Spec: Add eth0 device as NetworkInterfaceBlacklist in ivi profile.

In order to communicate with Cluster device, this patch set eth0 as
NetworkInterfaceBlacklist member in connman configuration. This patch is
only applied for ivi profile.

Change-Id: If340dda5702973b470a78375370bc43180b2b53a
Signed-off-by: Sangjung Woo <sangjung.woo@samsung.com>

1 files changed, 110 insertions, 0 deletions

diff --git a/src/main_ivi.conf b/src/main_ivi.conf
new file mode 100755
index 00000000..627bd061
--- /dev/null
+++ b/src/main_ivi.conf
@@ -0,0 +1,110 @@
+[General]
+
+# Set input request timeout. Default is 120 seconds
+# The request for inputs like passphrase will timeout
+# after certain amount of time. Use this setting to
+# increase the value in case of different user
+# interface designs.
+# InputRequestTimeout = 120
+
+# Set browser launch timeout. Default is 300 seconds
+# The request for launching a browser for portal pages
+# will timeout after certain amount of time. Use this
+# setting to increase the value in case of different
+# user interface designs.
+# BrowserLaunchTimeout = 300
+
+# Enable background scanning. Default is true.
+# Background scanning will start every 5 minutes unless
+# the scan list is empty. In that case, a simple backoff
+# mechanism starting from 10s up to 5 minutes will run.
+# BackgroundScanning = true
+BackgroundScanning = false
+
+# List of Fallback timeservers separated by ",".
+# These timeservers are used for NTP sync when there are
+# no timeserver set by the user or by the service.
+# These can contain mixed combination of fully qualified
+# domain names, IPv4 and IPv6 addresses.
+# FallbackTimeservers =
+#FallbackTimeservers = pool.ntp.org
+
+# List of fallback nameservers separated by "," used if no
+# nameservers are otherwise provided by the service. The
+# nameserver entries must be in numeric format, host
+# names are ignored.
+# FallbackNameservers =
+
+# List of technologies that are marked autoconnectable
+# by default, separated by commas ",". The default value
+# for this entry when empty is ethernet,wifi,cellular.
+# Services that are automatically connected must have been
+# set up and saved to storage beforehand.
+# DefaultAutoConnectTechnologies =
+
+# List of preferred technologies from the most preferred
+# one to the least preferred one separated by commas ",".
+# Services of the listed technology type will be tried one
+# by one in the order given, until one of them gets connected
+# or they are all tried. A service of a preferred technology
+# type in state 'ready' will get the default route when
+# compared to another preferred type further down the list
+# with state 'ready' or with a non-preferred type; a service
+# of a preferred technology type in state 'online' will get
+# the default route when compared to either a non-preferred
+# type or a preferred type further down in the list.
+# PreferredTechnologies =
+PreferredTechnologies = wifi, ethernet
+
+# List of blacklisted network interfaces separated by ",".
+# Found interfaces will be compared to the list and will
+# not be handled by connman, if their first characters
+# match any of the list entries. Default value is
+# vmnet,vboxnet,virbr,ifb.
+# NetworkInterfaceBlacklist = vmnet,vboxnet,virbr,ifb
+NetworkInterfaceBlacklist = veth, vmnet,vboxnet,virbr,usb,rndis,rmnet,rev_rmnet,dummy,seth_td,seth_w,eth0
+
+# Allow connman to change the system hostname. This can
+# happen for example if we receive DHCP hostname option.
+# Default value is true.
+# AllowHostnameUpdates = true
+
+# Keep only a single connected technology at any time. When a new
+# service is connected by the user or a better one is found according
+# to PreferredTechnologies, the new service is kept connected and all
+# the other previously connected services are disconnected. With this
+# setting it does not matter whether the previously connected services
+# are in 'online' or 'ready' states, the newly connected service is
+# the only one that will be kept connected. A service connected by the
+# user will be used until going out of network coverage. With this
+# setting enabled applications will notice more network breaks than
+# normal. Default value is false.
+# SingleConnectedTechnology = false
+SingleConnectedTechnology = true
+
+# List of technologies for which tethering is allowed separated by ",".
+# The default value is wifi,bluetooth,gadget. Only those technologies
+# listed here are used for tethering. If ethernet tethering is desired,
+# then ethernet should be added to the list. The technologies listed here
+# have to support tethering, currently tethering is implemented for wifi,
+# bluetooth, gadget and ethernet.
+# NOTE that if ethernet tethering is enabled, then a DHCP server is
+# started on all ethernet interfaces. Tethered ethernet should
+# never be connected to corporate or home network as it will disrupt
+# normal operation of these networks. Due to this ethernet is not
+# tethered by default. Do not activate ethernet tethering unless you
+# really know what you are doing.
+# TetheringTechnologies = wifi,bluetooth,gadget
+
+# Restore earlier tethering status when returning from offline mode,
+# re-enabling a technology, and after restarts and reboots.
+# Default value is false.
+# PersistentTetheringMode = false
+
+# Automatically enable Anycast 6to4 if possible. This is not recommended, as
+# the use of 6to4 will generally lead to a severe degradation of connection
+# quality. See RFC6343. Default value is false (as recommended by RFC6343
+# section 4.1).
+# Enable6to4 = false
+
+NetworkCellularInterfaceList = pdp,rmnet,seth_td,seth_w