arm: dts: k3-am62: Bump dtsi from linux v6.5-rc1

Update the am62 and am625 device-trees from linux v6.5-rc1. This needed
the following tweaks to the u-boot specific dtsi as well:
- Switch tick-timer to the main_timer as it's now defined in the main dtsi
- Secure proxies are defined in SoC dtsi
- Drop duplicate nodes - u-boot.dtsi is includes in r5-sk, no need for
  either the definitions from main.dtsi OR duplication from u-boot.dtsi

Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Sjoerd Simons <sjoerd@collabora.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>

11 files changed, 1064 insertions, 398 deletions

diff --git a/arch/arm/dts/k3-am62-main.dtsi b/arch/arm/dts/k3-am62-main.dtsi
index 4a42f1b2e3..2488e3a537 100644
--- a/arch/arm/dts/k3-am62-main.dtsi
+++ b/arch/arm/dts/k3-am62-main.dtsi
@@ -54,6 +54,12 @@
 			reg = <0x4044 0x8>;
 			#phy-cells = <1>;
 		};
+
+		epwm_tbclk: clock@4130 {
+			compatible = "ti,am62-epwm-tbclk", "syscon";
+			reg = <0x4130 0x4>;
+			#clock-cells = <1>;
+		};
 	};
 
 	dmss: bus@48000000 {
@@ -144,8 +150,8 @@
 		compatible = "ti,k2g-sci";
 		ti,host-id = <12>;
 		mbox-names = "rx", "tx";
-		mboxes= <&secure_proxy_main 12>,
-			<&secure_proxy_main 13>;
+		mboxes = <&secure_proxy_main 12>,
+			 <&secure_proxy_main 13>;
 		reg-names = "debug_messages";
 		reg = <0x00 0x44043000 0x00 0xfe0>;
 
@@ -178,6 +184,21 @@
 		dma-names = "tx", "rx1", "rx2";
 	};
 
+	secure_proxy_sa3: mailbox@43600000 {
+		compatible = "ti,am654-secure-proxy";
+		#mbox-cells = <1>;
+		reg-names = "target_data", "rt", "scfg";
+		reg = <0x00 0x43600000 0x00 0x10000>,
+		      <0x00 0x44880000 0x00 0x20000>,
+		      <0x00 0x44860000 0x00 0x20000>;
+		/*
+		 * Marked Disabled:
+		 * Node is incomplete as it is meant for bootloaders and
+		 * firmware on non-MPU processors
+		 */
+		status = "disabled";
+	};
+
 	main_pmx0: pinctrl@f4000 {
 		compatible = "pinctrl-single";
 		reg = <0x00 0xf4000 0x00 0x2ac>;
@@ -186,6 +207,108 @@
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
 
+	main_esm: esm@420000 {
+		compatible = "ti,j721e-esm";
+		reg = <0x00 0x420000 0x00 0x1000>;
+		ti,esm-pins = <160>, <161>, <162>, <163>, <177>, <178>;
+	};
+
+	main_timer0: timer@2400000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2400000 0x00 0x400>;
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 36 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 36 2>;
+		assigned-clock-parents = <&k3_clks 36 3>;
+		power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer1: timer@2410000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2410000 0x00 0x400>;
+		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 37 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 37 2>;
+		assigned-clock-parents = <&k3_clks 37 3>;
+		power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer2: timer@2420000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2420000 0x00 0x400>;
+		interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 38 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 38 2>;
+		assigned-clock-parents = <&k3_clks 38 3>;
+		power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer3: timer@2430000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2430000 0x00 0x400>;
+		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 39 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 39 2>;
+		assigned-clock-parents = <&k3_clks 39 3>;
+		power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer4: timer@2440000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2440000 0x00 0x400>;
+		interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 40 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 40 2>;
+		assigned-clock-parents = <&k3_clks 40 3>;
+		power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer5: timer@2450000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2450000 0x00 0x400>;
+		interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 41 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 41 2>;
+		assigned-clock-parents = <&k3_clks 41 3>;
+		power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer6: timer@2460000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2460000 0x00 0x400>;
+		interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 42 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 42 2>;
+		assigned-clock-parents = <&k3_clks 42 3>;
+		power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
+	main_timer7: timer@2470000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x2470000 0x00 0x400>;
+		interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 43 2>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 43 2>;
+		assigned-clock-parents = <&k3_clks 43 3>;
+		power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+	};
+
 	main_uart0: serial@2800000 {
 		compatible = "ti,am64-uart", "ti,am654-uart";
 		reg = <0x00 0x02800000 0x00 0x100>;
@@ -193,6 +316,7 @@
 		power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 146 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart1: serial@2810000 {
@@ -202,6 +326,7 @@
 		power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 152 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart2: serial@2820000 {
@@ -211,6 +336,7 @@
 		power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 153 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart3: serial@2830000 {
@@ -220,6 +346,7 @@
 		power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 154 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart4: serial@2840000 {
@@ -229,6 +356,7 @@
 		power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 155 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart5: serial@2850000 {
@@ -238,6 +366,7 @@
 		power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 156 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart6: serial@2860000 {
@@ -247,6 +376,7 @@
 		power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 158 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_i2c0: i2c@20000000 {
@@ -258,6 +388,7 @@
 		power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 102 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	main_i2c1: i2c@20010000 {
@@ -269,6 +400,7 @@
 		power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 103 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	main_i2c2: i2c@20020000 {
@@ -280,6 +412,7 @@
 		power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 104 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	main_i2c3: i2c@20030000 {
@@ -291,6 +424,7 @@
 		power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 105 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	main_spi0: spi@20100000 {
@@ -300,7 +434,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
-		clocks = <&k3_clks 172 0>;
+		clocks = <&k3_clks 141 0>;
+		status = "disabled";
 	};
 
 	main_spi1: spi@20110000 {
@@ -310,7 +445,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
-		clocks = <&k3_clks 173 0>;
+		clocks = <&k3_clks 142 0>;
+		status = "disabled";
 	};
 
 	main_spi2: spi@20120000 {
@@ -320,7 +456,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
-		clocks = <&k3_clks 174 0>;
+		clocks = <&k3_clks 143 0>;
+		status = "disabled";
 	};
 
 	main_gpio_intr: interrupt-controller@a00000 {
@@ -345,7 +482,7 @@
 			     <193>, <194>, <195>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
-		ti,ngpio = <87>;
+		ti,ngpio = <92>;
 		ti,davinci-gpio-unbanked = <0>;
 		power-domains = <&k3_pds 77 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 77 0>;
@@ -362,7 +499,7 @@
 			     <183>, <184>, <185>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
-		ti,ngpio = <88>;
+		ti,ngpio = <52>;
 		ti,davinci-gpio-unbanked = <0>;
 		power-domains = <&k3_pds 78 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 78 0>;
@@ -385,8 +522,11 @@
 		ti,clkbuf-sel = <0x7>;
 		ti,otap-del-sel-legacy = <0x0>;
 		ti,otap-del-sel-mmc-hs = <0x0>;
-		ti,otap-del-sel-ddr52 = <0x9>;
-		ti,otap-del-sel-hs200 = <0x6>;
+		ti,otap-del-sel-ddr52 = <0x5>;
+		ti,otap-del-sel-hs200 = <0x5>;
+		ti,itap-del-sel-legacy = <0xa>;
+		ti,itap-del-sel-mmc-hs = <0x1>;
+		status = "disabled";
 	};
 
