| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When CONFIG_SYS_REDUNDAND_ENVIRONMENT is enabled, by default env is
getting saved to redundant environment irrespective of primary env is
present or not.
It means even if primary and redundant environment are not present, by
default, env is getting stored to redundant environment. Even if primary
env is present, it is choosing to store in redudndant env.
Ideally it should look for primary env and choose to store in primary env
if it is present. If both primary and redundant env are not present then
it should save in to primary env area.
Fix the issue by making env_valid = ENV_INVALID when both the
environments are not present.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The new opt-out setting, CONFIG_ENV_MMC_PARTITION, statically sets
the MMC environment partition name. Prior to this patch, the only way
to declare this partition name was by creating a
'u-boot,mmc-env-partition' parameter in the device-tree's /config node.
This setting provides additional flexibility, particularly in cases
where accessing the device-tree is not straightforward (e.g. QEMU).
If undeclared, the device-tree's setting will be used.
Signed-off-by: Emmanuel Di Fede <emmanuel.difede@cysec.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab81058364b
("env: Complete generic support for writable list"). Remove leftover of
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
|
|
Avoid error messages when SPL,TPL,VPL build don't
have the environment options of the main build.
This is needed when defined(CONFIG_ENV_IS_IN_xxx) is changed
to CONFIG_IS_ENABLED(ENV_IS_IN_xxx).
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
|
|
Add an option to put the VPL environment nowhere (not in storage).
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Apply the GPT U-Boot environment GUID type look up only on eMMC user
HW partition, do not apply the look up on eMMC boot HW partitions as
mmc_offset_try_partition() assumes either SD partitions or eMMC user
HW partition.
This fixes environment operation on systems where CONFIG_SYS_MMC_ENV_PART
is non-zero and CONFIG_SYS_REDUNDAND_ENVIRONMENT is set.
Fixes: 80105d8fd52 ("env: mmc: select GPT env partition by type guid")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Boards may set networking variables programmatically, thus may have
CONFIG_NET on but CONFIG_CMD_NET off. The IOT2050 is an example.
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This completes what 890feecaab72 started by selecting ENV_APPEND and
loading the default env before any other sources. This ensures that load
operations pick up all non-writable vars from the default env and only
permitted parts from other locations according to the regular
priorities.
With this change, boards only need to define the list of writable
variables but no longer have to provide a custom env_get_location
implementation.
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Marek Vasut <marex@denx.de>
CC: Stefan Herbrechtsmeier <stefan.herbrechtsmeier-oss@weidmueller.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
This is not used anywhere, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Fix the issue in commit 46c9016 ("env: mcc: Drop unnecessary #ifdefs")
If CONFIG_SYS_REDUNDAND_ENVIRONMENT is not defined, the offset value
becomes undetermined, so write env to unexpected offset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Add trace in env save to indicate any errors to end user and avoid
silent output when the command 'env erase' is not executed as it is
done in env_save with commit 8968288cb477 ("env: add failing trace in
env_save")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Add support of opts erase for ubi env backend, this opts is used by
command 'env erase'.
This command only zero-fill the env UBI volume CONFIG_ENV_UBI_VOLUME
and CONFIG_ENV_UBI_VOLUME_REDUND, so the saved environment becomes
invalid.
This patch introduces a local define ENV_UBI_VOLUME_REDUND
only to avoid #if in the code, as CONFIG_ENV_UBI_VOLUME_REDUND
is only defined when CONFIG_SYS_REDUNDAND_ENVIRONMENT is defined.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Remove the unused macro STR(X) since the commit 2b2f727500dc ("env: mmc:
allow support of mmc_get_env_dev with OF_CONTROL")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add a debug message to indicate a potential issue when
"u-boot,mmc-env-partition" is present in config node of device tree
but this partition name is not found in the mmc device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Since commit c0364ce1c695 ("doc/README.gpt: define partition type GUID for
U-Boot environment"), a specific type GUID can be used to indicate
the U-Boot environment partition on the device with GPT partition table.
