summaryrefslogtreecommitdiff
path: root/drivers/mmc
AgeCommit message (Collapse)AuthorFilesLines
2019-04-11mmc: sdhci-omap: Don't finish_mrq() on a command error during tuningFaiz Abbas1-0/+38
commit 5b0d62108b46 ("mmc: sdhci-omap: Add platform specific reset callback") skips data resets during tuning operation. Because of this, a data error or data finish interrupt might still arrive after a command error has been handled and the mrq ended. This ends up with a "mmc0: Got data interrupt 0x00000002 even though no data operation was in progress" error message. Fix this by adding a platform specific callback for sdhci_irq. Mark the mrq as a failure but wait for a data interrupt instead of calling finish_mrq(). Fixes: 5b0d62108b46 ("mmc: sdhci-omap: Add platform specific reset callback") Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-28mmc: alcor: don't write data before command has completedDaniel Drake1-21/+13
The alcor driver is setting up data transfer and submitting the associated MMC command at the same time. While this works most of the time, it occasionally causes problems upon write. In the working case, after setting up the data transfer and submitting the MMC command, an interrupt comes in a moment later with CMD_END and WRITE_BUF_RDY bits set. The data transfer then happens without problem. However, on occasion, the interrupt that arrives at that point only has WRITE_BUF_RDY set. The hardware notifies that it's ready to write data, but the associated MMC command is still running. Regardless, the driver was proceeding to write data immediately, and that would then cause another interrupt indicating data CRC error, and the write would fail. Additionally, the transfer setup function alcor_trigger_data_transfer() was being called 3 times for each write operation, which was confusing and may be contributing to this issue. Solve this by tweaking the driver behaviour to follow the sequence observed in the original ampe_stor vendor driver: 1. When starting request handling, write 0 to DATA_XFER_CTRL 2. Submit the command 3. Wait for CMD_END interrupt and then trigger data transfer 4. For the PIO case, trigger the next step of the data transfer only upon the following DATA_END interrupt, which occurs after the block has been written. I confirmed that the read path still works (DMA & PIO) and also now presents more consistency with the operations performed by ampe_stor. Signed-off-by: Daniel Drake <drake@endlessm.com> Fixes: c5413ad815a6 ("mmc: add new Alcor Micro Cardreader SD/MMC driver") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-21mmc: renesas_sdhi: limit block count to 16 bit for old revisionsWolfram Sang1-1/+7
R-Car Gen2 has two different SDHI incarnations in the same chip. The older one does not support the recently introduced 32 bit register access to the block count register. Make sure we use this feature only after the first known version. Thanks to the Renesas Testing team for this bug report! Fixes: 5603731a15ef ("mmc: tmio: fix access width of Block Count Register") Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Tested-by: Phong Hoang <phong.hoang.wz@renesas.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-21mmc: alcor: fix DMA readsDaniel Drake1-6/+19