 	sdhci1: mmc@fa00000 {
@@ -397,19 +537,20 @@
 		clocks = <&k3_clks 58 5>, <&k3_clks 58 6>;
 		clock-names = "clk_ahb", "clk_xin";
 		ti,trm-icp = <0x2>;
-		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-legacy = <0x8>;
 		ti,otap-del-sel-sd-hs = <0x0>;
-		ti,otap-del-sel-sdr12 = <0xf>;
-		ti,otap-del-sel-sdr25 = <0xf>;
-		ti,otap-del-sel-sdr50 = <0xc>;
-		ti,otap-del-sel-sdr104 = <0x6>;
-		ti,otap-del-sel-ddr50 = <0x9>;
-		ti,itap-del-sel-legacy = <0x0>;
-		ti,itap-del-sel-sd-hs = <0x0>;
-		ti,itap-del-sel-sdr12 = <0x0>;
-		ti,itap-del-sel-sdr25 = <0x0>;
+		ti,otap-del-sel-sdr12 = <0x0>;
+		ti,otap-del-sel-sdr25 = <0x0>;
+		ti,otap-del-sel-sdr50 = <0x8>;
+		ti,otap-del-sel-sdr104 = <0x7>;
+		ti,otap-del-sel-ddr50 = <0x4>;
+		ti,itap-del-sel-legacy = <0xa>;
+		ti,itap-del-sel-sd-hs = <0x1>;
+		ti,itap-del-sel-sdr12 = <0xa>;
+		ti,itap-del-sel-sdr25 = <0x1>;
 		ti,clkbuf-sel = <0x7>;
 		bus-width = <4>;
+		status = "disabled";
 	};
 
 	sdhci2: mmc@fa20000 {
@@ -420,18 +561,65 @@
 		clocks = <&k3_clks 184 5>, <&k3_clks 184 6>;
 		clock-names = "clk_ahb", "clk_xin";
 		ti,trm-icp = <0x2>;
-		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-legacy = <0x8>;
 		ti,otap-del-sel-sd-hs = <0x0>;
-		ti,otap-del-sel-sdr12 = <0xf>;
-		ti,otap-del-sel-sdr25 = <0xf>;
-		ti,otap-del-sel-sdr50 = <0xc>;
-		ti,otap-del-sel-sdr104 = <0x6>;
-		ti,otap-del-sel-ddr50 = <0x9>;
-		ti,itap-del-sel-legacy = <0x0>;
-		ti,itap-del-sel-sd-hs = <0x0>;
-		ti,itap-del-sel-sdr12 = <0x0>;
-		ti,itap-del-sel-sdr25 = <0x0>;
+		ti,otap-del-sel-sdr12 = <0x0>;
+		ti,otap-del-sel-sdr25 = <0x0>;
+		ti,otap-del-sel-sdr50 = <0x8>;
+		ti,otap-del-sel-sdr104 = <0x7>;
+		ti,otap-del-sel-ddr50 = <0x8>;
+		ti,itap-del-sel-legacy = <0xa>;
+		ti,itap-del-sel-sd-hs = <0xa>;
+		ti,itap-del-sel-sdr12 = <0xa>;
+		ti,itap-del-sel-sdr25 = <0x1>;
 		ti,clkbuf-sel = <0x7>;
+		status = "disabled";
+	};
+
+	usbss0: dwc3-usb@f900000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f900000 0x00 0x800>;
+		clocks = <&k3_clks 161 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb0: usb@31000000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31000000 0x00 0x50000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	usbss1: dwc3-usb@f910000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f910000 0x00 0x800>;
+		clocks = <&k3_clks 162 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb1: usb@31100000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31100000 0x00 0x50000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
 	};
 
 	fss: bus@fc00000 {
@@ -456,6 +644,7 @@
 			power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			status = "disabled";
 		};
 	};
 
@@ -514,12 +703,13 @@
 			clocks = <&k3_clks 13 0>;
 			clock-names = "fck";
 			bus_freq = <1000000>;
+			status = "disabled";
 		};
 
 		cpts@3d000 {
 			compatible = "ti,j721e-cpts";
 			reg = <0x00 0x3d000 0x00 0x400>;
-			clocks = <&k3_clks 13 1>;
+			clocks = <&k3_clks 13 3>;
 			clock-names = "cpts";
 			interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "cpts";
@@ -551,6 +741,7 @@
 		power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 51 0>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	ecap1: pwm@23110000 {
@@ -560,6 +751,7 @@
 		power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 52 0>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	ecap2: pwm@23120000 {
@@ -569,6 +761,7 @@
 		power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 53 0>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	main_mcan0: can@20701000 {
@@ -583,5 +776,141 @@
 			     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "int0", "int1";
 		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+		status = "disabled";
+	};
+
+	main_rti0: watchdog@e000000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x0e000000 0x00 0x100>;
+		clocks = <&k3_clks 125 0>;
+		power-domains = <&k3_pds 125 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 125 0>;
+		assigned-clock-parents = <&k3_clks 125 2>;
+	};
+
+	main_rti1: watchdog@e010000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x0e010000 0x00 0x100>;
+		clocks = <&k3_clks 126 0>;
+		power-domains = <&k3_pds 126 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 126 0>;
+		assigned-clock-parents = <&k3_clks 126 2>;
+	};
+
+	main_rti2: watchdog@e020000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x0e020000 0x00 0x100>;
+		clocks = <&k3_clks 127 0>;
+		power-domains = <&k3_pds 127 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 127 0>;
+		assigned-clock-parents = <&k3_clks 127 2>;
+	};
+
+	main_rti3: watchdog@e030000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x0e030000 0x00 0x100>;
+		clocks = <&k3_clks 128 0>;
+		power-domains = <&k3_pds 128 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 128 0>;
+		assigned-clock-parents = <&k3_clks 128 2>;
+	};
+
+	main_rti15: watchdog@e0f0000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x0e0f0000 0x00 0x100>;
+		clocks = <&k3_clks 130 0>;
+		power-domains = <&k3_pds 130 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 130 0>;
+		assigned-clock-parents = <&k3_clks 130 2>;
+	};
+
+	epwm0: pwm@23000000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23000000 0x00 0x100>;
+		power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	epwm1: pwm@23010000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23010000 0x00 0x100>;
+		power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	epwm2: pwm@23020000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23020000 0x00 0x100>;
+		power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>;
+		clock-names = "tbclk", "fck";
+		status = "disabled";
+	};
+
+	mcasp0: audio-controller@2b00000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b00000 0x00 0x2000>,
+		      <0x00 0x02b08000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 190 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 190 0>;
+		assigned-clock-parents = <&k3_clks 190 2>;
+		power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
+
+	mcasp1: audio-controller@2b10000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b10000 0x00 0x2000>,
+		      <0x00 0x02b18000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 191 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 191 0>;
+		assigned-clock-parents = <&k3_clks 191 2>;
+		power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
+
+	mcasp2: audio-controller@2b20000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b20000 0x00 0x2000>,
+		      <0x00 0x02b28000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 192 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 192 0>;
+		assigned-clock-parents = <&k3_clks 192 2>;
+		power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
 	};
 };
diff --git a/arch/arm/dts/k3-am62-mcu.dtsi b/arch/arm/dts/k3-am62-mcu.dtsi
index f56c803560..19fc38157d 100644
--- a/arch/arm/dts/k3-am62-mcu.dtsi
+++ b/arch/arm/dts/k3-am62-mcu.dtsi
@@ -14,6 +14,57 @@
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
 
