From 284d115ec9b70d7c38752d10ad393a198db07a4b Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 20 Apr 2008 17:32:16 +0100 Subject: [ARM] pxa: separate PXA25x and PXA27x UDC register definitions The PXA25x and PXA27x USB device controller register definitions are different. Currently, they live side by side in pxa-regs.h, but only one set is available depending on the setting of PXA25x or PXA27x. This means that if we build to support both PXA25x and PXA27x, the PXA27x definitions are unavailable, even to PXA27x specific code. Remove these definitions from pxa-regs.h, and place them in separate files. Include these files where appropriate. Note: according to the dependencies in drivers/usb/gadget/Kconfig, we do not support the UDC on PXA27x nor PXA3xx CPUs, so remove the platform devices from pxa27x.c and pxa3xx.c. Signed-off-by: Russell King --- drivers/usb/gadget/pxa2xx_udc.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'drivers/usb/gadget') diff --git a/drivers/usb/gadget/pxa2xx_udc.c b/drivers/usb/gadget/pxa2xx_udc.c index 08f699b1fc5..63db96adc0b 100644 --- a/drivers/usb/gadget/pxa2xx_udc.c +++ b/drivers/usb/gadget/pxa2xx_udc.c @@ -46,19 +46,25 @@ #include #include #include +#include #include #include #include -#include #include #include #include -#include #include #include +/* + * This driver is PXA25x only. Grab the right register definitions. + */ +#ifdef CONFIG_ARCH_PXA +#include +#endif + #include -- cgit v1.2.3 From ba45ca435060614e595a107ac323a36b52619d7d Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Tue, 8 Apr 2008 13:59:18 +0100 Subject: [ARM] 4940/1: AT91: UDPHS driver: SAM9RL board and cpu integration. Adds support for the USB High Speed Device Port on the AT91SAM9RL system on chip. The AT91SAM9RL uses the same UDPHS IP as the AVR32 and the AT91CAP9 (atmel_usba_udc driver). Signed-off-by: Nicolas Ferre Acked-by: Andrew Victor Signed-off-by: Russell King --- drivers/usb/gadget/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/usb/gadget') diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig index 6e784d2db42..3565d435282 100644 --- a/drivers/usb/gadget/Kconfig +++ b/drivers/usb/gadget/Kconfig @@ -118,10 +118,10 @@ config USB_AMD5536UDC config USB_GADGET_ATMEL_USBA boolean "Atmel USBA" select USB_GADGET_DUALSPEED - depends on AVR32 || ARCH_AT91CAP9 + depends on AVR32 || ARCH_AT91CAP9 || ARCH_AT91SAM9RL help USBA is the integrated high-speed USB Device controller on - the AT32AP700x and AT91CAP9 processors from Atmel. + the AT32AP700x, some AT91SAM9 and AT91CAP9 processors from Atmel. config USB_ATMEL_USBA tristate -- cgit v1.2.3 From d438ae5796085379327bdba76114929eedf94a89 Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Fri, 6 Jun 2008 18:40:47 +0100 Subject: [ARM] 5080/1: touch PSSR_OTGPH only on pxa27x in ohci-pxa27x and pxa27x_udc and include pxa2xx-regs.h as build fix since PSSR definitions moved from pxa-regs.h into pxa2xx-regs.h. Note: This change is temporary as pxa27x processor specific code will be finally moved elsewhere (both drivers should support pxa3xx, too). Signed-off-by: Philipp Zabel Acked-by: Eric Miao Signed-off-by: Russell King --- drivers/usb/gadget/pxa27x_udc.c | 5 +++-- drivers/usb/gadget/pxa27x_udc.h | 8 -------- 2 files changed, 3 insertions(+), 10 deletions(-) (limited to 'drivers/usb/gadget') diff --git a/drivers/usb/gadget/pxa27x_udc.c b/drivers/usb/gadget/pxa27x_udc.c index 499b7a23f35..40d6b580f15 100644 --- a/drivers/usb/gadget/pxa27x_udc.c +++ b/drivers/usb/gadget/pxa27x_udc.c @@ -38,7 +38,7 @@ #include #include #include - +#include /* FIXME: for PSSR */ #include #include "pxa27x_udc.h" @@ -2359,7 +2359,8 @@ static int pxa_udc_resume(struct