path: root/man/en_US/ifconfig.8

.TH IFCONFIG 8 "2003-02-08" "net-tools" "Linux Programmer's Manual"
.SH NAME
ifconfig \- configure a network interface
.SH SYNOPSIS
.B "ifconfig [-v] [-a] [-s] [interface]"
.br
.B "ifconfig [-v] interface [aftype] options | address ..."
.SH DESCRIPTION
.B Ifconfig
is used to configure the kernel-resident network interfaces.  It is
used at boot time to set up interfaces as necessary.  After that, it
is usually only needed when debugging or when system tuning is needed.
.LP
If no arguments are given,
.B ifconfig
displays the status of the currently active interfaces.  If
a single
.B interface
argument is given, it displays the status of the given interface
only; if a single
.B -a
argument is given, it displays the status of all interfaces, even
those that are down.  Otherwise, it configures an interface.

.SH Address Families
If the first argument after the interface name is recognized as
the name of a supported address family, that address family is
used for decoding and displaying all protocol addresses.  Currently
supported address families include
.B inet
(TCP/IP, default), 
.B inet6
(IPv6),
.B ax25
(AMPR Packet Radio),
.B ddp
(Appletalk Phase 2),
.B ipx
(Novell IPX) and
.B netrom
(AMPR Packet radio).
.SH OPTIONS
.TP
.B -a
display all interfaces which are currently available, even if down
.TP
.B -s
display a short list (like netstat -i)
.TP
.B -v
be more verbose for some error conditions
.TP
.B interface
The name of the interface.  This is usually a driver name followed by
a unit number, for example
.B eth0
for the first Ethernet interface. If your kernel supports alias interfaces,
you can specify them with 
.B eth0:0
for the first alias of eth0. You can use them to assign a second address. To
delete an alias interface use
.B ifconfig eth0:0 down
. Note: for every scope (i.e. same net with address/netmask combination) all
aliases are deleted, if you delete the first (primary).
.TP
.B up
This flag causes the interface to be activated.  It is implicitly
specified if an address is assigned to the interface.
.TP
.B down
This flag causes the driver for this interface to be shut down.
.TP
.B "[\-]arp"
Enable or disable the use of the ARP protocol on this interface.
.TP
.B "[\-]promisc"
Enable or disable the
.B promiscuous
mode of the interface.  If selected, all packets on the network will
be received by the interface.
.TP
.B "[\-]allmulti"
Enable or disable 
.B all-multicast
mode.  If selected, all multicast packets on the network will be
received by the interface.
.TP
.B "metric N"
This parameter sets the interface metric.
.TP
.B "mtu N"
This parameter sets the Maximum Transfer Unit (MTU) of an interface.
.TP
.B "dstaddr addr"
Set the remote IP address for a point-to-point link (such as
PPP).  This keyword is now obsolete; use the
.B pointopoint
keyword instead.
.TP
.B "netmask addr"
Set the IP network mask for this interface.  This value defaults to the
usual class A, B or C network mask (as derived from the interface IP
address), but it can be set to any value.
.TP
.B "add addr/prefixlen"
Add an IPv6 address to an interface. 
.TP
.B "del addr/prefixlen"
Remove an IPv6 address from an interface.
.TP
.B "tunnel aa.bb.cc.dd"
Create a new SIT (IPv6-in-IPv4) device, tunnelling to the given destination.
.TP
.B "irq addr"
Set the interrupt line used by this device.  Not all devices can
dynamically change their IRQ setting.
.TP
.B "io_addr addr"
Set the start address in I/O space for this device. 
.TP
.B "mem_start addr"
Set the start address for shared memory used by this device.  Only a
few devices need this.
.TP
.B "media type"
Set the physical port or medium type to be used by the device.  Not
all devices can change this setting, and those that can vary in what
values they support.  Typical values for
.B type
are 
.B 10base2
(thin Ethernet),
.B 10baseT
(twisted-pair 10Mbps Ethernet),
.B AUI 
(external transceiver) and so on.  The special medium type of
.B auto
can be used to tell the driver to auto-sense the media.  Again, not
all drivers can do this.
.TP
.B "[-]broadcast [addr]"
If the address argument is given, set the protocol broadcast
address for this interface.  Otherwise, set (or clear) the
.B IFF_BROADCAST
flag for the interface.
.TP
.B "[-]pointopoint [addr]"
This keyword enables the
.B point-to-point
mode of an interface, meaning that it is a direct link between two
machines with nobody else listening on it.
.br
If the address argument is also given, set the protocol address of
the other side of the link, just like the obsolete
.B dstaddr
keyword does.  Otherwise, set or clear the
.B IFF_POINTOPOINT
flag for the interface. 
.TP
.B hw class address
Set the hardware address of this interface, if the device driver
supports this operation.  The keyword must be followed by the
name of the hardware class and the printable ASCII equivalent of
the hardware address.  Hardware classes currently supported include
.B ether
(Ethernet),
.B ax25
(AMPR AX.25),
.B ARCnet
and
.B netrom
(AMPR NET/ROM).
.TP
.B multicast
Set the multicast flag on the interface. This should not normally be needed
as the drivers set the flag correctly themselves.
.TP
.B address
The IP address to be assigned to this interface.
.TP
.B txqueuelen length
Set the length of the transmit queue of the device. It is useful to set this
to small values for slower devices with a high latency (modem links, ISDN)
to prevent fast bulk transfers from disturbing interactive traffic like
telnet too much. 
.SH NOTES
Since kernel release 2.2 there are no explicit interface statistics for
alias interfaces anymore. The statistics printed for the original address
are shared with all alias addresses on the same device. If you want per-address
statistics you should add explicit accounting
rules for the address using the 
.BR ipchains(8)
command.
.LP
Since net-tools 1.61 ifconfig is printing byte counters with SI units. So
1 KiB are 2^10 byte. Note, the numbers are truncated to one decimal (which can
by quite a large error if you consider 0.1 PiB is 112.589.990.684.262
bytes :)
.LP
Interrupt problems with Ethernet device drivers fail with EAGAIN
.I (SIOCSIIFLAGS: Resource temporarily unavailable)
it is most likely a interrupt conflict. See
.I http://www.scyld.com/expert/irq-conflict.html
for more information.
.SH FILES
.I /proc/net/socket 
.br
.I /proc/net/dev
.br
.I /proc/net/if_inet6
.SH BUGS
While appletalk DDP and IPX addresses will be displayed they cannot be
altered by this command.
.SH SEE ALSO
route(8), netstat(8), arp(8), rarp(8), ipchains(8)
.br
http://physics.nist.gov/cuu/Units/binary.html - Prefixes for binary multiples
.SH AUTHORS
Fred N. van Kempen, <waltje@uwalt.nl.mugnet.org>
.br
Alan Cox, <Alan.Cox@linux.org>
.br
Phil Blundell, <Philip.Blundell@pobox.com>
.br
Andi Kleen; 
.br
Bernd Eckenfels, <net-tools@lina.inka.de>