summaryrefslogtreecommitdiff
path: root/arch/arm/mach-rockchip
AgeCommit message (Collapse)AuthorFilesLines
2022-10-19rockchip: px30: support debug uart on UART0Quentin Schulz1-2/+35
UART0 can obviously also be used for debug uart in U-Boot, so let's add its support. Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-10-19rockchip: rk3399: fix incorrect ifdef check on SPL_GPIOQuentin Schulz1-22/+28
The check to perform is on CONFIG_SPL_GPIO and not SPL_GPIO. Because this was never compiled in, it missed an include of cru.h that was not detected before. Let's include it too. Also switch to IS_ENABLED in-code check as it is the preferred inclusion/exclusion mechanism. Fixes: 07586ee4322a ("rockchip: rk3399: Support common spl_board_init") Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-10-19rockchip: rk3399: fix incorrect ifdef check on SPL_DM_REGULATORQuentin Schulz1-8/+9
The check to perform is on CONFIG_SPL_DM_REGULATOR and not SPL_DM_REGULATOR. Also switch to in-code check instead of ifdefs. Fixes: 07586ee4322a ("rockchip: rk3399: Support common spl_board_init") Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> # Rock960 Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-10-19rockchip: phycore_rk3288: remove phycore_init() functionJohan Jonker1-1/+0
The phycore_rk3288 board has a SPL size problem, so remove phycore_init() function to stay within the limits. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Wadim Egorov <w.egorov@phytec.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-09-23board_f: Fix types for board_get_usable_ram_top()Pali Rohár1-1/+1
Commit 37dc958947ed ("global_data.h: Change ram_top type to phys_addr_t") changed type of ram_top member from ulong to phys_addr_t but did not changed types in board_get_usable_ram_top() function which returns value for ram_top. So change ulong to phys_addr_t type also in board_get_usable_ram_top() signature and implementations. Fixes: 37dc958947ed ("global_data.h: Change ram_top type to phys_addr_t") Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-09-04rockchip: allow to build SPI images even without HAS_ROM optionQuentin Schulz1-4/+2
This prepares for the creation of a u-boot-rockchip-spi.bin image similar to u-boot-rockchip.bin to the exception it's destined for SPI-NOR flashes instead of MMC storage medium. Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-09-04rockchip: rk3399: sync spl_boot_devices_tbl and boot_devices node pathsQuentin Schulz1-1/+1
While technically not a bug, let's have some consistency in paths returned by u-boot,spl-boot-order look-up and the one saved in u-boot,spl-boot-device by syncing spl_boot_devices_tbl and boot_devices node paths. Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat> Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-09-04rockchip: rk3399: fix incorrect boot-device in u-boot, spl-boot-deviceQuentin Schulz1-2/+2
On RK3399, mmc0 is eMMC and mmc1 is SD card, c.f. console: MMC: mmc@fe320000: 1, mmc@fe330000: 0 In arch/arm/mach-rockchip/spl-boot-order.c:board_boot_order, the boot_device (BOOT_DEVICE_*) value is gotten from spl_node_to_boot_device function. Said function returns BOOT_DEVICE_MMC1 for mmc0 (eMMC) and BOOT_DEVICE_MMC2 for mmc1 (SD card). Since the SD card controller is at mmc@fe320000, it should be associated with BOOT_DEVICE_MMC2 and not BOOT_DEVICE_MMC1. Same applies to eMMC. Let's fix that by swapping the two BOOT_DEVICEs. Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
2022-09-04rockchip: rk3308: fix same-as-spl boot orderJohn Keeping1-0/+6
Rockchip SoCs need the boot_devices array defined in order to map the bootloader's value to a U-Boot device. Implement this for rk3308. Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-09-04rockchip: rk3399: boot_devices: fix eMMC node nameQuentin Schulz1-2/+2
When idbloader.img is flashed on the eMMC, the SPL still tries to load from SPI-NOR first. This is due to an incorrect look-up in the Device Tree. Since commit 822556a93459 ("arm: dts: sync the Rockhip 3399 SoCs from Linux"), the node name (but not label) changed from sdhci@fe330000 to mmc@fe330000 meaning U-Boot SPL is not looking for the correct node name anymore and fails to find the "same-as-spl" node when eMMC is the medium from which the SPL booted. Fixes: 822556a93459 ("arm: dts: sync the Rockhip 3399 SoCs from Linux") Cc: Quentin Schulz <foss+uboot@0leil.net> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat> Reviewed-by: Artem Lapkin <email2tema@gmail.com> Tested-by: Artem Lapkin <email2tema@gmail.com> Tested-by: Lapkin Artem <email2tema@gmail.com> Tested-by: Lapkin Artem <email2tema@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-07-11Merge branch 'next'Tom Rini7-23/+2
2022-06-29rockchip: Add option to prevent booting on power plug-inChris Morgan1-0/+10
