summaryrefslogtreecommitdiff
path: root/drivers/tty/serial/xilinx_uartps.c
blob: f36bbba1ac8b9070cc7cefafb8a33265a7872253 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
/*
 * Xilinx PS UART driver
 *
 * 2011 (c) Xilinx Inc.
 *
 * This program is free software; you can redistribute it
 * and/or modify it under the terms of the GNU General Public
 * License as published by the Free Software Foundation;
 * either version 2 of the License, or (at your option) any
 * later version.
 *
 */

#include <linux/platform_device.h>
#include <linux/serial.h>
#include <linux/serial_core.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/console.h>
#include <linux/clk.h>
#include <linux/irq.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/module.h>

#define XUARTPS_TTY_NAME	"ttyPS"
#define XUARTPS_NAME		"xuartps"
#define XUARTPS_MAJOR		0	/* use dynamic node allocation */
#define XUARTPS_MINOR		0	/* works best with devtmpfs */
#define XUARTPS_NR_PORTS	2
#define XUARTPS_FIFO_SIZE	16	/* FIFO size */
#define XUARTPS_REGISTER_SPACE	0xFFF

#define xuartps_readl(offset)		ioread32(port->membase + offset)
#define xuartps_writel(val, offset)	iowrite32(val, port->membase + offset)

/********************************Register Map********************************/
/** UART
 *
 * Register offsets for the UART.
 *
 */
#define XUARTPS_CR_OFFSET	0x00  /* Control Register [8:0] */
#define XUARTPS_MR_OFFSET	0x04  /* Mode Register [10:0] */
#define XUARTPS_IER_OFFSET	0x08  /* Interrupt Enable [10:0] */
#define XUARTPS_IDR_OFFSET	0x0C  /* Interrupt Disable [10:0] */
#define XUARTPS_IMR_OFFSET	0x10  /* Interrupt Mask [10:0] */
#define XUARTPS_ISR_OFFSET	0x14  /* Interrupt Status [10:0]*/
#define XUARTPS_BAUDGEN_OFFSET	0x18  /* Baud Rate Generator [15:0] */
#define XUARTPS_RXTOUT_OFFSET	0x1C  /* RX Timeout [7:0] */
#define XUARTPS_RXWM_OFFSET	0x20  /* RX FIFO Trigger Level [5:0] */
#define XUARTPS_MODEMCR_OFFSET	0x24  /* Modem Control [5:0] */
#define XUARTPS_MODEMSR_OFFSET	0x28  /* Modem Status [8:0] */
#define XUARTPS_SR_OFFSET	0x2C  /* Channel Status [11:0] */
#define XUARTPS_FIFO_OFFSET	0x30  /* FIFO [15:0] or [7:0] */
#define XUARTPS_BAUDDIV_OFFSET	0x34  /* Baud Rate Divider [7:0] */
#define XUARTPS_FLOWDEL_OFFSET	0x38  /* Flow Delay [15:0] */
#define XUARTPS_IRRX_PWIDTH_OFFSET 0x3C /* IR Minimum Received Pulse
						Width [15:0] */
#define XUARTPS_IRTX_PWIDTH_OFFSET 0x40 /* IR Transmitted pulse
						Width [7:0] */
#define XUARTPS_TXWM_OFFSET	0x44  /* TX FIFO Trigger Level [5:0] */

/** Control Register
 *
 * The Control register (CR) controls the major functions of the device.
 *
 * Control Register Bit Definitions
 */
#define XUARTPS_CR_STOPBRK	0x00000100  /* Stop TX break */
#define XUARTPS_CR_STARTBRK	0x00000080  /* Set TX break */
#define XUARTPS_CR_TX_DIS	0x00000020  /* TX disabled. */
#define XUARTPS_CR_TX_EN	0x00000010  /* TX enabled */
#define XUARTPS_CR_RX_DIS	0x00000008  /* RX disabled. */
#define XUARTPS_CR_RX_EN	0x00000004  /* RX enabled */
#define XUARTPS_CR_TXRST	0x00000002  /* TX logic reset */
#define XUARTPS_CR_RXRST	0x00000001  /* RX logic reset */
#define XUARTPS_CR_RST_TO	0x00000040  /* Restart Timeout Counter */

/** Mode Register
 *
 * The mode register (MR) defines the mode of transfer as well as the data
 * format. If this register is modified during transmission or reception,
 * data validity cannot be guaranteed.
 *
 * Mode Register Bit Definitions
 *
 */
#define XUARTPS_MR_CLKSEL		0x00000001  /* Pre-scalar selection */
#define XUARTPS_MR_CHMODE_L_LOOP	0x00000200  /* Local loop back mode */
#define XUARTPS_MR_CHMODE_NORM		0x00000000  /* Normal mode */

#define XUARTPS_MR_STOPMODE_2_BIT	0x00000080  /* 2 stop bits */
#define XUARTPS_MR_STOPMODE_1_BIT	0x00000000  /* 1 stop bit */