This patch uses this type GUID to found the env partition as fallback
when the partition name property "u-boot,mmc-env-partition" is not present
in config node or if the indicated partition name is not found.
The mmc_offset_try_partition() function is reused, it selects the first
partition with the correct type GUID when the parameter 'str' is NULL.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add a new config CONFIG_ENV_MMC_USE_DT to force configuration of the
U-Boot environment offset with device tree config node.
This patch avoids issues when several CONFIG_ENV_IS_IN_XXX are activated,
the defconfig file uses the same value for CONFIG_ENV_OFFSET or
CONFIG_ENV_OFFSET_REDUND for the several ENV backends (SPI_FLASH, EEPROM
NAND, SATA, MMC).
After this patch a bad offset value is not possible when the selected
partition in device tree is not found.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
When ENV_IS_EMBEDDED is enabled, ret is not defined but is used as a
return value in env_mmc_load().
This patch correct this issue and simplify the existing code, test only
one time #if defined(ENV_IS_EMBEDDED) and not in the function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
This file has a lot of conditional code and much of it is unnecessary.
Clean this up to reduce the number of build combinations.
This patch replaces the test on CONFIG_ENV_OFFSET_REDUND for the
more coherent CONFIG_SYS_REDUNDAND_ENVIRONMENT.
This patch also corrects a compilation issue in init_mmc_for_env()
when CONFIG_SYS_MMC_ENV_PART is not activated, env_mmc_orig_hwpart is
not defined.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Introduce ENV_MMC_OFFSET defines.
It is a preliminary step to the next patches to simplify the code.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_OVERWRITE_ETHADDR_ONCE
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This functionality is currently unused, and has not been migrated to
using DM_I2C, even. Drop this.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_GATEWAYIP
CONFIG_HOSTNAME
CONFIG_IPADDR
CONFIG_NETMASK
CONFIG_ROOTPATH
CONFIG_SERVERIP
CONFIG_UBOOTPATH
To do this, we introduce a CONFIG_USE_ form of each of the above and
change include/env_default.h to test for that to be set before setting a
value. Further, we don't want to stringify the IP address related values
as they are now properly strings via Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This option is unused anywhere and likely untested for quite a long
while. Drop this support code.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Drop CONFIG_BUILD_ENVCRC as this is never set directly but instead
means ENV_IS_EMBEDDED, so reference that in code and rename the Makefile
usage to BUILD_ENVCRC.
- Remove extra-$(CONFIG_ENV_IS_EMBEDDED) line as it could never be true,
and likely why there is an extra- line for CONFIG_ENV_IS_IN_FLASH (the
only use case today of embedded environments).
- With these slight changes we can then see that using the calculated
symbol of ENV_IS_EMBEDDED is the right thing to use in any code which
needs to know this situation and can remove CONFIG_ENV_IS_EMBEDDED
entirely.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The current name is quite unwieldy. Change it to use an ofprop_ prefix
and shorten it. Fix the return-value comment while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Drop the 'get' in these names since it does not fit with the rest of
the API.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Versal NET platform is based on Versal chip which is reusing a lot of IPs.
For more information about new IPs please take a look at DT which describe
currently supported devices.
The patch is adding architecture and board support with soc detection
algorithm. Generic setting should be very similar to Versal but it will
likely diverge in longer run.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/320206853dc370ce290a4e7b6d0bb26b05206021.1663589964.git.michal.simek@amd.com
|
|
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
|
|
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
ENV_OFFSET_REDUND config is by default set to 0 for flashes. Saving the env
variables is overwriting data at 0 offset, which is wrong. So add default
redund env offset for Zynq, ZynqMP, Versal and microblaze platforms.
Configured ENV_OFFSET_REDUND offsets by ENV_OFFSET + (2 * ENV_SIZE).
In case of versal, we configured ENV_OFFSET_REDUND at 0x7F00000 instead
of 0x7F80000. As BOOT_SCRIPT_OFFSET is already configured at 0x7F80000.