+	mcu_esm: esm@4100000 {
+		compatible = "ti,j721e-esm";
+		reg = <0x00 0x4100000 0x00 0x1000>;
+		ti,esm-pins = <0>, <1>, <2>, <85>;
+	};
+
+	/*
+	 * The MCU domain timer interrupts are routed only to the ESM module,
+	 * and not currently available for Linux. The MCU domain timers are
+	 * of limited use without interrupts, and likely reserved by the ESM.
+	 */
+	mcu_timer0: timer@4800000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4800000 0x00 0x400>;
+		clocks = <&k3_clks 35 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer1: timer@4810000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4810000 0x00 0x400>;
+		clocks = <&k3_clks 48 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer2: timer@4820000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4820000 0x00 0x400>;
+		clocks = <&k3_clks 49 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
+	mcu_timer3: timer@4830000 {
+		compatible = "ti,am654-timer";
+		reg = <0x00 0x4830000 0x00 0x400>;
+		clocks = <&k3_clks 50 2>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>;
+		ti,timer-pwm;
+		status = "reserved";
+	};
+
 	mcu_uart0: serial@4a00000 {
 		compatible = "ti,am64-uart", "ti,am654-uart";
 		reg = <0x00 0x04a00000 0x00 0x100>;
@@ -21,6 +72,7 @@
 		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 149 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	mcu_i2c0: i2c@4900000 {
@@ -32,6 +84,7 @@
 		power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 106 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	mcu_spi0: spi@4b00000 {
@@ -42,6 +95,7 @@
 		#size-cells = <0>;
 		power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 147 0>;
+		status = "disabled";
 	};
 
 	mcu_spi1: spi@4b10000 {
@@ -52,6 +106,7 @@
 		#size-cells = <0>;
 		power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 148 0>;
+		status = "disabled";
 	};
 
 	mcu_gpio_intr: interrupt-controller@4210000 {
@@ -81,4 +136,15 @@
 		clocks = <&k3_clks 79 0>;
 		clock-names = "gpio";
 	};
+
+	mcu_rti0: watchdog@4880000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x04880000 0x00 0x100>;
+		clocks = <&k3_clks 131 0>;
+		power-domains = <&k3_pds 131 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 131 0>;
+		assigned-clock-parents = <&k3_clks 131 2>;
+		/* Tightly coupled to M4F */
+		status = "reserved";
+	};
 };
diff --git a/arch/arm/dts/k3-am62-thermal.dtsi b/arch/arm/dts/k3-am62-thermal.dtsi
new file mode 100644
index 0000000000..a358757e26
--- /dev/null
+++ b/arch/arm/dts/k3-am62-thermal.dtsi
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/thermal/thermal.h>
+
+thermal_zones: thermal-zones {
+	main0_thermal: main0-thermal {
+		polling-delay-passive = <250>;	/* milliSeconds */
+		polling-delay = <500>;		/* milliSeconds */
+		thermal-sensors = <&wkup_vtm0 0>;
+
+		trips {
+			main0_crit: main0-crit {
+				temperature = <105000>;	/* milliCelsius */
+				hysteresis = <2000>;	/* milliCelsius */
+				type = "critical";
+			};
+		};
+	};
+
+	main1_thermal: main1-thermal {
+		polling-delay-passive = <250>;	/* milliSeconds */
+		polling-delay = <500>;		/* milliSeconds */
+		thermal-sensors = <&wkup_vtm0 1>;
+
+		trips {
+			main1_crit: main1-crit {
+				temperature = <105000>;	/* milliCelsius */
+				hysteresis = <2000>;	/* milliCelsius */
+				type = "critical";
+			};
+		};
+	};
+};
diff --git a/arch/arm/dts/k3-am62-wakeup.dtsi b/arch/arm/dts/k3-am62-wakeup.dtsi
index 4090134676..eae0528871 100644
--- a/arch/arm/dts/k3-am62-wakeup.dtsi
+++ b/arch/arm/dts/k3-am62-wakeup.dtsi
@@ -26,16 +26,47 @@
 		power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 114 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	wkup_i2c0: i2c@2b200000 {
 		compatible = "ti,am64-i2c", "ti,omap4-i2c";
-		reg = <0x00 0x02b200000 0x00 0x100>;
+		reg = <0x00 0x2b200000 0x00 0x100>;
 		interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 107 4>;
 		clock-names = "fck";
+		status = "disabled";
+	};
+
+	wkup_rtc0: rtc@2b1f0000 {
+		compatible = "ti,am62-rtc";
+		reg = <0x00 0x2b1f0000 0x00 0x100>;
+		interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 117 6> , <&k3_clks 117 0>;
+		clock-names = "vbus", "osc32k";
+		power-domains = <&k3_pds 117 TI_SCI_PD_EXCLUSIVE>;
+		wakeup-source;
+	};
+
+	wkup_rti0: watchdog@2b000000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x00 0x2b000000 0x00 0x100>;
+		clocks = <&k3_clks 132 0>;
+		power-domains = <&k3_pds 132 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 132 0>;
+		assigned-clock-parents = <&k3_clks 132 2>;
+		/* Used by DM firmware */
+		status = "reserved";
+	};
+
+	wkup_vtm0: temperature-sensor@b00000 {
+		compatible = "ti,j7200-vtm";
+		reg = <0x00 0xb00000 0x00 0x400>,
+		      <0x00 0xb01000 0x00 0x400>;
+		power-domains = <&k3_pds 95 TI_SCI_PD_EXCLUSIVE>;
+		#thermal-sensor-cells = <1>;
 	};
 };
diff --git a/arch/arm/dts/k3-am62.dtsi b/arch/arm/dts/k3-am62.dtsi
index 37fcbe7a3c..5e72c445f3 100644
--- a/arch/arm/dts/k3-am62.dtsi
+++ b/arch/arm/dts/k3-am62.dtsi
@@ -8,9 +8,10 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
 #include <dt-bindings/soc/ti,sci_pm_domain.h>
 
+#include "k3-pinctrl.h"
+
 / {
 	model = "Texas Instruments K3 AM625 SoC";
 	compatible = "ti,am625";
@@ -80,6 +81,7 @@
 			 <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>,
 
 			 /* Wakeup Domain Range */
+			 <0x00 0x00b00000 0x00 0x00b00000 0x00 0x00002400>, /* VTM */
 			 <0x00 0x2b000000 0x00 0x2b000000 0x00 0x00300400>,
 			 <0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>;
 
@@ -90,14 +92,17 @@
 			ranges = <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>; /* Peripheral window */
 		};
 