#define XUARTPS_MR_PARITY_NONE		0x00000020  /* No parity mode */
#define XUARTPS_MR_PARITY_MARK		0x00000018  /* Mark parity mode */
#define XUARTPS_MR_PARITY_SPACE		0x00000010  /* Space parity mode */
#define XUARTPS_MR_PARITY_ODD		0x00000008  /* Odd parity mode */
#define XUARTPS_MR_PARITY_EVEN		0x00000000  /* Even parity mode */

#define XUARTPS_MR_CHARLEN_6_BIT	0x00000006  /* 6 bits data */
#define XUARTPS_MR_CHARLEN_7_BIT	0x00000004  /* 7 bits data */
#define XUARTPS_MR_CHARLEN_8_BIT	0x00000000  /* 8 bits data */

/** Interrupt Registers
 *
 * Interrupt control logic uses the interrupt enable register (IER) and the
 * interrupt disable register (IDR) to set the value of the bits in the
 * interrupt mask register (IMR). The IMR determines whether to pass an
 * interrupt to the interrupt status register (ISR).
 * Writing a 1 to IER Enables an interrupt, writing a 1 to IDR disables an
 * interrupt. IMR and ISR are read only, and IER and IDR are write only.
 * Reading either IER or IDR returns 0x00.
 *
 * All four registers have the same bit definitions.
 */
#define XUARTPS_IXR_TOUT	0x00000100 /* RX Timeout error interrupt */
#define XUARTPS_IXR_PARITY	0x00000080 /* Parity error interrupt */
#define XUARTPS_IXR_FRAMING	0x00000040 /* Framing error interrupt */
#define XUARTPS_IXR_OVERRUN	0x00000020 /* Overrun error interrupt */
#define XUARTPS_IXR_TXFULL	0x00000010 /* TX FIFO Full interrupt */
#define XUARTPS_IXR_TXEMPTY	0x00000008 /* TX FIFO empty interrupt */
#define XUARTPS_ISR_RXEMPTY	0x00000002 /* RX FIFO empty interrupt */
#define XUARTPS_IXR_RXTRIG	0x00000001 /* RX FIFO trigger interrupt */
#define XUARTPS_IXR_RXFULL	0x00000004 /* RX FIFO full interrupt. */
#define XUARTPS_IXR_RXEMPTY	0x00000002 /* RX FIFO empty interrupt. */
#define XUARTPS_IXR_MASK	0x00001FFF /* Valid bit mask */

/** Channel Status Register
 *
 * The channel status register (CSR) is provided to enable the control logic
 * to monitor the status of bits in the channel interrupt status register,
 * even if these are masked out by the interrupt mask register.
 */
#define XUARTPS_SR_RXEMPTY	0x00000002 /* RX FIFO empty */
#define XUARTPS_SR_TXEMPTY	0x00000008 /* TX FIFO empty */
#define XUARTPS_SR_TXFULL	0x00000010 /* TX FIFO full */
#define XUARTPS_SR_RXTRIG	0x00000001 /* Rx Trigger */

/**
 * xuartps_isr - Interrupt handler
 * @irq: Irq number
 * @dev_id: Id of the port
 *
 * Returns IRQHANDLED
 **/
static irqreturn_t xuartps_isr(int irq, void *dev_id)
{
	struct uart_port *port = (struct uart_port *)dev_id;
	unsigned long flags;
	unsigned int isrstatus, numbytes;
	unsigned int data;
	char status = TTY_NORMAL;

	spin_lock_irqsave(&port->lock, flags);

	/* Read the interrupt status register to determine which
	 * interrupt(s) is/are active.
	 */
	isrstatus = xuartps_readl(XUARTPS_ISR_OFFSET);

	/* drop byte with parity error if IGNPAR specified */
	if (isrstatus & port->ignore_status_mask & XUARTPS_IXR_PARITY)
		isrstatus &= ~(XUARTPS_IXR_RXTRIG | XUARTPS_IXR_TOUT);

	isrstatus &= port->read_status_mask;
	isrstatus &= ~port->ignore_status_mask;

	if ((isrstatus & XUARTPS_IXR_TOUT) ||
		(isrstatus & XUARTPS_IXR_RXTRIG)) {
		/* Receive Timeout Interrupt */
		while ((xuartps_readl(XUARTPS_SR_OFFSET) &
			XUARTPS_SR_RXEMPTY) != XUARTPS_SR_RXEMPTY) {
			data = xuartps_readl(XUARTPS_FIFO_OFFSET);
			port->icount.rx++;

			if (isrstatus & XUARTPS_IXR_PARITY) {
				port->icount.parity++;
				status = TTY_PARITY;
			} else if (isrstatus & XUARTPS_IXR_FRAMING) {
				port->icount.frame++;
				status = TTY_FRAME;
			} else if (isrstatus & XUARTPS_IXR_OVERRUN)
				port->icount.overrun++;

			uart_insert_char(port, isrstatus, XUARTPS_IXR_OVERRUN,
					data, status);
		}
		spin_unlock(&port->lock);
		tty_flip_buffer_push(&port->state->port);
		spin_lock(&port->lock);
	}

