// SPDX-License-Identifier: GPL-2.0+ /* * (C) Copyright 2009 SAMSUNG Electronics * Minkyu Kang * Jaehoon Chung * Portions Copyright 2011-2019 NVIDIA Corporation */ #include #include #include #include #include #include #include #include #include #include #include #if defined(CONFIG_TEGRA30) || defined(CONFIG_TEGRA210) #include #endif struct tegra_mmc_plat { struct mmc_config cfg; struct mmc mmc; }; struct tegra_mmc_priv { struct tegra_mmc *reg; struct reset_ctl reset_ctl; struct clk clk; struct gpio_desc cd_gpio; /* Change Detect GPIO */ struct gpio_desc pwr_gpio; /* Power GPIO */ struct gpio_desc wp_gpio; /* Write Protect GPIO */ unsigned int version; /* SDHCI spec. version */ unsigned int clock; /* Current clock (MHz) */ int mmc_id; /* peripheral id */ int tap_value; int trim_value; }; static void tegra_mmc_set_power(struct tegra_mmc_priv *priv, unsigned short power) { u8 pwr = 0; debug("%s: power = %x\n", __func__, power); if (power != (unsigned short)-1) { switch (1 << power) { case MMC_VDD_165_195: pwr = TEGRA_MMC_PWRCTL_SD_BUS_VOLTAGE_V1_8; break; case MMC_VDD_29_30: case MMC_VDD_30_31: pwr = TEGRA_MMC_PWRCTL_SD_BUS_VOLTAGE_V3_0; break; case MMC_VDD_32_33: case MMC_VDD_33_34: pwr = TEGRA_MMC_PWRCTL_SD_BUS_VOLTAGE_V3_3; break; } } debug("%s: pwr = %X\n", __func__, pwr); /* Set the bus voltage first (if any) */ writeb(pwr, &priv->reg->pwrcon); if (pwr == 0) return; /* Now enable bus power */ pwr |= TEGRA_MMC_PWRCTL_SD_BUS_POWER; writeb(pwr, &priv->reg->pwrcon); } static void tegra_mmc_prepare_data(struct tegra_mmc_priv *priv, struct mmc_data *data, struct bounce_buffer *bbstate) { unsigned char ctrl; debug("buf: %p (%p), data->blocks: %u, data->blocksize: %u\n", bbstate->bounce_buffer, bbstate->user_buffer, data->blocks, data->blocksize); writel((u32)(unsigned long)bbstate->bounce_buffer, &priv->reg->sysad); /* * DMASEL[4:3] * 00 = Selects SDMA * 01 = Reserved * 10 = Selects 32-bit Address ADMA2 * 11 = Selects 64-bit Address ADMA2 */ ctrl = readb(&priv->reg->hostctl); ctrl &= ~TEGRA_MMC_HOSTCTL_DMASEL_MASK; ctrl |= TEGRA_MMC_HOSTCTL_DMASEL_SDMA; writeb(ctrl, &priv->reg->hostctl); /* We do not handle DMA boundaries, so set it to max (512 KiB) */ writew((7 << 12) | (data->blocksize & 0xFFF), &priv->reg->blksize); writew(data->blocks, &priv->reg->blkcnt); } static void tegra_mmc_set_transfer_mode(struct tegra_mmc_priv *priv, struct mmc_data *data) { unsigned short mode; debug(" mmc_set_transfer_mode called\n"); /* * TRNMOD * MUL1SIN0[5] : Multi/Single Block Select * RD1WT0[4] : Data Transfer Direction Select * 1 = read * 0 = write * ENACMD12[2] : Auto CMD12 Enable * ENBLKCNT[1] : Block Count Enable * ENDMA[0] : DMA Enable */ mode = (TEGRA_MMC_TRNMOD_DMA_ENABLE | TEGRA_MMC_TRNMOD_BLOCK_COUNT_ENABLE); if (data->blocks > 1) mode |= TEGRA_MMC_TRNMOD_MULTI_BLOCK_SELECT; if (data->flags & MMC_DATA_READ) mode |= TEGRA_MMC_TRNMOD_DATA_XFER_DIR_SEL_READ; writew(mode, &priv->reg->trnmod); } static int tegra_mmc_wait_inhibit(struct tegra_mmc_priv *priv, struct mmc_cmd *cmd, struct mmc_data *data, unsigned int timeout) { /* * PRNSTS * CMDINHDAT[1] : Command Inhibit (DAT) * CMDINHCMD[0] : Command Inhibit (CMD) */ unsigned int mask = TEGRA_MMC_PRNSTS_CMD_INHIBIT_CMD; /* * We shouldn't wait for data inhibit for stop commands, even * though they might use busy signaling */ if ((data == NULL) && (cmd->resp_type & MMC_RSP_BUSY)) mask |= TEGRA_MMC_PRNSTS_CMD_INHIBIT_DAT; while (readl(&priv->reg->prnsts) & mask) { if (timeout == 0) { printf("%s: timeout error\n", __func__); return -1; } timeout--; udelay(1000); } return 0; } static int tegra_mmc_send_cmd_bounced(struct udevice *dev, struct mmc_cmd *cmd, struct mmc_data *data, struct bounce_buffer *bbstate) { struct tegra_mmc_priv *priv = dev_get_priv(dev); int flags, i; int result; unsigned int mask = 0; unsigned int retry = 0x100000; debug(" mmc_send_cmd called\n"); result = tegra_mmc_wait_inhibit(priv, cmd, data, 10 /* ms */); if (result < 0) return result; if (data) tegra_mmc_prepare_data(priv, data, bbstate); debug("cmd->arg: %08x\n", cmd->cmdarg); writel(cmd->cmdarg, &priv->reg->argument); if (data) tegra_mmc_set_transfer_mode(priv, data); if ((cmd->resp_type & MMC_RSP_136) && (cmd->resp_type & MMC_RSP_BUSY)) return -1; /* * CMDREG * CMDIDX[13:8] : Command index * DATAPRNT[5] : Data Present Select * ENCMDIDX[4] : Command Index Check Enable * ENCMDCRC[3] : Command CRC Check Enable * RSPTYP[1:0] * 00 = No Response * 01 = Length 136 * 10 = Length 48 * 11 = Length 48 Check busy after response */ if (!(cmd->resp_type & MMC_RSP_PRESENT)) flags = TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_NO_RESPONSE; else if (cmd->resp_type & MMC_RSP_136) flags = TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_LENGTH_136; else if (cmd->resp_type & MMC_RSP_BUSY) flags = TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_LENGTH_48_BUSY; else flags = TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_LENGTH_48; if (cmd->resp_type & MMC_RSP_CRC) flags |= TEGRA_MMC_TRNMOD_CMD_CRC_CHECK; if (cmd->resp_type & MMC_RSP_OPCODE) flags |= TEGRA_MMC_TRNMOD_CMD_INDEX_CHECK; if (data) flags |= TEGRA_MMC_TRNMOD_DATA_PRESENT_SELECT_DATA_TRANSFER; debug("cmd: %d\n", cmd->cmdidx); writew((cmd->cmdidx << 8) | flags, &priv->reg->cmdreg); for (i = 0; i < retry; i++) { mask = readl(&priv->reg->norintsts); /* Command Complete */ if (mask & TEGRA_MMC_NORINTSTS_CMD_COMPLETE) { if (!data) writel(mask, &priv->reg->norintsts); break; } } if (i == retry) { printf("%s: waiting for status update\n", __func__); writel(mask, &priv->reg->norintsts); return -ETIMEDOUT; } if (mask & TEGRA_MMC_NORINTSTS_CMD_TIMEOUT) { /* Timeout Error */ debug("timeout: %08x cmd %d\n", mask, cmd->cmdidx); writel(mask, &priv->reg->norintsts); return -ETIMEDOUT; } else if (mask & TEGRA_MMC_NORINTSTS_ERR_INTERRUPT) { /* Error Interrupt */ debug("error: %08x cmd %d\n", mask, cmd->cmdidx); writel(mask, &priv->reg->norintsts); return -1; } if (cmd->resp_type & MMC_RSP_PRESENT) { if (cmd->resp_type & MMC_RSP_136) { /* CRC is stripped so we need to do some shifting. */ for (i = 0; i < 4; i++) { unsigned long offset = (unsigned long) (&priv->reg->rspreg3 - i); cmd->response[i] = readl(offset) << 8; if (i != 3) { cmd->response[i] |= readb(offset - 1); } debug("cmd->resp[%d]: %08x\n", i, cmd->response[i]); } } else if (cmd->resp_type & MMC_RSP_BUSY) { for (i = 0; i < retry; i++) { /* PRNTDATA[23:20] : DAT[3:0] Line Signal */ if (readl(&priv->reg->prnsts) & (1 << 20)) /* DAT[0] */ break; } if (i == retry) { printf("%s: card is still busy\n", __func__); writel(mask, &priv->reg->norintsts); return -ETIMEDOUT; } cmd->response[0] = readl(&priv->reg->rspreg0); debug("cmd->resp[0]: %08x\n", cmd->response[0]); } else { cmd->response[0] = readl(&priv->reg->rspreg0); debug("cmd->resp[0]: %08x\n", cmd->response[0]); } } if (data) { unsigned long start = get_timer(0); while (1) { mask = readl(&priv->reg->norintsts); if (mask & TEGRA_MMC_NORINTSTS_ERR_INTERRUPT) { /* Error Interrupt */ writel(mask, &priv->reg->norintsts); printf("%s: error during transfer: 0x%08x\n", __func__, mask); return -1; } else if (mask & TEGRA_MMC_NORINTSTS_DMA_INTERRUPT) { /* * DMA Interrupt, restart the transfer where * it was interrupted. */ unsigned int address = readl(&priv->reg->sysad); debug("DMA end\n"); writel(TEGRA_MMC_NORINTSTS_DMA_INTERRUPT, &priv->reg->norintsts); writel(address, &priv->reg->sysad); } else if (mask & TEGRA_MMC_NORINTSTS_XFER_COMPLETE) { /* Transfer Complete */ debug("r/w is done\n"); break; } else if (get_timer(start) > 8000UL) { writel(mask, &priv->reg->norintsts); printf("%s: MMC Timeout\n" " Interrupt status 0x%08x\n" " Interrupt status enable 0x%08x\n" " Interrupt signal enable 0x%08x\n" " Present status 0x%08x\n", __func__, mask, readl(&priv->reg->norintstsen), readl(&priv->reg->norintsigen), readl(&priv->reg->prnsts)); return -1; } } writel(mask, &priv->reg->norintsts); } udelay(1000); return 0; } static int tegra_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd, struct mmc_data *data) { void *buf; unsigned int bbflags; size_t len; struct bounce_buffer bbstate; int ret; if (data) { if (data->flags & MMC_DATA_READ) { buf = data->dest; bbflags = GEN_BB_WRITE; } else { buf = (void *)data->src; bbflags = GEN_BB_READ; } len = data->blocks * data->blocksize; bounce_buffer_start(&bbstate, buf, len, bbflags); } ret = tegra_mmc_send_cmd_bounced(dev, cmd, data, &bbstate); if (data) bounce_buffer_stop(&bbstate); return ret; } static void tegra_mmc_change_clock(struct tegra_mmc_priv *priv, uint clock) { ulong rate; int div; unsigned short clk; unsigned long timeout; debug(" mmc_change_clock called\n"); /* * Change Tegra SDMMCx clock divisor here. Source is PLLP_OUT0 */ if (clock == 0) goto out; rate = clk_set_rate(&priv->clk, clock); div = (rate + clock - 1) / clock; #if defined(CONFIG_TEGRA210) if (priv->mmc_id == PERIPH_ID_SDMMC1 && clock <= 400000) { /* clock_adjust_periph_pll_div() chooses a 'bad' clock * on SDMMC1 T210, so skip it here and force a clock * that's been spec'd in the table in the TRM for * card-detect (400KHz). */ uint effective_rate = clock_adjust_periph_pll_div(priv->mmc_id, CLOCK_ID_PERIPH, 24727273, NULL); div = 62; debug("%s: WAR: Using SDMMC1 clock of %u, div %d to achieve %dHz card clock ...