-		cbass_wakeup: bus@2b000000 {
+		cbass_wakeup: bus@b00000 {
 			compatible = "simple-bus";
 			#address-cells = <2>;
 			#size-cells = <2>;
-			ranges = <0x00 0x2b000000 0x00 0x2b000000 0x00 0x00300400>, /* Peripheral Window */
+			ranges = <0x00 0x00b00000 0x00 0x00b00000 0x00 0x00002400>, /* VTM */
+				 <0x00 0x2b000000 0x00 0x2b000000 0x00 0x00300400>, /* Peripheral Window */
 				 <0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>;
 		};
 	};
+
+	#include "k3-am62-thermal.dtsi"
 };
 
 /* Now include the peripherals for each bus segments */
diff --git a/arch/arm/dts/k3-am625-r5-sk.dts b/arch/arm/dts/k3-am625-r5-sk.dts
index 3ec5bad735..bf219226b9 100644
--- a/arch/arm/dts/k3-am625-r5-sk.dts
+++ b/arch/arm/dts/k3-am625-r5-sk.dts
@@ -9,7 +9,6 @@
 #include "k3-am62-ddr.dtsi"
 
 #include "k3-am625-sk-u-boot.dtsi"
-#include "k3-am625-sk-binman.dtsi"
 
 / {
 	aliases {
@@ -19,31 +18,6 @@
 		serial3 = &main_uart1;
 	};
 
-	chosen {
-		stdout-path = "serial2:115200n8";
-		tick-timer = &timer1;
-	};
-
-	memory@80000000 {
-		device_type = "memory";
-		/* 2G RAM */
-		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
-
-		bootph-pre-ram;
-	};
-
-	reserved-memory {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		secure_ddr: optee@9e800000 {
-			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
-			alignment = <0x1000>;
-			no-map;
-		};
-	};
-
 	a53_0: a53@0 {
 		compatible = "ti,am654-rproc";
 		reg = <0x00 0x00a90000 0x00 0x10>;
@@ -81,80 +55,44 @@
 	ti,secure-host;
 };
 
-&cbass_mcu {
-	mcu_esm: esm@4100000 {
-		compatible = "ti,j721e-esm";
-		reg = <0x0 0x4100000 0x0 0x1000>;
-		ti,esm-pins = <0>, <1>, <2>, <85>;
-		bootph-pre-ram;
-	};
+&mcu_esm {
+	bootph-pre-ram;
 };
 
-&cbass_main {
-	sa3_secproxy: secproxy@44880000 {
-		bootph-pre-ram;
-		compatible = "ti,am654-secure-proxy";
-		#mbox-cells = <1>;
-		reg-names = "rt", "scfg", "target_data";
-		reg = <0x00 0x44880000 0x00 0x20000>,
-		      <0x0 0x44860000 0x0 0x20000>,
-		      <0x0 0x43600000 0x0 0x10000>;
-	};
+&secure_proxy_sa3 {
+	bootph-pre-ram;
+	/* We require this for boot handshake */
+	status = "okay";
+};
+
+&main_esm {
+	bootph-pre-ram;
+};
 
+&cbass_main {
 	sysctrler: sysctrler {
 		compatible = "ti,am654-system-controller";
-		mboxes= <&secure_proxy_main 1>, <&secure_proxy_main 0>, <&sa3_secproxy 0>;
+		mboxes= <&secure_proxy_main 1>, <&secure_proxy_main 0>, <&secure_proxy_sa3 0>;
 		mbox-names = "tx", "rx", "boot_notify";
 		bootph-pre-ram;
 	};
-
-	main_esm: esm@420000 {
-		compatible = "ti,j721e-esm";
-		reg = <0x0 0x420000 0x0 0x1000>;
-		ti,esm-pins = <160>, <161>, <162>, <163>, <177>, <178>;
-		bootph-pre-ram;
-	};
 };
 
-&mcu_pmx0 {
+&wkup_uart0_pins_default {
 	bootph-pre-ram;
-	wkup_uart0_pins_default: wkup-uart0-pins-default {
-		pinctrl-single,pins = <
-			AM62X_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C6) WKUP_UART0_CTSn */
-			AM62X_MCU_IOPAD(0x030, PIN_OUTPUT, 0) /* (A4) WKUP_UART0_RTSn */
-			AM62X_MCU_IOPAD(0x024, PIN_INPUT, 0) /* (B4) WKUP_UART0_RXD */
-			AM62X_MCU_IOPAD(0x028, PIN_OUTPUT, 0) /* (C5) WKUP_UART0_TXD */
-		>;
-		bootph-pre-ram;
-	};
 };
 
-&main_pmx0 {
+&main_uart1_pins_default {
 	bootph-pre-ram;
-	main_uart1_pins_default: main-uart1-pins-default {
-		pinctrl-single,pins = <
-			AM62X_IOPAD(0x194, PIN_INPUT, 2) /* (B19) MCASP0_AXR3.UART1_CTSn */
-			AM62X_IOPAD(0x198, PIN_OUTPUT, 2) /* (A19) MCASP0_AXR2.UART1_RTSn */
-			AM62X_IOPAD(0x1ac, PIN_INPUT, 2) /* (E19) MCASP0_AFSR.UART1_RXD */
-			AM62X_IOPAD(0x1b0, PIN_OUTPUT, 2) /* (A20) MCASP0_ACLKR.UART1_TXD */
-		>;
-		bootph-pre-ram;
-	};
 };
 
 /* WKUP UART0 is used for DM firmware logs */
 &wkup_uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&wkup_uart0_pins_default>;
-	status = "okay";
 	bootph-pre-ram;
 };
 
 /* Main UART1 is used for TIFS firmware logs */
 &main_uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_uart1_pins_default>;
-	status = "okay";
 	bootph-pre-ram;
 };
 
diff --git a/arch/arm/dts/k3-am625-sk-u-boot.dtsi b/arch/arm/dts/k3-am625-sk-u-boot.dtsi
index a60c37f1db..c1685bc9ca 100644
--- a/arch/arm/dts/k3-am625-sk-u-boot.dtsi
+++ b/arch/arm/dts/k3-am625-sk-u-boot.dtsi
@@ -9,7 +9,7 @@
 / {
 	chosen {
 		stdout-path = "serial2:115200n8";
-		tick-timer = &timer1;
+		tick-timer = &main_timer0;
 	};
 
 	aliases {
@@ -21,16 +21,13 @@
 	};
 };
 
-&cbass_main{
+&cbass_main {
 	bootph-pre-ram;
+};
 
-	timer1: timer@2400000 {
-		compatible = "ti,omap5430-timer";
-		reg = <0x00 0x2400000 0x00 0x80>;
-		ti,timer-alwon;
-		clock-frequency = <25000000>;
-		bootph-pre-ram;
-	};
+&main_timer0 {
+	clock-frequency = <25000000>;
+	bootph-pre-ram;
 };
 
 &dmss {
@@ -77,10 +74,6 @@
 	bootph-pre-ram;
 };
 
-&main_uart1 {
-	bootph-pre-ram;
-};
-
 &cbass_mcu {
 	bootph-pre-ram;
 };
@@ -93,10 +86,6 @@
 	bootph-pre-ram;
 };
 
