1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
|
/*
* Internal Definitions
*/
#define BOOTFLASH_START 0xF0000000
/*
* DDR Setup
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
#define CFG_83XX_DDR_USES_CS0
/*
* Manually set up DDR parameters
*/
#define CONFIG_DDR_II
#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
/*
* The reserved memory
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_SYS_FLASH_BASE 0xF0000000
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#endif
/* Reserve 768 kB for Mon */
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
/*
* Initial RAM Base Address Setup
*/
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
/*
* Init Local Bus Memory Controller:
*
* Bank Bus Machine PortSz Size Device
* ---- --- ------- ------ ----- ------
* 0 Local GPCM 16 bit 256MB FLASH
* 1 Local GPCM 8 bit 128MB GPIO/PIGGY
*
*/
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
/*
* Serial Port
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_NUM_I2C_BUSES 4
#define CONFIG_SYS_I2C_MAX_HOPS 1
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 200000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C_OFFSET 0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED 200000
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
{1, {I2C_NULL_HOP} } }
#if defined(CONFIG_CMD_NAND)
#define CONFIG_NAND_KMETER1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
#endif
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
/*
* Environment
*/
#ifndef CONFIG_SYS_RAMBOOT
/* Address and size of Redundant Environment Sector */
#endif /* CFG_SYS_RAMBOOT */
/*
* Environment Configuration
*/
#define CONFIG_ENV_OVERWRITE
#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
#define CONFIG_KM_DEF_ENV "km-common=empty\0"
#endif
#ifndef CONFIG_KM_DEF_ARCH
#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_KM_DEF_ENV \
CONFIG_KM_DEF_ARCH \
"newenv=" \
"prot off " __stringify(CONFIG_ENV_ADDR) " +0x40000 && " \
"era " __stringify(CONFIG_ENV_ADDR) " +0x40000\0" \
"unlock=yes\0" \
""
#if defined(CONFIG_UEC_ETH)
#define CONFIG_HAS_ETH0
#endif
/*
* QE UEC ethernet configuration
*/
#define CONFIG_UEC_ETH
#define CONFIG_ETHPRIME "UEC0"
|
