Merge branch 'master' of git://www.denx.de/git/u-boot-imx

28 files changed, 1672 insertions, 155 deletions

diff --git a/board/aristainetos/aristainetos.c b/board/aristainetos/aristainetos.c
index 67ac260055..8330bb64bd 100644
--- a/board/aristainetos/aristainetos.c
+++ b/board/aristainetos/aristainetos.c
@@ -321,8 +321,8 @@ static void enable_lvds(struct display_info_t const *dev)
 	/* enable backlight PWM 3 */
 	if (pwm_init(2, 0, 0))
 		goto error;
-	/* duty cycle 200ns, period: 3000ns */
-	if (pwm_config(2, 200, 3000))
+	/* duty cycle 500ns, period: 3000ns */
+	if (pwm_config(2, 500, 3000))
 		goto error;
 	if (pwm_enable(2))
 		goto error;
@@ -350,8 +350,8 @@ struct display_info_t const displays[] = {
 			.right_margin   = 88,
 			.upper_margin   = 10,
 			.lower_margin   = 10,
-			.hsync_len      = 25,
-			.vsync_len      = 1,
+			.hsync_len      = 80,
+			.vsync_len      = 25,
 			.sync           = 0,
 			.vmode          = FB_VMODE_NONINTERLACED
 		}
diff --git a/board/bachmann/ot1200/Makefile b/board/bachmann/ot1200/Makefile
index 1bd42e8321..9e50bfeb86 100644
--- a/board/bachmann/ot1200/Makefile
+++ b/board/bachmann/ot1200/Makefile
@@ -6,4 +6,8 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
+ifdef CONFIG_SPL_BUILD
+obj-y  := ot1200.o ot1200_spl.o
+else
 obj-y  := ot1200.o
+endif
diff --git a/board/bachmann/ot1200/mx6q_4x_mt41j128.cfg b/board/bachmann/ot1200/mx6q_4x_mt41j128.cfg
index bb6c60b4c3..c25f99dcfd 100644
--- a/board/bachmann/ot1200/mx6q_4x_mt41j128.cfg
+++ b/board/bachmann/ot1200/mx6q_4x_mt41j128.cfg
@@ -142,20 +142,6 @@ DATA 4 0x021b48b8 0x00000800
 DATA 4 0x021b001c 0x00000000
 DATA 4 0x021b0404 0x00011006
 
-/* set the default clock gate to save power */
-DATA 4 0x020c4068 0x00C03F3F
-DATA 4 0x020c406c 0x0030FC03
-DATA 4 0x020c4070 0x0FFFC000
-DATA 4 0x020c4074 0x3FF00000
-DATA 4 0x020c4078 0x00FFF300
-DATA 4 0x020c407c 0x0F0000C3
-DATA 4 0x020c4080 0x000003FF
-
-/* enable AXI cache for VDOA/VPU/IPU */
-DATA 4 0x020e0010 0xF00000CF
-/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
-DATA 4 0x020e0018 0x007F007F
-DATA 4 0x020e001c 0x007F007F
 
 /*
  * Setup CCM_CCOSR register as follows:
diff --git a/board/bachmann/ot1200/ot1200.c b/board/bachmann/ot1200/ot1200.c
index 93f3d65176..e434ed9b87 100644
--- a/board/bachmann/ot1200/ot1200.c
+++ b/board/bachmann/ot1200/ot1200.c
@@ -6,6 +6,7 @@
  */
 
 #include <common.h>
+#include <asm/io.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/iomux.h>
@@ -16,6 +17,7 @@
 #include <asm/imx-common/mxc_i2c.h>
 #include <asm/imx-common/boot_mode.h>
 #include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
 #include <mmc.h>
 #include <fsl_esdhc.h>
 #include <netdev.h>
@@ -46,7 +48,7 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
 {
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+	gd->ram_size = imx_ddr_size();
 
 	return 0;
 }
@@ -118,8 +120,35 @@ static void setup_iomux_features(void)
 		ARRAY_SIZE(feature_pads));
 }
 
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0x00C03F3F, &ccm->CCGR0);
+	writel(0x0030FC33, &ccm->CCGR1);
+	writel(0x0FFFC000, &ccm->CCGR2);
+	writel(0x3FF00000, &ccm->CCGR3);
+	writel(0x00FFF300, &ccm->CCGR4);
+	writel(0x0F0000C3, &ccm->CCGR5);
+	writel(0x000003FF, &ccm->CCGR6);
+}
+
+static void gpr_init(void)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	/* enable AXI cache for VDOA/VPU/IPU */
+	writel(0xF00000CF, &iomux->gpr[4]);
+	/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+	writel(0x007F007F, &iomux->gpr[6]);
+	writel(0x007F007F, &iomux->gpr[7]);
+}
+
 int board_early_init_f(void)
 {
+	ccgr_init();
+	gpr_init();
+
 	setup_iomux_uart();
 	setup_iomux_spi();
 	setup_iomux_features();
@@ -290,9 +319,6 @@ int board_init(void)
 
 	leds_on();
 
