summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2011-09-21Linux 3.1-rc7v3.1-rc7Linus Torvalds1-1/+1
2011-09-21XZ: Fix incorrect XZ_BUF_ERRORLasse Collin1-7/+20
xz_dec_run() could incorrectly return XZ_BUF_ERROR if all of the following was true: - The caller knows how many bytes of output to expect and only provides that much output space. - When the last output bytes are decoded, the caller-provided input buffer ends right before the LZMA2 end of payload marker. So LZMA2 won't provide more output anymore, but it won't know it yet and thus won't return XZ_STREAM_END yet. - A BCJ filter is in use and it hasn't left any unfiltered bytes in the temp buffer. This can happen with any BCJ filter, but in practice it's more likely with filters other than the x86 BCJ. This fixes <https://bugzilla.redhat.com/show_bug.cgi?id=735408> where Squashfs thinks that a valid file system is corrupt. This also fixes a similar bug in single-call mode where the uncompressed size of a block using BCJ + LZMA2 was 0 bytes and caller provided no output space. Many empty .xz files don't contain any blocks and thus don't trigger this bug. This also tweaks a closely related detail: xz_dec_bcj_run() could call xz_dec_lzma2_run() to decode into temp buffer when it was known to be useless. This was harmless although it wasted a minuscule number of CPU cycles. Signed-off-by: Lasse Collin <lasse.collin@tukaani.org> Cc: stable <stable@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-21Merge git://github.com/davem330/netLinus Torvalds22-80/+165
* git://github.com/davem330/net: (27 commits) xfrm: Perform a replay check after return from async codepaths fib:fix BUG_ON in fib_nl_newrule when add new fib rule ixgbe: fix possible null buffer error tg3: fix VLAN tagging regression net: pxa168: Fix build errors by including interrupt.h netconsole: switch init_netconsole() to late_initcall gianfar: Fix overflow check and return value for gfar_get_cls_all() ppp_generic: fix multilink fragment MTU calculation (again) GRETH: avoid overwrite IP-stack's IP-frags checksum GRETH: RX/TX bytes were never increased ipv6: fix a possible double free b43: Fix beacon problem in ad-hoc mode Bluetooth: add support for 2011 mac mini Bluetooth: Add MacBookAir4,1 support Bluetooth: Fixed BT ST Channel reg order r8169: do not enable the TBI for anything but the original 8169. r8169: remove erroneous processing of always set bit. r8169: fix WOL setting for 8105 and 8111evl r8169: add MODULE_FIRMWARE for the firmware of 8111evl r8169: fix the reset setting for 8111evl ...
2011-09-21Merge branch 'for-linus' of git://git.kernel.dk/linux-blockLinus Torvalds21-78/+92
* 'for-linus' of git://git.kernel.dk/linux-block: floppy: use del_timer_sync() in init cleanup blk-cgroup: be able to remove the record of unplugged device block: Don't check QUEUE_FLAG_SAME_COMP in __blk_complete_request mm: Add comment explaining task state setting in bdi_forker_thread() mm: Cleanup clearing of BDI_pending bit in bdi_forker_thread() block: simplify force plug flush code a little bit block: change force plug flush call order block: Fix queue_flag update when rq_affinity goes from 2 to 1 block: separate priority boosting from REQ_META block: remove READ_META and WRITE_META xen-blkback: fixed indentation and comments xen-blkback: Don't disconnect backend until state switched to XenbusStateClosed.