For Rockchip boards with the all rk8xx series PMICs (excluding the rk808), it is sometimes desirable to not boot whenever the device is plugged in. An example would be for the Odroid Go Advance. This provides a configurable option to check the PMIC says it was powered because of a plug-in event. If the value is 1 and this option is selected, the device shuts down shortly after printing a message to console stating the reason why it's shutting down. Powering up the board with the power button is not affected. This patch parallels the work done in the following patch series: https://lore.kernel.org/u-boot/20220121133732.2397273-1-andre.przywara@arm.com/ Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2022-06-29mach-rockchip: make_fit_atf.py: support OP-TEE tee.bin v1 formatJerome Forissier1-8/+35
This commit adds support for the OP-TEE 'tee.bin' v1 format for Rockchip platforms. Since OP-TEE 3.8.0, tee.bin contains meta-data in a proprietary format in addition to the ELF data. They are essential information for proper initialization of the TEE core, such as the size of the memory region covered by the TEE or a compact representation of runtime relocation data when ASLR is enabled. With OP-TEE 3.8.0 onwards, 'tee.elf' MUST NOT be used and 'tee.bin' MUST be used instead. Ignoring this recommendation can lead to crashes as described in [3]. Link: [1] https://github.com/OP-TEE/optee_os/commit/5dd1570ac5b0f6563b1a9c074533a19107b8222d Link: [2] https://github.com/OP-TEE/optee_os/blob/3.17.0/scripts/gen_tee_bin.py#L275-L302 Link: [3] https://github.com/OP-TEE/optee_os/issues/4542 Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org> Tested-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
2022-06-29rockchip: board: change condition board_usb_init() in functionJohan Jonker1-1/+1
Change define condition in board_usb_init() function to allow rk3066/rk3188 to use the USB PHY driver. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-06-28spl: Move SPL_LDSCRIPT defaults to one placeTom Rini1-3/+0
We want to keep all of the default values for SPL_LDSCRIPT in the same place both for overall clarity as well as not polluting unrelated config files. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-23linker_lists: Rename sections to remove . prefixAndrew Scull1-2/+2
Rename the sections used to implement linker lists so they begin with '__u_boot_list' rather than '.u_boot_list'. The double underscore at the start is still distinct from the single underscore used by the symbol names. Having a '.' in the section names conflicts with clang's ASAN instrumentation which tries to add redzones between the linker list elements, causing expected accesses to fail. However, clang doesn't try to add redzones to user sections, which are names with all alphanumeric and underscore characters. Signed-off-by: Andrew Scull <ascull@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-06-06Convert CONFIG_SPL_PAD_TO et al to KconfigTom Rini6-18/+0
This converts the following to Kconfig: CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE CONFIG_TPL_PAD_TO CONFIG_TPL_MAX_SIZE Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the existing places. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-21arm: set cntfrq_el0 if CONFIG_COUNTER_FREQUENCY is validPeng Fan3-3/+3
Since COUNTER_FREQUENCY is obselete, so set cntfrq_el0 if CONFIG_COUNTER_FREQUENCY is valid Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
2022-04-18rockchip: fix boot_devices constantsJohan Jonker5-10/+10
The DT node name pattern in mmc-controller.yaml for mmc is "^mmc(@.*)?$". The Rockchip mmc nodes have been synced with Linux, so update the boot_devices constants as well. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18rockchip: rk3066: add Rikomagic MK808 boardJohan Jonker1-0/+9
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port, HDMI and a micro-SD card slot. It also includes on-board NAND and 1GB of SDRAM. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18rockchip: rk3066: add core supportJohan Jonker7-0/+196
Add the core architecture code for the rk3066. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18rockchip: tpl: use IS_ENABLED for timer_init() call conditionJohan Jonker1-2/+5
Not all Rockchip SoC models use the ARM arch timer. Call the function timer_init() only when CONFIG_SYS_ARCH_TIMER is available. Use the call condition IS_ENABLED to increase build coverage and make the code easier to read. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18rockchip: tpl: change call condition rockchip_stimer_init()Johan Jonker1-0/+2
The Rockchip SoCs rk3066/rk3188 have no CONFIG_ROCKCHIP_STIMER_BASE defined. Currently there's no exception in TPL. Make this more generic and compile the code inside the function rockchip_stimer_init() only when CONFIG_ROCKCHIP_STIMER_BASE is available. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18rockchip: spl: change call condition rockchip_stimer_init()Johan Jonker1-4/+4
The Rockchip SoCs rk3066/rk3188 have no CONFIG_ROCKCHIP_STIMER_BASE defined. Currently only rk3188 has an exception in SPL. Make this more generic and compile code inside the function rockchip_stimer_init() only when CONFIG_ROCKCHIP_STIMER_BASE is available. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-18rockchip: move ROCKCHIP_STIMER_BASE to KconfigJohan Jonker11-4/+43