-	/* enable ecspi3 clocks */
-	enable_cspi_clock(1, 2);
-
 #ifdef CONFIG_CMD_SATA
 	setup_sata();
 #endif
diff --git a/board/bachmann/ot1200/ot1200_spl.c b/board/bachmann/ot1200/ot1200_spl.c
new file mode 100644
index 0000000000..9c77fd3330
--- /dev/null
+++ b/board/bachmann/ot1200/ot1200_spl.c
@@ -0,0 +1,162 @@
+/*
+ * Copyright (C) 2015, Bachmann electronic GmbH
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/arch/mx6-ddr.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Configure MX6Q/DUAL mmdc DDR io registers */
+static struct mx6dq_iomux_ddr_regs ot1200_ddr_ioregs = {
+	/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 48ohm */
+	.dram_sdclk_0   = 0x00000028,
+	.dram_sdclk_1   = 0x00000028,
+	.dram_cas       = 0x00000028,
+	.dram_ras       = 0x00000028,
+	.dram_reset     = 0x00000028,
+	/* SDCKE[0:1]: 100k pull-up */
+	.dram_sdcke0    = 0x00003000,
+	.dram_sdcke1    = 0x00003000,
+	/* SDBA2: pull-up disabled */
+	.dram_sdba2	    = 0x00000000,
+	/* SDODT[0:1]: 100k pull-up, 48 ohm */
+	.dram_sdodt0    = 0x00000028,
+	.dram_sdodt1    = 0x00000028,
+	/* SDQS[0:7]: Differential input, 48 ohm */
+	.dram_sdqs0     = 0x00000028,
+	.dram_sdqs1     = 0x00000028,
+	.dram_sdqs2     = 0x00000028,
+	.dram_sdqs3     = 0x00000028,
+	.dram_sdqs4     = 0x00000028,
+	.dram_sdqs5     = 0x00000028,
+	.dram_sdqs6     = 0x00000028,
+	.dram_sdqs7     = 0x00000028,
+	/* DQM[0:7]: Differential input, 48 ohm */
+	.dram_dqm0      = 0x00000028,
+	.dram_dqm1      = 0x00000028,
+	.dram_dqm2      = 0x00000028,
+	.dram_dqm3      = 0x00000028,
+	.dram_dqm4      = 0x00000028,
+	.dram_dqm5      = 0x00000028,
+	.dram_dqm6      = 0x00000028,
+	.dram_dqm7      = 0x00000028,
+};
+
+/* Configure MX6Q/DUAL mmdc GRP io registers */
+static struct mx6dq_iomux_grp_regs ot1200_grp_ioregs = {
+	/* DDR3 */
+	.grp_ddr_type    = 0x000c0000,
+	.grp_ddrmode_ctl = 0x00020000,
+	/* Disable DDR pullups */
+	.grp_ddrpke      = 0x00000000,
+	/* ADDR[00:16], SDBA[0:1]: 48 ohm */
+	.grp_addds       = 0x00000028,
+	/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 48 ohm */
+	.grp_ctlds       = 0x00000028,
+	/* DATA[00:63]: Differential input, 48 ohm */
+	.grp_ddrmode     = 0x00020000,
+	.grp_b0ds        = 0x00000028,
+	.grp_b1ds        = 0x00000028,
+	.grp_b2ds        = 0x00000028,
+	.grp_b3ds        = 0x00000028,
+	.grp_b4ds        = 0x00000028,
+	.grp_b5ds        = 0x00000028,
+	.grp_b6ds        = 0x00000028,
+	.grp_b7ds        = 0x00000028,
+};
+
+static struct mx6_ddr_sysinfo ot1200_ddr_sysinfo = {
+	/* Width of data bus: 0=16, 1=32, 2=64 */
+	.dsize      = 2,
+	/* config for full 4GB range so that get_mem_size() works */
+	.cs_density = 32, /* 32Gb per CS */
+	/* Single chip select */
+	.ncs        = 1,
+	.cs1_mirror = 0,	/* war 0 */
+	.rtt_wr     = 1,	/* DDR3_RTT_60_OHM - RTT_Wr = RZQ/4 */
+	.rtt_nom    = 1,	/* DDR3_RTT_60_OHM - RTT_Nom = RZQ/4 */
+	.walat      = 1,	/* Write additional latency */
+	.ralat      = 5,	/* Read additional latency */
+	.mif3_mode  = 3,	/* Command prediction working mode */
+	.bi_on      = 1,	/* Bank interleaving enabled */	/* war 1 */
+	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+};
+
+/* MT41K128M16JT-125 */
+static struct mx6_ddr3_cfg micron_2gib_1600 = {
+	.mem_speed = 1600,
+	.density   = 2,
+	.width     = 16,
+	.banks     = 8,
+	.rowaddr   = 14,
+	.coladdr   = 10,
+	.pagesz    = 2,
+	.trcd      = 1375,
+	.trcmin    = 4875,
+	.trasmin   = 3500,
+	.SRT       = 1,
+};
+
+static struct mx6_mmdc_calibration micron_2gib_1600_mmdc_calib = {
+	/* write leveling calibration determine */
+	.p0_mpwldectrl0 = 0x00260025,
+	.p0_mpwldectrl1 = 0x00270021,
+	.p1_mpwldectrl0 = 0x00180034,
+	.p1_mpwldectrl1 = 0x00180024,
+	/* Read DQS Gating calibration */
+	.p0_mpdgctrl0   = 0x04380344,
+	.p0_mpdgctrl1   = 0x0330032C,
+	.p1_mpdgctrl0   = 0x0338033C,
+	.p1_mpdgctrl1   = 0x032C0300,
+	/* Read Calibration: DQS delay relative to DQ read access */
+	.p0_mprddlctl   = 0x3C2E3238,
+	.p1_mprddlctl   = 0x3A2E303C,
+	/* Write Calibration: DQ/DM delay relative to DQS write access */
+	.p0_mpwrdlctl   = 0x36384036,
+	.p1_mpwrdlctl   = 0x442E4438,
+};
+
+static void ot1200_spl_dram_init(void)
+{
+	mx6dq_dram_iocfg(64, &ot1200_ddr_ioregs, &ot1200_grp_ioregs);
+	mx6_dram_cfg(&ot1200_ddr_sysinfo, &micron_2gib_1600_mmdc_calib,
+		     &micron_2gib_1600);
+}
+
+/*
+ * called from C runtime startup code (arch/arm/lib/crt0.S:_main)
+ * - we have a stack and a place to store GD, both in SRAM
+ * - no variable global data is available
+ */
+void board_init_f(ulong dummy)
+{
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	/* iomux and setup of i2c */
+	board_early_init_f();
+
+	/* setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* configure MMDC for SDRAM width/size and per-model calibration */
+	ot1200_spl_dram_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
+
+void reset_cpu(ulong addr)
+{
+}
diff --git a/board/barco/platinum/Kconfig b/board/barco/platinum/Kconfig
new file mode 100644
index 0000000000..8bbad24c0d
--- /dev/null
+++ b/board/barco/platinum/Kconfig
@@ -0,0 +1,37 @@
+if TARGET_PLATINUM_PICON
+
+config SYS_CPU
+	default "armv7"
+
+config SYS_VENDOR
+	default "barco"
+
+config SYS_SOC
+	default "mx6"
+
+config SYS_BOARD
+	default "platinum"
+
+config SYS_CONFIG_NAME
+	default "platinum_picon"
+
+endif
+
+if TARGET_PLATINUM_TITANIUM
+
+config SYS_CPU
+	default "armv7"
+
+config SYS_VENDOR
+	default "barco"
+
+config SYS_SOC
+	default "mx6"
+
+config SYS_BOARD
+	default "platinum"
+
+config SYS_CONFIG_NAME
+	default "platinum_titanium"
+
+endif
diff --git a/board/barco/platinum/MAINTAINERS b/board/barco/platinum/MAINTAINERS
new file mode 100644
index 0000000000..a22584b5e5
--- /dev/null
+++ b/board/barco/platinum/MAINTAINERS
@@ -0,0 +1,7 @@
+PLATINUM BOARD
+M:	Stefan Roese <sr@denx.de>
+S:	Maintained
+F:	board/barco/platinum/
+F:	include/configs/platinum.h
+F:	configs/platinum_picon_defconfig
+F:	configs/platinum_titanium_defconfig
diff --git a/board/barco/platinum/Makefile b/board/barco/platinum/Makefile
new file mode 100644
index 0000000000..abc941914a
--- /dev/null
+++ b/board/barco/platinum/Makefile
@@ -0,0 +1,14 @@
+#
+# Copyright (C) 2014, Barco (www.barco.com)
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y := platinum.o
+obj-$(CONFIG_TARGET_PLATINUM_PICON)     += platinum_picon.o
+obj-$(CONFIG_TARGET_PLATINUM_TITANIUM)  += platinum_titanium.o
+
+ifneq ($(CONFIG_SPL_BUILD),)
+obj-$(CONFIG_TARGET_PLATINUM_PICON) += spl_picon.o
+obj-$(CONFIG_TARGET_PLATINUM_TITANIUM) += spl_titanium.o
+endif
diff --git a/board/barco/platinum/platinum.c b/board/barco/platinum/platinum.c
new file mode 100644
index 0000000000..1485a4856f
--- /dev/null
+++ b/board/barco/platinum/platinum.c
@@ -0,0 +1,217 @@
+/*
+ * Copyright (C) 2014, Barco (www.barco.com)
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+
+#include "platinum.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__SD3_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_CMD__SD3_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT0__SD3_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT1__SD3_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT2__SD3_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT3__SD3_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT5__GPIO7_IO00	| MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+iomux_v3_cfg_t nfc_pads[] = {
+	MX6_PAD_NANDF_CLE__NAND_CLE		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_ALE__NAND_ALE		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_WP_B__NAND_WP_B		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_RB0__NAND_READY_B		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_CS0__NAND_CE0_B		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_CS1__NAND_CE1_B		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_CS2__NAND_CE2_B		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_CS3__NAND_CE3_B		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD4_CMD__NAND_RE_B		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD4_CLK__NAND_WE_B		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_D0__NAND_DATA00		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_D1__NAND_DATA01		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_D2__NAND_DATA02		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_D3__NAND_DATA03		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_D4__NAND_DATA04		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_D5__NAND_DATA05		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_D6__NAND_DATA06		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_D7__NAND_DATA07		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD4_DAT0__NAND_DQS		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{ USDHC3_BASE_ADDR },
+};
+
+void setup_gpmi_nand(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	/* config gpmi nand iomux */
+	imx_iomux_v3_setup_multiple_pads(nfc_pads, ARRAY_SIZE(nfc_pads));
+
+	/* config gpmi and bch clock to 100 MHz */
+	clrsetbits_le32(&mxc_ccm->cs2cdr,
+			MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
+			MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
+			MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
+			MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
+			MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
+			MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
+
+	/* enable gpmi and bch clock gating */
+	setbits_le32(&mxc_ccm->CCGR4,
+		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
+
+	/* enable apbh clock gating */
+	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+	return 0;
+}
+
+int board_ehci_hcd_init(int port)
+{
+	return 0;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+	if (cfg->esdhc_base == usdhc_cfg[0].esdhc_base) {
