ZOOM2 Add serial support.

Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS.  On your host pick the first
enumeration.

The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.

The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.

The kernel bootargs are
console=ttyS3,115200n8

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>

4 files changed, 245 insertions, 1 deletions

diff --git a/board/omap3/zoom2/Makefile b/board/omap3/zoom2/Makefile
index b8fa5a78bb..d27990c993 100644
--- a/board/omap3/zoom2/Makefile
+++ b/board/omap3/zoom2/Makefile
@@ -26,7 +26,8 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 
 COBJS	:= zoom2.o \
-	debug_board.o
+	debug_board.o \
+	zoom2_serial.o
 
 SRCS	:= $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
diff --git a/board/omap3/zoom2/zoom2.c b/board/omap3/zoom2/zoom2.c
index 0700c56d70..83e02f6b46 100644
--- a/board/omap3/zoom2/zoom2.c
+++ b/board/omap3/zoom2/zoom2.c
@@ -30,10 +30,32 @@
  */
 #include <common.h>
 #include <asm/io.h>
+#include <asm/arch/mem.h>
 #include <asm/arch/mux.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/mach-types.h>
 #include "zoom2.h"
+#include "zoom2_serial.h"
+
+/*
+ * This the the zoom2, board specific, gpmc configuration for the
+ * quad uart on the debug board.   The more general gpmc configurations
+ * are setup at the cpu level in cpu/arm_cortexa8/omap3/mem.c
+ *
+ * The details of the setting of the serial gpmc setup are not available.
+ * The values were provided by another party.
+ */
+extern void enable_gpmc_config(u32 *gpmc_config, gpmc_csx_t *gpmc_cs_base,
+			       u32 base, u32 size);
+
+static u32 gpmc_serial_TL16CP754C[GPMC_MAX_REG] = {
+	0x00011000,
+	0x001F1F01,
+	0x00080803,
+	0x1D091D09,
+	0x041D1F1F,
+	0x1D0904C4, 0
+};
 
 /*
  * Routine: board_init
@@ -42,13 +64,29 @@
 int board_init (void)
 {
 	DECLARE_GLOBAL_DATA_PTR;
+	gpmc_csx_t *serial_cs_base;
+	u32 *gpmc_config;
 
 	gpmc_init ();		/* in SRAM or SDRAM, finish GPMC */
+
+	/* Configure console support on zoom2 */
+	gpmc_config = gpmc_serial_TL16CP754C;
+	serial_cs_base = (gpmc_csx_t *) (GPMC_CONFIG_CS0_BASE +
+					 (3 * GPMC_CONFIG_WIDTH));
+	enable_gpmc_config(gpmc_config,
+			   serial_cs_base,
+			   SERIAL_TL16CP754C_BASE,
+			   GPMC_SIZE_16M);
+
 	/* board id for Linux */
 	gd->bd->bi_arch_number = MACH_TYPE_OMAP_ZOOM2;
 	/* boot param addr */
 	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
 
+#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
+	status_led_set (STATUS_LED_BOOT, STATUS_LED_ON);
+#endif
+
 	return 0;
 }
 