	/* Dispatch an appropriate handler */
	if ((isrstatus & XUARTPS_IXR_TXEMPTY) == XUARTPS_IXR_TXEMPTY) {
		if (uart_circ_empty(&port->state->xmit)) {
			xuartps_writel(XUARTPS_IXR_TXEMPTY,
						XUARTPS_IDR_OFFSET);
		} else {
			numbytes = port->fifosize;
			/* Break if no more data available in the UART buffer */
			while (numbytes--) {
				if (uart_circ_empty(&port->state->xmit))
					break;
				/* Get the data from the UART circular buffer
				 * and write it to the xuartps's TX_FIFO
				 * register.
				 */
				xuartps_writel(
					port->state->xmit.buf[port->state->xmit.
					tail], XUARTPS_FIFO_OFFSET);

				port->icount.tx++;

				/* Adjust the tail of the UART buffer and wrap
				 * the buffer if it reaches limit.
				 */
				port->state->xmit.tail =
					(port->state->xmit.tail + 1) & \
						(UART_XMIT_SIZE - 1);
			}

			if (uart_circ_chars_pending(
					&port->state->xmit) < WAKEUP_CHARS)
				uart_write_wakeup(port);
		}
	}

	xuartps_writel(isrstatus, XUARTPS_ISR_OFFSET);

	/* be sure to release the lock and tty before leaving */
	spin_unlock_irqrestore(&port->lock, flags);

	return IRQ_HANDLED;
}

/**
 * xuartps_set_baud_rate - Calculate and set the baud rate
 * @port: Handle to the uart port structure
 * @baud: Baud rate to set
 *
 * Returns baud rate, requested baud when possible, or actual baud when there
 *	was too much error
 **/
static unsigned int xuartps_set_baud_rate(struct uart_port *port,
						unsigned int baud)
{
	unsigned int sel_clk;
	unsigned int calc_baud = 0;
	unsigned int brgr_val, brdiv_val;
	unsigned int bauderror;

	/* Formula to obtain baud rate is
	 *	baud_tx/rx rate = sel_clk/CD * (BDIV + 1)
	 *	input_clk = (Uart User Defined Clock or Apb Clock)
	 *		depends on UCLKEN in MR Reg
	 *	sel_clk = input_clk or input_clk/8;
	 *		depends on CLKS in MR reg
	 *	CD and BDIV depends on values in
	 *			baud rate generate register
	 *			baud rate clock divisor register
	 */
	sel_clk = port->uartclk;
	if (xuartps_readl(XUARTPS_MR_OFFSET) & XUARTPS_MR_CLKSEL)
		sel_clk = sel_clk / 8;

	/* Find the best values for baud generation */
	for (brdiv_val = 4; brdiv_val < 255; brdiv_val++) {

		brgr_val = sel_clk / (baud * (brdiv_val + 1));
		if (brgr_val < 2 || brgr_val > 65535)
			continue;

		calc_baud = sel_clk / (brgr_val * (brdiv_val + 1));

		if (baud > calc_baud)
			bauderror = baud - calc_baud;
		else
			bauderror = calc_baud - baud;

		/* use the values when percent error is acceptable */
		if (((bauderror * 100) / baud) < 3) {
			calc_baud = baud;
			break;
		}
	}

	/* Set the values for the new baud rate */
	xuartps_writel(brgr_val, XUARTPS_BAUDGEN_OFFSET);
	xuartps_writel(brdiv_val, XUARTPS_BAUDDIV_OFFSET);

	return calc_baud;
}

/*----------------------Uart Operations---------------------------*/

/**
 * xuartps_start_tx -  Start transmitting bytes
 * @port: Handle to the uart port structure
 *
 **/
static void xuartps_start_tx(struct uart_port *port)
{
	unsigned int status, numbytes = port->fifosize;

	if (uart_circ_empty(&port->state->xmit) || uart_tx_stopped(port))
		return;

	status = xuartps_readl(XUARTPS_CR_OFFSET);
	/* Set the TX enable bit and clear the TX disable bit to enable the
	 * transmitter.
	 */
	xuartps_writel((status & ~XUARTPS_CR_TX_DIS) | XUARTPS_CR_TX_EN,
		XUARTPS_CR_OFFSET);

	while (numbytes-- && ((xuartps_readl(XUARTPS_SR_OFFSET)
		& XUARTPS_SR_TXFULL)) != XUARTPS_SR_TXFULL) {

		/* Break if no more data available in the UART buffer */
		if (uart_circ_empty(&port->state->xmit))
			break;

		/* Get the data from the UART circular buffer and
		 * write it to the xuartps's TX_FIFO register.
		 */
		xuartps_writel(
			port->state->xmit.buf[port->state->xmit.tail],
			XUARTPS_FIFO_OFFSET);
		port->icount.tx++;

		/* Adjust the tail of the UART buffer and wrap
		 * the buffer if it reaches limit.
		 */
		port->state->xmit.tail = (port->state->xmit.tail + 1) &
					(UART_XMIT_SIZE - 1);
	}