platform_device *_dev) * Software must configure the USB OTG pad, UDC, and UHC * to the state they were in before entering sleep mode. */ - PSSR |= PSSR_OTGPH; + if (cpu_is_pxa27x()) + PSSR |= PSSR_OTGPH; return 0; } diff --git a/drivers/usb/gadget/pxa27x_udc.h b/drivers/usb/gadget/pxa27x_udc.h index 97453db924f..1d1b7936ee1 100644 --- a/drivers/usb/gadget/pxa27x_udc.h +++ b/drivers/usb/gadget/pxa27x_udc.h @@ -484,12 +484,4 @@ static inline struct pxa_udc *to_gadget_udc(struct usb_gadget *gadget) #define ep_warn(ep, fmt, arg...) \ dev_warn(ep->dev->dev, "%s:%s:" fmt, EPNAME(ep), __func__, ## arg) -/* - * Cannot include pxa-regs.h, as register names are similar. - * So PSSR is redefined here. This should be removed once UDC registers will - * be gone from pxa-regs.h. - */ -#define PSSR __REG(0x40F00004) /* Power Manager Sleep Status */ -#define PSSR_OTGPH (1 << 6) /* OTG Peripheral Hold */ - #endif /* __LINUX_USB_GADGET_PXA27X_H */ -- cgit v1.2.3 From b2f2ba01b2a4356e92231669f7e3dcee37ac2fca Mon Sep 17 00:00:00 2001 From: Jonathan Corbet Date: Fri, 16 May 2008 14:21:30 -0600 Subject: printer gadget: BKL pushdown Add explicit lock_kernel() calls to printer_open() Signed-off-by: Jonathan Corbet --- drivers/usb/gadget/printer.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/usb/gadget') diff --git a/drivers/usb/gadget/printer.c b/drivers/usb/gadget/printer.c index 76be75e3ab8..ec8f2eb041c 100644 --- a/drivers/usb/gadget/printer.c +++ b/drivers/usb/gadget/printer.c @@ -462,6 +462,7 @@ printer_open(struct inode *inode, struct file *fd) unsigned long flags; int ret = -EBUSY; + lock_kernel(); dev = container_of(inode->i_cdev, struct printer_dev, printer_cdev); spin_lock_irqsave(&dev->lock, flags); @@ -477,7 +478,7 @@ printer_open(struct inode *inode, struct file *fd) spin_unlock_irqrestore(&dev->lock, flags); DBG(dev, "printer_open returned %x\n", ret); - + unlock_kernel(); return ret; } -- cgit v1.2.3 From 0499bdeb1dec30325aa282a83f9374fa849aa01c Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:36 +0300 Subject: ARM: OMAP: DMA: Remove __REG access Remove __REG access in DMA code, use dma_read/write instead: - dynamically set the omap_dma_base based on the omap type - omap_read/write becomes dma_read/write - dma channel registers are read with dma_ch_read/write Cc: David Brownell Cc: linux-usb@vger.kernel.org Signed-off-by: Tony Lindgren --- drivers/usb/gadget/omap_udc.c | 42 ++++++------------------------------------ 1 file changed, 6 insertions(+), 36 deletions(-) (limited to 'drivers/usb/gadget') diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c index 881d74c3d96..86c029a8d99 100644 --- a/drivers/usb/gadget/omap_udc.c +++ b/drivers/usb/gadget/omap_udc.c @@ -491,32 +491,6 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req) /*-------------------------------------------------------------------------*/ -static inline dma_addr_t dma_csac(unsigned lch) -{ - dma_addr_t csac; - - /* omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is - * read before the DMA controller finished disabling the channel. - */ - csac = OMAP_DMA_CSAC_REG(lch); - if (csac == 0) - csac = OMAP_DMA_CSAC_REG(lch); - return csac; -} - -static inline dma_addr_t dma_cdac(unsigned lch) -{ - dma_addr_t cdac; - - /* omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is - * read before the DMA controller finished disabling the channel. - */ - cdac = OMAP_DMA_CDAC_REG(lch); - if (cdac == 0) - cdac = OMAP_DMA_CDAC_REG(lch); - return cdac; -} - static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) { dma_addr_t end; @@ -527,7 +501,7 @@ static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) if (cpu_is_omap15xx()) return 