1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
|
# SPDX-License-Identifier: GPL-2.0+
#
# Xilinx ZYNQ U-Boot
#
# (C) Copyright 2013 Xilinx, Inc.
1. About this
This document describes the information about Xilinx Zynq U-Boot -
like supported boards, ML status and TODO list.
2. Zynq boards
Xilinx Zynq-7000 All Programmable SoCs enable extensive system level
differentiation, integration, and flexibility through hardware, software,
and I/O programmability.
* zc702 (single qspi, gem0, mmc) [1]
* zc706 (dual parallel qspi, gem0, mmc) [2]
* zed (single qspi, gem0, mmc) [3]
* microzed (single qspi, gem0, mmc) [4]
* zc770
- zc770-xm010 (single qspi, gem0, mmc)
- zc770-xm011 (8 or 16 bit nand)
- zc770-xm012 (nor)
- zc770-xm013 (dual parallel qspi, gem1)
3. Building
ex. configure and build for zc702 board
$ make zynq_zc702_config
$ make
4. Bootmode
Zynq has a facility to read the bootmode from the slcr bootmode register
once user is setting through jumpers on the board - see page no:1546 on [5]
All possible bootmode values are defined in Table 6-2:Boot_Mode MIO Pins
on [5].
board_late_init() will read the bootmode values using slcr bootmode register
at runtime and assign the modeboot variable to specific bootmode string which
is intern used in autoboot.
SLCR bootmode register Bit[3:0] values
#define ZYNQ_BM_NOR 0x02
#define ZYNQ_BM_SD 0x05
#define ZYNQ_BM_JTAG 0x0
"modeboot" variable can assign any of "norboot", "sdboot" or "jtagboot"
bootmode strings at runtime.
5. Mainline status
- Added basic board configurations support.
- Added zynq u-boot bsp code - arch/arm/cpu/armv7/zynq
- Added zynq boards named - zc70x, zed, microzed, zc770_xm010/xm011/xm012/xm013
- Added zynq drivers:
serial - drivers/serial/serial_zynq.c
net - drivers/net/zynq_gem.c
mmc - drivers/mmc/zynq_sdhci.c
spi - drivers/spi/zynq_spi.c
qspi - drivers/spi/zynq_qspi.c
i2c - drivers/i2c/zynq_i2c.c
nand - drivers/mtd/nand/raw/zynq_nand.c
- Done proper cleanups on board configurations
- Added basic FDT support for zynq boards
- d-cache support for zynq_gem.c
6. TODO
- Add FDT support on individual drivers
[1] http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htm
[2] http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htm
[3] http://zedboard.org/product/zedboard
[4] http://zedboard.org/product/microzed
[5] http://www.xilinx.com/support/documentation/user_guides/ug585-Zynq-7000-TRM.pdf
--
Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Sun Dec 15 14:52:41 IST 2013
|