Setting max_blk_count to 1 here was causing the mmc block layer to always use the MMC_READ_SINGLE_BLOCK command here, which the driver does not DMA-accelerate. Drop the max_blk_ settings here. The mmc host defaults suffice, along with the max_segs and max_seg_size settings, which I have now documented in more detail. Now each MMC command reads 4 512-byte blocks, using DMA instead of PIO. On my SD card, this increases read performance (measured with dd) from 167kb/sec to 4.6mb/sec. Link: http://lkml.kernel.org/r/CAD8Lp47L5T3jnAjBiPs1cQ+yFA3L6LJtgFvMETnBrY63-Zdi2g@mail.gmail.com Signed-off-by: Daniel Drake <drake@endlessm.com> Reviewed-by: Oleksij Rempel <linux@rempel-privat.de> Fixes: c5413ad815a6 ("mmc: add new Alcor Micro Cardreader SD/MMC driver") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-21mmc: sdhci-omap: Set caps2 to indicate no physical write protect pinKishon Vijay Abraham I1-0/+3
After commit 6d5cd068ee59fba ("mmc: sdhci: use WP GPIO in sdhci_check_ro()") and commit 39ee32ce486756f ("mmc: sdhci-omap: drop ->get_ro() implementation"), sdhci-omap relied on SDHCI_PRESENT_STATE to check if the card is read-only, if wp-gpios is not populated in device tree. However SDHCI_PRESENT_STATE in sdhci-omap does not have correct read-only state. sdhci-omap can be used by platforms with both micro SD slot and standard SD slot with physical write protect pin (using GPIO). Set caps2 to MMC_CAP2_NO_WRITE_PROTECT based on if wp-gpios property is populated or not. This fix is required since existing device-tree node doesn't have "disable-wp" property and to preserve old-dt compatibility. Fixes: 6d5cd068ee59fba ("mmc: sdhci: use WP GPIO in sdhci_check_ro()") Fixes: 39ee32ce486756f ("mmc: sdhci-omap: drop ->get_ro() implementation") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-21mmc: mxcmmc: "Revert mmc: mxcmmc: handle highmem pages"Alexander Shiyan1-12/+4
This reverts commit b189e7589f6d3411e85c6b7ae6eef158f08f388f. Unable to handle kernel paging request at virtual address c8358000 pgd = efa405c3 [c8358000] *pgd=00000000 Internal error: Oops: 805 [#1] PREEMPT ARM CPU: 0 PID: 711 Comm: kworker/0:2 Not tainted 4.20.0+ #30 Hardware name: Freescale i.MX27 (Device Tree Support) Workqueue: events mxcmci_datawork PC is at mxcmci_datawork+0xbc/0x2ac LR is at mxcmci_datawork+0xac/0x2ac pc : [<c04e33c8>] lr : [<c04e33b8>] psr: 60000013 sp : c6c93f08 ip : 24004180 fp : 00000008 r10: c8358000 r9 : c78b3e24 r8 : c6c92000 r7 : 00000000 r6 : c7bb8680 r5 : c7bb86d4 r4 : c78b3de0 r3 : 00002502 r2 : c090b2e0 r1 : 00000880 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 0005317f Table: a68a8000 DAC: 00000055 Process kworker/0:2 (pid: 711, stack limit = 0x389543bc) Stack: (0xc6c93f08 to 0xc6c94000) 3f00: c7bb86d4 00000000 00000000 c6cbfde0 c7bb86d4 c7ee4200 3f20: 00000000 c0907ea8 00000000 c7bb86d8 c0907ea8 c012077c c6cbfde0 c7bb86d4 3f40: c6cbfde0 c6c92000 c6cbfdf4 c09280ba c0907ea8 c090b2e0 c0907ebc c0120c18 3f60: c6cbfde0 00000000 00000000 c6cbb580 c7ba7c40 c7837edc c6cbb598 00000000 3f80: c6cbfde0 c01208f8 00000000 c01254fc c7ba7c40 c0125400 00000000 00000000 3fa0: 00000000 00000000 00000000 c01010d0 00000000 00000000 00000000 00000000 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [<c04e33c8>] (mxcmci_datawork) from [<c012077c>] (process_one_work+0x1f0/0x338) [<c012077c>] (process_one_work) from [<c0120c18>] (worker_thread+0x320/0x474) [<c0120c18>] (worker_thread) from [<c01254fc>] (kthread+0xfc/0x118) [<c01254fc>] (kthread) from [<c01010d0>] (ret_from_fork+0x14/0x24) Exception stack(0xc6c93fb0 to 0xc6c93ff8) 3fa0: 00000000 00000000 00000000 00000000 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 Code: e3500000 1a000059 e5153050 e5933038 (e48a3004) ---[ end trace 54ca629b75f0e737 ]--- note: kworker/0:2[711] exited with preempt_count 1 Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Fixes: b189e7589f6d ("mmc: mxcmmc: handle highmem pages") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-18mmc: davinci: remove extraneous __init annotationArnd Bergmann1-1/+1