-&wkup_uart0 {
-	bootph-pre-ram;
-};
-
 &sdhci1 {
 	bootph-pre-ram;
 };
@@ -130,17 +119,7 @@
 };
 
 &cpsw3g {
-	reg = <0x0 0x8000000 0x0 0x200000>,
-	      <0x0 0x43000200 0x0 0x8>;
-	reg-names = "cpsw_nuss", "mac_efuse";
-	/delete-property/ ranges;
 	bootph-pre-ram;
-
-	cpsw-phy-sel@04044 {
-		compatible = "ti,am64-phy-gmii-sel";
-		reg = <0x0 0x00104044 0x0 0x8>;
-		bootph-pre-ram;
-	};
 };
 
 &cpsw_port1 {
diff --git a/arch/arm/dts/k3-am625-sk.dts b/arch/arm/dts/k3-am625-sk.dts
index af5617ff44..3f9ef4053a 100644
--- a/arch/arm/dts/k3-am625-sk.dts
+++ b/arch/arm/dts/k3-am625-sk.dts
@@ -7,28 +7,19 @@
 
 /dts-v1/;
 
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/net/ti-dp83867.h>
-#include "k3-am625.dtsi"
+#include "k3-am62x-sk-common.dtsi"
 
 / {
-	compatible =  "ti,am625-sk", "ti,am625";
+	compatible = "ti,am625-sk", "ti,am625";
 	model = "Texas Instruments AM625 SK";
 
-	aliases {
-		serial2 = &main_uart0;
-		mmc0 = &sdhci0;
-		mmc1 = &sdhci1;
-		mmc2 = &sdhci2;
-		spi0 = &ospi0;
-		ethernet0 = &cpsw_port1;
-		ethernet1 = &cpsw_port2;
-	};
-
-	chosen {
-		stdout-path = "serial2:115200n8";
-		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+	opp-table {
+		/* Add 1.4GHz OPP for am625-sk board. Requires VDD_CORE to be at 0.85V */
+		opp-1400000000 {
+			opp-hz = /bits/ 64 <1400000000>;
+			opp-supported-hw = <0x01 0x0004>;
+			clock-latency-ns = <6000000>;
+		};
 	};
 
 	memory@80000000 {
@@ -38,39 +29,6 @@
 
 	};
 
-	reserved-memory {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		ramoops@9ca00000 {
-			compatible = "ramoops";
-			reg = <0x00 0x9ca00000 0x00 0x00100000>;
-			record-size = <0x8000>;
-			console-size = <0x8000>;
-			ftrace-size = <0x00>;
-			pmsg-size = <0x8000>;
-		};
-
-		secure_tfa_ddr: tfa@9e780000 {
-			reg = <0x00 0x9e780000 0x00 0x80000>;
-			alignment = <0x1000>;
-			no-map;
-		};
-
-		secure_ddr: optee@9e800000 {
-			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
-			alignment = <0x1000>;
-			no-map;
-		};
-
-		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0x9db00000 0x00 0xc00000>;
-			no-map;
-		};
-	};
-
 	vmain_pd: regulator-0 {
 		/* TPS65988 PD CONTROLLER OUTPUT */
 		compatible = "regulator-fixed";
@@ -130,108 +88,20 @@
 			 <3300000 0x1>;
 	};
 
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&usr_led_pins_default>;
-
-		led-0 {
-			label = "am62-sk:green:heartbeat";
-			gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			function = LED_FUNCTION_HEARTBEAT;
-			default-state = "off";
-		};
+	vcc_1v8: regulator-5 {
+		/* output of TPS6282518DMQ */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3_sys>;
+		regulator-always-on;
+		regulator-boot-on;
 	};
 };
 
 &main_pmx0 {
-	main_uart0_pins_default: main-uart0-pins-default {
-		pinctrl-single,pins = <
-			AM62X_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
-			AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
-		>;
-	};
-
-	main_i2c0_pins_default: main-i2c0-pins-default {
-		pinctrl-single,pins = <
-			AM62X_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
-			AM62X_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
-		>;
-	};
-
-	main_i2c1_pins_default: main-i2c1-pins-default {
-		pinctrl-single,pins = <
-			AM62X_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
-			AM62X_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
-		>;
-	};
-
-	main_i2c2_pins_default: main-i2c2-pins-default {
-		pinctrl-single,pins = <
-			AM62X_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */
-			AM62X_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */
-		>;
-	};
-
-	main_mmc0_pins_default: main-mmc0-pins-default {
-		pinctrl-single,pins = <
-			AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
-			AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
-			AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
-			AM62X_IOPAD(0x210, PIN_INPUT, 0) /* (AA1) MMC0_DAT1 */
-			AM62X_IOPAD(0x20c, PIN_INPUT, 0) /* (AA3) MMC0_DAT2 */
-			AM62X_IOPAD(0x208, PIN_INPUT, 0) /* (Y4) MMC0_DAT3 */
-			AM62X_IOPAD(0x204, PIN_INPUT, 0) /* (AB2) MMC0_DAT4 */
-			AM62X_IOPAD(0x200, PIN_INPUT, 0) /* (AC1) MMC0_DAT5 */
-			AM62X_IOPAD(0x1fc, PIN_INPUT, 0) /* (AD2) MMC0_DAT6 */
-			AM62X_IOPAD(0x1f8, PIN_INPUT, 0) /* (AC2) MMC0_DAT7 */
-		>;
-	};
-
-	main_mmc1_pins_default: main-mmc1-pins-default {
-		pinctrl-single,pins = <
-			AM62X_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
-			AM62X_IOPAD(0x234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
-			AM62X_IOPAD(0x230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */
-			AM62X_IOPAD(0x22c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */
-			AM62X_IOPAD(0x228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
-			AM62X_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
-			AM62X_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */
-		>;
-	};
-
-	usr_led_pins_default: usr-led-pins-default {
-		pinctrl-single,pins = <
-			AM62X_IOPAD(0x244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
-		>;
-	};
-
-	main_mdio1_pins_default: main-mdio1-pins-default {
-		pinctrl-single,pins = <
-			AM62X_IOPAD(0x160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
-			AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
-		>;
-	};
-
-	main_rgmii1_pins_default: main-rgmii1-pins-default {
-		pinctrl-single,pins = <
-			AM62X_IOPAD(0x14c, PIN_INPUT, 0) /* (AB17) RGMII1_RD0 */
-			AM62X_IOPAD(0x150, PIN_INPUT, 0) /* (AC17) RGMII1_RD1 */
-			AM62X_IOPAD(0x154, PIN_INPUT, 0) /* (AB16) RGMII1_RD2 */
-			AM62X_IOPAD(0x158, PIN_INPUT, 0) /* (AA15) RGMII1_RD3 */
-			AM62X_IOPAD(0x148, PIN_INPUT, 0) /* (AD17) RGMII1_RXC */
-			AM62X_IOPAD(0x144, PIN_INPUT, 0) /* (AE17) RGMII1_RX_CTL */
-			AM62X_IOPAD(0x134, PIN_OUTPUT, 0) /* (AE20) RGMII1_TD0 */
-			AM62X_IOPAD(0x138, PIN_OUTPUT, 0) /* (AD20) RGMII1_TD1 */
-			AM62X_IOPAD(0x13c, PIN_OUTPUT, 0) /* (AE18) RGMII1_TD2 */
-			AM62X_IOPAD(0x140, PIN_OUTPUT, 0) /* (AD18) RGMII1_TD3 */
-			AM62X_IOPAD(0x130, PIN_OUTPUT, 0) /* (AE19) RGMII1_TXC */
-			AM62X_IOPAD(0x12c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */
-		>;
-	};
-
-	main_rgmii2_pins_default: main-rgmii2-pins-default {
+	main_rgmii2_pins_default: main-rgmii2-default-pins {
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
 			AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
@@ -248,7 +118,7 @@
 		>;
 	};
 