	/* Enable the TX Empty interrupt */
	xuartps_writel(XUARTPS_IXR_TXEMPTY, XUARTPS_IER_OFFSET);

	if (uart_circ_chars_pending(&port->state->xmit) < WAKEUP_CHARS)
		uart_write_wakeup(port);
}

/**
 * xuartps_stop_tx - Stop TX
 * @port: Handle to the uart port structure
 *
 **/
static void xuartps_stop_tx(struct uart_port *port)
{
	unsigned int regval;

	regval = xuartps_readl(XUARTPS_CR_OFFSET);
	regval |= XUARTPS_CR_TX_DIS;
	/* Disable the transmitter */
	xuartps_writel(regval, XUARTPS_CR_OFFSET);
}

/**
 * xuartps_stop_rx - Stop RX
 * @port: Handle to the uart port structure
 *
 **/
static void xuartps_stop_rx(struct uart_port *port)
{
	unsigned int regval;

	regval = xuartps_readl(XUARTPS_CR_OFFSET);
	regval |= XUARTPS_CR_RX_DIS;
	/* Disable the receiver */
	xuartps_writel(regval, XUARTPS_CR_OFFSET);
}

/**
 * xuartps_tx_empty -  Check whether TX is empty
 * @port: Handle to the uart port structure
 *
 * Returns TIOCSER_TEMT on success, 0 otherwise
 **/
static unsigned int xuartps_tx_empty(struct uart_port *port)
{
	unsigned int status;

	status = xuartps_readl(XUARTPS_ISR_OFFSET) & XUARTPS_IXR_TXEMPTY;
	return status ? TIOCSER_TEMT : 0;
}

/**
 * xuartps_break_ctl - Based on the input ctl we have to start or stop
 *			transmitting char breaks
 * @port: Handle to the uart port structure
 * @ctl: Value based on which start or stop decision is taken
 *
 **/
static void xuartps_break_ctl(struct uart_port *port, int ctl)
{
	unsigned int status;
	unsigned long flags;

	spin_lock_irqsave(&port->lock, flags);

	status = xuartps_readl(XUARTPS_CR_OFFSET);

	if (ctl == -1)
		xuartps_writel(XUARTPS_CR_STARTBRK | status,
					XUARTPS_CR_OFFSET);
	else {
		if ((status & XUARTPS_CR_STOPBRK) == 0)
			xuartps_writel(XUARTPS_CR_STOPBRK | status,
					 XUARTPS_CR_OFFSET);
	}
	spin_unlock_irqrestore(&port->lock, flags);
}

/**
 * xuartps_set_termios - termios operations, handling data length, parity,
 *				stop bits, flow control, baud rate
 * @port: Handle to the uart port structure
 * @termios: Handle to the input termios structure
 * @old: Values of the previously saved termios structure
 *
 **/
static void xuartps_set_termios(struct uart_port *port,
				struct ktermios *termios, struct ktermios *old)
{
	unsigned int cval = 0;
	unsigned int baud;
	unsigned long flags;
	unsigned int ctrl_reg, mode_reg;

	spin_lock_irqsave(&port->lock, flags);

	/* Empty the receive FIFO 1st before making changes */
	while ((xuartps_readl(XUARTPS_SR_OFFSET) &
		 XUARTPS_SR_RXEMPTY) != XUARTPS_SR_RXEMPTY) {
		xuartps_readl(XUARTPS_FIFO_OFFSET);
	}

	/* Disable the TX and RX to set baud rate */
	xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
			(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS),
			XUARTPS_CR_OFFSET);

	/* Min baud rate = 6bps and Max Baud Rate is 10Mbps for 100Mhz clk */
	baud = uart_get_baud_rate(port, termios, old, 0, 10000000);
	baud = xuartps_set_baud_rate(port, baud);
	if (tty_termios_baud_rate(termios))
		tty_termios_encode_baud_rate(termios, baud, baud);

	/*
	 * Update the per-port timeout.
	 */
	uart_update_timeout(port, termios->c_cflag, baud);

	/* Set TX/RX Reset */
	xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
			(XUARTPS_CR_TXRST | XUARTPS_CR_RXRST),
			XUARTPS_CR_OFFSET);

	ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);

	/* Clear the RX disable and TX disable bits and then set the TX enable
	 * bit and RX enable bit to enable the transmitter and receiver.
	 */
	xuartps_writel(
		(ctrl_reg & ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS))
			| (XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN),
			XUARTPS_CR_OFFSET);

	xuartps_writel(10, XUARTPS_RXTOUT_OFFSET);

	port->read_status_mask = XUARTPS_IXR_TXEMPTY | XUARTPS_IXR_RXTRIG |
			XUARTPS_IXR_OVERRUN | XUARTPS_IXR_TOUT;
	port->ignore_status_mask = 0;

	if (termios->c_iflag & INPCK)
		port->read_status_mask |= XUARTPS_IXR_PARITY |
		XUARTPS_IXR_FRAMING;

	if (termios->c_iflag & IGNPAR)
		port->ignore_status_mask |= XUARTPS_IXR_PARITY |
			XUARTPS_IXR_FRAMING | XUARTPS_IXR_OVERRUN;

