AMD64 specific boot options There are many others (usually documented in driver documentation), but only the AMD64 specific ones are listed here. Machine check mce=off disable machine check mce=bootlog Enable logging of machine checks left over from booting. Disabled by default because some BIOS leave bogus ones. If your BIOS doesn't do that it's a good idea to enable though to make sure you log even machine check events that result in a reboot. nomce (for compatibility with i386): same as mce=off Everything else is in sysfs now. APICs apic Use IO-APIC. Default noapic Don't use the IO-APIC. disableapic Don't use the local APIC nolapic Don't use the local APIC (alias for i386 compatibility) pirq=... See Documentation/i386/IO-APIC.txt noapictimer Don't set up the APIC timer no_timer_check Don't check the IO-APIC timer. This can work around problems with incorrect timer initialization on some boards. Early Console syntax: earlyprintk=vga earlyprintk=serial[,ttySn[,baudrate]] The early console is useful when the kernel crashes before the normal console is initialized. It is not enabled by default because it has some cosmetic problems. Append ,keep to not disable it when the real console takes over. Only vga or serial at a time, not both. Currently only ttyS0 and ttyS1 are supported. Interaction with the standard serial driver is not very good. The VGA output is eventually overwritten by the real console. Timing notsc Don't use the CPU time stamp counter to read the wall time. This can be used to work around timing problems on multiprocessor systems with not properly synchronized CPUs. report_lost_ticks Report when timer interrupts are lost because some code turned off interrupts for too long. nmi_watchdog=NUMBER[,panic] NUMBER can be: 0 don't use an NMI watchdog 1 use the IO-APIC timer for the NMI watchdog 2 use the local APIC for the NMI watchdog using a performance counter. Note This will use one performance counter and the local APIC's performance vector. When panic is specified panic when an NMI watchdog timeout occurs. This is useful when you use a panic=... timeout and need the box quickly up again. nohpet Don't use the HPET timer. Idle loop idle=poll Don't do power saving in the idle loop using HLT, but poll for rescheduling event. This will make the CPUs eat a lot more power, but may be useful to get slightly better performance in multiprocessor benchmarks. It also makes some profiling using performance counters more accurate. Please note that on systems with MONITOR/MWAIT support (like Intel EM64T CPUs) this option has no performance advantage over the normal idle loop. It may also interact badly with hyperthreading. Rebooting reboot=b[ios] | t[riple] | k[bd] [, [w]arm | [c]old] bios Use the CPU reboto vector for warm reset warm Don't set the cold reboot flag cold Set the cold reboot flag triple Force a triple fault (init) kbd Use the keyboard controller. cold reset (default) Using warm reset will be much faster especially on big memory systems because the BIOS will not go through the memory check. Disadvantage is that not all hardware will be completely reinitialized on reboot so there may be boot problems on some systems. reboot=force Don't stop other CPUs on reboot. This can make reboot more reliable in some cases. Non Executable Mappings noexec=on|off on Enable(default) off Disable SMP nosmp Only use a single CPU maxcpus=NUMBER only use upto NUMBER CPUs cpumask=MASK only use cpus with bits set in mask NUMA numa=off Only set up a single NUMA node spanning all memory. numa=noacpi Don't parse the SRAT table for NUMA setup numa=fake=X Fake X nodes and ignore NUMA setup of the actual machine. ACPI acpi=off Don't enable ACPI acpi=ht Use ACPI boot table parsing, but don't enable ACPI interpreter acpi=force Force ACPI on (currently not needed) acpi=strict Disable out of spec ACPI workarounds. acpi_sci={edge,level,high,low} Set up ACPI SCI interrupt. acpi=noirq Don't route interrupts PCI pci=off Don't use PCI pci=conf1 Use conf1 access. pci=conf2 Use conf2 access. pci=rom Assign ROMs. pci=assign-busses Assign busses pci=irqmask=MASK Set PCI interrupt mask to MASK pci=lastbus=NUMBER Scan upto NUMBER busses, no matter what the mptable says. pci=noacpi Don't use ACPI to set up PCI interrupt routing. IOMMU iommu=[size][,noagp][,off][,force][,noforce][,leak][,memaper[=order]][,merge] [,forcesac][,fullflush][,nomerge][,noaperture] size set size of iommu (in bytes) noagp don't initialize the AGP driver and use full aperture. off don't use the IOMMU leak turn on simple iommu leak tracing (only when CONFIG_IOMMU_LEAK is on) memaper[=order] allocate an own aperture over RAM with size 32MB^order. noforce don't force IOMMU usage. Default. force Force IOMMU. merge Do SG merging. Implies force (experimental) nomerge Don't do SG merging. forcesac For SAC mode for masks <40bits (experimental) fullflush Flush IOMMU on each allocation (default) nofullflush Don't use IOMMU fullflush allowed overwrite iommu off workarounds for specific chipsets. soft Use software bounce buffering (default for Intel machines) noaperture Don't touch the aperture for AGP. swiotlb=pages[,force] pages Prereserve that many 128K pages for the software IO bounce buffering. force Force all IO through the software TLB. Debugging oops=panic Always panic on oopses. Default is to just kill the process, but there is a small probability of deadlocking the machine. This will also cause panics on machine check exceptions. Useful together with panic=30 to trigger a reboot. kstack=N Print that many words from the kernel stack in oops dumps. Misc noreplacement Don't replace instructions with more appropiate ones for the CPU. This may be useful on asymmetric MP systems where some CPU have less capabilities than the others.