monitor interface displays nothing (or rather only spaces). The curses interface is waiting for data in native endianness, so console_write_ch() should not do any conversion. The conversion should be done when reading the video buffer in hw/vga.c. I supposed this buffer is in little endian mode, though it's not impossible that the data is actually in guest endianness. I currently have no big endian guest to way (they all switch to graphic mode immediately). Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-04noaudio: correctly account acquired samplesMichael Walle1-0/+3
This will fix the return value of the function which otherwise returns too many samples because sw->total_hw_samples_acquired isn't correctly accounted. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: malc <av1474@comtv.ru>
2011-01-02target-arm: Implement correct NaN propagation rulesPeter Maydell1-0/+23
Implement the correct NaN propagation rules for ARM targets by providing an appropriate pickNaN function. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-02softfloat: abstract out target-specific NaN propagation rulesPeter Maydell1-60/+100
IEEE754 doesn't specify precisely what NaN should be returned as the result of an operation on two input NaNs. This is therefore target-specific. Abstract out the code in propagateFloat*NaN() which was implementing the x87 propagation rules, so that it can be easily replaced on a per-target basis. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
2011-01-02softfloat: Rename float*_is_nan() functions to float*_is_quiet_nan()Peter Maydell10-67/+67
The softfloat functions float*_is_nan() were badly misnamed, because they return true only for quiet NaNs, not for all NaNs. Rename them to float*_is_quiet_nan() to more accurately reflect what they do. This change was produced by: perl -p -i -e 's/_is_nan/_is_quiet_nan/g' $(git grep -l is_nan) (with the results manually checked.) Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Nathan Froyd <froydnj@codesourcery.com> Acked-by: Edgar E. Iglesias <edgar.iglesias@gmail.com> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-27 16:25:08 +0000