From 470f22975448a65a1084a6f0721fa5df15323f02 Mon Sep 17 00:00:00 2001 From: Boojin Kim Date: Fri, 27 May 2011 19:04:03 -0700 Subject: ARM: SAMSUNG: serial: Fix on handling of one clock source for UART This patch fixes the way of comparison for handling of two or more clock sources for UART. For example, if just only one clock source is defined even though there are two clock sources for UART, the serial driver does not set proper clock up. Of course, it is problem. So this patch changes the condition of comparison to avoid useless setup clock and adds a flag 'NO_NEED_CHECK_CLKSRC' which means selection of source clock is not required. In addition, since the Exynos4210 has only one clock source for UART this patch adds the flag into its common_init_uarts(). Signed-off-by: Boojin Kim Signed-off-by: Kukjin Kim Cc: stable Signed-off-by: Greg Kroah-Hartman --- arch/arm/mach-exynos4/init.c | 1 + arch/arm/plat-samsung/include/plat/regs-serial.h | 2 ++ 2 files changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-exynos4/init.c b/arch/arm/mach-exynos4/init.c index cf91f50e43ab..a8a83e3881a4 100644 --- a/arch/arm/mach-exynos4/init.c +++ b/arch/arm/mach-exynos4/init.c @@ -35,6 +35,7 @@ void __init exynos4_common_init_uarts(struct s3c2410_uartcfg *cfg, int no) tcfg->clocks = exynos4_serial_clocks; tcfg->clocks_size = ARRAY_SIZE(exynos4_serial_clocks); } + tcfg->flags |= NO_NEED_CHECK_CLKSRC; } s3c24xx_init_uartdevs("s5pv210-uart", s5p_uart_resources, cfg, no); diff --git a/arch/arm/plat-samsung/include/plat/regs-serial.h b/arch/arm/plat-samsung/include/plat/regs-serial.h index c151c5f94a87..116edfe120b9 100644 --- a/arch/arm/plat-samsung/include/plat/regs-serial.h +++ b/arch/arm/plat-samsung/include/plat/regs-serial.h @@ -224,6 +224,8 @@ #define S5PV210_UFSTAT_RXMASK (255<<0) #define S5PV210_UFSTAT_RXSHIFT (0) +#define NO_NEED_CHECK_CLKSRC 1 + #ifndef __ASSEMBLY__ /* struct s3c24xx_uart_clksrc -- cgit v1.2.3 From 1a7d4369b3fe1f8e5efe7f11a1c482055693852f Mon Sep 17 00:00:00 2001 From: Shreshtha Kumar Sahu Date: Mon, 13 Jun 2011 10:11:44 +0200 Subject: amba pl011: platform data for reg lockup and glitch v2 This patch provides platform data for following - uart reset function to assist uart register lockup workaround - init/exit function to fix glitch in the tx pin in tty_open when tty port0 is opened a glitch is seen in the tx line of uart0. This happens in pl011_startup() when tx fifo interrupt is provoked into asserting. Now uart0 pins are enabled (alt function) only when init is complete and turned back to gpio when closed. Signed-off-by: Shreshtha Kumar Sahu Signed-off-by: Linus Walleij Signed-off-by: Greg Kroah-Hartman --- arch/arm/mach-ux500/board-mop500-pins.c | 16 +++++++--- arch/arm/mach-ux500/board-mop500.c | 54 +++++++++++++++++++++++++++++++++ 2 files changed, 66 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c index fd4cf1ca5efd..70cdbd60596a 100644 --- a/arch/arm/mach-ux500/board-mop500-pins.c +++ b/arch/arm/mach-ux500/board-mop500-pins.c @@ -110,10 +110,18 @@ static pin_cfg_t mop500_pins_common[] = { GPIO168_KP_O0, /* UART */ - GPIO0_U0_CTSn | PIN_INPUT_PULLUP, - GPIO1_U0_RTSn | PIN_OUTPUT_HIGH, - GPIO2_U0_RXD | PIN_INPUT_PULLUP, - GPIO3_U0_TXD | PIN_OUTPUT_HIGH, + /* uart-0 pins gpio configuration should be + * kept intact to prevent glitch in tx line + * when tty dev is opened. Later these pins + * are configured to uart mop500_pins_uart0 + * + * It will be replaced with uart configuration + * once the issue is solved. + */ + GPIO0_GPIO | PIN_INPUT_PULLUP, + GPIO1_GPIO | PIN_OUTPUT_HIGH, + GPIO2_GPIO | PIN_INPUT_PULLUP, + GPIO3_GPIO | PIN_OUTPUT_HIGH, GPIO29_U2_RXD | PIN_INPUT_PULLUP, GPIO30_U2_TXD | PIN_OUTPUT_HIGH, diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c index bb26f40493e6..2a08c07dec6d 100644 --- a/arch/arm/mach-ux500/board-mop500.c +++ b/arch/arm/mach-ux500/board-mop500.c @@ -27,18 +27,21 @@ #include #include #include +#include #include #include #include #include +#include #include #include #include #include +#include "pins-db8500.h" #include "ste-dma40-db8500.h" #include "devices-db8500.h" #include "board-mop500.h" @@ -393,12 +396,63 @@ static struct stedma40_chan_cfg uart2_dma_cfg_tx = { }; #endif + +static pin_cfg_t mop500_pins_uart0[] = { + GPIO0_U0_CTSn | PIN_INPUT_PULLUP, + GPIO1_U0_RTSn | PIN_OUTPUT_HIGH, + GPIO2_U0_RXD | PIN_INPUT_PULLUP, + GPIO3_U0_TXD | PIN_OUTPUT_HIGH, +}; + +#define PRCC_K_SOFTRST_SET 0x18 +#define PRCC_K_SOFTRST_CLEAR 0x1C +static void ux500_uart0_reset(void) +{ + void __iomem *prcc_rst_set, *prcc_rst_clr; + + prcc_rst_set = (void __iomem *)IO_ADDRESS(U8500_CLKRST1_BASE + + PRCC_K_SOFTRST_SET); + prcc_rst_clr = (void __iomem *)IO_ADDRESS(U8500_CLKRST1_BASE + + PRCC_K_SOFTRST_CLEAR); + + /* Activate soft reset PRCC_K_SOFTRST_CLEAR */ + writel((readl(prcc_rst_clr) | 0x1), prcc_rst_clr); + udelay(1); + + /* Release soft reset PRCC_K_SOFTRST_SET */ + writel((readl(prcc_rst_set) | 0x1), prcc_rst_set); + udelay(1); +} + +static void ux500_uart0_init(void) +{ + int ret; + + ret = nmk_config_pins(mop500_pins_uart0, + ARRAY_SIZE(mop500_pins_uart0)); + if (ret < 0) + pr_err("pl011: uart pins_enable failed\n"); +} + +static void ux500_uart0_exit(void) +{ + int ret; + + ret = nmk_config_pins_sleep(mop500_pins_uart0, + ARRAY_SIZE(mop500_pins_uart0)); + if (ret < 0) + pr_err("pl011: uart pins_disable failed\n"); +} + static struct amba_pl011_data uart0_plat = { #ifdef CONFIG_STE_DMA40 .dma_filter = stedma40_filter, .dma_rx_param = &uart0_dma_cfg_rx, .dma_tx_param = &uart0_dma_cfg_tx, #endif + .init = ux500_uart0_init, + .exit = ux500_uart0_exit, + .reset = ux500_uart0_reset, }; static struct amba_pl011_data uart1_plat = { -- cgit v1.2.3