-	ospi0_pins_default: ospi0-pins-default {
+	ospi0_pins_default: ospi0-default-pins {
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
 			AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
@@ -264,77 +134,20 @@
 		>;
 	};
 
-	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+	vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (P25) GPMC0_CLK.GPIO0_31 */
 		>;
 	};
 
-	main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-pins-default {
+	main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
 		pinctrl-single,pins = <
 			AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
 		>;
 	};
 };
 
-&wkup_uart0 {
-	/* WKUP UART0 is used by DM firmware */
-	status = "reserved";
-};
-
-&mcu_uart0 {
-	status = "disabled";
-};
-
-&main_uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_uart0_pins_default>;
-};
-
-&main_uart1 {
-	/* Main UART1 is used by TIFS firmware */
-	status = "reserved";
-};
-
-&main_uart2 {
-	status = "disabled";
-};
-
-&main_uart3 {
-	status = "disabled";
-};
-
-&main_uart4 {
-	status = "disabled";
-};
-
-&main_uart5 {
-	status = "disabled";
-};
-
-&main_uart6 {
-	status = "disabled";
-};
-
-&mcu_i2c0 {
-	status = "disabled";
-};
-
-&wkup_i2c0 {
-	status = "disabled";
-};
-
-&main_i2c0 {
-	status = "disabled";
-	pinctrl-0 = <&main_i2c0_pins_default>;
-	clock-frequency = <400000>;
-};
-
 &main_i2c1 {
-	status = "disabled";
-	pinctrl-0 = <&main_i2c1_pins_default>;
-	clock-frequency = <400000>;
-
 	exp1: gpio@22 {
 		compatible = "ti,tca6424";
 		reg = <0x22>;
@@ -348,7 +161,7 @@
 				   "UART1_FET_BUF_EN", "WL_LT_EN",
 				   "GPIO_HDMI_RSTn", "CSI_GPIO1",
 				   "CSI_GPIO2", "PRU_3V3_EN",
-				   "HDMI_INTn", "TEST_GPIO2",
+				   "HDMI_INTn", "PD_I2C_IRQ",
 				   "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
 				   "MCASP1_FET_SEL", "UART1_FET_SEL",
 				   "TSINT#", "IO_EXP_TEST_LED";
@@ -363,41 +176,14 @@
 	};
 };
 
-&main_i2c2 {
-	status = "disabled";
-};
-
-&main_i2c3 {
-	status = "disabled";
-};
-
-&sdhci0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_mmc0_pins_default>;
-	ti,driver-strength-ohm = <50>;
-	disable-wp;
-};
-
 &sdhci1 {
-	/* SD/MMC */
 	vmmc-supply = <&vdd_mmc1>;
 	vqmmc-supply = <&vdd_sd_dv>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_mmc1_pins_default>;
-	ti,driver-strength-ohm = <50>;
-	disable-wp;
 };
 
 &cpsw3g {
 	pinctrl-names = "default";
-	pinctrl-0 = <&main_mdio1_pins_default
-		     &main_rgmii1_pins_default
-		     &main_rgmii2_pins_default>;
-};
-
-&cpsw_port1 {
-	phy-mode = "rgmii-rxid";
-	phy-handle = <&cpsw3g_phy0>;
+	pinctrl-0 = <&main_rgmii1_pins_default>, <&main_rgmii2_pins_default>;
 };
 
 &cpsw_port2 {
@@ -406,13 +192,6 @@
 };
 
 &cpsw3g_mdio {
-	cpsw3g_phy0: ethernet-phy@0 {
-		reg = <0>;
-		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
-		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
-		ti,min-output-impedance;
-	};
-
 	cpsw3g_phy1: ethernet-phy@1 {
 		reg = <1>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
@@ -429,6 +208,7 @@
 };
 
 &ospi0 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&ospi0_pins_default>;
 
@@ -487,18 +267,6 @@
 	};
 };
 
-&ecap0 {
-	status = "disabled";
-};
-
-&ecap1 {
-	status = "disabled";
-};
-
-&ecap2 {
-	status = "disabled";
-};
-
-&main_mcan0 {
-	status = "disabled";
+&tlv320aic3106 {
+	DVDD-supply = <&vcc_1v8>;
 };
diff --git a/arch/arm/dts/k3-am625.dtsi b/arch/arm/dts/k3-am625.dtsi
index 887f31c23f..4193c2b3ee 100644
--- a/arch/arm/dts/k3-am625.dtsi
+++ b/arch/arm/dts/k3-am625.dtsi
@@ -48,6 +48,8 @@
 			d-cache-line-size = <64>;
 			d-cache-sets = <128>;
 			next-level-cache = <&L2_0>;
+			operating-points-v2 = <&a53_opp_table>;
+			clocks = <&k3_clks 135 0>;
 		};
 
 		cpu1: cpu@1 {
@@ -62,6 +64,8 @@
 			d-cache-line-size = <64>;
 			d-cache-sets = <128>;
 			next-level-cache = <&L2_0>;
+			operating-points-v2 = <&a53_opp_table>;
+			clocks = <&k3_clks 136 0>;
 		};
 
 		cpu2: cpu@2 {
@@ -76,6 +80,8 @@
 			d-cache-line-size = <64>;
 			d-cache-sets = <128>;
 			next-level-cache = <&L2_0>;
+			operating-points-v2 = <&a53_opp_table>;
+			clocks = <&k3_clks 137 0>;
 		};
 
 		cpu3: cpu@3 {
@@ -90,13 +96,59 @@
 			d-cache-line-size = <64>;
 			d-cache-sets = <128>;
 			next-level-cache = <&L2_0>;
+			operating-points-v2 = <&a53_opp_table>;
+			clocks = <&k3_clks 138 0>;
+		};
+	};
+
+	a53_opp_table: opp-table {
+		compatible = "operating-points-v2-ti-cpu";
+		opp-shared;
+		syscon = <&wkup_conf>;
+
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-supported-hw = <0x01 0x0007>;
+			clock-latency-ns = <6000000>;
+		};
+
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x01 0x0007>;
+			clock-latency-ns = <6000000>;
+		};
+
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x01 0x0007>;
+			clock-latency-ns = <6000000>;
+		};
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-supported-hw = <0x01 0x0007>;
+			clock-latency-ns = <6000000>;
+		};
+
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-supported-hw = <0x01 0x0006>;
+			clock-latency-ns = <6000000>;
+		};
+
+		opp-1250000000 {
+			opp-hz = /bits/ 64 <1250000000>;
+			opp-supported-hw = <0x01 0x0004>;
+			clock-latency-ns = <6000000>;
+			opp-suspend;
 		};
 	};
 
