1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
|
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* Achim Ehrlich <aehrlich@taskit.de>
* taskit GmbH <www.taskit.de>
*
* (C) Copyright 2012-
* Markus Hubig <mhubig@imko.de>
* IMKO GmbH <www.imko.de>
* (C) Copyright 2014
* Heiko Schocher <hs@denx.de>
* DENX Software Engineering GmbH
*/
#include <common.h>
#include <dm.h>
#include <init.h>
#include <net.h>
#include <asm/io.h>
#include <asm/arch/at91sam9_sdramc.h>
#include <asm/arch/at91sam9260_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/atmel_serial.h>
#include <asm/arch/at91_spi.h>
#include <spi.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
#include <asm/gpio.h>
#include <watchdog.h>
# include <net.h>
#ifndef CONFIG_DM_ETH
# include <netdev.h>
#endif
#include <g_dnl.h>
DECLARE_GLOBAL_DATA_PTR;
static void smartweb_request_gpio(void)
{
gpio_request(CONFIG_SYS_NAND_ENABLE_PIN, "nand ena");
gpio_request(CONFIG_SYS_NAND_READY_PIN, "nand rdy");
gpio_request(AT91_PIN_PA26, "ena PHY");
}
static void smartweb_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
unsigned long csa;
/* Assign CS3 to NAND/SmartMedia Interface */
csa = readl(&matrix->ebicsa);
csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_TDF_CYCLE(2),
&smc->cs[3].mode);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
static void smartweb_macb_hw_init(void)
{
struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
/* Enable the PHY Chip via PA26 on the Stamp 2 Adaptor */
at91_set_gpio_output(AT91_PIN_PA26, 0);
/*
* Disable pull-up on:
* RXDV (PA17) => PHY normal mode (not Test mode)
* ERX0 (PA14) => PHY ADDR0
* ERX1 (PA15) => PHY ADDR1
* ERX2 (PA25) => PHY ADDR2
* ERX3 (PA26) => PHY ADDR3
* ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0
*
* PHY has internal pull-down
*/
writel(pin_to_mask(AT91_PIN_PA14) |
pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA17) |
pin_to_mask(AT91_PIN_PA25) |
pin_to_mask(AT91_PIN_PA26) |
pin_to_mask(AT91_PIN_PA28) |
pin_to_mask(AT91_PIN_PA29),
&pioa->pudr);
at91_phy_reset();
/* Re-enable pull-up */
writel(pin_to_mask(AT91_PIN_PA14) |
pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA17) |
pin_to_mask(AT91_PIN_PA25) |
pin_to_mask(AT91_PIN_PA26) |
pin_to_mask(AT91_PIN_PA28) |
pin_to_mask(AT91_PIN_PA29),
&pioa->puer);
/* Initialize EMAC=MACB hardware */
at91_macb_hw_init();
}
#ifdef CONFIG_USB_GADGET_AT91
#include <linux/usb/at91_udc.h>
void at91_udp_hw_init(void)
{
/* Enable PLLB */
at91_pllb_clk_enable(get_pllb_init());
/* Enable UDPCK clock, MCK is enabled in at91_clock_init() */
at91_periph_clk_enable(ATMEL_ID_UDP);
at91_system_clk_enable(AT91SAM926x_PMC_UDP);
}
struct at91_udc_data board_udc_data = {
.baseaddr = ATMEL_BASE_UDP0,
};
#endif
int board_early_init_f(void)
{
/* enable this here, as we have SPL without serial support */
at91_seriald_hw_init();
smartweb_request_gpio();
return 0;
}
int board_init(void)
{
smartweb_request_gpio();
/* power LED red */
at91_set_gpio_output(AT91_PIN_PC6, 0);
at91_set_gpio_output(AT91_PIN_PC7, 1);
/* alarm LED off */
at91_set_gpio_output(AT91_PIN_PC8, 0);
at91_set_gpio_output(AT91_PIN_PC9, 0);
/* prog LED red */
at91_set_gpio_output(AT91_PIN_PC10, 0);
at91_set_gpio_output(AT91_PIN_PC11, 1);
#ifdef CONFIG_USB_GADGET_AT91
at91_udp_hw_init();
at91_udc_probe(&board_udc_data);
#endif
/* Adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
smartweb_nand_hw_init();
smartweb_macb_hw_init();
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size(
(void *)CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
#ifndef CONFIG_DM_ETH
#ifdef CONFIG_MACB
int board_eth_init(struct bd_info *bis)
{
return macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00);
}
#endif /* CONFIG_MACB */
#endif
#if defined(CONFIG_SPL_BUILD)
#include <spl.h>
#include <nand.h>
#include <spi_flash.h>
void matrix_init(void)
{
struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX;
writel((readl(&mat->scfg[3]) & (~AT91_MATRIX_SLOT_CYCLE))
| AT91_MATRIX_SLOT_CYCLE_(0x40),
&mat->scfg[3]);
}
void at91_spl_board_init(void)
{
smartweb_request_gpio();
/* power LED orange */
at91_set_gpio_output(AT91_PIN_PC6, 1);
at91_set_gpio_output(AT91_PIN_PC7, 1);
/* alarm LED orange */
at91_set_gpio_output(AT91_PIN_PC8, 1);
at91_set_gpio_output(AT91_PIN_PC9, 1);
/* prog LED red */
at91_set_gpio_output(AT91_PIN_PC10, 0);
at91_set_gpio_output(AT91_PIN_PC11, 1);
smartweb_nand_hw_init();
at91_set_gpio_input(AT91_PIN_PA28, 1);
at91_set_gpio_input(AT91_PIN_PA29, 1);
/* check if both button are pressed */
if (at91_get_gpio_value(AT91_PIN_PA28) == 0 &&
at91_get_gpio_value(AT91_PIN_PA29) == 0) {
smartweb_nand_hw_init();
nand_init();
spl_nand_erase_one(0, 0);
}
}
#define SDRAM_BASE_CONF (AT91_SDRAMC_NC_9 | AT91_SDRAMC_NR_13 \
| AT91_SDRAMC_CAS_2 \
| AT91_SDRAMC_NB_4 | AT91_SDRAMC_DBW_32 \
| AT91_SDRAMC_TWR_VAL(2) | AT91_SDRAMC_TRC_VAL(7) \
| AT91_SDRAMC_TRP_VAL(2) | AT91_SDRAMC_TRCD_VAL(2) \
| AT91_SDRAMC_TRAS_VAL(5) | AT91_SDRAMC_TXSR_VAL(8))
void mem_init(void)
{
struct at91_matrix *ma = (struct at91_matrix *)ATMEL_BASE_MATRIX;
struct at91_port *port = (struct at91_port *)ATMEL_BASE_PIOC;
struct sdramc_reg setting;
setting.cr = SDRAM_BASE_CONF;
setting.mdr = AT91_SDRAMC_MD_SDRAM;
setting.tr = (CONFIG_SYS_MASTER_CLOCK * 7) / 1000000;
/*
* I write here directly in this register, because this
* approach is smaller than calling at91_set_a_periph() in a
* for loop. This saved me 96 bytes.
*/
writel(0xffff0000, &port->pdr);
writel(readl(&ma->ebicsa) | AT91_MATRIX_CS1A_SDRAMC, &ma->ebicsa);
sdramc_initialize(ATMEL_BASE_CS1, &setting);
}
#endif
int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char *name)
{
g_dnl_set_serialnumber("1");
return 0;
}
|
