arm: Remove snapper9260 board

This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.

Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

4 files changed, 0 insertions, 182 deletions

diff --git a/board/bluewater/snapper9260/Kconfig b/board/bluewater/snapper9260/Kconfig
deleted file mode 100644
index b8e9cbc585..0000000000
--- a/board/bluewater/snapper9260/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_SNAPPER9260
-
-config SYS_BOARD
-	default "snapper9260"
-
-config SYS_VENDOR
-	default "bluewater"
-
-config SYS_CONFIG_NAME
-	default "snapper9260"
-
-endif
diff --git a/board/bluewater/snapper9260/MAINTAINERS b/board/bluewater/snapper9260/MAINTAINERS
deleted file mode 100644
index 1f8f4d6988..0000000000
--- a/board/bluewater/snapper9260/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-SNAPPER9260 BOARD
-M:	Simon Glass <sjg@chromium.org>
-S:	Maintained
-F:	board/bluewater/snapper9260/
-F:	include/configs/snapper9260.h
-F:	configs/snapper9260_defconfig
-F:	configs/snapper9g20_defconfig
diff --git a/board/bluewater/snapper9260/Makefile b/board/bluewater/snapper9260/Makefile
deleted file mode 100644
index 842abf4eee..0000000000
--- a/board/bluewater/snapper9260/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2003-2008
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# (C) Copyright 2011 Bluewater Systems
-# Ryan Mallon <ryan@bluewatersys.com>
-
-obj-y	+= snapper9260.o
diff --git a/board/bluewater/snapper9260/snapper9260.c b/board/bluewater/snapper9260/snapper9260.c
deleted file mode 100644
index df53a651c3..0000000000
--- a/board/bluewater/snapper9260/snapper9260.c
+++ /dev/null
@@ -1,154 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Bluewater Systems Snapper 9260/9G20 modules
- *
- * (C) Copyright 2011 Bluewater Systems
- *   Author: Andre Renaud <andre@bluewatersys.com>
- *   Author: Ryan Mallon <ryan@bluewatersys.com>
- */
-
-#include <common.h>
-#include <dm.h>
-#include <init.h>
-#include <asm/global_data.h>
-#include <asm/io.h>
-#include <asm/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/arch/at91sam9260_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
-#include <asm/arch/at91_common.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/atmel_serial.h>
-#include <net.h>
-#include <netdev.h>
-#include <i2c.h>
-#include <pca953x.h>
-#include <linux/delay.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* IO Expander pins */
-#define IO_EXP_ETH_RESET	(0 << 1)
-#define IO_EXP_ETH_POWER	(1 << 1)
-
-static void macb_hw_init(void)
-{
-	struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
-
-	at91_periph_clk_enable(ATMEL_ID_EMAC0);
-
-	/* Disable pull-ups to prevent PHY going into test mode */
-	writel(pin_to_mask(AT91_PIN_PA14) |
-	       pin_to_mask(AT91_PIN_PA15) |
-	       pin_to_mask(AT91_PIN_PA18),
-	       &pioa->pudr);
-
-	/* Power down ethernet */
-	pca953x_set_dir(0x28, IO_EXP_ETH_POWER, PCA953X_DIR_OUT);
-	pca953x_set_val(0x28, IO_EXP_ETH_POWER, 1);
-
-	/* Hold ethernet in reset */
-	pca953x_set_dir(0x28, IO_EXP_ETH_RESET, PCA953X_DIR_OUT);
-	pca953x_set_val(0x28, IO_EXP_ETH_RESET, 0);
-
-	/* Enable ethernet power */
-	pca953x_set_val(0x28, IO_EXP_ETH_POWER, 0);
-
-	at91_phy_reset();
-
-	/* Bring the ethernet out of reset */
-	pca953x_set_val(0x28, IO_EXP_ETH_RESET, 1);
-
-	/* The phy internal reset take 21ms */
-	udelay(21 * 1000);
-
-	/* Re-enable pull-up */
-	writel(pin_to_mask(AT91_PIN_PA14) |
-	       pin_to_mask(AT91_PIN_PA15) |
-	       pin_to_mask(AT91_PIN_PA18),
-	       &pioa->puer);
-
-	at91_macb_hw_init();
-}
-
-static void nand_hw_init(void)
-{
-	struct at91_smc *smc       = (struct at91_smc    *)ATMEL_BASE_SMC;
-	struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
-	unsigned long csa;
-
-	/* Enable CS3 as NAND/SmartMedia */
-	csa = readl(&matrix->ebicsa);
-	csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
-	writel(csa, &matrix->ebicsa);
-
-	/* Configure SMC CS3 for NAND/SmartMedia */
-	writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
-	       AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
-	       &smc->cs[3].setup);
-	writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(4) |
-	       AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(4),
-	       &smc->cs[3].pulse);
-	writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
-	       &smc->cs[3].cycle);
-	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
-	       AT91_SMC_MODE_EXNW_DISABLE |
-	       AT91_SMC_MODE_DBW_8 |
-	       AT91_SMC_MODE_TDF_CYCLE(3),
-	       &smc->cs[3].mode);
-
-	/* Configure RDY/BSY */
-	gpio_request(CONFIG_SYS_NAND_READY_PIN, "nand_rdy");
-	gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
-
-	/* Enable NandFlash */
-	gpio_request(CONFIG_SYS_NAND_ENABLE_PIN, "nand_ce");
-	gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
-}
-
-int board_init(void)
-{
-	at91_periph_clk_enable(ATMEL_ID_PIOA);
-	at91_periph_clk_enable(ATMEL_ID_PIOB);
-	at91_periph_clk_enable(ATMEL_ID_PIOC);
-
-	/* The mach-type is the same for both Snapper 9260 and 9G20 */
-	gd->bd->bi_arch_number = MACH_TYPE_SNAPPER_9260;
-
-	/* Address of boot parameters */
-	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
-	/* Initialise peripherals */
-	at91_seriald_hw_init();
-	i2c_set_bus_num(0);
-	nand_hw_init();
-	macb_hw_init();
-
-	return 0;
-}
-
-int board_eth_init(struct bd_info *bis)
-{
-	return macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x1f);
-}
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
-				    CONFIG_SYS_SDRAM_SIZE);
-	return 0;
-}
-
-void reset_phy(void)
-{
-}
-
-static struct atmel_serial_plat at91sam9260_serial_plat = {
-	.base_addr = ATMEL_BASE_DBGU,
-};
-
-U_BOOT_DRVINFO(at91sam9260_serial) = {
-	.name	= "serial_atmel",
-	.plat = &at91sam9260_serial_plat,
-};