Building with clang finds a mistaken __init tag: WARNING: vmlinux.o(.text+0x5e4250): Section mismatch in reference from the function davinci_mmcsd_probe() to the function .init.text:init_mmcsd_host() The function davinci_mmcsd_probe() references the function __init init_mmcsd_host(). This is often because davinci_mmcsd_probe lacks a __init annotation or the annotation of init_mmcsd_host is wrong. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Wolfram Sang <wsa@the-dreams.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-18mmc: pxamci: fix enum type confusionArnd Bergmann1-1/+1
clang points out several instances of mismatched types in this drivers, all coming from a single declaration: drivers/mmc/host/pxamci.c:193:15: error: implicit conversion from enumeration type 'enum dma_transfer_direction' to different enumeration type 'enum dma_data_direction' [-Werror,-Wenum-conversion] direction = DMA_DEV_TO_MEM; ~ ^~~~~~~~~~~~~~ drivers/mmc/host/pxamci.c:212:62: error: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Werror,-Wenum-conversion] tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction, The behavior is correct, so this must be a simply typo from dma_data_direction and dma_transfer_direction being similarly named types with a similar purpose. Fixes: 6464b7140951 ("mmc: pxamci: switch over to dmaengine use") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-08Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-blockLinus Torvalds1-2/+1
Pull block layer updates from Jens Axboe: "Not a huge amount of changes in this round, the biggest one is that we finally have Mings multi-page bvec support merged. Apart from that, this pull request contains: - Small series that avoids quiescing the queue for sysfs changes that match what we currently have (Aleksei) - Series of bcache fixes (via Coly) - Series of lightnvm fixes (via Mathias) - NVMe pull request from Christoph. Nothing major, just SPDX/license cleanups, RR mp policy (Hannes), and little fixes (Bart, Chaitanya). - BFQ series (Paolo) - Save blk-mq cpu -> hw queue mapping, removing a pointer indirection for the fast path (Jianchao) - fops->iopoll() added for async IO polling, this is a feature that the upcoming io_uring interface will use (Christoph, me) - Partition scan loop fixes (Dongli) - mtip32xx conversion from managed resource API (Christoph) - cdrom registration race fix (Guenter) - MD pull from Song, two minor fixes. - Various documentation fixes (Marcos) - Multi-page bvec feature. This brings a lot of nice improvements with it, like more efficient splitting, larger IOs can be supported without growing the bvec table size, and so on. (Ming) - Various little fixes to core and drivers" * tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits) block: fix updating bio's front segment size block: Replace function name in string with __func__ nbd: propagate genlmsg_reply return code floppy: remove set but not used variable 'q' null_blk: fix checking for REQ_FUA block: fix NULL pointer dereference in register_disk fs: fix guard_bio_eod to check for real EOD errors blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map block: optimize bvec iteration in bvec_iter_advance block: introduce mp_bvec_for_each_page() for iterating over page block: optimize blk_bio_segment_split for single-page bvec block: optimize __blk_segment_map_sg() for single-page bvec block: introduce bvec_nth_page() iomap: wire up the iopoll method block: add bio_set_polled() helper block: wire up block device iopoll method fs: add an iopoll method to struct file_operations loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part() loop: do not print warn message if partition scan is successful block: bounce: make sure that bvec table is updated ...