	/* ignore all characters if CREAD is not set */
	if ((termios->c_cflag & CREAD) == 0)
		port->ignore_status_mask |= XUARTPS_IXR_RXTRIG |
			XUARTPS_IXR_TOUT | XUARTPS_IXR_PARITY |
			XUARTPS_IXR_FRAMING | XUARTPS_IXR_OVERRUN;

	mode_reg = xuartps_readl(XUARTPS_MR_OFFSET);

	/* Handling Data Size */
	switch (termios->c_cflag & CSIZE) {
	case CS6:
		cval |= XUARTPS_MR_CHARLEN_6_BIT;
		break;
	case CS7:
		cval |= XUARTPS_MR_CHARLEN_7_BIT;
		break;
	default:
	case CS8:
		cval |= XUARTPS_MR_CHARLEN_8_BIT;
		termios->c_cflag &= ~CSIZE;
		termios->c_cflag |= CS8;
		break;
	}

	/* Handling Parity and Stop Bits length */
	if (termios->c_cflag & CSTOPB)
		cval |= XUARTPS_MR_STOPMODE_2_BIT; /* 2 STOP bits */
	else
		cval |= XUARTPS_MR_STOPMODE_1_BIT; /* 1 STOP bit */

	if (termios->c_cflag & PARENB) {
		/* Mark or Space parity */
		if (termios->c_cflag & CMSPAR) {
			if (termios->c_cflag & PARODD)
				cval |= XUARTPS_MR_PARITY_MARK;
			else
				cval |= XUARTPS_MR_PARITY_SPACE;
		} else if (termios->c_cflag & PARODD)
				cval |= XUARTPS_MR_PARITY_ODD;
			else
				cval |= XUARTPS_MR_PARITY_EVEN;
	} else
		cval |= XUARTPS_MR_PARITY_NONE;
	xuartps_writel(cval , XUARTPS_MR_OFFSET);

	spin_unlock_irqrestore(&port->lock, flags);
}

/**
 * xuartps_startup - Called when an application opens a xuartps port
 * @port: Handle to the uart port structure
 *
 * Returns 0 on success, negative error otherwise
 **/
static int xuartps_startup(struct uart_port *port)
{
	unsigned int retval = 0, status = 0;

	retval = request_irq(port->irq, xuartps_isr, 0, XUARTPS_NAME,
								(void *)port);
	if (retval)
		return retval;

	/* Disable the TX and RX */
	xuartps_writel(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS,
						XUARTPS_CR_OFFSET);

	/* Set the Control Register with TX/RX Enable, TX/RX Reset,
	 * no break chars.
	 */
	xuartps_writel(XUARTPS_CR_TXRST | XUARTPS_CR_RXRST,
				XUARTPS_CR_OFFSET);

	status = xuartps_readl(XUARTPS_CR_OFFSET);

	/* Clear the RX disable and TX disable bits and then set the TX enable
	 * bit and RX enable bit to enable the transmitter and receiver.
	 */
	xuartps_writel((status & ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS))
			| (XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN |
			XUARTPS_CR_STOPBRK), XUARTPS_CR_OFFSET);

	/* Set the Mode Register with normal mode,8 data bits,1 stop bit,
	 * no parity.
	 */
	xuartps_writel(XUARTPS_MR_CHMODE_NORM | XUARTPS_MR_STOPMODE_1_BIT
		| XUARTPS_MR_PARITY_NONE | XUARTPS_MR_CHARLEN_8_BIT,
		 XUARTPS_MR_OFFSET);

	/* Set the RX FIFO Trigger level to 14 assuming FIFO size as 16 */
	xuartps_writel(14, XUARTPS_RXWM_OFFSET);

	/* Receive Timeout register is enabled with value of 10 */
	xuartps_writel(10, XUARTPS_RXTOUT_OFFSET);

	/* Clear out any pending interrupts before enabling them */
	xuartps_writel(xuartps_readl(XUARTPS_ISR_OFFSET), XUARTPS_ISR_OFFSET);

	/* Set the Interrupt Registers with desired interrupts */
	xuartps_writel(XUARTPS_IXR_TXEMPTY | XUARTPS_IXR_PARITY |
		XUARTPS_IXR_FRAMING | XUARTPS_IXR_OVERRUN |
		XUARTPS_IXR_RXTRIG | XUARTPS_IXR_TOUT, XUARTPS_IER_OFFSET);
	xuartps_writel(~(XUARTPS_IXR_TXEMPTY | XUARTPS_IXR_PARITY |
		XUARTPS_IXR_FRAMING | XUARTPS_IXR_OVERRUN |
		XUARTPS_IXR_RXTRIG | XUARTPS_IXR_TOUT), XUARTPS_IDR_OFFSET);

	return retval;
}

/**
 * xuartps_shutdown - Called when an application closes a xuartps port
 * @port: Handle to the uart port structure
 *
 **/
static void xuartps_shutdown(struct uart_port *port)
{
	int status;

