| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
I have observed that the current size of 8M gives us pretty poor
fragmentation on multi-threaded workloads which do lots of writes.
Generally, I can increase the size of local alloc windows and observe a
marked decrease in fragmentation, even up and beyond window sizes of 512
megabytes. This makes sense for a couple reasons - larger local alloc means
more room for reservation windows. On multi-node workloads the larger local
alloc helps as well because we don't have to do window slides as often.
Also, I removed the OCFS2_DEFAULT_LOCAL_ALLOC_SIZE constant as it is no
longer used and the comment above it was out of date.
To test fragmentation, I used a workload which launched 4 threads that did
4k writes into a series of about 140 alternating files.
With resv_level=2, and a 4k/4k file system I observed the following average
fragmentation for various localalloc= parameters:
localalloc= avg. fragmentation
8 48
32 16
64 10
120 7
On larger cluster sizes, the difference is more dramatic.
The new default size top out at 256M, which we'll only get for cluster
sizes of 32K and above.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
This patch pulls the local alloc sizing code into localalloc.c and provides
a callout to it from ocfs2_fill_super(). Behavior is essentially unchanged
except that I correctly calculate the maximum local alloc size. The old code
in ocfs2_parse_options() calculated the max size as:
ocfs2_local_alloc_size(sb) * 8
which is correct, in bits. Unfortunately though the option passed in is in
megabytes. Ultimately, this bug made no real difference - the shrink code
would catch a too-large size and bring it down to something reasonable.
Still, it's less than efficient as-is.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
|
|
Ocfs2's local allocator disables itself for the duration of a mount point
when it has trouble allocating a large enough area from the primary bitmap.
That can cause performance problems, especially for disks which were only
temporarily full or fragmented. This patch allows for the allocator to
shrink it's window first, before being disabled. Later, it can also be
re-enabled so that any performance drop is minimized.
To do this, we allow the value of osb->local_alloc_bits to be shrunk when
needed. The default value is recorded in a mostly read-only variable so that
we can re-initialize when required.
Locking had to be updated so that we could protect changes to
local_alloc_bits. Mostly this involves protecting various local alloc values
with the osb spinlock. A new state is also added, OCFS2_LA_THROTTLED, which
is used when the local allocator is has shrunk, but is not disabled. If the
available space dips below 1 megabyte, the local alloc file is disabled. In
either case, local alloc is re-enabled 30 seconds after the event, or when
an appropriate amount of bits is seen in the primary bitmap.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
|
|
The ocfs2 write code loops through a page much like the block code, except
that ocfs2 allocation units can be any size, including larger than page
size. Typically it's equal to or larger than page size - most kernels run 4k
pages, the minimum ocfs2 allocation (cluster) size.
Some changes introduced during 2.6.23 changed the way writes to pages are
handled, and inadvertantly broke support for > 4k page size. Instead of just
writing one cluster at a time, we now handle the whole page in one pass.
This means that multiple (small) seperate allocations might happen in the
same pass. The allocation code howver typically optimizes by getting the
maximum which was reserved. This triggered a BUG_ON in the extend code where
it'd ask for a single bit (for one part of a > 4k page) and get back more
than it asked for.
Fix this by providing a variant of the high level allocation function which
allows the caller to specify a maximum. The traditional function remains and
just calls the new one with a maximum determined from the initial
reservation.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
This is mostly a search and replace as ocfs2_journal_handle is now no more
than a container for a handle_t pointer.
ocfs2_commit_trans() becomes very straight forward, and we remove some out
of date comments / code.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
Instead we record our state on the allocation context structure which all
callers already know about and lifetime correctly. This means the
reservation functions don't need a handle passed in any more, and we can
also take it off the alloc context.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
The OCFS2 file system module.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com>
|