2019-03-01mmc:fix a bug when max_discard is 0Jiong Wu1-2/+2
The original purpose of the code I fix is to replace max_discard with max_trim if max_trim is less than max_discard. When max_discard is 0 we should replace max_discard with max_trim as well, because max_discard equals 0 happens only when the max_do_calc_max_discard process is overflowed, so if mmc_can_trim(card) is true, max_discard should be replaced by an available max_trim. However, in the original code, there are two lines of code interfere the right process. 1) if (max_discard && mmc_can_trim(card)) when max_discard is 0, it skips the process checking if max_discard needs to be replaced with max_trim. 2) if (max_trim < max_discard) the condition is false when max_discard is 0. it also skips the process that replaces max_discard with max_trim, in fact, we should replace the 0-valued max_discard with max_trim. Signed-off-by: Jiong Wu <Lohengrin1024@gmail.com> Fixes: b305882fbc87 (mmc: core: optimize mmc_calc_max_discard) Cc: stable@vger.kernel.org # v4.17+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-28Merge branch 'fixes' into nextUlf Hansson1-4/+5
2019-02-28mmc: sdhci-esdhc-imx: correct the fix of ERR004536BOUGH CHEN1-4/+5
Commit 18094430d6b5 ("mmc: sdhci-esdhc-imx: add ADMA Length Mismatch errata fix") involve the fix of ERR004536, but the fix is incorrect. Double confirm with IC, need to clear the bit 7 of register 0x6c rather than set this bit 7. Here is the definition of bit 7 of 0x6c: 0: enable the new IC fix for ERR004536 1: do not use the IC fix, keep the same as before Find this issue on i.MX845s-evk board when enable CMDQ, and let system in heavy loading. root@imx8mmevk:~# dd if=/dev/mmcblk2 of=/dev/null bs=1M & root@imx8mmevk:~# memtester 1000M > /dev/zero & root@imx8mmevk:~# [ 139.897220] mmc2: cqhci: timeout for tag 16 [ 139.901417] mmc2: cqhci: ============ CQHCI REGISTER DUMP =========== [ 139.907862] mmc2: cqhci: Caps: 0x0000310a | Version: 0x00000510 [ 139.914311] mmc2: cqhci: Config: 0x00001001 | Control: 0x00000000 [ 139.920753] mmc2: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006 [ 139.927193] mmc2: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000 [ 139.933634] mmc2: cqhci: TDL base: 0x7809c000 | TDL up32: 0x00000000 [ 139.940073] mmc2: cqhci: Doorbell: 0x00030000 | TCN: 0x00000000 [ 139.946518] mmc2: cqhci: Dev queue: 0x00010000 | Dev Pend: 0x00010000 [ 139.952967] mmc2: cqhci: Task clr: 0x00000000 | SSC1: 0x00011000 [ 139.959411] mmc2: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000 [ 139.965857] mmc2: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000 [ 139.972308] mmc2: cqhci: Resp idx: 0x0000002e | Resp arg: 0x00000900 [ 139.978761] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== [ 139.985214] mmc2: sdhci: Sys addr: 0xb2c19000 | Version: 0x00000002 [ 139.991669] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000400 [ 139.998127] mmc2: sdhci: Argument: 0x40110400 | Trn mode: 0x00000033 [ 140.004618] mmc2: sdhci: Present: 0x01088a8f | Host ctl: 0x00000030 [ 140.011113] mmc2: sdhci: Power: 0x00000002 | Blk gap: 0x00000080 [ 140.017583] mmc2: sdhci: Wake-up: 0x00000008 | Clock: 0x0000000f [ 140.024039] mmc2: sdhci: Timeout: 0x0000008f | Int stat: 0x00000000 [ 140.030497] mmc2: sdhci: Int enab: 0x107f4000 | Sig enab: 0x107f4000 [ 140.036972] mmc2: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000502 [ 140.043426] mmc2: sdhci: Caps: 0x07eb0000 | Caps_1: 0x8000b407 [ 140.049867] mmc2: sdhci: Cmd: 0x00002c1a | Max curr: 0x00ffffff [ 140.056314] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0xffffffff [ 140.062755] mmc2: sdhci: Resp[2]: 0x328f5903 | Resp[3]: 0x00d00f00 [ 140.069195] mmc2: sdhci: Host ctl2: 0x00000008 [ 140.073640] mmc2: sdhci: ADMA Err: 0x00000007 | ADMA Ptr: 0x7809c108 [ 140.080079] mmc2: sdhci: ============================================ [ 140.086662] mmc2: running CQE recovery Fixes: 18094430d6b5 ("mmc: sdhci-esdhc-imx: add ADMA Length Mismatch errata fix") Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-28mmc: core: Add a debug print when the card may have been replacedhongjiefang3-2/+14
If the card was removed in suspended state and a new one was inserted, print a debug log when the check detects that it's not the old card. Signed-off-by: hongjiefang <hongjiefang@asrmicro.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-28Merge branch 'fixes' into nextUlf Hansson8-15/+39
2019-02-28mmc: core: Add sd discard timeoutAvri Altman1-0/+7