+		unsigned sd3_cd = IMX_GPIO_NR(7, 0);
+		gpio_direction_input(sd3_cd);
+		return !gpio_get_value(sd3_cd);
+	}
+
+	return 0;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+void board_init_gpio(void)
+{
+	platinum_init_gpio();
+}
+
+void board_init_gpmi_nand(void)
+{
+	setup_gpmi_nand();
+}
+
+void board_init_i2c(void)
+{
+	platinum_setup_i2c();
+}
+
+void board_init_spi(void)
+{
+	platinum_setup_spi();
+}
+
+void board_init_uart(void)
+{
+	platinum_setup_uart();
+}
+
+void board_init_usb(void)
+{
+	platinum_init_usb();
+}
+
+void board_init_finished(void)
+{
+	platinum_init_finished();
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	return platinum_phy_config(phydev);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	return cpu_eth_init(bis);
+}
+
+int board_early_init_f(void)
+{
+	board_init_uart();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	board_init_spi();
+
+	board_init_i2c();
+
+	board_init_gpmi_nand();
+
+	board_init_gpio();
+
+	board_init_usb();
+
+	board_init_finished();
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: " CONFIG_PLATINUM_BOARD "\n");
+	return 0;
+}
+
+static const struct boot_mode board_boot_modes[] = {
+	/* NAND */
+	{ "nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00) },
+	/* 4 bit bus width */
+	{ "mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00) },
+	{ "mmc1", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00) },
+	{ NULL, 0 },
+};
+
+int misc_init_r(void)
+{
+	add_board_boot_modes(board_boot_modes);
+
+	return 0;
+}
diff --git a/board/barco/platinum/platinum.h b/board/barco/platinum/platinum.h
new file mode 100644
index 0000000000..d3ea8bda73
--- /dev/null
+++ b/board/barco/platinum/platinum.h
@@ -0,0 +1,89 @@
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _PLATINUM_H_
+#define _PLATINUM_H_
+
+#include <miiphy.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+
+/* Defines */
+
+#define ECSPI1_PAD_CLK		(PAD_CTL_SRE_SLOW | PAD_CTL_PUS_100K_DOWN | \
+				 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | \
+				 PAD_CTL_HYS)
+#define ECSPI2_PAD_CLK		(PAD_CTL_SRE_FAST | PAD_CTL_PUS_100K_DOWN | \
+				 PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+				 PAD_CTL_HYS)
+#define ECSPI_PAD_MOSI		(PAD_CTL_SRE_SLOW | PAD_CTL_PUS_100K_DOWN | \
+				 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_120ohm | \
+				 PAD_CTL_HYS)
+#define ECSPI_PAD_MISO		(PAD_CTL_SRE_FAST | PAD_CTL_PUS_100K_DOWN | \
+				 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | \
+				 PAD_CTL_HYS)
+#define ECSPI_PAD_SS		(PAD_CTL_SRE_SLOW | PAD_CTL_PUS_100K_UP | \
+				 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_120ohm | \
+				 PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL		(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+				 PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL		(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+				 PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+				 PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+#define I2C_PAD_CTRL_SCL	(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \
+				 PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \
+				 PAD_CTL_ODE | PAD_CTL_SRE_SLOW)
+
+#define UART_PAD_CTRL		(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+				 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | \
+				 PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL		(PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW | \
+				PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | \
+				PAD_CTL_HYS)
+
+
+#define PC			MUX_PAD_CTRL(I2C_PAD_CTRL)
+#define PC_SCL			MUX_PAD_CTRL(I2C_PAD_CTRL_SCL)
+
+/* Prototypes */
+
+int platinum_setup_enet(void);
+int platinum_setup_i2c(void);
+int platinum_setup_spi(void);
+int platinum_setup_uart(void);
+int platinum_phy_config(struct phy_device *phydev);
+int platinum_init_gpio(void);
+int platinum_init_usb(void);
+int platinum_init_finished(void);
+
+static inline void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0x00C03F3F, &ccm->CCGR0);
+	writel(0x0030FC03, &ccm->CCGR1);
+	writel(0x0FFFC000, &ccm->CCGR2);
+	writel(0x3FF00000, &ccm->CCGR3);
+	writel(0xFFFFF300, &ccm->CCGR4);	/* enable NAND/GPMI/BCH clks */
+	writel(0x0F0000C3, &ccm->CCGR5);
+	writel(0x000003FF, &ccm->CCGR6);
+}
+
+static inline void gpr_init(void)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	/* enable AXI cache for VDOA/VPU/IPU */
+	writel(0xF00000CF, &iomux->gpr[4]);
+	/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+	writel(0x007F007F, &iomux->gpr[6]);
+	writel(0x007F007F, &iomux->gpr[7]);
+}
+
+#endif /* _PLATINUM_H_ */
diff --git a/board/barco/platinum/platinum_picon.c b/board/barco/platinum/platinum_picon.c
new file mode 100644
index 0000000000..b2eab766c5
--- /dev/null
+++ b/board/barco/platinum/platinum_picon.c
@@ -0,0 +1,244 @@
+/*
+ * Copyright (C) 2014, Barco (www.barco.com)
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <i2c.h>
+#include <miiphy.h>
+
+#include "platinum.h"
+
+#define GPIO_IP_NCONFIG		IMX_GPIO_NR(5, 18)
+#define GPIO_HK_NCONFIG		IMX_GPIO_NR(7, 13)
+#define GPIO_LS_NCONFIG		IMX_GPIO_NR(5, 19)
+
+#define GPIO_I2C0_SEL0		IMX_GPIO_NR(5,  2)
+#define GPIO_I2C0_SEL1		IMX_GPIO_NR(1, 11)
+#define GPIO_I2C0_ENBN		IMX_GPIO_NR(1, 13)
+
+#define GPIO_I2C2_SEL0		IMX_GPIO_NR(1, 17)
+#define GPIO_I2C2_SEL1		IMX_GPIO_NR(1, 20)
+#define GPIO_I2C2_ENBN		IMX_GPIO_NR(1, 14)
+
+#define GPIO_USB_RESET		IMX_GPIO_NR(1,  5)
+
+iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_EIM_D16__ECSPI1_SCLK		| MUX_PAD_CTRL(ECSPI1_PAD_CLK),
+	MX6_PAD_EIM_D17__ECSPI1_MISO		| MUX_PAD_CTRL(ECSPI_PAD_MISO),
+	MX6_PAD_EIM_D18__ECSPI1_MOSI		| MUX_PAD_CTRL(ECSPI_PAD_MOSI),
+	MX6_PAD_CSI0_DAT7__ECSPI1_SS0		| MUX_PAD_CTRL(ECSPI_PAD_SS),
+	MX6_PAD_EIM_D24__ECSPI1_SS2		| MUX_PAD_CTRL(ECSPI_PAD_SS),
+	MX6_PAD_EIM_D25__ECSPI1_SS3		| MUX_PAD_CTRL(ECSPI_PAD_SS),
+};
+
+iomux_v3_cfg_t const ecspi2_pads[] = {
+	MX6_PAD_EIM_CS0__ECSPI2_SCLK		| MUX_PAD_CTRL(ECSPI2_PAD_CLK),
+	MX6_PAD_EIM_OE__ECSPI2_MISO		| MUX_PAD_CTRL(ECSPI_PAD_MISO),
+	MX6_PAD_EIM_CS1__ECSPI2_MOSI		| MUX_PAD_CTRL(ECSPI_PAD_MOSI),
+	MX6_PAD_EIM_RW__ECSPI2_SS0		| MUX_PAD_CTRL(ECSPI_PAD_SS),
+	MX6_PAD_EIM_LBA__ECSPI2_SS1		| MUX_PAD_CTRL(ECSPI_PAD_SS),
+};
+
+iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_CRS_DV__ENET_RX_EN		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_GPIO_16__ENET_REF_CLK		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RX_ER__ENET_RX_ER		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RXD0__ENET_RX_DATA0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RXD1__ENET_RX_DATA1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TX_EN__ENET_TX_EN		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TXD0__ENET_TX_DATA0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TXD1__ENET_TX_DATA1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+/* PHY nRESET */
+iomux_v3_cfg_t const phy_reset_pad = {
+	MX6_PAD_SD1_DAT2__GPIO1_IO19		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart4_pads[] = {
+	MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT16__UART4_RTS_B   | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT17__UART4_CTS_B   | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart5_pads[] = {
+	MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT15__UART5_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT18__UART5_RTS_B   | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT19__UART5_CTS_B   | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const i2c0_mux_pads[] = {
+	MX6_PAD_EIM_A25__GPIO5_IO02		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD2_CMD__GPIO1_IO11		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD2_DAT2__GPIO1_IO13		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const i2c2_mux_pads[] = {
+	MX6_PAD_SD1_DAT1__GPIO1_IO17		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD1_CLK__GPIO1_IO20		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__GPIO1_IO14		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+struct i2c_pads_info i2c_pad_info0 = {
+	.scl = {
+		.i2c_mode  = MX6_PAD_CSI0_DAT9__I2C1_SCL	| PC_SCL,
+		.gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27	| PC_SCL,
+		.gp = IMX_GPIO_NR(5, 27)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA		| PC,
+		.gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26	| PC,
+		.gp = IMX_GPIO_NR(5, 26)
+	 }
+};
+
+struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL		| PC_SCL,
+		.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03		| PC_SCL,
+		.gp = IMX_GPIO_NR(1, 3)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA		| PC,
+		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06		| PC,
+		.gp = IMX_GPIO_NR(1, 6)
+	 }
+};
+
+/*
+ * This enet related pin-muxing and GPIO handling is done
+ * in SPL U-Boot. For early initialization. And to give the
+ * PHY some time to come out of reset before the U-Boot
+ * ethernet driver tries to access its registers via MDIO.
+ */
+int platinum_setup_enet(void)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	unsigned phy_reset = IMX_GPIO_NR(1, 19);
+
+	/* First configure PHY reset GPIO pin */
+	imx_iomux_v3_setup_pad(phy_reset_pad);
+
+	/* Reconfigure enet muxing while PHY is in reset */
+	gpio_direction_output(phy_reset, 0);
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+	mdelay(10);
+	gpio_set_value(phy_reset, 1);
+	udelay(100);
+
+	/* set GPIO_16 as ENET_REF_CLK_OUT */
+	setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
+
+	return enable_fec_anatop_clock(ENET_50MHZ);
+}
+
+int platinum_setup_i2c(void)
+{
+	imx_iomux_v3_setup_multiple_pads(i2c0_mux_pads,
+					 ARRAY_SIZE(i2c0_mux_pads));
+	imx_iomux_v3_setup_multiple_pads(i2c2_mux_pads,
