From 2b8e8d2671227473c9698859db38fefa328b87d0 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 17 Feb 2016 13:34:22 -0200 Subject: mx7dsabresd: Make 'ums' command functional When running the 'ums' command we get: => ums 0 mmc 0 UMS: disk start sector: 0x0, count: 0xe18000 g_dnl_register: failed!, error: -22 ERROR: g_dnl_register failed at common/cmd_usb_mass_storage.c:107/do_usb_mass_storage() Fix this by initializing USB OTG1 port as USB device mode instead of host. Signed-off-by: Fabio Estevam --- board/freescale/mx7dsabresd/mx7dsabresd.c | 41 ++++++++++++++----------------- 1 file changed, 18 insertions(+), 23 deletions(-) (limited to 'board') diff --git a/board/freescale/mx7dsabresd/mx7dsabresd.c b/board/freescale/mx7dsabresd/mx7dsabresd.c index 20e56f281b..782acc6713 100644 --- a/board/freescale/mx7dsabresd/mx7dsabresd.c +++ b/board/freescale/mx7dsabresd/mx7dsabresd.c @@ -23,6 +23,7 @@ #include #include #include +#include #include DECLARE_GLOBAL_DATA_PTR; @@ -111,6 +112,14 @@ static iomux_v3_cfg_t const usdhc3_emmc_pads[] = { MX7D_PAD_SD3_RESET_B__GPIO6_IO11 | MUX_PAD_CTRL(USDHC_PAD_CTRL), }; +static iomux_v3_cfg_t const usb_otg1_pads[] = { + MX7D_PAD_GPIO1_IO05__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t const usb_otg2_pads[] = { + MX7D_PAD_UART3_CTS_B__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + #define IOX_SDI IMX_GPIO_NR(1, 9) #define IOX_STCP IMX_GPIO_NR(1, 12) #define IOX_SHCP IMX_GPIO_NR(1, 13) @@ -511,6 +520,10 @@ int board_early_init_f(void) setup_iomux_uart(); setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); + imx_iomux_v3_setup_multiple_pads(usb_otg1_pads, + ARRAY_SIZE(usb_otg1_pads)); + imx_iomux_v3_setup_multiple_pads(usb_otg2_pads, + ARRAY_SIZE(usb_otg2_pads)); return 0; } @@ -602,29 +615,11 @@ int checkboard(void) } #ifdef CONFIG_USB_EHCI_MX7 -static iomux_v3_cfg_t const usb_otg1_pads[] = { - MX7D_PAD_GPIO1_IO05__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static iomux_v3_cfg_t const usb_otg2_pads[] = { - MX7D_PAD_UART3_CTS_B__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -int board_ehci_hcd_init(int port) +int board_usb_phy_mode(int port) { - switch (port) { - case 0: - imx_iomux_v3_setup_multiple_pads(usb_otg1_pads, - ARRAY_SIZE(usb_otg1_pads)); - break; - case 1: - imx_iomux_v3_setup_multiple_pads(usb_otg2_pads, - ARRAY_SIZE(usb_otg2_pads)); - break; - default: - printf("MXC USB port %d not yet supported\n", port); - return -EINVAL; - } - return 0; + if (port == 0) + return USB_INIT_DEVICE; + else + return USB_INIT_HOST; } #endif -- cgit v1.2.3