The busy timeout is 250msec per discard command. Signed-off-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-28mmc: core: Add discard support to sdAvri Altman2-5/+13
SD spec v5.1 adds discard support. The flows and commands are similar to mmc, so just set the discard arg in CMD38. A host which supports DISCARD shall check if the DISCARD_SUPPORT (b313) is set in the SD_STATUS register. If the card does not support discard, the host shall not issue DISCARD command, but ERASE command instead. Post the DISCARD operation, the card may de-allocate the discarded blocks partially or completely. So the host mustn't make any assumptions concerning the content of the discarded region. This is unlike ERASE command, in which the region is guaranteed to contain either '0's or '1's, depends on the content of DATA_STAT_AFTER_ERASE (b55) in the scr register. One more important difference compared to ERASE is the busy timeout which we will address on the next patch. Signed-off-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-28mmc: sdhci-esdhc-imx: clear the HALT bit when enable CQEBOUGH CHEN1-0/+13
After system suspend, CQE is in cqhci_off state, which set the HALT bit, make CQE in HALT state. If the SoC do not power down the USDHC module, then when system resume back, this bit keep the same, still set. Though there is a sdhci reset during sdhci_resume_host(), but this reset do not impact the CQE part, so need to clear this bit when enable CQE, otherwise CQE will stuck in the first CMDQ request after system resume back. Find this issue on NXP i.MX845s-mek board [ 105.919862] mmc2: cqhci: timeout for tag 6 [ 105.923965] mmc2: cqhci: ============ CQHCI REGISTER DUMP =========== [ 105.930407] mmc2: cqhci: Caps: 0x0000310a | Version: 0x00000510 [ 105.936847] mmc2: cqhci: Config: 0x00001001 | Control: 0x00000001 [ 105.943286] mmc2: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006 [ 105.949725] mmc2: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000 [ 105.956164] mmc2: cqhci: TDL base: 0x7809b000 | TDL up32: 0x00000000 [ 105.962604] mmc2: cqhci: Doorbell: 0x00000040 | TCN: 0x00000000 [ 105.969043] mmc2: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000 [ 105.975483] mmc2: cqhci: Task clr: 0x00000000 | SSC1: 0x00011000 [ 105.981922] mmc2: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000 [ 105.988362] mmc2: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000 [ 105.994801] mmc2: cqhci: Resp idx: 0x00000000 | Resp arg: 0x00000000 [ 106.001240] mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== [ 106.007680] mmc2: sdhci: Sys addr: 0xb2b37800 | Version: 0x00000002 [ 106.014120] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000001 [ 106.020560] mmc2: sdhci: Argument: 0x00010000 | Trn mode: 0x00000013 [ 106.026999] mmc2: sdhci: Present: 0x01f88008 | Host ctl: 0x00000030 [ 106.033439] mmc2: sdhci: Power: 0x00000002 | Blk gap: 0x00000080 [ 106.039878] mmc2: sdhci: Wake-up: 0x00000008 | Clock: 0x0000000f [ 106.046318] mmc2: sdhci: Timeout: 0x0000008f | Int stat: 0x00000000 [ 106.052757] mmc2: sdhci: Int enab: 0x107f4000 | Sig enab: 0x107f4000 [ 106.059196] mmc2: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000502 [ 106.065635] mmc2: sdhci: Caps: 0x07eb0000 | Caps_1: 0x8000b407 [ 106.072075] mmc2: sdhci: Cmd: 0x00000d1a | Max curr: 0x00ffffff [ 106.078514] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0x31360181 [ 106.084954] mmc2: sdhci: Resp[2]: 0x44473430 | Resp[3]: 0x00450100 [ 106.091392] mmc2: sdhci: Host ctl2: 0x00000008 [ 106.095836] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x7804b208 [ 106.102274] mmc2: sdhci: ============================================ [ 106.108785] mmc2: running CQE recovery Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-28mmc: core: do not retry CMD6 in __mmc_switch()Chaotian Jing1-1/+1
the response type of CMD6 is R1B, when the first CMD6 gets response CRC error, do retry may get timeout error due to card may still in busy state, which cause this retry make no sense. Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-27mmc: core: align max segment size with logical block sizeMing Lei2-7/+8
Logical block size is the lowest possible block size that the storage device can address. Max segment size is often related with controller's DMA capability. And it is reasonable to align max segment size with logical block size. SDHCI sets un-aligned max segment size, and causes ADMA error, so fix it by aligning max segment size with logical block size. Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: linux-block@vger.kernel.org Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-27mmc: cqhci: Fix a tiny potential memory leak on error conditionAlamy Liu1-1/+10