+					 ARRAY_SIZE(i2c2_mux_pads));
+
+	mdelay(10);
+
+	/* Disable i2c mux 0 */
+	gpio_direction_output(GPIO_I2C0_SEL0, 0);
+	gpio_direction_output(GPIO_I2C0_SEL1, 0);
+	gpio_direction_output(GPIO_I2C0_ENBN, 1);
+
+	/* Disable i2c mux 1 */
+	gpio_direction_output(GPIO_I2C2_SEL0, 0);
+	gpio_direction_output(GPIO_I2C2_SEL1, 0);
+	gpio_direction_output(GPIO_I2C2_ENBN, 1);
+
+	udelay(10);
+
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+
+	/* Disable all leds */
+	i2c_set_bus_num(0);
+	i2c_reg_write(0x60, 0x05, 0x55);
+
+	return 0;
+}
+
+int platinum_setup_spi(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+	imx_iomux_v3_setup_multiple_pads(ecspi2_pads, ARRAY_SIZE(ecspi2_pads));
+
+	return 0;
+}
+
+int platinum_setup_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+	imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+
+	return 0;
+}
+
+int platinum_phy_config(struct phy_device *phydev)
+{
+	/* Use generic infrastructure, no specific setup */
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+int platinum_init_gpio(void)
+{
+	/* Reset FPGA's */
+	gpio_direction_output(GPIO_IP_NCONFIG, 0);
+	gpio_direction_output(GPIO_HK_NCONFIG, 0);
+	gpio_direction_output(GPIO_LS_NCONFIG, 0);
+	udelay(3);
+	gpio_set_value(GPIO_IP_NCONFIG, 1);
+	gpio_set_value(GPIO_HK_NCONFIG, 1);
+	gpio_set_value(GPIO_LS_NCONFIG, 1);
+
+	/* no dmd configuration yet */
+
+	return 0;
+}
+
+int platinum_init_usb(void)
+{
+	/* Reset usb hub */
+	gpio_direction_output(GPIO_USB_RESET, 0);
+	udelay(100);
+	gpio_set_value(GPIO_USB_RESET, 1);
+
+	return 0;
+}
+
+int platinum_init_finished(void)
+{
+	/* Enable led 0 */
+	i2c_set_bus_num(0);
+	i2c_reg_write(0x60, 0x05, 0x54);
+
+	return 0;
+}
diff --git a/board/barco/platinum/platinum_titanium.c b/board/barco/platinum/platinum_titanium.c
new file mode 100644
index 0000000000..73a955f019
--- /dev/null
+++ b/board/barco/platinum/platinum_titanium.c
@@ -0,0 +1,209 @@
+/*
+ * Copyright (C) 2014, Barco (www.barco.com)
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <miiphy.h>
+#include <micrel.h>
+
+#include "platinum.h"
+
+iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_EIM_D16__ECSPI1_SCLK		| MUX_PAD_CTRL(ECSPI1_PAD_CLK),
+	MX6_PAD_EIM_D17__ECSPI1_MISO		| MUX_PAD_CTRL(ECSPI_PAD_MISO),
+	MX6_PAD_EIM_D18__ECSPI1_MOSI		| MUX_PAD_CTRL(ECSPI_PAD_MOSI),
+	MX6_PAD_CSI0_DAT7__ECSPI1_SS0		| MUX_PAD_CTRL(ECSPI_PAD_SS),
+	/* non mounted spi nor flash for booting */
+	MX6_PAD_EIM_D19__ECSPI1_SS1		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D24__ECSPI1_SS2		| MUX_PAD_CTRL(ECSPI_PAD_SS),
+	MX6_PAD_EIM_D25__ECSPI1_SS3		| MUX_PAD_CTRL(ECSPI_PAD_SS),
+};
+
+iomux_v3_cfg_t const ecspi2_pads[] = {
+	MX6_PAD_EIM_CS0__ECSPI2_SCLK		| MUX_PAD_CTRL(ECSPI2_PAD_CLK),
+	MX6_PAD_EIM_OE__ECSPI2_MISO		| MUX_PAD_CTRL(ECSPI_PAD_MISO),
+	MX6_PAD_EIM_CS1__ECSPI2_MOSI		| MUX_PAD_CTRL(ECSPI_PAD_MOSI),
+	MX6_PAD_EIM_RW__ECSPI2_SS0		| MUX_PAD_CTRL(ECSPI_PAD_SS),
+};
+
+iomux_v3_cfg_t const enet_pads1[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	/* pin 35 - 1 (PHY_AD2) on reset */
+	MX6_PAD_RGMII_RXC__GPIO6_IO30		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 32 - 1 - (MODE0) all */
+	MX6_PAD_RGMII_RD0__GPIO6_IO25		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 31 - 1 - (MODE1) all */
+	MX6_PAD_RGMII_RD1__GPIO6_IO27		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 28 - 1 - (MODE2) all */
+	MX6_PAD_RGMII_RD2__GPIO6_IO28		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 27 - 1 - (MODE3) all */
+	MX6_PAD_RGMII_RD3__GPIO6_IO29		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */
+	MX6_PAD_RGMII_RX_CTL__GPIO6_IO24	| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* pin 42 PHY nRST */
+	MX6_PAD_EIM_D23__GPIO3_IO23		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const enet_pads2[] = {
+	MX6_PAD_RGMII_RXC__RGMII_RXC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__RGMII_RD1		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__RGMII_RD2		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart2_pads[] = {
+	MX6_PAD_EIM_D26__UART2_TX_DATA   | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D27__UART2_RX_DATA   | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D28__UART2_DTE_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D29__UART2_RTS_B     | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart4_pads[] = {
+	MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT16__UART4_RTS_B   | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT17__UART4_CTS_B   | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+struct i2c_pads_info i2c_pad_info0 = {
+	.scl = {
+		.i2c_mode  = MX6_PAD_CSI0_DAT9__I2C1_SCL	| PC_SCL,
+		.gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27	| PC_SCL,
+		.gp = IMX_GPIO_NR(5, 27)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA		| PC,
+		.gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26	| PC,
+		.gp = IMX_GPIO_NR(5, 26)
+	 }
+};
+
+struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL		| PC_SCL,
+		.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03		| PC_SCL,
+		.gp = IMX_GPIO_NR(1, 3)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA		| PC,
+		.gpio_mode = MX6_PAD_GPIO_16__GPIO7_IO11	| PC,
+		.gp = IMX_GPIO_NR(7, 11)
+	 }
+};
+
+/*
+ * This enet related pin-muxing and GPIO handling is done
+ * in SPL U-Boot. For early initialization. And to give the
+ * PHY some time to come out of reset before the U-Boot
+ * ethernet driver tries to access its registers via MDIO.
+ */
+int platinum_setup_enet(void)
+{
+	gpio_direction_output(IMX_GPIO_NR(3, 23), 0);
+	gpio_direction_output(IMX_GPIO_NR(6, 30), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 25), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 27), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 28), 1);
+	gpio_direction_output(IMX_GPIO_NR(6, 29), 1);
+	imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1));
+	gpio_direction_output(IMX_GPIO_NR(6, 24), 1);
+
+	/* Need delay 10ms according to KSZ9021 spec */
+	mdelay(10);
+	gpio_set_value(IMX_GPIO_NR(3, 23), 1);
+	udelay(100);
+
+	imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2));
+
+	return 0;
+}
+
+int platinum_setup_i2c(void)
+{
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+
+	return 0;
+}
+
+int platinum_setup_spi(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+	imx_iomux_v3_setup_multiple_pads(ecspi2_pads, ARRAY_SIZE(ecspi2_pads));
+
+	return 0;
+}
+
+int platinum_setup_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+	imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+
+	return 0;
+}
+
+int platinum_phy_config(struct phy_device *phydev)
+{
+	/* min rx data delay */
+	ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
+				   0x0);
+	/* min tx data delay */
+	ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
+				   0x0);
+	/* max rx/tx clock delay, min rx/tx control */
+	ksz9021_phy_extended_write(phydev, MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
+				   0xf0f0);
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+int platinum_init_gpio(void)
+{
+	/* Default GPIO's */
+	/* Toggle CONFIG_n to reset fpga on every boot */
+	gpio_direction_output(IMX_GPIO_NR(5, 18), 0);
+	/* Need delay >=2uS */
+	udelay(3);
+	gpio_set_value(IMX_GPIO_NR(5, 18), 1);
+
+	/* Default pin 1,15 high - DLP_FLASH_WPZ */
+	gpio_direction_output(IMX_GPIO_NR(1, 15), 1);
+
+	return 0;
+}
+
+int platinum_init_usb(void)
+{
+	return 0;
+}
+
+int platinum_init_finished(void)
+{
+	return 0;
+}
diff --git a/board/barco/platinum/spl_picon.c b/board/barco/platinum/spl_picon.c
new file mode 100644
index 0000000000..f421c2108c
--- /dev/null
+++ b/board/barco/platinum/spl_picon.c
@@ -0,0 +1,182 @@
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * Based on: gw_ventana_spl.c which is:
+ * Copyright (C) 2014 Gateworks Corporation
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <spl.h>
+
+#include "platinum.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#undef RTT_NOM_120OHM	/* use 120ohm Rtt_nom vs 60ohm (lower power) */
+
+/* Configure MX6Q/DUAL mmdc DDR io registers */
+struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
+	/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
+	.dram_sdclk_0 = 0x00020030,
+	.dram_sdclk_1 = 0x00020030,
+	.dram_cas = 0x00020030,
+	.dram_ras = 0x00020030,
+	.dram_reset = 0x00020030,
+	/* SDCKE[0:1]: 100k pull-up */
+	.dram_sdcke0 = 0x00003000,
+	.dram_sdcke1 = 0x00003000,
+	/* SDBA2: pull-up disabled */
+	.dram_sdba2 = 0x00000000,
+	/* SDODT[0:1]: 100k pull-up, 40 ohm */
+	.dram_sdodt0 = 0x00003030,
+	.dram_sdodt1 = 0x00003030,
+	/* SDQS[0:7]: Differential input, 40 ohm */
+	.dram_sdqs0 = 0x00000030,
+	.dram_sdqs1 = 0x00000030,
+	.dram_sdqs2 = 0x00000030,
+	.dram_sdqs3 = 0x00000030,
+	.dram_sdqs4 = 0x00000030,
+	.dram_sdqs5 = 0x00000030,
+	.dram_sdqs6 = 0x00000030,
+	.dram_sdqs7 = 0x00000030,
+	/* DQM[0:7]: Differential input, 40 ohm */
+	.dram_dqm0 = 0x00020030,
+	.dram_dqm1 = 0x00020030,
+	.dram_dqm2 = 0x00020030,
+	.dram_dqm3 = 0x00020030,
+	.dram_dqm4 = 0x00020030,
+	.dram_dqm5 = 0x00020030,
+	.dram_dqm6 = 0x00020030,
+	.dram_dqm7 = 0x00020030,
+};
+
+/* Configure MX6Q/DUAL mmdc GRP io registers */
+struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
+	/* DDR3 */
+	.grp_ddr_type = 0x000c0000,
+	.grp_ddrmode_ctl = 0x00020000,
+	/* disable DDR pullups */
+	.grp_ddrpke = 0x00000000,
+	/* ADDR[00:16], SDBA[0:1]: 40 ohm */
+	.grp_addds = 0x00000030,
+	/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
+	.grp_ctlds = 0x00000030,
+	/* DATA[00:63]: Differential input, 40 ohm */
+	.grp_ddrmode = 0x00020000,
+	.grp_b0ds = 0x00000030,
+	.grp_b1ds = 0x00000030,
+	.grp_b2ds = 0x00000030,
+	.grp_b3ds = 0x00000030,
+	.grp_b4ds = 0x00000030,
