1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net>
*
* Based on original Kirkwood support which is
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
*/
#ifndef _CONFIG_EDMINIV2_H
#define _CONFIG_EDMINIV2_H
/*
* SPL
*/
#define CONFIG_SPL_STACK 0x00020000
#define CONFIG_SPL_BSS_START_ADDR 0x00020000
#define CONFIG_SYS_SPL_MALLOC_START 0x00040000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x0001ffff
#define CONFIG_SYS_UBOOT_BASE 0xfff90000
#define CONFIG_SYS_UBOOT_START 0x00800000
/*
* High Level Configuration Options (easy to change)
*/
#include <asm/arch/orion5x.h>
/*
* CLKs configurations
*/
/*
* Board-specific values for Orion5x MPP low level init:
* - MPPs 12 to 15 are SATA LEDs (mode 5)
* - Others are GPIO/unused (mode 3 for MPP0, mode 5 for
* MPP16 to MPP19, mode 0 for others
*/
#define ORION5X_MPP0_7 0x00000003
#define ORION5X_MPP8_15 0x55550000
#define ORION5X_MPP16_23 0x00005555
/*
* Board-specific values for Orion5x GPIO low level init:
* - GPIO3 is input (RTC interrupt)
* - GPIO16 is Power LED control (0 = on, 1 = off)
* - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16)
* - GPIO18 is Power Button status (0 = Released, 1 = Pressed)
* - GPIO19 is SATA disk power toggle (toggles on 0-to-1)
* - GPIO22 is SATA disk power status ()
* - GPIO23 is supply status for SATA disk ()
* - GPIO24 is supply control for board (write 1 to power off)
* Last GPIO is 25, further bits are supposed to be 0.
* Enable mask has ones for INPUT, 0 for OUTPUT.
* Default is LED ON, board ON :)
*/
#define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca
#define ORION5X_GPIO_OUT_VALUE 0x00000000
#define ORION5X_GPIO_IN_POLARITY 0x000000d0
/*
* NS16550 Configuration
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
#define CONFIG_SYS_NS16550_COM1 ORION5X_UART0_BASE
/*
* Serial Port configuration
* The following definitions let you select what serial you want to use
* for your console driver.
*/
#define CONFIG_SYS_BAUDRATE_TABLE \
{ 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 }
/*
* FLASH configuration
*/
#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max num of sects on one chip */
#define CONFIG_SYS_FLASH_BASE 0xfff80000
/* auto boot */
/*
* Network
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */
#define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */
#define CONFIG_PHY_BASE_ADR 0x8
#endif
/*
* IDE
*/
#ifdef CONFIG_IDE
#define __io
/* Data, registers and alternate blocks are at the same offset */
/* Each 8-bit ATA register is aligned to a 4-bytes address */
/* Controller supports 48-bits LBA addressing */
#define CONFIG_LBA48
/* A single bus, a single device */
/* ATA registers base is at SATA controller base */
/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
/* end of IDE defines */
#endif /* CMD_IDE */
/*
* Common USB/EHCI configuration
*/
#ifdef CONFIG_CMD_USB
#define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE
#endif /* CONFIG_CMD_USB */
/*
* I2C related stuff
*/
#ifdef CONFIG_CMD_I2C
#define CONFIG_I2C_MVTWSI_BASE0 ORION5X_TWSI_BASE
#endif
/*
* Environment variables configurations
*/
/* Enable command line editing */
/* provide extensive help */
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0
#endif /* _CONFIG_EDMINIV2_H */
|