\n", __func__, effective_rate, div, clock); } else { clock_adjust_periph_pll_div(priv->mmc_id, CLOCK_ID_PERIPH, clock, &div); } #endif debug("div = %d\n", div); writew(0, &priv->reg->clkcon); /* * CLKCON * SELFREQ[15:8] : base clock divided by value * ENSDCLK[2] : SD Clock Enable * STBLINTCLK[1] : Internal Clock Stable * ENINTCLK[0] : Internal Clock Enable */ div >>= 1; clk = ((div << TEGRA_MMC_CLKCON_SDCLK_FREQ_SEL_SHIFT) | TEGRA_MMC_CLKCON_INTERNAL_CLOCK_ENABLE); writew(clk, &priv->reg->clkcon); /* Wait max 10 ms */ timeout = 10; while (!(readw(&priv->reg->clkcon) & TEGRA_MMC_CLKCON_INTERNAL_CLOCK_STABLE)) { if (timeout == 0) { printf("%s: timeout error\n", __func__); return; } timeout--; udelay(1000); } clk |= TEGRA_MMC_CLKCON_SD_CLOCK_ENABLE; writew(clk, &priv->reg->clkcon); debug("mmc_change_clock: clkcon = %08X\n", clk); out: priv->clock = clock; } static int tegra_mmc_set_ios(struct udevice *dev) { struct tegra_mmc_priv *priv = dev_get_priv(dev); struct mmc *mmc = mmc_get_mmc_dev(dev); unsigned char ctrl; debug(" mmc_set_ios called\n"); debug("bus_width: %x, clock: %d\n", mmc->bus_width, mmc->clock); /* Change clock first */ tegra_mmc_change_clock(priv, mmc->clock); ctrl = readb(&priv->reg->hostctl); /* * WIDE8[5] * 0 = Depend on WIDE4 * 1 = 8-bit mode * WIDE4[1] * 1 = 4-bit mode * 0 = 1-bit mode */ if (mmc->bus_width == 8) ctrl |= (1 << 5); else if (mmc->bus_width == 4) ctrl |= (1 << 1); else ctrl &= ~(1 << 1 | 1 << 5); writeb(ctrl, &priv->reg->hostctl); debug("mmc_set_ios: hostctl = %08X\n", ctrl); return 0; } static void tegra_mmc_pad_init(struct tegra_mmc_priv *priv) { #if defined(CONFIG_TEGRA30) || defined(CONFIG_TEGRA210) u32 val; u16 clk_con; int timeout; int id = priv->mmc_id; debug("%s: sdmmc address = %p, id = %d\n", __func__, priv->reg, id); /* Set the pad drive strength for SDMMC1 or 3 only */ if (id != PERIPH_ID_SDMMC1 && id != PERIPH_ID_SDMMC3) { debug("%s: settings are only valid for SDMMC1/SDMMC3!\n", __func__); return; } val = readl(&priv->reg->sdmemcmppadctl); val &= 0xFFFFFFF0; val |= MEMCOMP_PADCTRL_VREF; writel(val, &priv->reg->sdmemcmppadctl); /* Disable SD Clock Enable before running auto-cal as per TRM */ clk_con = readw(&priv->reg->clkcon); debug("%s: CLOCK_CONTROL = 0x%04X\n", __func__, clk_con); clk_con &= ~TEGRA_MMC_CLKCON_SD_CLOCK_ENABLE; writew(clk_con, &priv->reg->clkcon); val = readl(&priv->reg->autocalcfg); val &= 0xFFFF0000; val |= AUTO_CAL_PU_OFFSET | AUTO_CAL_PD_OFFSET; writel(val, &priv->reg->autocalcfg); val |= AUTO_CAL_START | AUTO_CAL_ENABLE; writel(val, &priv->reg->autocalcfg); debug("%s: AUTO_CAL_CFG = 0x%08X\n", __func__, val); udelay(1); timeout = 100; /* 10 mSec max (100*100uS) */ do { val = readl(&priv->reg->autocalsts); udelay(100); } while ((val & AUTO_CAL_ACTIVE) && --timeout); val = readl(&priv->reg->autocalsts); debug("%s: Final AUTO_CAL_STATUS = 0x%08X, timeout = %d\n", __func__, val, timeout); /* Re-enable SD Clock Enable when auto-cal is done */ clk_con |= TEGRA_MMC_CLKCON_SD_CLOCK_ENABLE; writew(clk_con, &priv->reg->clkcon); clk_con = readw(&priv->reg->clkcon); debug("%s: final CLOCK_CONTROL = 0x%04X\n", __func__, clk_con); if (timeout == 0) { printf("%s: Warning: Autocal timed out!