+	.grp_b5ds = 0x00000030,
+	.grp_b6ds = 0x00000030,
+	.grp_b7ds = 0x00000030,
+};
+
+/* MT41K256M16HA-125 */
+static struct mx6_ddr3_cfg mt41k256m16ha_125 = {
+	.mem_speed = 1600,
+	.density = 4,		/* 4Gbit */
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 15,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+/*
+ * Values from running the Freescale DDR stress tool via USB
+ */
+static struct mx6_mmdc_calibration mx6dq_mmdc_calib = {
+	/* write leveling calibration determine */
+	.p0_mpwldectrl0 = 0x0044004E,
+	.p0_mpwldectrl1 = 0x001F0023,
+	/* Read DQS Gating calibration */
+	.p0_mpdgctrl0 = 0x02480248,
+	.p0_mpdgctrl1 = 0x0210021C,
+	/* Read Calibration: DQS delay relative to DQ read access */
+	.p0_mprddlctl = 0x42444444,
+	/* Write Calibration: DQ/DM delay relative to DQS write access */
+	.p0_mpwrdlctl = 0x36322C32,
+};
+
+static void spl_dram_init(int width)
+{
+	struct mx6_ddr3_cfg *mem = &mt41k256m16ha_125;
+	struct mx6_ddr_sysinfo sysinfo = {
+		/* width of data bus:0=16,1=32,2=64 */
+		.dsize = width / 32,
+		/* config for full 4GB range so that get_mem_size() works */
+		.cs_density = 32, /* 32Gb per CS */
+		/* single chip select */
+		.ncs = 1,
+		.cs1_mirror = 1,
+		.rtt_wr = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Wr = RZQ/4 */
+#ifdef RTT_NOM_120OHM
+		.rtt_nom = 2 /*DDR3_RTT_120_OHM*/,	/* RTT_Nom = RZQ/2 */
+#else
+		.rtt_nom = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Nom = RZQ/4 */
+#endif
+		.walat = 0,	/* Write additional latency */
+		.ralat = 5,	/* Read additional latency */
+		.mif3_mode = 3,	/* Command prediction working mode */
+		.bi_on = 1,	/* Bank interleaving enabled */
+		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+	};
+
+	mx6sdl_dram_iocfg(width, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
+	mx6_dram_cfg(&sysinfo, &mx6dq_mmdc_calib, mem);
+}
+
+/*
+ * Called from C runtime startup code (arch/arm/lib/crt0.S:_main)
+ * - we have a stack and a place to store GD, both in SRAM
+ * - no variable global data is available
+ */
+void board_init_f(ulong dummy)
+{
+	/* Setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+	gpr_init();
+
+	/* UART iomux */
+	board_early_init_f();
+
+	/* Setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* Init DDR with 32bit width */
+	spl_dram_init(32);
+
+	/* Clear the BSS */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/*
+	 * Setup enet related MUXing early to give the PHY
+	 * some time to wake-up from reset
+	 */
+	platinum_setup_enet();
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
diff --git a/board/barco/platinum/spl_titanium.c b/board/barco/platinum/spl_titanium.c
new file mode 100644
index 0000000000..26fe26ba2b
--- /dev/null
+++ b/board/barco/platinum/spl_titanium.c
@@ -0,0 +1,185 @@
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * Based on: gw_ventana_spl.c which is:
+ * Copyright (C) 2014 Gateworks Corporation
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <spl.h>
+
+#include "platinum.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#undef RTT_NOM_120OHM	/* use 120ohm Rtt_nom vs 60ohm (lower power) */
+
+/* Configure MX6Q/DUAL mmdc DDR io registers */
+struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = {
+	/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
+	.dram_sdclk_0 = 0x00020030,
+	.dram_sdclk_1 = 0x00020030,
+	.dram_cas = 0x00020030,
+	.dram_ras = 0x00020030,
+	.dram_reset = 0x00020030,
+	/* SDCKE[0:1]: 100k pull-up */
+	.dram_sdcke0 = 0x00003000,
+	.dram_sdcke1 = 0x00003000,
+	/* SDBA2: pull-up disabled */
+	.dram_sdba2 = 0x00000000,
+	/* SDODT[0:1]: 100k pull-up, 40 ohm */
+	.dram_sdodt0 = 0x00003030,
+	.dram_sdodt1 = 0x00003030,
+	/* SDQS[0:7]: Differential input, 40 ohm */
+	.dram_sdqs0 = 0x00000030,
+	.dram_sdqs1 = 0x00000030,
+	.dram_sdqs2 = 0x00000030,
+	.dram_sdqs3 = 0x00000030,
+	.dram_sdqs4 = 0x00000030,
+	.dram_sdqs5 = 0x00000030,
+	.dram_sdqs6 = 0x00000030,
+	.dram_sdqs7 = 0x00000030,
+	/* DQM[0:7]: Differential input, 40 ohm */
+	.dram_dqm0 = 0x00020030,
+	.dram_dqm1 = 0x00020030,
+	.dram_dqm2 = 0x00020030,
+	.dram_dqm3 = 0x00020030,
+	.dram_dqm4 = 0x00020030,
+	.dram_dqm5 = 0x00020030,
+	.dram_dqm6 = 0x00020030,
+	.dram_dqm7 = 0x00020030,
+};
+
+/* Configure MX6Q/DUAL mmdc GRP io registers */
+struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = {
+	/* DDR3 */
+	.grp_ddr_type = 0x000c0000,
+	.grp_ddrmode_ctl = 0x00020000,
+	/* disable DDR pullups */
+	.grp_ddrpke = 0x00000000,
+	/* ADDR[00:16], SDBA[0:1]: 40 ohm */
+	.grp_addds = 0x00000030,
+	/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
+	.grp_ctlds = 0x00000030,
+	/* DATA[00:63]: Differential input, 40 ohm */
+	.grp_ddrmode = 0x00020000,
+	.grp_b0ds = 0x00000030,
+	.grp_b1ds = 0x00000030,
+	.grp_b2ds = 0x00000030,
+	.grp_b3ds = 0x00000030,
+	.grp_b4ds = 0x00000030,
+	.grp_b5ds = 0x00000030,
+	.grp_b6ds = 0x00000030,
+	.grp_b7ds = 0x00000030,
+};
+
+/* MT41J128M16JT-125 */
+static struct mx6_ddr3_cfg mt41j128m16jt_125 = {
+	.mem_speed = 1600,
+	.density = 2,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static struct mx6_mmdc_calibration mx6dq_mmdc_calib = {
+	/* Write leveling calibration determine */
+	.p0_mpwldectrl0 = 0x001f001f,
+	.p0_mpwldectrl1 = 0x001f001f,
+	.p1_mpwldectrl0 = 0x00440044,
+	.p1_mpwldectrl1 = 0x00440044,
+	/* Read DQS Gating calibration */
+	.p0_mpdgctrl0 = 0x434b0350,
+	.p0_mpdgctrl1 = 0x034c0359,
+	.p1_mpdgctrl0 = 0x434b0350,
+	.p1_mpdgctrl1 = 0x03650348,
+	/* Read Calibration: DQS delay relative to DQ read access */
+	.p0_mprddlctl = 0x4436383b,
+	.p1_mprddlctl = 0x39393341,
+	/* Write Calibration: DQ/DM delay relative to DQS write access */
+	.p0_mpwrdlctl = 0x35373933,
+	.p1_mpwrdlctl = 0x48254a36,
+};
+
+static void spl_dram_init(int width)
+{
+	struct mx6_ddr3_cfg *mem = &mt41j128m16jt_125;
+	struct mx6_ddr_sysinfo sysinfo = {
+		/* width of data bus:0=16,1=32,2=64 */
+		.dsize = width / 32,
+		/* config for full 4GB range so that get_mem_size() works */
+		.cs_density = 32, /* 32Gb per CS */
+		/* single chip select */
+		.ncs = 1,
+		.cs1_mirror = 1,
+		.rtt_wr = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Wr = RZQ/4 */
+#ifdef RTT_NOM_120OHM
+		.rtt_nom = 2 /*DDR3_RTT_120_OHM*/,	/* RTT_Nom = RZQ/2 */
+#else
+		.rtt_nom = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Nom = RZQ/4 */
+#endif
+		.walat = 0,	/* Write additional latency */
+		.ralat = 5,	/* Read additional latency */
+		.mif3_mode = 3,	/* Command prediction working mode */
+		.bi_on = 1,	/* Bank interleaving enabled */
+		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+	};
+
+	mx6dq_dram_iocfg(width, &mx6dq_ddr_ioregs, &mx6dq_grp_ioregs);
+	mx6_dram_cfg(&sysinfo, &mx6dq_mmdc_calib, mem);
+}
+
+/*
+ * Called from C runtime startup code (arch/arm/lib/crt0.S:_main)
+ * - we have a stack and a place to store GD, both in SRAM
+ * - no variable global data is available
+ */
+void board_init_f(ulong dummy)
+{
+	/* Setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+	gpr_init();
+
+	/* UART iomux */
+	board_early_init_f();
+
+	/* Setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* Init DDR with 32bit width */
+	spl_dram_init(32);
+
+	/* Clear the BSS */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/*
+	 * Setup enet related MUXing early to give the PHY
+	 * some time to wake-up from reset
+	 */
+	platinum_setup_enet();
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
index 84e36439fa..ae6945ba9c 100644
--- a/board/compulab/cm_fx6/cm_fx6.c
+++ b/board/compulab/cm_fx6/cm_fx6.c
@@ -15,19 +15,86 @@
 #include <netdev.h>
 #include <fdt_support.h>
 #include <sata.h>
+#include <splash.h>
 #include <asm/arch/crm_regs.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/arch/iomux.h>
+#include <asm/arch/mxc_hdmi.h>
 #include <asm/imx-common/mxc_i2c.h>
 #include <asm/imx-common/sata.h>
+#include <asm/imx-common/video.h>
 #include <asm/io.h>
 #include <asm/gpio.h>
 #include <dm/platform_data/serial_mxc.h>
 #include "common.h"
 #include "../common/eeprom.h"
+#include "../common/common.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#ifdef CONFIG_SPLASH_SCREEN
+static struct splash_location cm_fx6_splash_locations[] = {
+	{
+		.name = "sf",
+		.storage = SPLASH_STORAGE_SF,
+		.offset = 0x100000,
+	},
+};
+
+int splash_screen_prepare(void)
+{
+	return splash_source_load(cm_fx6_splash_locations,
+				  ARRAY_SIZE(cm_fx6_splash_locations));
+}
+#endif
+
+#ifdef CONFIG_IMX_HDMI
+static void cm_fx6_enable_hdmi(struct display_info_t const *dev)
+{
+	imx_enable_hdmi_phy();
+}
+
+struct display_info_t const displays[] = {
+	{
+		.bus	= -1,
+		.addr	= 0,
+		.pixfmt	= IPU_PIX_FMT_RGB24,
+		.detect	= detect_hdmi,
+		.enable	= cm_fx6_enable_hdmi,
+		.mode	= {
+			.name           = "HDMI",
+			.refresh        = 60,
+			.xres           = 1024,
+			.yres           = 768,
+			.pixclock       = 40385,
+			.left_margin    = 220,
+			.right_margin   = 40,
+			.upper_margin   = 21,
+			.lower_margin   = 7,
+			.hsync_len      = 60,
+			.vsync_len      = 10,
+			.sync           = FB_SYNC_EXT,
+			.vmode          = FB_VMODE_NONINTERLACED,
+		}
+	},
+};
+size_t display_count = ARRAY_SIZE(displays);
+
+static void cm_fx6_setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	int reg;
+
+	enable_ipu_clock();
+	imx_setup_hdmi();
+	reg = __raw_readl(&mxc_ccm->CCGR3);
+	reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_MASK;
+	writel(reg, &mxc_ccm->CCGR3);
+}
+#else
+static inline void cm_fx6_setup_display(void) {}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
 #ifdef CONFIG_DWC_AHSATA
 static int cm_fx6_issd_gpios[] = {
 	/* The order of the GPIOs in the array is important! */
@@ -345,32 +412,36 @@ static iomux_v3_cfg_t const enet_pads[] = {
 						MUX_PAD_CTRL(ENET_PAD_CTRL)),
 };
 