0; - end = dma_csac(ep->lch); + end = omap_get_dma_src_pos(ep->lch); if (end == ep->dma_counter) return 0; @@ -537,15 +511,11 @@ static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) return end - start; } -#define DMA_DEST_LAST(x) (cpu_is_omap15xx() \ - ? OMAP_DMA_CSAC_REG(x) /* really: CPC */ \ - : dma_cdac(x)) - static u16 dma_dest_len(struct omap_ep *ep, dma_addr_t start) { dma_addr_t end; - end = DMA_DEST_LAST(ep->lch); + end = omap_get_dma_dst_pos(ep->lch); if (end == ep->dma_counter) return 0; @@ -596,7 +566,7 @@ static void next_in_dma(struct omap_ep *ep, struct omap_req *req) 0, 0); omap_start_dma(ep->lch); - ep->dma_counter = dma_csac(ep->lch); + ep->dma_counter = omap_get_dma_src_pos(ep->lch); UDC_DMA_IRQ_EN_REG |= UDC_TX_DONE_IE(ep->dma_channel); UDC_TXDMA_REG(ep->dma_channel) = UDC_TXN_START | txdma_ctrl; req->dma_bytes = length; @@ -654,7 +624,7 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req) omap_set_dma_dest_params(ep->lch, OMAP_DMA_PORT_EMIFF, OMAP_DMA_AMODE_POST_INC, req->req.dma + req->req.actual, 0, 0); - ep->dma_counter = DMA_DEST_LAST(ep->lch); + ep->dma_counter = omap_get_dma_dst_pos(ep->lch); UDC_RXDMA_REG(ep->dma_channel) = UDC_RXN_STOP | (packets - 1); UDC_DMA_IRQ_EN_REG |= UDC_RX_EOT_IE(ep->dma_channel); @@ -834,7 +804,7 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) /* channel type P: hw synch (fifo) */ if (cpu_class_is_omap1() && !cpu_is_omap15xx()) - OMAP1_DMA_LCH_CTRL_REG(ep->lch) = 2; + omap_set_dma_channel_mode(ep->lch, OMAP_DMA_LCH_P); } just_restart: @@ -881,7 +851,7 @@ static void dma_channel_release(struct omap_ep *ep) else req = NULL; - active = ((1 << 7) & OMAP_DMA_CCR_REG(ep->lch)) != 0; + active = omap_get_dma_active_status(ep->lch); DBG("%s release %s %cxdma%d %p\n", ep->ep.name, active ? "active" : "idle", -- cgit v1.2.3 From f35ae6346850f6c192269b09088b20261760f0e0 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Thu, 3 Jul 2008 12:24:43 +0300 Subject: ARM: OMAP: USB: Change omap USB code to use omap_read/write instead of __REG Change omap USB code to use omap_read/write instead of __REG for multi-omap Cc: David Brownell Cc: linux-usb@vger.kernel.org Cc: i2c@lm-sensors.org Signed-off-by: Tony Lindgren --- drivers/usb/gadget/omap_udc.c | 468 +++++++++++++++++++++++------------------- drivers/usb/gadget/omap_udc.h | 61 +++--- 2 files changed, 291 insertions(+), 238 deletions(-) (limited to 'drivers/usb/gadget') diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c index 86c029a8d99..03a7f49d207 100644 --- a/drivers/usb/gadget/omap_udc.c +++ b/drivers/usb/gadget/omap_udc.c @@ -135,13 +135,17 @@ static void use_ep(struct omap_ep *ep, u16 select) if (ep->bEndpointAddress & USB_DIR_IN) num |= UDC_EP_DIR; - UDC_EP_NUM_REG = num | select; + omap_writew(num | select, UDC_EP_NUM); /* when select, MUST deselect later !! */ } static inline void deselect_ep(void) { - UDC_EP_NUM_REG &= ~UDC_EP_SEL; + u16 w; + + w = omap_readw(UDC_EP_NUM); + w &= ~UDC_EP_SEL; + omap_writew(w, UDC_EP_NUM); /* 6 wait states before TX will happen */ } @@ -216,7 +220,7 @@ static int omap_ep_enable(struct usb_ep *_ep, ep->has_dma = 0; ep->lch = -1; use_ep(ep, UDC_EP_SEL); - UDC_CTRL_REG = udc->clr_halt; + omap_writew(udc->clr_halt, UDC_CTRL); ep->ackwait = 0; deselect_ep(); @@ -232,7 +236,7 @@ static int omap_ep_enable(struct usb_ep *_ep, if (desc->bmAttributes != USB_ENDPOINT_XFER_ISOC && !ep->has_dma && !