2011-09-21init: carefully handle loglevel option on kernel cmdline.Alexander Sverdlin1-2/+13
When a malformed loglevel value (for example "${abc}") is passed on the kernel cmdline, the loglevel itself is being set to 0. That then suppresses all following messages, including all the errors and crashes caused by other malformed cmdline options. This could make debugging process quite tricky. This patch leaves the previous value of loglevel if the new value is incorrect and reports an error code in this case. Signed-off-by: Alexander Sverdlin <alexander.sverdlin@sysgo.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-21teach /proc/$pid/numa_maps about transparent hugepagesDave Hansen1-0/+20
This is modeled after the smaps code. It detects transparent hugepages and then does a single gather_stats() for the page as a whole. This has two benifits: 1. It is more efficient since it does many pages in a single shot. 2. It does not have to break down the huge page. Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-21break out numa_maps gather_pte_stats() checksDave Hansen1-15/+24
gather_pte_stats() does a number of checks on a target page to see whether it should even be considered for statistics. This breaks that code out in to a separate function so that we can use it in the transparent hugepage case in the next patch. Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Acked-by: Hugh Dickins <hughd@google.com> Reviewed-by: Christoph Lameter <cl@gentwo.org> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-21make /proc/$pid/numa_maps gather_stats() take variable page sizeDave Hansen1-10/+11
We need to teach the numa_maps code about transparent huge pages. The first step is to teach gather_stats() that the pte it is dealing with might represent more than one page. Note that will we use this in a moment for transparent huge pages since they have use a single pmd_t which _acts_ as a "surrogate" for a bunch of smaller pte_t's. I'm a _bit_ unhappy that this interface counts in hugetlbfs page sizes for hugetlbfs pages and PAGE_SIZE for normal pages. That means that to figure out how many _bytes_ "dirty=1" means, you must first know the hugetlbfs page size. That's easier said than done especially if you don't have visibility in to the mount. But, that's probably a discussion for another day especially since it would change behavior to fix it. But, just in case anyone wonders why this patch only passes a '1' in the hugetlb case... Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-21xfrm: Perform a replay check after return from async codepathsSteffen Klassert1-0/+5
When asyncronous crypto algorithms are used, there might be many packets that passed the xfrm replay check, but the replay advance function is not called yet for these packets. So the replay check function would accept a replay of all of these packets. Also the system might crash if there are more packets in async processing than the size of the anti replay window, because the replay advance function would try to update the replay window beyond the bounds. This pach adds a second replay check after resuming from the async processing to fix these issues. Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-21fib:fix BUG_ON in fib_nl_newrule when add new fib ruleGao feng1-2/+2
add new fib rule can cause BUG_ON happen the reproduce shell is ip rule add pref 38 ip rule add pref 38 ip rule add to 192.168.3.0/24 goto 38 ip rule del pref 38 ip rule add to 192.168.3.0/24 goto 38 ip rule add pref 38 then the BUG_ON will happen del BUG_ON and use (ctarget == NULL) identify whether this rule is unresolved Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-21floppy: use del_timer_sync() in init cleanupCarsten Emde1-4/+4
When no floppy is found the module code can be released while a timer function is pending or about to be executed. CPU0 CPU1 floppy_init() timer_softirq() spin_lock_irq(&base->lock); detach_timer(); spin_unlock_irq(&base->lock); -> Interrupt del_timer(); return -ENODEV; module_cleanup(); <- EOI call_timer_fn(); OOPS Use del_timer_sync() to prevent this. Signed-off-by: Carsten Emde <C.Emde@osadl.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2011-09-21blk-cgroup: be able to remove the record of unplugged deviceWanlong Gao1-21/+16
The bug is we're not able to remove the device from blkio cgroup's per-device control files if it gets unplugged. To reproduce the bug: # mount -t cgroup -o blkio xxx /cgroup # cd /cgroup # echo "8:0 1000" > blkio.throttle.read_bps_device # unplug the device # cat blkio.throttle.read_bps_device 8:0 1000 # echo "8:0 0" > blkio.throttle.read_bps_device -bash: echo: write error: No such device After patching, the device removal will succeed. Thanks for the comments of Paul, Zefan, and Vivek. Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Paul Menage <paul@paulmenage.org> Acked-by: Vivek Goyal <vgoyal@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2011-09-21ixgbe: fix possible null buffer errorJesse Brandeburg1-2/+2