	/* Disable interrupts */
	status = xuartps_readl(XUARTPS_IMR_OFFSET);
	xuartps_writel(status, XUARTPS_IDR_OFFSET);

	/* Disable the TX and RX */
	xuartps_writel(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS,
				 XUARTPS_CR_OFFSET);
	free_irq(port->irq, port);
}

/**
 * xuartps_type - Set UART type to xuartps port
 * @port: Handle to the uart port structure
 *
 * Returns string on success, NULL otherwise
 **/
static const char *xuartps_type(struct uart_port *port)
{
	return port->type == PORT_XUARTPS ? XUARTPS_NAME : NULL;
}

/**
 * xuartps_verify_port - Verify the port params
 * @port: Handle to the uart port structure
 * @ser: Handle to the structure whose members are compared
 *
 * Returns 0 if success otherwise -EINVAL
 **/
static int xuartps_verify_port(struct uart_port *port,
					struct serial_struct *ser)
{
	if (ser->type != PORT_UNKNOWN && ser->type != PORT_XUARTPS)
		return -EINVAL;
	if (port->irq != ser->irq)
		return -EINVAL;
	if (ser->io_type != UPIO_MEM)
		return -EINVAL;
	if (port->iobase != ser->port)
		return -EINVAL;
	if (ser->hub6 != 0)
		return -EINVAL;
	return 0;
}

/**
 * xuartps_request_port - Claim the memory region attached to xuartps port,
 *				called when the driver adds a xuartps port via
 *				uart_add_one_port()
 * @port: Handle to the uart port structure
 *
 * Returns 0, -ENOMEM if request fails
 **/
static int xuartps_request_port(struct uart_port *port)
{
	if (!request_mem_region(port->mapbase, XUARTPS_REGISTER_SPACE,
					 XUARTPS_NAME)) {
		return -ENOMEM;
	}

	port->membase = ioremap(port->mapbase, XUARTPS_REGISTER_SPACE);
	if (!port->membase) {
		dev_err(port->dev, "Unable to map registers\n");
		release_mem_region(port->mapbase, XUARTPS_REGISTER_SPACE);
		return -ENOMEM;
	}
	return 0;
}

/**
 * xuartps_release_port - Release the memory region attached to a xuartps
 *				port, called when the driver removes a xuartps
 *				port via uart_remove_one_port().
 * @port: Handle to the uart port structure
 *
 **/
static void xuartps_release_port(struct uart_port *port)
{
	release_mem_region(port->mapbase, XUARTPS_REGISTER_SPACE);
	iounmap(port->membase);
	port->membase = NULL;
}

/**
 * xuartps_config_port - Configure xuartps, called when the driver adds a
 *				xuartps port
 * @port: Handle to the uart port structure
 * @flags: If any
 *
 **/
static void xuartps_config_port(struct uart_port *port, int flags)
{
	if (flags & UART_CONFIG_TYPE && xuartps_request_port(port) == 0)
		port->type = PORT_XUARTPS;
}

/**
 * xuartps_get_mctrl - Get the modem control state
 *
 * @port: Handle to the uart port structure
 *
 * Returns the modem control state
 *
 **/
static unsigned int xuartps_get_mctrl(struct uart_port *port)
{
	return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
}

static void xuartps_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
	/* N/A */
}

static void xuartps_enable_ms(struct uart_port *port)
{
	/* N/A */
}

/** The UART operations structure
 */
static struct uart_ops xuartps_ops = {
	.set_mctrl	= xuartps_set_mctrl,
	.get_mctrl	= xuartps_get_mctrl,
	.enable_ms	= xuartps_enable_ms,

	.start_tx	= xuartps_start_tx,	/* Start transmitting */
	.stop_tx	= xuartps_stop_tx,	/* Stop transmission */
	.stop_rx	= xuartps_stop_rx,	/* Stop reception */
	.tx_empty	= xuartps_tx_empty,	/* Transmitter busy? */
	.break_ctl	= xuartps_break_ctl,	/* Start/stop
						 * transmitting break
						 */
	.set_termios	= xuartps_set_termios,	/* Set termios */
	.startup	= xuartps_startup,	/* App opens xuartps */
	.shutdown	= xuartps_shutdown,	/* App closes xuartps */
	.type		= xuartps_type,		/* Set UART type */
	.verify_port	= xuartps_verify_port,	/* Verification of port
						 * params
						 */
	.request_port	= xuartps_request_port,	/* Claim resources
						 * associated with a
						 * xuartps port
						 */
	.release_port	= xuartps_release_port,	/* Release resources
						 * associated with a
						 * xuartps port
						 */
	.config_port	= xuartps_config_port,	/* Configure when driver
						 * adds a xuartps port
						 */
};

static struct uart_port xuartps_port[2];

/**
 * xuartps_get_port - Configure the port from the platform device resource
 *			info
 *
 * Returns a pointer to a uart_port or NULL for failure
 **/
static struct uart_port *xuartps_get_port(void)
{
	struct uart_port *port;
	int id;