\n", __func__); /* TBD: Set CFG2TMC_SDMMC1_PAD_CAL_DRV* regs here */ } #endif /* T30/T210 */ } static void tegra_mmc_reset(struct tegra_mmc_priv *priv, struct mmc *mmc) { unsigned int timeout; debug(" mmc_reset called\n"); /* * RSTALL[0] : Software reset for all * 1 = reset * 0 = work */ writeb(TEGRA_MMC_SWRST_SW_RESET_FOR_ALL, &priv->reg->swrst); priv->clock = 0; /* Wait max 100 ms */ timeout = 100; /* hw clears the bit when it's done */ while (readb(&priv->reg->swrst) & TEGRA_MMC_SWRST_SW_RESET_FOR_ALL) { if (timeout == 0) { printf("%s: timeout error\n", __func__); return; } timeout--; udelay(1000); } /* Set SD bus voltage & enable bus power */ tegra_mmc_set_power(priv, fls(mmc->cfg->voltages) - 1); debug("%s: power control = %02X, host control = %02X\n", __func__, readb(&priv->reg->pwrcon), readb(&priv->reg->hostctl)); /* Make sure SDIO pads are set up */ tegra_mmc_pad_init(priv); if (!IS_ERR_VALUE(priv->tap_value) || !IS_ERR_VALUE(priv->trim_value)) { u32 val; val = readl(&priv->reg->venclkctl); val &= ~TRIM_VAL_MASK; val |= (priv->trim_value << TRIM_VAL_SHIFT); val &= ~TAP_VAL_MASK; val |= (priv->tap_value << TAP_VAL_SHIFT); writel(val, &priv->reg->venclkctl); debug("%s: VENDOR_CLOCK_CNTRL = 0x%08X\n", __func__, val); } } static int tegra_mmc_init(struct udevice *dev) { struct tegra_mmc_priv *priv = dev_get_priv(dev); struct mmc *mmc = mmc_get_mmc_dev(dev); unsigned int mask; debug(" tegra_mmc_init called\n"); #if defined(CONFIG_TEGRA210) priv->mmc_id = clock_decode_periph_id(dev); if (priv->mmc_id == PERIPH_ID_NONE) { printf("%s: Missing/invalid peripheral ID\n", __func__); return -EINVAL; } #endif tegra_mmc_reset(priv, mmc); #if defined(CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK) /* * Disable the external clock loopback and use the internal one on * SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0 register's SDMMC_SPARE1 * bits being set to 0xfffd according to the TRM. * * TODO(marcel.ziswiler@toradex.com): Move to device tree controlled * approach once proper kernel integration made it mainline. */ if (priv->reg == (void *)0x700b0400) { mask = readl(&priv->reg->venmiscctl); mask &= ~TEGRA_MMC_MISCON_ENABLE_EXT_LOOPBACK; writel(mask, &priv->reg->venmiscctl); } #endif priv->version = readw(&priv->reg->hcver); debug("host version = %x\n", priv->version); /* mask all */ writel(0xffffffff, &priv->reg->norintstsen); writel(0xffffffff, &priv->reg->norintsigen); writeb(0xe, &priv->reg->timeoutcon); /* TMCLK * 2^27 */ /* * NORMAL Interrupt Status Enable Register init * [5] ENSTABUFRDRDY : Buffer Read Ready Status Enable * [4] ENSTABUFWTRDY : Buffer write Ready Status Enable * [3] ENSTADMAINT : DMA boundary interrupt * [1] ENSTASTANSCMPLT : Transfre Complete Status Enable * [0] ENSTACMDCMPLT : Command Complete Status Enable */ mask = readl(&priv->reg->norintstsen); mask &= ~(0xffff); mask |= (TEGRA_MMC_NORINTSTSEN_CMD_COMPLETE | TEGRA_MMC_NORINTSTSEN_XFER_COMPLETE | TEGRA_MMC_NORINTSTSEN_DMA_INTERRUPT | TEGRA_MMC_NORINTSTSEN_BUFFER_WRITE_READY | TEGRA_MMC_NORINTSTSEN_BUFFER_READ_READY); writel(mask, &priv->reg->norintstsen); /* * NORMAL Interrupt Signal Enable Register init * [1] ENSTACMDCMPLT : Transfer Complete Signal Enable */ mask = readl(&priv->reg->norintsigen); mask &= ~(0xffff); mask |= TEGRA_MMC_NORINTSIGEN_XFER_COMPLETE; writel(mask, &priv->reg->norintsigen); return 