 	L2_0: l2-cache0 {
 		compatible = "cache";
+		cache-unified;
 		cache-level = <2>;
-		cache-size = <0x40000>;
+		cache-size = <0x80000>;
 		cache-line-size = <64>;
 		cache-sets = <512>;
 	};
diff --git a/arch/arm/dts/k3-am62x-sk-common.dtsi b/arch/arm/dts/k3-am62x-sk-common.dtsi
new file mode 100644
index 0000000000..34c8ffc553
--- /dev/null
+++ b/arch/arm/dts/k3-am62x-sk-common.dtsi
@@ -0,0 +1,412 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Common dtsi for AM62x SK and derivatives
+ *
+ * Copyright (C) 2021-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "k3-am625.dtsi"
+
+/ {
+	aliases {
+		serial2 = &main_uart0;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		mmc2 = &sdhci2;
+		spi0 = &ospi0;
+		ethernet0 = &cpsw_port1;
+		ethernet1 = &cpsw_port2;
+		usb0 = &usb0;
+		usb1 = &usb1;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* 2G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@9ca00000 {
+			compatible = "ramoops";
+			reg = <0x00 0x9ca00000 0x00 0x00100000>;
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x00>;
+			pmsg-size = <0x8000>;
+		};
+
+		secure_tfa_ddr: tfa@9e780000 {
+			reg = <0x00 0x9e780000 0x00 0x80000>;
+			alignment = <0x1000>;
+			no-map;
+		};
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+			alignment = <0x1000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9db00000 0x00 0xc00000>;
+			no-map;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usr_led_pins_default>;
+
+		led-0 {
+			label = "am62-sk:green:heartbeat";
+			gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+			default-state = "off";
+		};
+	};
+
+	tlv320_mclk: clk-0 {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12288000>;
+	};
+
+	codec_audio: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "AM62x-SKEVM";
+		simple-audio-card,widgets =
+			"Headphone",	"Headphone Jack",
+			"Line",		"Line In",
+			"Microphone",	"Microphone Jack";
+		simple-audio-card,routing =
+			"Headphone Jack",	"HPLOUT",
+			"Headphone Jack",	"HPROUT",
+			"LINE1L",		"Line In",
+			"LINE1R",		"Line In",
+			"MIC3R",		"Microphone Jack",
+			"Microphone Jack",	"Mic Bias";
+		simple-audio-card,format = "dsp_b";
+		simple-audio-card,bitclock-master = <&sound_master>;
+		simple-audio-card,frame-master = <&sound_master>;
+		simple-audio-card,bitclock-inversion;
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcasp1>;
+		};
+
+		sound_master: simple-audio-card,codec {
+			sound-dai = <&tlv320aic3106>;
+			clocks = <&tlv320_mclk>;
+		};
+	};
+};
+
+&main_pmx0 {
+	/* First pad number is ALW package and second is AMC package */
+	main_uart0_pins_default: main-uart0-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14/A13) UART0_RXD */
+			AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14/E11) UART0_TXD */
+		>;
+	};
+
+	main_uart1_pins_default: main-uart1-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x194, PIN_INPUT, 2) /* (B19/B18) MCASP0_AXR3.UART1_CTSn */
+			AM62X_IOPAD(0x198, PIN_OUTPUT, 2) /* (A19/B17) MCASP0_AXR2.UART1_RTSn */
+			AM62X_IOPAD(0x1ac, PIN_INPUT, 2) /* (E19/D15) MCASP0_AFSR.UART1_RXD */
+			AM62X_IOPAD(0x1b0, PIN_OUTPUT, 2) /* (A20/D16) MCASP0_ACLKR.UART1_TXD */
+		>;
+	};
+
+	main_i2c0_pins_default: main-i2c0-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16/E12) I2C0_SCL */
+			AM62X_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16/D14) I2C0_SDA */
+		>;
+	};
+
+	main_i2c1_pins_default: main-i2c1-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17/A17) I2C1_SCL */
+			AM62X_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17/A16) I2C1_SDA */
+		>;
+	};
+
+	main_i2c2_pins_default: main-i2c2-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22/H18) GPMC0_CSn2.I2C2_SCL */
+			AM62X_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24/H19) GPMC0_CSn3.I2C2_SDA */
+		>;
+	};
+
+	main_mmc0_pins_default: main-mmc0-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3/V3) MMC0_CMD */
+			AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1/Y1) MMC0_CLK */
+			AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2/V2) MMC0_DAT0 */
+			AM62X_IOPAD(0x210, PIN_INPUT, 0) /* (AA1/V1) MMC0_DAT1 */
+			AM62X_IOPAD(0x20c, PIN_INPUT, 0) /* (AA3/W2) MMC0_DAT2 */
+			AM62X_IOPAD(0x208, PIN_INPUT, 0) /* (Y4/W1) MMC0_DAT3 */
+			AM62X_IOPAD(0x204, PIN_INPUT, 0) /* (AB2/Y2) MMC0_DAT4 */
+			AM62X_IOPAD(0x200, PIN_INPUT, 0) /* (AC1/W3) MMC0_DAT5 */
+			AM62X_IOPAD(0x1fc, PIN_INPUT, 0) /* (AD2/W4) MMC0_DAT6 */
+			AM62X_IOPAD(0x1f8, PIN_INPUT, 0) /* (AC2/V4) MMC0_DAT7 */
+		>;
+	};
+
+	main_mmc1_pins_default: main-mmc1-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x23c, PIN_INPUT, 0) /* (A21/C18) MMC1_CMD */
+			AM62X_IOPAD(0x234, PIN_INPUT, 0) /* (B22/A20) MMC1_CLK */
+			AM62X_IOPAD(0x230, PIN_INPUT, 0) /* (A22/A19) MMC1_DAT0 */
+			AM62X_IOPAD(0x22c, PIN_INPUT, 0) /* (B21/B19) MMC1_DAT1 */
+			AM62X_IOPAD(0x228, PIN_INPUT, 0) /* (C21/B20) MMC1_DAT2 */
+			AM62X_IOPAD(0x224, PIN_INPUT, 0) /* (D22/C19) MMC1_DAT3 */
+			AM62X_IOPAD(0x240, PIN_INPUT, 0) /* (D17/C15) MMC1_SDCD */
+		>;
+	};
+
+	usr_led_pins_default: usr-led-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x244, PIN_OUTPUT, 7) /* (C17/B15) MMC1_SDWP.GPIO1_49 */
+		>;
+	};
+
+	main_mdio1_pins_default: main-mdio1-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x160, PIN_OUTPUT, 0) /* (AD24/V17) MDIO0_MDC */
+			AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22/U16) MDIO0_MDIO */
+		>;
+	};
+
+	main_rgmii1_pins_default: main-rgmii1-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x14c, PIN_INPUT, 0) /* (AB17/W15) RGMII1_RD0 */
+			AM62X_IOPAD(0x150, PIN_INPUT, 0) /* (AC17/Y16) RGMII1_RD1 */
+			AM62X_IOPAD(0x154, PIN_INPUT, 0) /* (AB16/AA17) RGMII1_RD2 */
+			AM62X_IOPAD(0x158, PIN_INPUT, 0) /* (AA15/Y15) RGMII1_RD3 */
+			AM62X_IOPAD(0x148, PIN_INPUT, 0) /* (AD17/AA16) RGMII1_RXC */
+			AM62X_IOPAD(0x144, PIN_INPUT, 0) /* (AE17/W14) RGMII1_RX_CTL */
+			AM62X_IOPAD(0x134, PIN_OUTPUT, 0) /* (AE20/U14) RGMII1_TD0 */