	/* Find the next unused port */
	for (id = 0; id < XUARTPS_NR_PORTS; id++)
		if (xuartps_port[id].mapbase == 0)
			break;

	if (id >= XUARTPS_NR_PORTS)
		return NULL;

	port = &xuartps_port[id];

	/* At this point, we've got an empty uart_port struct, initialize it */
	spin_lock_init(&port->lock);
	port->membase	= NULL;
	port->iobase	= 1; /* mark port in use */
	port->irq	= 0;
	port->type	= PORT_UNKNOWN;
	port->iotype	= UPIO_MEM32;
	port->flags	= UPF_BOOT_AUTOCONF;
	port->ops	= &xuartps_ops;
	port->fifosize	= XUARTPS_FIFO_SIZE;
	port->line	= id;
	port->dev	= NULL;
	return port;
}

/*-----------------------Console driver operations--------------------------*/

#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
/**
 * xuartps_console_wait_tx - Wait for the TX to be full
 * @port: Handle to the uart port structure
 *
 **/
static void xuartps_console_wait_tx(struct uart_port *port)
{
	while ((xuartps_readl(XUARTPS_SR_OFFSET) & XUARTPS_SR_TXEMPTY)
				!= XUARTPS_SR_TXEMPTY)
		barrier();
}

/**
 * xuartps_console_putchar - write the character to the FIFO buffer
 * @port: Handle to the uart port structure
 * @ch: Character to be written
 *
 **/
static void xuartps_console_putchar(struct uart_port *port, int ch)
{
	xuartps_console_wait_tx(port);
	xuartps_writel(ch, XUARTPS_FIFO_OFFSET);
}

/**
 * xuartps_console_write - perform write operation
 * @port: Handle to the uart port structure
 * @s: Pointer to character array
 * @count: No of characters
 **/
static void xuartps_console_write(struct console *co, const char *s,
				unsigned int count)
{
	struct uart_port *port = &xuartps_port[co->index];
	unsigned long flags;
	unsigned int imr;
	int locked = 1;

	if (oops_in_progress)
		locked = spin_trylock_irqsave(&port->lock, flags);
	else
		spin_lock_irqsave(&port->lock, flags);

	/* save and disable interrupt */
	imr = xuartps_readl(XUARTPS_IMR_OFFSET);
	xuartps_writel(imr, XUARTPS_IDR_OFFSET);

	uart_console_write(port, s, count, xuartps_console_putchar);
	xuartps_console_wait_tx(port);

	/* restore interrupt state, it seems like there may be a h/w bug
	 * in that the interrupt enable register should not need to be
	 * written based on the data sheet
	 */
	xuartps_writel(~imr, XUARTPS_IDR_OFFSET);
	xuartps_writel(imr, XUARTPS_IER_OFFSET);

	if (locked)
		spin_unlock_irqrestore(&port->lock, flags);
}

/**
 * xuartps_console_setup - Initialize the uart to default config
 * @co: Console handle
 * @options: Initial settings of uart
 *
 * Returns 0, -ENODEV if no device
 **/
static int __init xuartps_console_setup(struct console *co, char *options)
{
	struct uart_port *port = &xuartps_port[co->index];
	int baud = 9600;
	int bits = 8;
	int parity = 'n';
	int flow = 'n';

	if (co->index < 0 || co->index >= XUARTPS_NR_PORTS)
		return -EINVAL;

	if (!port->mapbase) {
		pr_debug("console on ttyPS%i not present\n", co->index);
		return -ENODEV;
	}

	if (options)
		uart_parse_options(options, &baud, &parity, &bits, &flow);

	return uart_set_options(port, co, baud, parity, bits, flow);
}

static struct uart_driver xuartps_uart_driver;

static struct console xuartps_console = {
	.name	= XUARTPS_TTY_NAME,
	.write	= xuartps_console_write,
	.device	= uart_console_device,
	.setup	= xuartps_console_setup,
	.flags	= CON_PRINTBUFFER,
	.index	= -1, /* Specified on the cmdline (e.g. console=ttyPS ) */
	.data	= &xuartps_uart_driver,
};

/**
 * xuartps_console_init - Initialization call
 *
 * Returns 0 on success, negative error otherwise
 **/
static int __init xuartps_console_init(void)
{
	register_console(&xuartps_console);
	return 0;
}

console_initcall(xuartps_console_init);

#endif /* CONFIG_SERIAL_XILINX_PS_UART_CONSOLE */

/** Structure Definitions
 */
static struct uart_driver xuartps_uart_driver = {
	.owner		= THIS_MODULE,		/* Owner */
	.driver_name	= XUARTPS_NAME,		/* Driver name */
	.dev_name	= XUARTPS_TTY_NAME,	/* Node name */
	.major		= XUARTPS_MAJOR,	/* Major number */
	.minor		= XUARTPS_MINOR,	/* Minor number */
	.nr		= XUARTPS_NR_PORTS,	/* Number of UART ports */
#ifdef CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
	.cons		= &xuartps_console,	/* Console */
#endif
};