-static int handle_mac_address(void)
+static int handle_mac_address(char *env_var, uint eeprom_bus)
 {
 	unsigned char enetaddr[6];
 	int rc;
 
-	rc = eth_getenv_enetaddr("ethaddr", enetaddr);
+	rc = eth_getenv_enetaddr(env_var, enetaddr);
 	if (rc)
 		return 0;
 
-	rc = cl_eeprom_read_mac_addr(enetaddr);
+	rc = cl_eeprom_read_mac_addr(enetaddr, eeprom_bus);
 	if (rc)
 		return rc;
 
 	if (!is_valid_ether_addr(enetaddr))
 		return -1;
 
-	return eth_setenv_enetaddr("ethaddr", enetaddr);
+	return eth_setenv_enetaddr(env_var, enetaddr);
 }
 
+#define SB_FX6_I2C_EEPROM_BUS	0
+#define NO_MAC_ADDR		"No MAC address found for %s\n"
 int board_eth_init(bd_t *bis)
 {
 	int err;
 
-	err = handle_mac_address();
-	if (err)
-		puts("No MAC address found\n");
+	if (handle_mac_address("ethaddr", CONFIG_SYS_I2C_EEPROM_BUS))
+		printf(NO_MAC_ADDR, "primary NIC");
+
+	if (handle_mac_address("eth1addr", SB_FX6_I2C_EEPROM_BUS))
+		printf(NO_MAC_ADDR, "secondary NIC");
 
 	SETUP_IOMUX_PADS(enet_pads);
 	/* phy reset */
@@ -464,7 +535,13 @@ int ft_board_setup(void *blob, bd_t *bd)
 
 	/* MAC addr */
 	if (eth_getenv_enetaddr("ethaddr", enetaddr)) {
-		fdt_find_and_setprop(blob, "/fec", "local-mac-address",
+		fdt_find_and_setprop(blob,
+				     "/soc/aips-bus@02100000/ethernet@02188000",
+				     "local-mac-address", enetaddr, 6, 1);
+	}
+
+	if (eth_getenv_enetaddr("eth1addr", enetaddr)) {
+		fdt_find_and_setprop(blob, "/eth@pcie", "local-mac-address",
 				     enetaddr, 6, 1);
 	}
 
@@ -506,6 +583,8 @@ int board_init(void)
 	if (ret)
 		printf("Warning: I2C setup failed: %d\n", ret);
 
+	cm_fx6_setup_display();
+
 	return 0;
 }
 
diff --git a/board/compulab/cm_t335/cm_t335.c b/board/compulab/cm_t335/cm_t335.c
index 9583149bed..592ef3d30f 100644
--- a/board/compulab/cm_t335/cm_t335.c
+++ b/board/compulab/cm_t335/cm_t335.c
@@ -110,7 +110,7 @@ static int handle_mac_address(void)
 	if (rv)
 		return 0;
 
-	rv = cl_eeprom_read_mac_addr(enetaddr);
+	rv = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS);
 	if (rv)
 		get_efuse_mac_addr(enetaddr);
 
diff --git a/board/compulab/cm_t35/cm_t35.c b/board/compulab/cm_t35/cm_t35.c
index 43463d5b47..c4ea8ea875 100644
--- a/board/compulab/cm_t35/cm_t35.c
+++ b/board/compulab/cm_t35/cm_t35.c
@@ -19,6 +19,7 @@
 #include <i2c.h>
 #include <usb.h>
 #include <mmc.h>
+#include <splash.h>
 #include <twl4030.h>
 #include <linux/compiler.h>
 