Free up the allocated memory in the case of error return The value of mmc_host->cqe_enabled stays 'false'. Thus, cqhci_disable (mmc_cqe_ops->cqe_disable) won't be called to free the memory. Also, cqhci_disable() seems to be designed to disable and free all resources, not suitable to handle this corner case. Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Alamy Liu <alamy.liu@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-27mmc: cqhci: fix space allocated for transfer descriptorAlamy Liu1-1/+1
There is not enough space being allocated when DCMD is disabled. CQE_DCMD is not necessary to be enabled when CQE is enabled. (Software could halt CQE to send command) In the case that CQE_DCMD is not enabled, it still needs to allocate space for data transfer. For instance: CQE_DCMD is enabled: 31 slots space (one slot used by DCMD) CQE_DCMD is disabled: 32 slots space Fixes: a4080225f51d ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Alamy Liu <alamy.liu@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-27mmc: core: Fix NULL ptr crash from mmc_should_fail_requestRitesh Harjani1-1/+1
In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD). In such case mmc_should_fail_request is directly dereferencing mrq->cmd while cmd is NULL. Fix this by checking for mrq->cmd pointer. Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests") Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-26mmc: tmio: fix access width of Block Count RegisterTakeshi Saito3-1/+11
In R-Car Gen2 or later, the maximum number of transfer blocks are changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register should use iowrite32(). If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this value will not be cleared. So, SD/MMC card initialization fails. So, check for the bigger register and use apropriate write. Also, mark the register as extended on Gen2. Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com> [wsa: use max_blk_count in if(), add Gen2, update commit message] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@kernel.org Reviewed-by: Simon Horman <horms+renesas@verge.net.au> [Ulf: Fixed build error] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: tmio_mmc_core: don't claim spurious interruptsSergei Shtylyov1-4/+7
I have encountered an interrupt storm during the eMMC chip probing (and the chip finally didn't get detected). It turned out that U-Boot left the DMAC interrupts enabled while the Linux driver didn't use those. The SDHI driver's interrupt handler somehow assumes that, even if an SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think that if none of the enabled interrupts happened and got handled, we should return IRQ_NONE -- that way the kernel IRQ code recoginizes a spurious interrupt and masks it off pretty quickly... Fixes: 7729c7a232a9 ("mmc: tmio: Provide separate interrupt handlers") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: core: Convert mmc_align_data_size() into an SDIO specific functionUlf Hansson3-36/+21
The only user of mmc_align_data_size() is sdio_align_size(), which is called from SDIO func drivers to let them distinguish, how to optimally allocate data buffers. Let's move mmc_align_data_size() close to the SDIO code as to make it static, rename it to _sdio_align_size() and simplify its definition, all with the purpose of clarifying that this is SDIO specific. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Avri Altman <avri.altman@wdc.com>
2019-02-25mmc: spi: Fix card detection during probeJonathan Neuschäfer1-0/+1
When using the mmc_spi driver with a card-detect pin, I noticed that the card was not detected immediately after probe, but only after it was unplugged and plugged back in (and the CD IRQ fired). The call tree looks something like this: mmc_spi_probe mmc_add_host mmc_start_host _mmc_detect_change mmc_schedule_delayed_work(&host->detect, 0) mmc_rescan host->bus_ops->detect(host) mmc_detect _mmc_detect_card_removed host->ops->get_cd(host) mmc_gpio_get_cd -> -ENOSYS (ctx->cd_gpio not set) mmc_gpiod_request_cd ctx->cd_gpio = desc To fix this issue, call mmc_detect_change after the card-detect GPIO/IRQ is registered. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: core: Move mmc_of_parse_voltage() to host.cUlf Hansson2-48/+44