Added ENV_OFFSET_REDUND in Kconfig for microblaze due to dependency of
ENV_IS_IN_SPI_FLASH config.
Below table specifies platform specific env and env redund offsets.
PLAT ENV_OFFSET ENV_OFFSET_REDUND
---- ---------- -----------------
ZYNQ 0xE0000 0xE40000
ZYNQMP 0x1E00000 0x1E80000
VERSAL 0x7F40000 0x7F00000
MICROBLAZE 0x1080000 0x10C0000
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/92656dc08f0f5a749d62b71ca6e77fe1be72e9e0.1661340204.git.michal.simek@amd.com
|
|
A large number of files include <flash.h> as it used to be how various
SPI flash related functions were found, or for other reasons entirely.
In order to migrate some further CONFIG symbols to Kconfig we need to
not include flash.h in cases where we don't have a NOR flash of some
sort enabled. Furthermore, in cases where we are in common code and it
doesn't make sense to try and further refactor the code itself in to new
files we need to guard this inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When having environment stored in EXT4 or FAT
and using an AHCI or SCSI device / partition
the scan would not be performed early enough
and hence the device would not be recognized.
This change adds the scan when the interface
is "scsi" in a similar way to mmc_initialize.
Signed-off-by: Rogier Stam <rogier@unrailed.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
|
|
This converts the following to Kconfig:
CONFIG_ENV_RANGE
Now that this is in Kconfig we can enforce a minimum size and so remove
the check in C code to ensure range is larger than size.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_ENV_MIN_ENTRIES
CONFIG_ENV_MAX_ENTRIES
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
On eMMC device, the erase_grp_size > 1 so the address and size for the
erase block command in env/mmc.c can be unaligned on erase group size and
some strange trace occurs and the result is not guarantee by MMC devices.
The SD-Card behavior doesn't change as erase_grp_size = 1 for SD-Card.
For example, on eMMC present on STM32MP15C-EV1 and before the patch:
STM32MP> env erase
Erasing Environment on MMC...
Caution! Your devices Erase group is 0x400
The erase range would be change to 0x2000~0x27ff
16 blocks erased: OK
Caution! Your devices Erase group is 0x400
The erase range would be change to 0x2000~0x23ff
16 blocks erased: OK
OK
After this patch:
STM32MP> env erase
Erasing Environment on MMC...
1024 blocks erased at 0x2000: OK
1024 blocks erased at 0x2000: OK
OK
Here the 2 copies of U-Boot environment are in the same devices Erase
group: it is erased twice.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Now, spi_flash_probe_bus_cs() relies on DT for spi speed and mode
and logically calls spi_get_bus_and_cs(). In case spi mode and speed are
not read from DT, make usage of spi_flash_probe() instead.
To sum-up:
- Previous call tree was:
spi_flash_probe() -> spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
- Current call tree is:
spi_flash_probe() -> _spi_get_bus_and_cs()
spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
This patch impacts the following :
- cmd/sf.c: if spi mode and/or speed is passed in argument of
do_spi_flash_probe(), call spi_flash_probe() otherwise call
spi_flash_probe_bus_cs().
- drivers/net/fm/fm.c: as by default spi speed and mode was set to
0 and a comment indicates that speed and mode are read from DT,
use spi_flash_probe_bus_cs().
- drivers/net/pfe_eth/pfe_firmware.c: spi speed and mode are not read
from DT by all platforms using this driver, so keep legacy and replace
spi_flash_probe_bus_cs() by spi_flash_probe();
- drivers/net/sni_netsec.c : spi speed and mode are not read from DT,
so replace spi_flash_probe_bus_cs() by spi_flash_probe().
- drivers/usb/gadget/max3420_udc.c: Can't find any platform which make
usage of this driver, nevertheless, keep legacy and replace
spi_get_bus_and_cs() by _spi_get_bus_and_cs().
- env/sf.c: a comment indicates that speed and mode are read
from DT. So use spi_flash_probe_bus_cs().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
|
|
In some cases it makes sense to use env_sf_init_addr() also in SPL mode.