0; } static int tegra_mmc_getcd(struct udevice *dev) { struct tegra_mmc_priv *priv = dev_get_priv(dev); debug("tegra_mmc_getcd called\n"); if (dm_gpio_is_valid(&priv->cd_gpio)) return dm_gpio_get_value(&priv->cd_gpio); return 1; } static const struct dm_mmc_ops tegra_mmc_ops = { .send_cmd = tegra_mmc_send_cmd, .set_ios = tegra_mmc_set_ios, .get_cd = tegra_mmc_getcd, }; static int tegra_mmc_probe(struct udevice *dev) { struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); struct tegra_mmc_plat *plat = dev_get_plat(dev); struct tegra_mmc_priv *priv = dev_get_priv(dev); struct mmc_config *cfg = &plat->cfg; int bus_width, ret; cfg->name = dev->name; bus_width = dev_read_u32_default(dev, "bus-width", 1); cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195; cfg->host_caps = 0; if (bus_width == 8) cfg->host_caps |= MMC_MODE_8BIT; if (bus_width >= 4) cfg->host_caps |= MMC_MODE_4BIT; cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS; /* * min freq is for card identification, and is the highest * low-speed SDIO card frequency (actually 400KHz) * max freq is highest HS eMMC clock as per the SD/MMC spec * (actually 52MHz) */ cfg->f_min = 375000; cfg->f_max = dev_read_u32_default(dev, "max-frequency", 48000000); cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; priv->reg = dev_read_addr_ptr(dev); ret = reset_get_by_name(dev, "sdhci", &priv->reset_ctl); if (ret) { debug("reset_get_by_name() failed: %d\n", ret); return ret; } ret = clk_get_by_index(dev, 0, &priv->clk); if (ret) { debug("clk_get_by_index() failed: %d\n", ret); return ret; } ret = reset_assert(&priv->reset_ctl); if (ret) return ret; ret = clk_enable(&priv->clk); if (ret) return ret; ret = clk_set_rate(&priv->clk, 20000000); if (IS_ERR_VALUE(ret)) return ret; ret = reset_deassert(&priv->reset_ctl); if (ret) return ret; /* These GPIOs are optional */ gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio, GPIOD_IS_IN); gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio, GPIOD_IS_IN); gpio_request_by_name(dev, "power-gpios", 0, &priv->pwr_gpio, GPIOD_IS_OUT); if (dm_gpio_is_valid(&priv->pwr_gpio)) dm_gpio_set_value(&priv->pwr_gpio, 1); ret = dev_read_u32(dev, "nvidia,default-tap", &priv->tap_value); if (ret) priv->tap_value = ret; ret = dev_read_u32(dev, "nvidia,default-trim", &priv->trim_value); if (ret) priv->trim_value = ret; upriv->mmc = &plat->mmc; return tegra_mmc_init(dev); } static int tegra_mmc_bind(struct udevice *dev) { struct tegra_mmc_plat *plat = dev_get_plat(dev); return mmc_bind(dev, &plat->mmc, &plat->cfg); } static const struct udevice_id tegra_mmc_ids[] = { { .compatible = "nvidia,tegra20-sdhci" }, { .compatible = "nvidia,tegra30-sdhci" }, { .compatible = "nvidia,tegra114-sdhci" }, { .compatible = "nvidia,tegra124-sdhci" }, { .compatible = "nvidia,tegra210-sdhci" }, { .compatible = "nvidia,tegra186-sdhci" }, { } }; U_BOOT_DRIVER(tegra_mmc_drv) = { .name = "tegra_mmc", .id = UCLASS_MMC, .of_match = tegra_mmc_ids, .bind = tegra_mmc_bind, .probe = tegra_mmc_probe, .ops = &tegra_mmc_ops, .plat_auto = sizeof(struct tegra_mmc_plat), .priv_auto = sizeof(struct tegra_mmc_priv), };