@@ -59,11 +60,18 @@ void get_board_mem_timings(struct board_sdrc_timings *timings)
 }
 #endif
 
-#define CM_T35_SPLASH_NAND_OFFSET 0x100000
+struct splash_location splash_locations[] = {
+	{
+		.name = "nand",
+		.storage = SPLASH_STORAGE_NAND,
+		.offset = 0x100000,
+	},
+};
 
 int splash_screen_prepare(void)
 {
-	return cl_splash_screen_prepare(CM_T35_SPLASH_NAND_OFFSET);
+	return splash_source_load(splash_locations,
+				  ARRAY_SIZE(splash_locations));
 }
 
 /*
@@ -429,7 +437,7 @@ static int handle_mac_address(void)
 	if (rc)
 		return 0;
 
-	rc = cl_eeprom_read_mac_addr(enetaddr);
+	rc = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS);
 	if (rc)
 		return rc;
 
diff --git a/board/compulab/cm_t3517/cm_t3517.c b/board/compulab/cm_t3517/cm_t3517.c
index cac1ad9ef1..624cf4c034 100644
--- a/board/compulab/cm_t3517/cm_t3517.c
+++ b/board/compulab/cm_t3517/cm_t3517.c
@@ -163,7 +163,7 @@ static int cm_t3517_handle_mac_address(void)
 	if (ret)
 		return 0;
 
-	ret = cl_eeprom_read_mac_addr(enetaddr);
+	ret = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS);
 	if (ret) {
 		ret = am3517_get_efuse_enetaddr(enetaddr);
 		if (ret)
diff --git a/board/compulab/cm_t54/cm_t54.c b/board/compulab/cm_t54/cm_t54.c
index 2c2530ab3f..fdea909ff7 100644
--- a/board/compulab/cm_t54/cm_t54.c
+++ b/board/compulab/cm_t54/cm_t54.c
@@ -165,7 +165,7 @@ static int handle_mac_address(void)
 	if (ret)
 		return 0;
 
-	ret = cl_eeprom_read_mac_addr(enetaddr);
+	ret = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS);
 	if (ret || !is_valid_ether_addr(enetaddr))
 		generate_mac_addr(enetaddr);
 
diff --git a/board/compulab/common/Makefile b/board/compulab/common/Makefile
index dbf0009652..286f32731d 100644
--- a/board/compulab/common/Makefile
+++ b/board/compulab/common/Makefile
@@ -9,5 +9,4 @@
 obj-y				+= common.o
 obj-$(CONFIG_SYS_I2C)		+= eeprom.o
 obj-$(CONFIG_LCD)		+= omap3_display.o
-obj-$(CONFIG_SPLASH_SCREEN)	+= splash.o
 obj-$(CONFIG_SMC911X)		+= omap3_smc911x.o
diff --git a/board/compulab/common/common.h b/board/compulab/common/common.h
index 68ffb111dc..8f38b79fb0 100644
--- a/board/compulab/common/common.h
+++ b/board/compulab/common/common.h
@@ -24,15 +24,6 @@ static inline int cl_usb_hub_init(int gpio, const char *label)
 static inline void cl_usb_hub_deinit(int gpio) {}
 #endif /* CONFIG_CMD_USB */
 
-#ifdef CONFIG_SPLASH_SCREEN
-int cl_splash_screen_prepare(int nand_offset);
-#else /* !CONFIG_SPLASH_SCREEN */
-static inline int cl_splash_screen_prepare(int nand_offset)
-{
-	return -ENOSYS;
-}
-#endif /* CONFIG_SPLASH_SCREEN */
-
 #ifdef CONFIG_SMC911X
 int cl_omap3_smc911x_init(int id, int cs, u32 base_addr,
 			  int (*reset)(int), int rst_gpio);
diff --git a/board/compulab/common/eeprom.c b/board/compulab/common/eeprom.c
index a45e7be11f..77bcea44b4 100644
--- a/board/compulab/common/eeprom.c
+++ b/board/compulab/common/eeprom.c
@@ -31,6 +31,7 @@
 #define LAYOUT_INVALID	0
 #define LAYOUT_LEGACY	0xff
 
+static int cl_eeprom_bus;
 static int cl_eeprom_layout; /* Implicitly LAYOUT_INVALID */
 
 static int cl_eeprom_read(uint offset, uchar *buf, int len)
@@ -38,7 +39,7 @@ static int cl_eeprom_read(uint offset, uchar *buf, int len)
 	int res;
 	unsigned int current_i2c_bus = i2c_get_bus_num();
 
-	res = i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS);
+	res = i2c_set_bus_num(cl_eeprom_bus);
 	if (res < 0)
 		return res;
 
@@ -50,13 +51,18 @@ static int cl_eeprom_read(uint offset, uchar *buf, int len)
 	return res;
 }
 
-static int cl_eeprom_setup_layout(void)
+static int cl_eeprom_setup(uint eeprom_bus)
 {
 	int res;
 
-	if (cl_eeprom_layout != LAYOUT_INVALID)
+	/*
+	 * We know the setup was already done when the layout is set to a valid
+	 * value and we're using the same bus as before.
+	 */
+	if (cl_eeprom_layout != LAYOUT_INVALID && eeprom_bus == cl_eeprom_bus)
 		return 0;
 
+	cl_eeprom_bus = eeprom_bus;
 	res = cl_eeprom_read(EEPROM_LAYOUT_VER_OFFSET,
 			     (uchar *)&cl_eeprom_layout, 1);
 	if (res) {
@@ -77,7 +83,7 @@ void get_board_serial(struct tag_serialnr *serialnr)
 
 	memset(serialnr, 0, sizeof(*serialnr));
 
-	if (cl_eeprom_setup_layout())
+	if (cl_eeprom_setup(CONFIG_SYS_I2C_EEPROM_BUS))
 		return;
 
 	offset = (cl_eeprom_layout != LAYOUT_LEGACY) ?
@@ -96,11 +102,11 @@ void get_board_serial(struct tag_serialnr *serialnr)
  * Routine: cl_eeprom_read_mac_addr
  * Description: read mac address and store it in buf.
  */
-int cl_eeprom_read_mac_addr(uchar *buf)
+int cl_eeprom_read_mac_addr(uchar *buf, uint eeprom_bus)
 {
 	uint offset;
 
-	if (cl_eeprom_setup_layout())
+	if (cl_eeprom_setup(eeprom_bus))
 		return 0;
 
 	offset = (cl_eeprom_layout != LAYOUT_LEGACY) ?
@@ -123,7 +129,7 @@ u32 cl_eeprom_get_board_rev(void)
 	if (board_rev)
 		return board_rev;
 
-	if (cl_eeprom_setup_layout())
+	if (cl_eeprom_setup(CONFIG_SYS_I2C_EEPROM_BUS))
 		return 0;
 
 	if (cl_eeprom_layout != LAYOUT_LEGACY)
diff --git a/board/compulab/common/eeprom.h b/board/compulab/common/eeprom.h
index 85d5bf03d6..50c6b0226f 100644
--- a/board/compulab/common/eeprom.h
+++ b/board/compulab/common/eeprom.h
@@ -11,10 +11,10 @@
 #define _EEPROM_
 
