Merge "Spec: Add eth0 device as NetworkInterfaceBlacklist in ivi profile." into tizensubmit/tizen_3.0_common/20161104.104000submit/tizen_3.0/20161028.092423submit/tizen_3.0/20161028.062323submit/tizen/20161011.075122accepted/tizen/wearable/20161011.234313accepted/tizen/tv/20161011.234258accepted/tizen/mobile/20161011.234412accepted/tizen/ivi/20161011.234346accepted/tizen/common/20161011.154420accepted/tizen/3.0/wearable/20161028.150857accepted/tizen/3.0/tv/20161028.143553accepted/tizen/3.0/mobile/20161028.143243accepted/tizen/3.0/ivi/20161028.151403

1 files changed, 110 insertions, 0 deletions

diff --git a/src/main_ivi.conf b/src/main_ivi.conf
new file mode 100755
index 00000000..627bd061
--- /dev/null
+++ b/src/main_ivi.conf
@@ -0,0 +1,110 @@
+[General]
+
+# Set input request timeout. Default is 120 seconds
+# The request for inputs like passphrase will timeout
+# after certain amount of time. Use this setting to
+# increase the value in case of different user
+# interface designs.
+# InputRequestTimeout = 120
+
+# Set browser launch timeout. Default is 300 seconds
+# The request for launching a browser for portal pages
+# will timeout after certain amount of time. Use this
+# setting to increase the value in case of different
+# user interface designs.
+# BrowserLaunchTimeout = 300
+
+# Enable background scanning. Default is true.
+# Background scanning will start every 5 minutes unless
+# the scan list is empty. In that case, a simple backoff
+# mechanism starting from 10s up to 5 minutes will run.
+# BackgroundScanning = true
+BackgroundScanning = false
+
+# List of Fallback timeservers separated by ",".
+# These timeservers are used for NTP sync when there are
+# no timeserver set by the user or by the service.
+# These can contain mixed combination of fully qualified
+# domain names, IPv4 and IPv6 addresses.
+# FallbackTimeservers =
+#FallbackTimeservers = pool.ntp.org
+
+# List of fallback nameservers separated by "," used if no
+# nameservers are otherwise provided by the service. The
+# nameserver entries must be in numeric format, host
+# names are ignored.
+# FallbackNameservers =
+
+# List of technologies that are marked autoconnectable
+# by default, separated by commas ",". The default value
+# for this entry when empty is ethernet,wifi,cellular.
+# Services that are automatically connected must have been
+# set up and saved to storage beforehand.
+# DefaultAutoConnectTechnologies =
+
+# List of preferred technologies from the most preferred
+# one to the least preferred one separated by commas ",".
+# Services of the listed technology type will be tried one
+# by one in the order given, until one of them gets connected
+# or they are all tried. A service of a preferred technology
+# type in state 'ready' will get the default route when
+# compared to another preferred type further down the list
+# with state 'ready' or with a non-preferred type; a service
+# of a preferred technology type in state 'online' will get
+# the default route when compared to either a non-preferred
+# type or a preferred type further down in the list.
+# PreferredTechnologies =
+PreferredTechnologies = wifi, ethernet
+
+# List of blacklisted network interfaces separated by ",".
+# Found interfaces will be compared to the list and will
+# not be handled by connman, if their first characters
+# match any of the list entries. Default value is
+# vmnet,vboxnet,virbr,ifb.
+# NetworkInterfaceBlacklist = vmnet,vboxnet,virbr,ifb
+NetworkInterfaceBlacklist = veth, vmnet,vboxnet,virbr,usb,rndis,rmnet,rev_rmnet,dummy,seth_td,seth_w,eth0
+
+# Allow connman to change the system hostname. This can
+# happen for example if we receive DHCP hostname option.
+# Default value is true.
+# AllowHostnameUpdates = true
+
+# Keep only a single connected technology at any time. When a new
+# service is connected by the user or a better one is found according
+# to PreferredTechnologies, the new service is kept connected and all
+# the other previously connected services are disconnected. With this
+# setting it does not matter whether the previously connected services
+# are in 'online' or 'ready' states, the newly connected service is
+# the only one that will be kept connected. A service connected by the
+# user will be used until going out of network coverage. With this
+# setting enabled applications will notice more network breaks than
+# normal. Default value is false.
+# SingleConnectedTechnology = false
+SingleConnectedTechnology = true
+
+# List of technologies for which tethering is allowed separated by ",".
+# The default value is wifi,bluetooth,gadget. Only those technologies
+# listed here are used for tethering. If ethernet tethering is desired,
+# then ethernet should be added to the list. The technologies listed here
+# have to support tethering, currently tethering is implemented for wifi,
+# bluetooth, gadget and ethernet.
+# NOTE that if ethernet tethering is enabled, then a DHCP server is
+# started on all ethernet interfaces. Tethered ethernet should
+# never be connected to corporate or home network as it will disrupt
+# normal operation of these networks. Due to this ethernet is not
+# tethered by default. Do not activate ethernet tethering unless you
+# really know what you are doing.
+# TetheringTechnologies = wifi,bluetooth,gadget
+
+# Restore earlier tethering status when returning from offline mode,
+# re-enabling a technology, and after restarts and reboots.
+# Default value is false.
+# PersistentTetheringMode = false
+
+# Automatically enable Anycast 6to4 if possible. This is not recommended, as
+# the use of 6to4 will generally lead to a severe degradation of connection
+# quality. See RFC6343. Default value is false (as recommended by RFC6343
+# section 4.1).
+# Enable6to4 = false
+
+NetworkCellularInterfaceList = pdp,rmnet,seth_td,seth_w