/* ---------------------------------------------------------------------
 * Platform bus binding
 */
/**
 * xuartps_probe - Platform driver probe
 * @pdev: Pointer to the platform device structure
 *
 * Returns 0 on success, negative error otherwise
 **/
static int xuartps_probe(struct platform_device *pdev)
{
	int rc;
	struct uart_port *port;
	struct resource *res, *res2;
	struct clk *clk;

	clk = of_clk_get(pdev->dev.of_node, 0);
	if (IS_ERR(clk)) {
		dev_err(&pdev->dev, "no clock specified\n");
		return PTR_ERR(clk);
	}

	rc = clk_prepare_enable(clk);
	if (rc) {
		dev_err(&pdev->dev, "could not enable clock\n");
		return -EBUSY;
	}

	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	if (!res)
		return -ENODEV;

	res2 = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
	if (!res2)
		return -ENODEV;

	/* Initialize the port structure */
	port = xuartps_get_port();

	if (!port) {
		dev_err(&pdev->dev, "Cannot get uart_port structure\n");
		return -ENODEV;
	} else {
		/* Register the port.
		 * This function also registers this device with the tty layer
		 * and triggers invocation of the config_port() entry point.
		 */
		port->mapbase = res->start;
		port->irq = res2->start;
		port->dev = &pdev->dev;
		port->uartclk = clk_get_rate(clk);
		port->private_data = clk;
		dev_set_drvdata(&pdev->dev, port);
		rc = uart_add_one_port(&xuartps_uart_driver, port);
		if (rc) {
			dev_err(&pdev->dev,
				"uart_add_one_port() failed; err=%i\n", rc);
			dev_set_drvdata(&pdev->dev, NULL);
			return rc;
		}
		return 0;
	}
}

/**
 * xuartps_remove - called when the platform driver is unregistered
 * @pdev: Pointer to the platform device structure
 *
 * Returns 0 on success, negative error otherwise
 **/
static int xuartps_remove(struct platform_device *pdev)
{
	struct uart_port *port = dev_get_drvdata(&pdev->dev);
	struct clk *clk = port->private_data;
	int rc;

	/* Remove the xuartps port from the serial core */
	rc = uart_remove_one_port(&xuartps_uart_driver, port);
	dev_set_drvdata(&pdev->dev, NULL);
	port->mapbase = 0;
	clk_disable_unprepare(clk);
	return rc;
}

/**
 * xuartps_suspend - suspend event
 * @pdev: Pointer to the platform device structure
 * @state: State of the device
 *
 * Returns 0
 **/
static int xuartps_suspend(struct platform_device *pdev, pm_message_t state)
{
	/* Call the API provided in serial_core.c file which handles
	 * the suspend.
	 */
	uart_suspend_port(&xuartps_uart_driver, &xuartps_port[pdev->id]);
	return 0;
}

/**
 * xuartps_resume - Resume after a previous suspend
 * @pdev: Pointer to the platform device structure
 *
 * Returns 0
 **/
static int xuartps_resume(struct platform_device *pdev)
{
	uart_resume_port(&xuartps_uart_driver, &xuartps_port[pdev->id]);
	return 0;
}

/* Match table for of_platform binding */
static struct of_device_id xuartps_of_match[] = {
	{ .compatible = "xlnx,xuartps", },
	{}
};
MODULE_DEVICE_TABLE(of, xuartps_of_match);

static struct platform_driver xuartps_platform_driver = {
	.probe   = xuartps_probe,		/* Probe method */
	.remove  = xuartps_remove,		/* Detach method */
	.suspend = xuartps_suspend,		/* Suspend */
	.resume  = xuartps_resume,		/* Resume after a suspend */
	.driver  = {
		.owner = THIS_MODULE,
		.name = XUARTPS_NAME,		/* Driver name */
		.of_match_table = xuartps_of_match,
		},
};

/* ---------------------------------------------------------------------
 * Module Init and Exit
 */
/**
 * xuartps_init - Initial driver registration call
 *
 * Returns whether the registration was successful or not
 **/
static int __init xuartps_init(void)
{
	int retval = 0;

	/* Register the xuartps driver with the serial core */
	retval = uart_register_driver(&xuartps_uart_driver);
	if (retval)
		return retval;

	/* Register the platform driver */
	retval = platform_driver_register(&xuartps_platform_driver);
	if (retval)
		uart_unregister_driver(&xuartps_uart_driver);

	return retval;
}

/**
 * xuartps_exit - Driver unregistration call
 **/
static void __exit xuartps_exit(void)
{
	/* The order of unregistration is important. Unregister the
	 * UART driver before the platform driver crashes the system.
	 */

	/* Unregister the platform driver */
	platform_driver_unregister(&xuartps_platform_driver);

	/* Unregister the xuartps driver */
	uart_unregister_driver(&xuartps_uart_driver);
}

module_init(xuartps_init);
module_exit(xuartps_exit);

MODULE_DESCRIPTION("Driver for PS UART");
MODULE_AUTHOR("Xilinx Inc.");
MODULE_LICENSE("GPL");