 #ifdef CONFIG_SYS_I2C
-int cl_eeprom_read_mac_addr(uchar *buf);
+int cl_eeprom_read_mac_addr(uchar *buf, uint eeprom_bus);
 u32 cl_eeprom_get_board_rev(void);
 #else
-static inline int cl_eeprom_read_mac_addr(uchar *buf)
+static inline int cl_eeprom_read_mac_addr(uchar *buf, uint eeprom_bus)
 {
 	return 1;
 }
diff --git a/board/compulab/common/splash.c b/board/compulab/common/splash.c
deleted file mode 100644
index 49ed49b81e..0000000000
--- a/board/compulab/common/splash.c
+++ /dev/null
@@ -1,72 +0,0 @@
-/*
- * (C) Copyright 2014 CompuLab, Ltd. <www.compulab.co.il>
- *
- * Authors: Igor Grinberg <grinberg@compulab.co.il>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <nand.h>
-#include <bmp_layout.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_CMD_NAND
-static int splash_load_from_nand(u32 bmp_load_addr, int nand_offset)
-{
-	struct bmp_header *bmp_hdr;
-	int res;
-	size_t bmp_size, bmp_header_size = sizeof(struct bmp_header);
-
-	if (bmp_load_addr + bmp_header_size >= gd->start_addr_sp)
-		goto splash_address_too_high;
-
-	res = nand_read_skip_bad(&nand_info[nand_curr_device],
-			nand_offset, &bmp_header_size,
-			NULL, nand_info[nand_curr_device].size,
-			(u_char *)bmp_load_addr);
-	if (res < 0)
-		return res;
-
-	bmp_hdr = (struct bmp_header *)bmp_load_addr;
-	bmp_size = le32_to_cpu(bmp_hdr->file_size);
-
-	if (bmp_load_addr + bmp_size >= gd->start_addr_sp)
-		goto splash_address_too_high;
-
-	return nand_read_skip_bad(&nand_info[nand_curr_device],
-			nand_offset, &bmp_size,
-			NULL, nand_info[nand_curr_device].size,
-			(u_char *)bmp_load_addr);
-
-splash_address_too_high:
-	printf("Error: splashimage address too high. Data overwrites U-Boot "
-		"and/or placed beyond DRAM boundaries.\n");
-
-	return -1;
-}
-#else
-static inline int splash_load_from_nand(u32 bmp_load_addr, int nand_offset)
-{
-	return -1;
-}
-#endif /* CONFIG_CMD_NAND */
-
-int cl_splash_screen_prepare(int nand_offset)
-{
-	char *env_splashimage_value;
-	u32 bmp_load_addr;
-
-	env_splashimage_value = getenv("splashimage");
-	if (env_splashimage_value == NULL)
-		return -1;
-
-	bmp_load_addr = simple_strtoul(env_splashimage_value, 0, 16);
-	if (bmp_load_addr == 0) {
-		printf("Error: bad splashimage address specified\n");
-		return -1;
-	}
-
-	return splash_load_from_nand(bmp_load_addr, nand_offset);
-}
diff --git a/board/freescale/mx53loco/imximage.cfg b/board/freescale/mx53loco/imximage.cfg
index d1c1931e46..a5f1d98bd1 100644
--- a/board/freescale/mx53loco/imximage.cfg
+++ b/board/freescale/mx53loco/imximage.cfg
@@ -59,7 +59,7 @@ DATA 4 0x63fd9090 0x4d444c44
 DATA 4 0x63fd907c 0x01370138
 DATA 4 0x63fd9080 0x013b013c
 DATA 4 0x63fd9018 0x00011740
-DATA 4 0x63fd9000 0xc3190000
+DATA 4 0x63fd9000 0x83190000
 DATA 4 0x63fd900c 0x9f5152e3
 DATA 4 0x63fd9010 0xb68e8a63
 DATA 4 0x63fd9014 0x01ff00db
@@ -72,6 +72,7 @@ DATA 4 0x63fd901c 0x00008033
 DATA 4 0x63fd901c 0x00028031
 DATA 4 0x63fd901c 0x052080b0
 DATA 4 0x63fd901c 0x04008040
+DATA 4 0x63fd9000 0xc3190000
 DATA 4 0x63fd901c 0x0000803a
 DATA 4 0x63fd901c 0x0000803b
 DATA 4 0x63fd901c 0x00028039
diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
index 59387ffaaa..a90360f2df 100644
--- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
+++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
@@ -311,30 +311,9 @@ static void setup_gpmi_nand(void)
 	/* config gpmi nand iomux */
 	imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
 
-	/* gate ENFC_CLK_ROOT clock first,before clk source switch */
-	clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
-	clrbits_le32(&mxc_ccm->CCGR4,
-		MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK);
-
-	/* config gpmi and bch clock to 100 MHz */
-	clrsetbits_le32(&mxc_ccm->cs2cdr,
-			MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
-			MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
-			MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
-			MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
+	setup_gpmi_io_clk((MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
 			MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
-			MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
-
-	/* enable ENFC_CLK_ROOT clock */
-	setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
-
-	/* enable gpmi and bch clock gating */
-	setbits_le32(&mxc_ccm->CCGR4,
-		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
-		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
-		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
-		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
-		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
+			MXC_CCM_CS2CDR_ENFC_CLK_SEL(3)));
 
 	/* enable apbh clock gating */
 	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
diff --git a/board/freescale/mx6sxsabresd/MAINTAINERS b/board/freescale/mx6sxsabresd/MAINTAINERS
index f52f300bed..c0f5d9c8e4 100644
--- a/board/freescale/mx6sxsabresd/MAINTAINERS
+++ b/board/freescale/mx6sxsabresd/MAINTAINERS
@@ -4,3 +4,4 @@ S:	Maintained
 F:	board/freescale/mx6sxsabresd/
 F:	include/configs/mx6sxsabresd.h
 F:	configs/mx6sxsabresd_defconfig
+F:	configs/mx6sxsabresd_spl_defconfig
diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
index 5cc58ac868..a2c9aae32c 100644
--- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
+++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
@@ -326,6 +326,7 @@ int board_mmc_getcd(struct mmc *mmc)
 
 int board_mmc_init(bd_t *bis)
 {
+#ifndef CONFIG_SPL_BUILD
 	int i, ret;
 
 	/*
@@ -369,6 +370,47 @@ int board_mmc_init(bd_t *bis)
 	}
 
 	return 0;
+#else
+	struct src *src_regs = (struct src *)SRC_BASE_ADDR;
+	u32 val;
+	u32 port;
+
+	val = readl(&src_regs->sbmr1);
+
+	if ((val & 0xc0) != 0x40) {
+		printf("Not boot from USDHC!\n");
+		return -EINVAL;
+	}
+
+	port = (val >> 11) & 0x3;
+	printf("port %d\n", port);
+	switch (port) {
+	case 1:
+		imx_iomux_v3_setup_multiple_pads(
+			usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+		usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+		break;
+	case 2:
+		imx_iomux_v3_setup_multiple_pads(
+			usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+		gpio_direction_input(USDHC3_CD_GPIO);
+		gpio_direction_output(USDHC3_PWR_GPIO, 1);
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+		usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
+		break;
+	case 3:
+		imx_iomux_v3_setup_multiple_pads(
+			usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+		gpio_direction_input(USDHC4_CD_GPIO);
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+		usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
+		break;
+	}
+
+	gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+#endif
 }
 
 #ifdef CONFIG_FSL_QSPI
@@ -423,14 +465,135 @@ int board_init(void)
 	return 0;
 }
 
-int board_late_init(void)
+int checkboard(void)
 {
+	puts("Board: MX6SX SABRE SDB\n");
+
 	return 0;
 }
 
-int checkboard(void)
+#ifdef CONFIG_SPL_BUILD
+#include <libfdt.h>
+#include <spl.h>
+#include <asm/arch/mx6-ddr.h>
+
+const struct mx6sx_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_dqm0 = 0x00000028,
+	.dram_dqm1 = 0x00000028,
+	.dram_dqm2 = 0x00000028,
+	.dram_dqm3 = 0x00000028,
+	.dram_ras = 0x00000020,
+	.dram_cas = 0x00000020,
+	.dram_odt0 = 0x00000020,
+	.dram_odt1 = 0x00000020,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdcke0 = 0x00003000,
+	.dram_sdcke1 = 0x00003000,
+	.dram_sdclk_0 = 0x00000030,
+	.dram_sdqs0 = 0x00000028,
+	.dram_sdqs1 = 0x00000028,
+	.dram_sdqs2 = 0x00000028,
+	.dram_sdqs3 = 0x00000028,
+	.dram_reset = 0x00000020,
+};
+
+const struct mx6sx_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_addds = 0x00000020,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_ddrpke = 0x00000000,
+	.grp_ddrmode = 0x00020000,
+	.grp_b0ds = 0x00000028,
+	.grp_b1ds = 0x00000028,
+	.grp_ctlds = 0x00000020,
+	.grp_ddr_type = 0x000c0000,
+	.grp_b2ds = 0x00000028,
+	.grp_b3ds = 0x00000028,
+};
+
+const struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 = 0x00290025,
+	.p0_mpwldectrl1 = 0x00220022,
+	.p0_mpdgctrl0 = 0x41480144,
+	.p0_mpdgctrl1 = 0x01340130,
+	.p0_mprddlctl = 0x3C3E4244,
+	.p0_mpwrdlctl = 0x34363638,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 1600,
+	.density = 4,
+	.width = 32,
+	.banks = 8,
+	.rowaddr = 15,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static void ccgr_init(void)
 {
-	puts("Board: MX6SX SABRE SDB\n");
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0xFFFFFFFF, &ccm->CCGR0);
+	writel(0xFFFFFFFF, &ccm->CCGR1);
+	writel(0xFFFFFFFF, &ccm->CCGR2);
+	writel(0xFFFFFFFF, &ccm->CCGR3);
+	writel(0xFFFFFFFF, &ccm->CCGR4);
+	writel(0xFFFFFFFF, &ccm->CCGR5);
+	writel(0xFFFFFFFF, &ccm->CCGR6);
+	writel(0xFFFFFFFF, &ccm->CCGR7);
+}
 
-	return 0;
+static void spl_dram_init(void)
+{
+	struct mx6_ddr_sysinfo sysinfo = {
+		.dsize = mem_ddr.width/32,
+		.cs_density = 24,
+		.ncs = 1,
+		.cs1_mirror = 0,
+		.rtt_wr = 2,
+		.rtt_nom = 2,		/* RTT_Nom = RZQ/2 */
+		.walat = 1,		/* Write additional latency */
+		.ralat = 5,		/* Read additional latency */
+		.mif3_mode = 3,		/* Command prediction working mode */
+		.bi_on = 1,		/* Bank interleaving enabled */
+		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+	};
+
+	mx6sx_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+
+	/* iomux and setup of i2c */
+	board_early_init_f();
+
+	/* setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
 }
+
+void reset_cpu(ulong addr)
+{
+}
+#endif