Allow it for boards by providing custom implementation of weak function
env_sf_get_env_addr(). When this function returns NULL it signals that
address is invalid, like config option CONFIG_ENV_ADDR.
There is no change in default behavior or in config options.
Signed-off-by: Pali Rohár <pali@kernel.org>
|
|
Currently there is only one way to override desired environment location,
by implementing env_get_location(). This is increasingly being conflated
both on board level and architecture level, which leads to a problem on
boards where this function is already implemented on architecture level,
since those boards have no way to override this environment location on
board level anymore.
Implement arch_env_get_location() function which is architecture specific
and should only ever be implemented in architecture code. This function
has lower priority than env_get_location(), which should only ever be
implemented in board code, and which overrides the arch_env_get_location()
architecture environment selection.
This way, architecture can define its default environment chooser, while
board can now override it as needed at all times.
There is no functional change, since env_get_location() simply returns
arch_env_get_location(), and arch_env_get_location() implements the
current env_get_location() default content.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
|
|
This reverts commit 8d61237edbf6314a701cf78da2c5893a73ff5438.
This commit broke environment on literally every board I have access
to, with this revert in place, environment works as it should again.
The problem I observe with this patch is that saved environment in
either SPI NOR or eMMC is never used, the system always falls back
to default environment. The 'saveenv' command does succeed, but then
after reset, the default env is again used.
Furthermore, the commit introduced duplicate code in env_init(), this:
"
if (!prio) {
gd->env_addr = (ulong)&default_environment[0];
gd->env_valid = ENV_INVALID;
return 0;
}
if (ret == -ENOENT) {
gd->env_addr = (ulong)&default_environment[0];
gd->env_valid = ENV_INVALID;
return 0;
}
"
Furthermore, the commit is missing DCO SoB line.
Also note that upstream does not support UltraZed EG board, so
this might have been a patch pulled from downstream which did
depend on some other downstream behavior.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Felix.Vietmeyer@jila.colorado.edu <felix.vietmeyer@jila.colorado.edu>
Cc: Tom Rini <trini@konsulko.com>
|
|
For platform which can boot on different device, this allows
to override interface, device and partition from board code
Signed-off-by: He Yong <hyyoxhk@163.com>
|
|
This patch prevent u-boot from hanging on a UltraZed EG board (zynqmp).
Without the patch,
(drv = env_driver_lookup(ENVOP_INIT, prio))
evaluates to 0, causing prio = 0
Then, (!prio) is hit, returning -ENODEV causing a stall.
With the patch,
instead of returning -ENODEV and causing a stall, we
set gd->env_addr (is this really needed?)
and then
mark gd->env_valid = ENV_INVALID to use the default env.
|
|
This converts the following to Kconfig:
CONFIG_ETHPRIME
This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Prepare v2022.04-rc4
|
|
Now that sunxi uses CONFIG_SPI more sanely, and can also now properly
load the environment from SPI flash, let's enable the symbol that
actually considers the SPI flash when accessing the environment.
As this symbol depends on CONFIG_SPI, which we now only enable if the
board has a SPI flash, we can make if "default y" for all Allwinner
boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
To allow loading and storing the environment from SPI flash, adjust the
raw offset variables for Allwinner boards to make sense there.
U-Boot (including SPL and other blobs) is loaded from the beginning of
SPI flash, so move the environment location as far back as possible, to
not create unnecessary limits. As those offsets are shared with (now
mostly unused) raw MMC environment, we should respect the common one
megabyte limit, which also makes sense on SPI flash.
So limit the environment for those raw locations to 64KB, and place it
just below 1MB (@960KB).
Those values are currently unused, unless someone forcibly enables the
raw MMC environment. In this case it would break as of now, as the
current offset of 544KB is far too low for the current (arm64) U-Boot
proper.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
This converts the following to Kconfig:
CONFIG_BOOTFILE
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Sphinx expects Return: and not @return to indicate a return value.
find . -name '*.c' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;
find . -name '*.h' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
