From c7cc9ba11f8c09a4d12af0fc4aa9f9b026cdd354 Mon Sep 17 00:00:00 2001 From: Lokesh Vutla Date: Thu, 4 Sep 2014 08:23:28 -0500 Subject: ARM: dts: dra7-evm: Add vtt regulator support DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination and this is controlled by gpio7_11. This gpio is configured in boot loader. gpio7_11, which is only available only on Pad A22, in previous boards, is connected only to an unused pad on expansion connector EXP_P3 and is safe to be muxed as GPIO on all DRA7-evm versions (without a need to spin off another dts file). Since gpio7_11 is used to control VTT and should not be reset or kept in idle state during boot up else VTT will be disconnected and DDR gets corrupted. So, as part of this change, mark gpio7 as no-reset and no-idle on init. Signed-off-by: Lokesh Vutla Signed-off-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7-evm.dts | 27 ++++++++++++++++++++++++++- 1 file changed, 26 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index b80c67b6fe01..e03fbf3c6889 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -8,6 +8,7 @@ /dts-v1/; #include "dra74x.dtsi" +#include / { model = "TI DRA742"; @@ -24,9 +25,29 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + + vtt_fixed: fixedregulator-vtt { + compatible = "regulator-fixed"; + regulator-name = "vtt_fixed"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + enable-active-high; + gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>; + }; }; &dra7_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = <&vtt_pin>; + + vtt_pin: pinmux_vtt_pin { + pinctrl-single,pins = < + 0x3b4 (PIN_OUTPUT | MUX_MODE14) /* spi1_cs1.gpio7_11 */ + >; + }; + i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < 0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */ @@ -54,7 +75,6 @@ 0x3a8 (PIN_INPUT | MUX_MODE0) /* spi1_d1 */ 0x3ac (PIN_INPUT | MUX_MODE0) /* spi1_d0 */ 0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */ - 0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs1 */ 0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */ 0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */ >; @@ -504,3 +524,8 @@ &usb2_phy2 { phy-supply = <&ldousb_reg>; }; + +&gpio7 { + ti,no-reset-on-init; + ti,no-idle-on-init; +}; -- cgit v1.2.3