Move ROCKCHIP_STIMER_BASE to Kconfig. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-04-04spl: mmc: extend spl_mmc_boot_mode() to take mmc argumentAndre Przywara1-1/+1
Platforms can overwrite the weak definition of spl_mmc_boot_mode() to determine where to load U-Boot proper from. For most of them this is a trivial decision based on Kconfig variables, but it might be desirable the probe the actual device to answer this question. Pass the pointer to the mmc struct to that function, so implementations can make use of that. Compile-tested for all users changed. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Ley Foon Tan <ley.foon.tan@inte.com> (for SoCFPGA) Acked-by: Lokesh Vutla <lokeshvutla@ti.com> (for OMAP and K3) Reviewed-by: Simon Glass <sjg@chromium.org>
2022-03-18rockchip: Set default LNX_KRNL_IMG_TEXT_OFFSET_BASE to SYS_TEXT_BASEAlper Nebi Yasak1-0/+3
U-Boot can be chainloaded from vendor firmware on ARM64 chromebooks from a GPT partition (roughly the same as in doc/chromium/chainload.rst), but an appropriate image header must be built-in to the U-Boot binary by enabling LINUX_KERNEL_IMAGE_HEADER. This header has a field for an image load offset from 2MiB alignment which must also be customized through LNX_KRNL_IMG_TEXT_OFFSET_BASE. Set it equal to SYS_TEXT_BASE by default for Rockchip boards, which happens to make this offset zero and works fine on chromebook_kevin both for chainloading and bare-metal use. Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2022-03-18rockchip: rk3399: Add support for chromebook_kevinMarty E. Plummer3-2/+15
Add support for Kevin, an RK3399-based convertible chromebook that is very similar to Bob. This patch is mostly based on existing support for Bob, with only minor changes for Kevin-specific things. Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV, so adjust it here in the dts as well. The rk3399-gru-kevin devicetree has an unknown event code reference which has to be defined, set it to the Linux counterpart. The new defconfig is copied from Bob with the diffconfig: DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin" DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb" VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400 VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600 +TARGET_CHROMEBOOK_KEVIN y With this Kevin can boot from SPI flash to a usable U-Boot prompt on the display with the keyboard working, but cannot boot into Linux for unknown reasons. eMMC starts in a working state but fails to re-init, microSD card works but at a lower-than-expected speed, USB works but causes a hang on de-init. There are known workarounds to solve eMMC and USB issues. Cc: Marty E. Plummer <hanetzer@startmail.com> Cc: Simon Glass <sjg@chromium.org> [Alper: commit message, resync config with Bob, update MAINTAINERS, add to Rockchip doc, add Kconfig help message, set regulator] Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2022-01-09Merge tag 'u-boot-amlogic-20220107' of ↵Tom Rini4-4/+35
https://source.denx.de/u-boot/custodians/u-boot-amlogic into next - disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs - meson64_android: add board specific env settings, in order to support VIM3/L for android - add changes to support VIM3/L android boot by using meson64_android.h config
2021-12-27Convert CONFIG_TPL_TEXT_BASE to KconfigTom Rini1-6/+0
This converts the following to Kconfig: CONFIG_TPL_TEXT_BASE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-24rockchip: boot_mode: fix fastboot commandJohn Keeping1-1/+1
The USB controller index must be separated from the type argument, otherwise the preboot command fails with the error: Error: Wrong USB controller index format Add the missing space to fix fastboot mode here. Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-12-24engicam: px30: Add Engicam PX30.Core C.TOUCH 2.0 10.1" OFJagan Teki1-0/+8
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam. C.TOUCH 2.0 is a general purpose carrier board with capacitive touch interface support. 10.1" OF is a capacitive touch 10.1" Open Frame panel solutions. PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged 10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame. Add support for it. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-12-24rockchip: rk3568: add arch_cpu_init()Nico Cheng1-3/+24
We configured the drive strength and security of EMMC in arch_cpu_init(). Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-12-24rockchip: Kconfig: Enable SPL support for rk3568Nico Cheng1-0/+2
Enable SPL support in Kconfig and add some related option in rk3568_common.h Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com> Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-11-17rk3399: Don't enable the debug UART if there is no driverSimon Glass1-16/+18
Some boards do not enable SPL_SERIAL so cannot use the debug UART. Add this condition to the code and drop use of the preprocessor while we are here. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