It seems that at least one PPC machine would occasionally give a (valid) 0 as the return value from dma_map, this caused the ixgbe code to not work correctly. A fix is pending in the PPC tree to not return 0 from dma map, but we can also fix the driver to make sure we don't mess up in other arches as well. This patch is applicable to all current stable kernels. Ref: https://bugzilla.redhat.com/show_bug.cgi?id=683611 Reported-by: Neil Horman <nhorman@redhat.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Alexander Duyck <alexander.h.duyck@intel.com> CC: stable@kernel.org Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-21tg3: fix VLAN tagging regressionKasper Pedersen1-2/+0
commit 92cd3a17ce9c719abb4c28dee3438e0c641f8de4 tg3: Simplify tx bd assignments broke VLAN tagging on outbound packets. It ifdef'ed BCM_KERNEL_SUPPORTS_8021Q, but this is not set anywhere. So vlan never gets set, and all packets are sent with vlan=0. v2: We can just remove the test. vlan_tx_tag_present is valid regardless of whether the 802.1q module is built. Tested on BCM5721 rev 11. Signed-off-by: Kasper Pedersen <kernel@kasperkp.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20Merge branch 'fixes' of git://git.linaro.org/people/arnd/arm-socLinus Torvalds13-65/+52
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc: mach-integrator: fix VGA base regression arm/dt: Tegra: Update SDHCI nodes to match bindings ARM: EXYNOS4: fix incorrect pad configuration for keypad row lines ARM: SAMSUNG: fix to prevent declaring duplicated ARM: SAMSUNG: fix watchdog reset issue with clk_get() ARM: S3C64XX: Remove un-used code backlight code on SMDK6410 ARM: EXYNOS4: restart clocksource while system resumes ARM: EXYNOS4: Fix routing timer interrupt to offline CPU ARM: EXYNOS4: Fix return type of local_timer_setup() ARM: EXYNOS4: Fix wrong pll type for vpll ARM: Dove: fix second SPI initialization call
2011-09-20Merge branch 'for-linus' of git://github.com/chrismason/linuxLinus Torvalds1-1/+6
* 'for-linus' of git://github.com/chrismason/linux: Btrfs: reserve sufficient space for ioctl clone
2011-09-20staging: zcache: fix cleancache crashSeth Jennings1-1/+1
After commit c5f5c4db3938 ("staging: zcache: fix crash on high memory swap") cleancache crashes on the first successful get. This was caused by a remaining virt_to_page() call in zcache_pampd_get_data_and_free() that only gets run in the cleancache path. The patch converts the virt_to_page() to struct page casting like was done for other instances in c5f5c4db3938. Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com> Tested-By: Valdis Kletnieks <valdis.kletnieks@vt.edu> Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-20mach-integrator: fix VGA base regressionLinus Walleij2-2/+2
The changes introduced in commit cc22b4c18540e5e8bf55c7d124044f9317527d3c "ARM: set vga memory base at run-time" Makes the Integrator/AP freeze completely. I appears that this is due to the VGA base address being assigned at PCI init time, while this base is needed earlier than that. Moving the initialization of the base address to the .map_io function solves this problem. Cc: Rob Herring <rob.herring@calxeda.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-09-20arm/dt: Tegra: Update SDHCI nodes to match bindingsStephen Warren2-9/+9
The bindings were recently updated to have separate properties for each type of GPIO. Update the Device Tree source to match that. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-09-20net: pxa168: Fix build errors by including interrupt.hTanmay Upadhyay1-0/+1
Commit a6b7a407865aab9f849dd99a71072b7cd1175116 removed linux/interrupt.h from netdevice.h. This fixes below build failure drivers/net/pxa168_eth.c: In function 'pxa168_eth_collect_events': drivers/net/pxa168_eth.c:866: error: 'IRQ_NONE' undeclared (first use in this function) drivers/net/pxa168_eth.c:866: error: (Each undeclared identifier is reported only once drivers/net/pxa168_eth.c:866: error: for each function it appears in.) drivers/net/pxa168_eth.c: At top level: drivers/net/pxa168_eth.c:913: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'pxa168_eth_int_handler' drivers/net/pxa168_eth.c: In function 'pxa168_eth_open': drivers/net/pxa168_eth.c:1133: error: implicit declaration of function 'request_irq' drivers/net/pxa168_eth.c:1133: error: 'pxa168_eth_int_handler' undeclared (first use in this function) drivers/net/pxa168_eth.c:1134: error: 'IRQF_DISABLED' undeclared (first use in this function) drivers/net/pxa168_eth.c:1160: error: implicit declaration of function 'free_irq' Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20netconsole: switch init_netconsole() to late_initcallLin Ming1-1/+7