MMC OF parsing functions, which parses various host DT properties, should stay close to each other. Therefore, let's move mmc_of_parse_voltage() close to mmc_of_parse() into host.c. Additionally, there is no reason to build the code only when CONFIG_OF is set, as there should be stub functions for the OF helpers that is being used, so let's drop this condition as well. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: core: Convert mmc_regulator_get_ocrmask() to staticUlf Hansson1-2/+1
The only left user of mmc_regulator_get_ocrmask() is the mmc core itself. Therefore, let's drop the export and turn it into static. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: core: Move regulator helpers to separate fileUlf Hansson4-243/+263
The mmc regulator helper functions, are placed in the extensive core.c file. In a step towards trying to create a better structure of files, avoiding too many lines of code per file, let's move these helpers to a new file, regulator.c. Moreover, this within this context it makes sense to also drop the export of mmc_vddrange_to_ocrmask(), but instead let's make it internal to the mmc core. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: of_mmc_spi: Convert to mmc_of_parse_voltage()Ulf Hansson1-21/+1
Let's drop the open-coding of the parsing of the "voltage-ranges" DT property and convert to use the common mmc_of_parse_voltage() API instead. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: core: Drop retries as in-parameter to mmc_wait_for_app_cmd()Ulf Hansson1-11/+5
All callers of mmc_wait_for_app_cmd() set the retries in-parameter to MMC_CMD_RETRIES. This is silly, so let's just drop the in-parameter altogether, as to simplify the code. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: core: Convert mmc_wait_for_app_cmd() to staticUlf Hansson2-19/+1
mmc_wait_for_app_cmd() is an internal function for sd_ops.c, thus let's drop the unnecessary export and turn it into static function. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: renesas_sdhi: Change HW adjustment register according to speed modeTakeshi Saito3-0/+11
SCC is used for SDR104/HS200/HS400. We need to change SCC_DT2FF according to the mode. If it is inappropriate, CRC error tends to occur. This adds variable "tap_hs400" for HS400 mode and configures SCC_DT2FF as needed. Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com> [wsa: rebased to upstream and updated commit message] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> Tested-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: mmci: Send a CMD12 to clear the DPSM at errorsUlf Hansson2-2/+24
The current approach with sending a CMD12 (STOP_TRANSMISSION) to complete a data transfer request, either because of using the open-ended transmission type or because of receiving an error during a pre-defined data transfer, isn't sufficient for the STM32 sdmmc variant. More precisely, this variant needs to clear the DPSM ("Data Path State Machine") by sending a CMD12, for all failing ADTC commands. Support this, by adding a struct mmc_command inside the struct mmci_host and initialize it to a CMD12 during ->probe(). Let's also add checks for the new conditions, to enable mmci_data_irq() and mmci_cmd_irq() to postpone the calls to mmci_request_end(), but instead send the CMD12. Cc: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Ludovic Barre <ludovic.barre@st.com>
2019-02-25mmc: sdhci-xenon: Fixup already marked switch fall-throughGustavo A. R. Silva1-1/+1
In preparation to enabling -Wimplicit-fallthrough, mark switch cases according to what the compiler looks for, where we are expecting to fall through. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-tegra: drop ->get_ro() implementationThomas Petazzoni1-9/+0
The SDHCI core is know properly checking for the state of a WP GPIO, so there is no longer any need for the sdhci-tegra code to implement ->get_ro() using mmc_gpio_get_ro(). Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Tested-by: Thierry Reding <treding@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-omap: drop ->get_ro() implementationThomas Petazzoni1-1/+0
The SDHCI core is now properly checking for the state of a WP GPIO, so there is no longer any need for the sdhci-omap code to implement ->get_ro() using mmc_gpio_get_ro(). Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci: use WP GPIO in sdhci_check_ro()Thomas Petazzoni1-0/+2