+			AM62X_IOPAD(0x138, PIN_OUTPUT, 0) /* (AD20/AA19) RGMII1_TD1 */
+			AM62X_IOPAD(0x13c, PIN_OUTPUT, 0) /* (AE18/Y17) RGMII1_TD2 */
+			AM62X_IOPAD(0x140, PIN_OUTPUT, 0) /* (AD18/AA18) RGMII1_TD3 */
+			AM62X_IOPAD(0x130, PIN_OUTPUT, 0) /* (AE19/W16) RGMII1_TXC */
+			AM62X_IOPAD(0x12c, PIN_OUTPUT, 0) /* (AD19/V15) RGMII1_TX_CTL */
+		>;
+	};
+
+	main_usb1_pins_default: main-usb1-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18/E16) USB1_DRVVBUS */
+		>;
+	};
+
+	main_mcasp1_pins_default: main-mcasp1-default-pins {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x090, PIN_INPUT, 2) /* (M24/K17) GPMC0_BE0N_CLE.MCASP1_ACLKX */
+			AM62X_IOPAD(0x098, PIN_INPUT, 2) /* (U23/P21) GPMC0_WAIT0.MCASP1_AFSX */
+			AM62X_IOPAD(0x08c, PIN_OUTPUT, 2) /* (L25/J17) GPMC0_WEN.MCASP1_AXR0 */
+			AM62X_IOPAD(0x084, PIN_INPUT, 2) /* (L23/K20) GPMC0_ADVN_ALE.MCASP1_AXR2 */
+		>;
+	};
+};
+
+&mcu_pmx0 {
+	wkup_uart0_pins_default: wkup-uart0-default-pins {
+		pinctrl-single,pins = <
+			AM62X_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C6/A7) WKUP_UART0_CTSn */
+			AM62X_MCU_IOPAD(0x030, PIN_OUTPUT, 0) /* (A4/B4) WKUP_UART0_RTSn */
+			AM62X_MCU_IOPAD(0x024, PIN_INPUT, 0) /* (B4/B5) WKUP_UART0_RXD */
+			AM62X_MCU_IOPAD(0x028, PIN_OUTPUT, 0) /* (C5/C6) WKUP_UART0_TXD */
+		>;
+	};
+};
+
+&wkup_uart0 {
+	/* WKUP UART0 is used by DM firmware */
+	status = "reserved";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_uart0_pins_default>;
+};
+
+&main_uart0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+};
+
+&main_uart1 {
+	/* Main UART1 is used by TIFS firmware */
+	status = "reserved";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart1_pins_default>;
+};
+
+&main_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	eeprom@51 {
+		/* AT24C512C-MAHM-T or M24512-DFMC6TG */
+		compatible = "atmel,24c512";
+		reg = <0x51>;
+	};
+
+	typec_pd0: tps6598x@3f {
+		compatible = "ti,tps6598x";
+		reg = <0x3f>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			self-powered;
+			data-role = "dual";
+			power-role = "sink";
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					usb_con_hs: endpoint {
+						remote-endpoint = <&usb0_hs_ep>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&main_i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c1_pins_default>;
+	clock-frequency = <400000>;
+
+	tlv320aic3106: audio-codec@1b {
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		ai3x-micbias-vg = <1>;	/* 2.0V */
+
+		/* Regulators */
+		AVDD-supply = <&vcc_3v3_sys>;
+		IOVDD-supply = <&vcc_3v3_sys>;
+		DRVDD-supply = <&vcc_3v3_sys>;
+	};
+};
+
+&sdhci0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc0_pins_default>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&sdhci1 {
+	/* SD/MMC */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&cpsw3g {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_rgmii1_pins_default>;
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw3g_mdio {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mdio1_pins_default>;
+
+	cpsw3g_phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
+
+&mailbox0_cluster0 {
+	mbox_m4_0: mbox-m4-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
+&usbss0 {
+	status = "okay";
+	ti,vbus-divider;
+};
+
+&usbss1 {
+	status = "okay";
+	ti,vbus-divider;
+};
+
+&usb0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	usb-role-switch;
+
+	port@0 {
+		reg = <0>;
+		usb0_hs_ep: endpoint {
+		    remote-endpoint = <&usb_con_hs>;
+	       };
+	};
+};
+
+&usb1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usb1_pins_default>;
+};
+
+&mcasp1 {
+	status = "okay";
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcasp1_pins_default>;
+
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+	       1 0 2 0
+	       0 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};
diff --git a/arch/arm/dts/k3-pinctrl.h b/arch/arm/dts/k3-pinctrl.h
new file mode 100644
index 0000000000..c97548a3f4
--- /dev/null
+++ b/arch/arm/dts/k3-pinctrl.h
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides constants for pinctrl bindings for TI's K3 SoC
+ * family.
+ *
+ * Copyright (C) 2018-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+#ifndef DTS_ARM64_TI_K3_PINCTRL_H
+#define DTS_ARM64_TI_K3_PINCTRL_H
+
+#define PULLUDEN_SHIFT		(16)
+#define PULLTYPESEL_SHIFT	(17)
+#define RXACTIVE_SHIFT		(18)
+
+#define PULL_DISABLE		(1 << PULLUDEN_SHIFT)
+#define PULL_ENABLE		(0 << PULLUDEN_SHIFT)
+
+#define PULL_UP			(1 << PULLTYPESEL_SHIFT | PULL_ENABLE)
+#define PULL_DOWN		(0 << PULLTYPESEL_SHIFT | PULL_ENABLE)
+
+#define INPUT_EN		(1 << RXACTIVE_SHIFT)
+#define INPUT_DISABLE		(0 << RXACTIVE_SHIFT)
+
+/* Only these macros are expected be used directly in device tree files */
+#define PIN_OUTPUT		(INPUT_DISABLE | PULL_DISABLE)
+#define PIN_OUTPUT_PULLUP	(INPUT_DISABLE | PULL_UP)
+#define PIN_OUTPUT_PULLDOWN	(INPUT_DISABLE | PULL_DOWN)
+#define PIN_INPUT		(INPUT_EN | PULL_DISABLE)
+#define PIN_INPUT_PULLUP	(INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN	(INPUT_EN | PULL_DOWN)
+
+#define AM62AX_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM62AX_MCU_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define AM62X_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM62X_MCU_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define AM64X_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM64X_MCU_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define AM65X_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM65X_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define J721E_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define J721E_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define J721S2_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define J721S2_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define J784S4_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define J784S4_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
+#endif