Commit 88491d8(drivers/net: Kconfig & Makefile cleanup) causes a regression that netconsole does not work if netconsole and network device driver are build into kernel, because netconsole is linked before network device driver. Andrew Morton suggested to fix this with initcall ordering. Fixes it by switching init_netconsole() to late_initcall. Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20gianfar: Fix overflow check and return value for gfar_get_cls_all()Ben Hutchings1-4/+4
This function may currently fill one entry beyond the end of the array it is given. It also doesn't return an error code in case it does detect overflow. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20ppp_generic: fix multilink fragment MTU calculation (again)Henry Wong1-1/+6
When using MLPPP, the maximum size of a fragment is incorrectly calculated with an offset of -2. This patch reverses the changes in the patch found here: http://marc.info/?l=linux-netdev&m=123541324010539&w=2 The value of hdrlen includes the size of both the 2-byte PPP protocol field and the 2- or 4-byte multilink header (2+4=6 for long sequence numbers, 2+2=4 for short sequence numbers). Section 2 of RFC1661 says that the MRU that is negotiated (i.e., the MTU of the sending system) includes only the PPP payload but not the protocol field, thus the correct MTU should be the link's MTU minus the multilink header (mtu - (hdrlen-2)). The incorrect calculation causes Linux to fragment packets to a size two bytes smaller than the allowed MTU. While not technically illegal, this behaviour confounds MRU-tuning to avoid PPP-layer fragmentation. Signed-off-by: Henry Wong <henry@stuffedcow.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20GRETH: avoid overwrite IP-stack's IP-frags checksumDaniel Hellstrom1-2/+5
The GRETH GBIT core does not do checksum offloading for IP segmentation. This patch adds a check in the xmit function to determine if the stack has calculated the checksum for us. Signed-off-by: Daniel Hellstrom <daniel@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20GRETH: RX/TX bytes were never increasedDaniel Hellstrom2-0/+6
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20ipv6: fix a possible double freeRoy Li1-2/+2
When calling snmp6_alloc_dev fails, the snmp6 relevant memory are freed by snmp6_alloc_dev. Calling in6_dev_finish_destroy will free these memory twice. Double free will lead that undefined behavior occurs. Signed-off-by: Roy Li <rongqing.li@windriver.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-20Merge branch 'btrfs-3.0' into for-linusChris Mason1-1/+6
2011-09-20Btrfs: reserve sufficient space for ioctl cloneSage Weil1-1/+6
Fix a crash/BUG_ON in the clone ioctl due to insufficient reservation. We need to reserve space for: - adjusting the old extent (possibly splitting it) - adding the new extent - updating the inode Signed-off-by: Sage Weil <sage@newdream.net> Signed-off-by: Chris Mason <chris.mason@oracle.com>
2011-09-20Merge branch 'davem.r8169.fixes' of git://violet.fr.zoreil.com/romieu/linuxDavid S. Miller1-5/+27
2011-09-20Merge git://git.samba.org/sfrench/cifs-2.6Linus Torvalds4-50/+21
* git://git.samba.org/sfrench/cifs-2.6: cifs: Fix broken sec=ntlmv2/i sec option (try #2) Fix the conflict between rwpidforward and rw mount options CIFS: Fix ERR_PTR dereference in cifs_get_root cifs: fix possible memory corruption in CIFSFindNext
2011-09-20Merge git://www.linux-watchdog.org/linux-watchdogLinus Torvalds4-16/+17
* git://www.linux-watchdog.org/linux-watchdog: watchdog: Initconst section fixes for watchdog watchdog: lantiq: fix watchdogs timeout handling watchdog: hpwdt: prevent multiple "NMI occurred" messages watchdog: WatchDog Timer Driver Core - use passed watchdog_device
2011-09-20Merge branch 'for-linus' of git://github.com/tiwai/soundLinus Torvalds2-4/+6
* 'for-linus' of git://github.com/tiwai/sound: ALSA: HDA: Add support for IDT 92HD93 ALSA: hda/realtek - Fix auto-mute with HP+LO configuration
2011-09-20Merge branch 'master' of ssh://infradead/~/public_git/wireless into for-davemJohn W. Linville10-59/+98
2011-09-20watchdog: Initconst section fixes for watchdogAndi Kleen1-1/+1
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2011-09-20watchdog: lantiq: fix watchdogs timeout handlingJohn Crispin1-4/+4
The enable function was using the global timeout variable for local operations. This resulted in the value of the global variable being corrupted, thus breaking the code. Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Thomas Langer <thomas.langer@lantiq.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: linux-watchdog@vger.kernel.org Cc: linux-mips@linux-mips.org