Even though SDHCI controllers may have a dedicated WP pin that can be queried using the SDHCI_PRESENT_STATE register, some platforms may chose to use a separate regular GPIO to route the WP signal. Such a GPIO is typically represented using the wp-gpios property in the Device Tree. Unfortunately, the current sdhci_check_ro() function does not make use of such GPIO when available: it either uses a host controller specific ->get_ro() operation, or uses the SDHCI_PRESENT_STATE. Several host controller specific ->get_ro() functions are implemented just to check a WP GPIO state. Instead of pushing this to more controller-specific implementations, let's handle this in the core SDHCI code, just like it is already done for the CD GPIO in sdhci_get_cd(). The below patch simply changes sdhci_check_ro() to use the value of the WP GPIO if available. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: wmt-sdmmc: Drop unused includeLinus Walleij1-1/+0
The WMT SDMMC driver uses slot GPIO helpers and does not make any use of <linux/gpio.h> so drop this surplus include. Cc: Tony Prisk <linux@prisktech.co.nz> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sunxi-mmc: Drop unused includesLinus Walleij1-2/+0
The Sunxi MMC driver uses slot GPIO helpers and does not make any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these surplus includes. Cc: Chen-Yu Tsai <wens@csie.org> Cc: Andre Przywara <andre.przywara@arm.com> Cc: cenowy Zheng <icenowy@aosc.io> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-pxav2: Drop unused includeLinus Walleij1-1/+0
The SDHCI PXAv2 driver uses slot GPIO helpers and does not make any use of <linux/gpio.h> so drop this surplus include. Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: sdhci-bcm-kona: Drop unused includesLinus Walleij1-2/+0
The SDHCI BCM Kona driver uses slot GPIO helpers and does not make any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these surplus includes. Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: mxs-mmc: Drop unused includesLinus Walleij1-2/+0
The MXS-MMC driver uses slot GPIO helpers and does not make any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these surplus includes. Cc: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: mxcmmc: Drop unused includesLinus Walleij1-2/+0
The MXCMMC driver uses slot GPIO helpers and does not make any use of <linux/gpio.h> or <linux/of_gpio.h> so drop these surplus includes. Cc: Jun Qian <hangdianqj@163.com> Cc: Matteo Facchinetti <matteo.facchinetti@sirius-es.it> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: cb710: fix indentation issue in if blockColin Ian King1-20/+22
There is an if block that is not indented, fix this. Also add a break statement on the default case to clean up a cppcheck warning. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: core: Indicate SD specs higher than 4.0Avri Altman1-0/+5
SD specs version 4.x and 5.x have a dedicated slices in the SCR register. Higher versions will rely on a combination of the existing fields. Signed-off-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: core: Calculate the discard arg only onceAvri Altman4-11/+15
In MMC, the discard arg is a read-only ext_csd parameter - set it once on card init. To be consistent, do that for SD as well even though its discard arg is always 0x0. Signed-off-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: slot-gpio: Remove override_active_level on WPLinus Walleij8-15/+8
The argument "override_active_level" made it possible to enforce a specific polarity on the write-protect GPIO line. All callers in the kernel pass "false" to this call after I have converted all drivers to use GPIO machine descriptors, so remove the argument and clean out this. This kind of polarity inversion should be handled by the GPIO descriptor inside the GPIO library if needed. This rids us of one instance of the kludgy calls into the gpiod_get_raw_value() API. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: bcm2835: Deduplicate reset of driver data on removeLukas Wunner1-1/+0
The BCM2835 MMC host driver sets the device's driver data pointer to NULL on ->remove() even though the driver core subsequently does the same in __device_release_driver(). Drop the duplicate assignment. Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-02-25mmc: bcm2835: Drop pointer to mmc_host from bcm2835_hostLukas Wunner1-10/+10
The BCM2835 MMC host driver uses a pointer to get from the private bcm2835_host structure to the generic mmc_host structure. However the latter is always immediately preceding the former in memory, so compute its address with a subtraction (which is cheaper than a dereference) and drop the superfluous pointer. No functional change intended. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Alexander Graf <agraf@suse.de> Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-26 09:55:01 +0000