2021-10-05lib: optee: remove the duplicate CONFIG_OPTEEPatrick Delaunay1-1/+1
The configuration CONFIG_OPTEE is defined 2 times: 1- in lib/optee/Kconfig for support of OPTEE images loaded by bootm command 2- in drivers/tee/optee/Kconfig for support of OP-TEE driver. It is abnormal to have the same CONFIG define for 2 purpose; and it is difficult to managed correctly their dependencies. Moreover CONFIG_SPL_OPTEE is defined in common/spl/Kconfig to manage OPTEE image load in SPL. This definition causes an issue with the macro CONFIG_IS_ENABLED(OPTEE) to test the availability of the OP-TEE driver. This patch cleans the configuration dependency with: - CONFIG_OPTEE_IMAGE (renamed) => support of OP-TEE image in U-Boot - CONFIG_SPL_OPTEE_IMAGE (renamed) => support of OP-TEE image in SPL - CONFIG_OPTEE (same) => support of OP-TEE driver in U-Boot - CONFIG_OPTEE_LIB (new) => support of OP-TEE library After this patch, the macro have the correct behavior: - CONFIG_IS_ENABLED(OPTEE_IMAGE) => Load of OP-TEE image is supported - CONFIG_IS_ENABLED(OPTEE) => OP-TEE driver is supported Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-09-30WS cleanup: remove SPACE(s) followed by TABWolfgang Denk1-1/+1
Signed-off-by: Wolfgang Denk <wd@denx.de>
2021-09-25treewide: Use OF_REAL instead of !OF_PLATDATASimon Glass2-2/+2
Now that we have a 'positive' Kconfig option, use this instead of the negative one, which is harder to understand. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-25treewide: fdt: Move fdt_get_config_... to ofnode_conf_read...Simon Glass1-2/+2
The current API is outdated as it requires a devicetree pointer. Move these functions to use the ofnode API and update this globally. Add some tests while we are here. Correct the call in exynos_dsim_config_parse_dt() which is obviously wrong. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-17Remove including timestamp.h in version.hPali Rohár1-0/+4
Header file version.h does not use anything from timestamp.h. Including of timestamp.h has side effect which cause recompiling object file at every make run because timestamp.h changes at every run. So remove timestamp.h from version.h and include timestamp.h in files which needs it. This change reduce recompilation time of final U-Boot binary when U-Boot source files were not changed as less source files needs to be recompiled. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Add in lib/acpi/acpi_table.c and test/dm/acpi.c, rework a few others] Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-17Remove #include <version.h> from files which do not need itPali Rohár1-1/+0
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2021-09-04serial: Rename SERIAL_SUPPORT to SERIALSimon Glass8-20/+20
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-04mmc: Rename MMC_SUPPORT to MMCSimon Glass1-1/+1
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> [trini: Fixup some incorrect renames] Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31Convert CONFIG_SKIP_LOWLEVEL_INIT et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SKIP_LOWLEVEL_INIT CONFIG_SKIP_LOWLEVEL_INIT_ONLY In order to do this, we need to introduce SPL and TPL variants of these options so that we can clearly disable these options only in SPL in some cases, and both instances in other cases. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-12rockchip: px30: Add support for using SFCChris Morgan1-0/+64
This patch adds support for setting the correct pin configuration for the Rockchip Serial Flash Controller found on the PX30. Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11rk3399: boot_devices fix spinor node nameArtem Lapkin1-1/+1
Problem: board_spl_was_booted_from return wrong boot_devices[3] value /spi@ff1d0000 and same-as-spl dont work properly for SPINOR flash because arch/arm/mach-rockchip/spl-boot-order.c spl_node_to_boot_device need parse SPINOR flash node as UCLASS_SPI_FLASH spl-boot-order: same-as-spl > *** BOOT_SOURCE_ID 3 (2:emmc 3:spi 5:sd ... /spi@ff1d0000 > board_boot_order: could not map node @618 to a boot-device /sdhci@fe330000 > /mmc@fe320000 Solution: just change it to /spi@ff1d0000/flash@0 spl-boot-order: same-as-spl > *** BOOT_SOURCE_ID 3 (2:emmc 3:spi 5:sd ... /spi@ff1d0000/flash@0 > /sdhci@fe330000 > /mmc@fe320000 Signed-off-by: Artem Lapkin <art@khadas.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-07-28Rename DRIVERS_MISC_SUPPORT to DRIVERS_MISCSimon Glass2-6/+6
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-07-28Rename GPIO_SUPPORT to GPIOSimon Glass1-2/+2
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-06-18board: rockchip: Add rk3568 evb supportJoseph Chen1-0/+1
Add support for rk3568 evaluation board. Signed-off-by: Joseph Chen <chenjh@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-06-18rockchip: Add rk3568 architecture coreJoseph Chen7-0/+209
RK3568 is a high-performance and low power quad-core application processor designed for personal mobile internet device and AIoT equipments. Signed-off-by: Joseph Chen <chenjh@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-30 17:58:33 +0000