2011-09-20watchdog: hpwdt: prevent multiple "NMI occurred" messagesNaga Chumbalkar1-4/+5
On platforms with no iCRU support don't print two, (possibly conflicting), "NMI occurred" messages when the firmware is unable to source the NMI. Please note that one of the enhancements to the v1.3.0 hpwdt driver is to panic and allow KDUMP to succeed even on NMIs that are unknown to the platform firmware. Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com> Reviewed-by: Thomas Mingarelli <thomas.mingarelli@hp.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2011-09-20watchdog: WatchDog Timer Driver Core - use passed watchdog_deviceH Hartley Sweeten1-7/+7
Use the passed watchdog_device instead of the static global variable when testing and setting the status in watchdog_ping, watchdog_start, and watchdog_stop. Note that the callers of these functions are actually passing the static global variable. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2011-09-20ALSA: HDA: Add support for IDT 92HD93David Henningsson1-0/+1
Cc: stable@kernel.org BugLink: http://bugs.launchpad.net/bugs/854468 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-09-19cifs: Fix broken sec=ntlmv2/i sec option (try #2)Shirish Pargaonkar1-43/+11
Fix sec=ntlmv2/i authentication option during mount of Samba shares. cifs client was coding ntlmv2 response incorrectly. All that is needed in temp as specified in MS-NLMP seciton 3.3.2 "Define ComputeResponse(NegFlg, ResponseKeyNT, ResponseKeyLM, CHALLENGE_MESSAGE.ServerChallenge, ClientChallenge, Time, ServerName) as Set temp to ConcatenationOf(Responserversion, HiResponserversion, Z(6), Time, ClientChallenge, Z(4), ServerName, Z(4)" is MsvAvNbDomainName. For sec=ntlmsspi, build_av_pair is not used, a blob is plucked from type 2 response sent by the server to use in authentication. I tested sec=ntlmv2/i and sec=ntlmssp/i mount options against Samba (3.6) and Windows - XP, 2003 Server and 7. They all worked. Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
2011-09-19Fix the conflict between rwpidforward and rw mount optionsSteve French1-2/+2
Both these options are started with "rw" - that's why the first one isn't switched on even if it is specified. Fix this by adding a length check for "rw" option check. Cc: <stable@kernel.org> Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru> Signed-off-by: Steve French <sfrench@us.ibm.com>
2011-09-19CIFS: Fix ERR_PTR dereference in cifs_get_rootPavel Shilovsky1-4/+6
move it to the beginning of the loop. Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
2011-09-19cifs: fix possible memory corruption in CIFSFindNextJeff Layton1-1/+2
The name_len variable in CIFSFindNext is a signed int that gets set to the resume_name_len in the cifs_search_info. The resume_name_len however is unsigned and for some infolevels is populated directly from a 32 bit value sent by the server. If the server sends a very large value for this, then that value could look negative when converted to a signed int. That would make that value pass the PATH_MAX check later in CIFSFindNext. The name_len would then be used as a length value for a memcpy. It would then be treated as unsigned again, and the memcpy scribbles over a ton of memory. Fix this by making the name_len an unsigned value in CIFSFindNext. Cc: <stable@kernel.org> Reported-by: Darren Lavender <dcl@hppine99.gbr.hp.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
2011-09-19Merge branch 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tipLinus Torvalds2-2/+2
* 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip: x86, iommu: Mark DMAR IRQ as non-threaded genirq: Make irq_shutdown() symmetric vs. irq_startup again
2011-09-19Merge branch 'for-linus' of git://github.com/chrismason/linuxLinus Torvalds3-11/+30
* 'for-linus' of git://github.com/chrismason/linux: Btrfs: only clear the need lookup flag after the dentry is setup BTRFS: Fix lseek return value for error Btrfs: don't change inode flag of the dest clone file Btrfs: don't make a file partly checksummed through file clone Btrfs: fix pages truncation in btrfs_ioctl_clone() btrfs: fix d_off in the first dirent
2011-09-19USB: xHCI: prevent infinite loop when processing MSE eventAndiry Xu1-0/+19