diff --git a/board/omap3/zoom2/zoom2_serial.c b/board/omap3/zoom2/zoom2_serial.c
new file mode 100644
index 0000000000..a3d777dfad
--- /dev/null
+++ b/board/omap3/zoom2/zoom2_serial.c
@@ -0,0 +1,130 @@
+/*
+ * Copyright (c) 2009 Wind River Systems, Inc.
+ * Tom Rix <Tom.Rix@windriver.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * This file was adapted from cpu/mpc5xxx/serial.c
+ *
+ */
+
+#include <common.h>
+#include <serial.h>
+#include <ns16550.h>
+#include <asm/arch/cpu.h>
+#include "zoom2_serial.h"
+
+int quad_init_dev (unsigned long base)
+{
+	/*
+	 * The Quad UART is on the debug board.
+	 * Check if the debug board is attached before using the UART
+	 */
+	if (zoom2_debug_board_connected ()) {
+		NS16550_t com_port = (NS16550_t) base;
+		int baud_divisor = CONFIG_SYS_NS16550_CLK / 16 /
+			CONFIG_BAUDRATE;
+
+		/*
+		 * Zoom2 has a board specific initialization of its UART.
+		 * This generic initialization has been copied from
+		 * drivers/serial/ns16550.c. The macros have been expanded.
+		 *
+		 * Do the following instead of
+		 *
+		 * NS16550_init (com_port, clock_divisor);
+		 */
+		com_port->ier = 0x00;
+
+		/*
+		 * On Zoom2 board Set pre-scalar to 1
+		 * CLKSEL is GND => MCR[7] is 1 => preslr is 4
+		 * So change the prescl to 1
+		 */
+		com_port->lcr = 0xBF;
+		com_port->fcr |= 0x10;
+		com_port->mcr &= 0x7F;
+
+		/* This is generic ns16550.c setup */
+		com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1;
+		com_port->dll = 0;
+		com_port->dlm = 0;
+		com_port->lcr = UART_LCR_8N1;
+		com_port->mcr = UART_MCR_DTR | UART_MCR_RTS;
+		com_port->fcr = UART_FCR_FIFO_EN | UART_FCR_RXSR |
+			UART_FCR_TXSR;
+		com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1;
+		com_port->dll = baud_divisor & 0xff;
+		com_port->dlm = (baud_divisor >> 8) & 0xff;
+		com_port->lcr = UART_LCR_8N1;
+	}
+	/*
+	 * We have to lie here, otherwise the board init code will hang
+	 * on the check
+	 */
+	return 0;
+}
+
+void quad_putc_dev (unsigned long base, const char c)
+{
+	if (zoom2_debug_board_connected ()) {
+
+		if (c == '\n')
+			quad_putc_dev (base, '\r');
+
+		NS16550_putc ((NS16550_t) base, c);
+	}
+}
+
+void quad_puts_dev (unsigned long base, const char *s)
+{
+	if (zoom2_debug_board_connected ()) {
+		while ((s != NULL) && (*s != '\0'))
+			quad_putc_dev (base, *s++);
+	}
+}
+
+int quad_getc_dev (unsigned long base)
+{
+	if (zoom2_debug_board_connected ())
+		return NS16550_getc ((NS16550_t) base);
+	else
+		return 0;
+}
+
+int quad_tstc_dev (unsigned long base)
+{
+	if (zoom2_debug_board_connected ())
+		return NS16550_tstc ((NS16550_t) base);
+	else
+		return 0;
+}
+
+void quad_setbrg_dev (unsigned long base)
+{
+	if (zoom2_debug_board_connected ()) {
+
+		int clock_divisor = CONFIG_SYS_NS16550_CLK / 16 /
+			CONFIG_BAUDRATE;
+
+		NS16550_reinit ((NS16550_t) base, clock_divisor);
+	}
+}
+
+QUAD_INIT (0)
+QUAD_INIT (1)
+QUAD_INIT (2)
+QUAD_INIT (3)
diff --git a/board/omap3/zoom2/zoom2_serial.h b/board/omap3/zoom2/zoom2_serial.h
new file mode 100644
index 0000000000..c98158f1ba
--- /dev/null
+++ b/board/omap3/zoom2/zoom2_serial.h
@@ -0,0 +1,75 @@
+/*
+ * Copyright (c) 2009 Wind River Systems, Inc.
+ * Tom Rix <Tom.Rix@windriver.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#ifndef ZOOM2_SERIAL_H
+#define ZOOM2_SERIAL_H
+
+extern int zoom2_debug_board_connected (void);
+
+#define SERIAL_TL16CP754C_BASE	0x10000000	/* Zoom2 Serial chip address */
+
+#define QUAD_BASE_0	SERIAL_TL16CP754C_BASE
+#define QUAD_BASE_1	(SERIAL_TL16CP754C_BASE + 0x100)
+#define QUAD_BASE_2	(SERIAL_TL16CP754C_BASE + 0x200)
+#define QUAD_BASE_3	(SERIAL_TL16CP754C_BASE + 0x300)
+
+#define S(a) #a
+#define N(a) S(quad##a)
+#define U(a) S(UART##a)
+
+#define QUAD_INIT(n)				\
+int quad_init_##n(void)				\
+{						\
+	return quad_init_dev(QUAD_BASE_##n);	\
+}						\
+void quad_setbrg_##n(void)			\
+{						\
+	quad_setbrg_dev(QUAD_BASE_##n);		\
+}						\
+void quad_putc_##n(const char c)		\
+{						\
+	quad_putc_dev(QUAD_BASE_##n, c);	\
+}						\
+void quad_puts_##n(const char *s)		\
+{						\
+	quad_puts_dev(QUAD_BASE_##n, s);	\
+}						\
+int quad_getc_##n(void)				\
+{						\
+	return quad_getc_dev(QUAD_BASE_##n);	\
+}						\
+int quad_tstc_##n(void)				\
+{						\
+	return quad_tstc_dev(QUAD_BASE_##n);	\
+}						\
+struct serial_device zoom2_serial_device##n =	\
+{						\
+	N(n),					\
+	U(n),					\
+	quad_init_##n,				\
+	quad_setbrg_##n,			\
+	quad_getc_##n,				\
+	quad_tstc_##n,				\
+	quad_putc_##n,				\
+	quad_puts_##n,				\
+};
+
+#endif /* ZOOM2_SERIAL_H */