When a xHC host is unable to handle isochronous transfer in the interval, it reports a Missed Service Error event and skips some tds. Currently xhci driver handles MSE event in the following ways: 1. When encounter a MSE event, set ep->skip flag, update event ring dequeue pointer and return. 2. When encounter the next event on this ep, the driver will run the do-while loop, fetch td from ep's td_list to find the td corresponding to this event. All tds missed are marked as short transfer(-EXDEV). The do-while loop will end in two ways: 1. If the td pointed by the event trb is found; 2. If the ep ring's td_list is empty. However, if a buggy HW reports some unpredicted event (for example, an overrun event following a MSE event while the ep ring is actually not empty), the driver will never find the td, and it will loop until the td_list is empty. Unfortunately, the spinlock is dropped when give back a urb in the do-while loop. During the spinlock released period, the class driver may still submit urbs and add tds to the td_list. This may cause disaster, since the td_list will never be empty and the loop never ends, and the system hangs. To fix this, count the number of TDs on the ep ring before skipping TDs, and quit the loop when skipped that number of tds. This guarantees the do-while loop will end after certain number of cycles, and driver will not be trapped in an infinite loop. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-19USB: xhci: Set change bit when warm reset change is set.Greg KH1-1/+1
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther Point xHCI host controller will report a link state change with the state set to "SS.Inactive". This causes the xHCI host controller to issue a warm port reset, which doesn't finish before the USB core times out while waiting for it to complete. When the warm port reset does complete, and the xHC gives back a port status change event, the xHCI driver kicks khubd. However, it fails to set the bit indicating there is a change event for that port because the logic in xhci-hub.c doesn't check for the warm port reset bit. After that, the warm port status change bit is never cleared by the USB core, and the xHC stops reporting port status change bits. (The xHCI spec says it shouldn't report more port events until all change bits are cleared.) This means any port changes when a new device is connected will never be reported, and the port will seem "dead" until the xHCI driver is unloaded and reloaded, or the computer is rebooted. Fix this by making the xHCI driver set the port change bit when a warm port reset change bit is set. A better solution would be to make the USB core handle warm port reset in differently, merging the current code with the standard port reset code that does an incremental backoff on the timeout, and tries to complete the port reset two more times before giving up. That more complicated fix will be merged next window, and this fix will be backported to stable. This should be backported to kernels as old as 3.0, since that was the first kernel with commit a11496ebf375 ("xHCI: warm reset support"). Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-19staging: fix comedi build when ISA_DMA_API is enabled but COMEDI_PCI is not ↵Randy Dunlap1-1/+3
enabled Fix build when CONFIG_ISA_DMA_API is enabled but CONFIG_COMEDI_PCI[_DRIVERS] is not enabled. Fixes these build errors: drivers/staging/comedi/drivers/ni_labpc.c: In function 'labpc_ai_cmd': drivers/staging/comedi/drivers/ni_labpc.c:1351: error: implicit declaration of function 'labpc_suggest_transfer_size' drivers/staging/comedi/drivers/ni_labpc.c: At top level: drivers/staging/comedi/drivers/ni_labpc.c:1802: error: conflicting types for 'labpc_suggest_transfer_size' drivers/staging/comedi/drivers/ni_labpc.c:1351: note: previous implicit declaration of 'labpc_suggest_transfer_size' was here Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-19Make taskstats round statistics down to nearest 1k bytes/eventsLinus Torvalds1-7/+8
Even with just the interface limited to admin, there really is little to reason to give byte-per-byte counts for taskstats. So round it down to something less intrusive. Acked-by: Balbir Singh <bsingharora@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-19Make TASKSTATS require root accessLinus Torvalds1-0/+1
Ok, this isn't optimal, since it means that 'iotop' needs admin capabilities, and we may have to work on this some more. But at the same time it is very much not acceptable to let anybody just read anybody elses IO statistics quite at this level. Use of the GENL_ADMIN_PERM suggested by Johannes Berg as an alternative to checking the capabilities by hand. Reported-by: Vasiliy Kulikov <segoon@openwall.com> Cc: Johannes Berg <johannes.berg@intel.com> Acked-by: Balbir Singh <bsingharora@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-19b43: Fix beacon problem in ad-hoc modeManual Munz1-1/+2
In ad-hoc mode, driver b43 does not issue beacons. Signed-off-by: Manual Munz <freifunk@somakoma.de> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-26 08:25:31 +0000