(ep->bEndpointAddress & USB_DIR_IN)) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } @@ -259,7 +263,7 @@ static int omap_ep_disable(struct usb_ep *_ep) nuke (ep, -ESHUTDOWN); ep->ep.maxpacket = ep->maxpacket; ep->has_dma = 0; - UDC_CTRL_REG = UDC_SET_HALT; + omap_writew(UDC_SET_HALT, UDC_CTRL); list_del_init(&ep->iso); del_timer(&ep->timer); @@ -360,13 +364,13 @@ write_packet(u8 *buf, struct omap_req *req, unsigned max) if (likely((((int)buf) & 1) == 0)) { wp = (u16 *)buf; while (max >= 2) { - UDC_DATA_REG = *wp++; + omap_writew(*wp++, UDC_DATA); max -= 2; } buf = (u8 *)wp; } while (max--) - *(volatile u8 *)&UDC_DATA_REG = *buf++; + omap_writeb(*buf++, UDC_DATA); return len; } @@ -385,13 +389,13 @@ static int write_fifo(struct omap_ep *ep, struct omap_req *req) prefetch(buf); /* PIO-IN isn't double buffered except for iso */ - ep_stat = UDC_STAT_FLG_REG; + ep_stat = omap_readw(UDC_STAT_FLG); if (ep_stat & UDC_FIFO_UNWRITABLE) return 0; count = ep->ep.maxpacket; count = write_packet(buf, req, count); - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1; /* last packet is often short (sometimes a zlp) */ @@ -425,13 +429,13 @@ read_packet(u8 *buf, struct omap_req *req, unsigned avail) if (likely((((int)buf) & 1) == 0)) { wp = (u16 *)buf; while (avail >= 2) { - *wp++ = UDC_DATA_REG; + *wp++ = omap_readw(UDC_DATA); avail -= 2; } buf = (u8 *)wp; } while (avail--) - *buf++ = *(volatile u8 *)&UDC_DATA_REG; + *buf++ = omap_readb(UDC_DATA); return len; } @@ -446,7 +450,7 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req) prefetchw(buf); for (;;) { - u16 ep_stat = UDC_STAT_FLG_REG; + u16 ep_stat = omap_readw(UDC_STAT_FLG); is_last = 0; if (ep_stat & FIFO_EMPTY) { @@ -460,7 +464,7 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req) if (ep_stat & UDC_FIFO_FULL) avail = ep->ep.maxpacket; else { - avail = UDC_RXFSTAT_REG; + avail = omap_readw(UDC_RXFSTAT); ep->fnf = ep->double_buf; } count = read_packet(buf, req, avail); @@ -473,7 +477,7 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req) req->req.status = -EOVERFLOW; avail -= count; while (avail--) - (void) *(volatile u8 *)&UDC_DATA_REG; + omap_readw(UDC_DATA); } } else if (req->req.length == req->req.actual) is_last = 1; @@ -535,7 +539,7 @@ static u16 dma_dest_len(struct omap_ep *ep, dma_addr_t start) static void next_in_dma(struct omap_ep *ep, struct omap_req *req) { - u16 txdma_ctrl; + u16 txdma_ctrl, w; unsigned length = req->req.length - req->req.actual; const int sync_mode = cpu_is_omap15xx() ? OMAP_DMA_SYNC_FRAME @@ -567,13 +571,17 @@ static void next_in_dma(struct omap_ep *ep, struct omap_req *req) omap_start_dma(ep->lch); ep->dma_counter = omap_get_dma_src_pos(ep->lch); - UDC_DMA_IRQ_EN_REG |= UDC_TX_DONE_IE(ep->dma_channel); - UDC_TXDMA_REG(ep->dma_channel) = UDC_TXN_START | txdma_ctrl; + w = omap_readw(UDC_DMA_IRQ_EN); + w |= UDC_TX_DONE_IE(ep->dma_channel); + omap_writew(w, UDC_DMA_IRQ_EN); + omap_writew(UDC_TXN_START | txdma_ctrl, UDC_TXDMA(ep->dma_channel)); req->dma_bytes = length; } static void finish_in_dma(struct omap_ep *ep, struct omap_req *req, int status) { + u16 w; + if (status == 0) { req->req.actual += req->dma_bytes; @@ -590,7 +598,9 @@ static void finish_in_dma(struct omap_ep *ep, struct omap_req *req, int status) /* tx completion */ omap_stop_dma(ep->lch); - UDC_DMA_IRQ_EN_REG &= ~UDC_TX_DONE_IE(ep->dma_channel); + w = omap_readw(UDC_DMA_IRQ_EN); + w &= ~UDC_TX_DONE_IE(ep->dma_channel); + omap_writew(w, UDC_DMA_IRQ_EN); done(ep, req, status); } @@ -598,6 +608,7 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req) { unsigned packets = req->req.length - req->req.actual; int dma_trigger = 0; + u16 w; if (cpu_is_omap24xx()) dma_trigger = OMAP24XX_DMA(USB_W2FC_RX0, ep->dma_channel); @@ -626,10 +637,12 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req) 0, 0); ep->dma_counter = omap_get_dma_dst_pos(ep->lch); - UDC_RXDMA_REG(ep->dma_channel) = UDC_RXN_STOP | (packets - 1); - UDC_DMA_IRQ_EN_REG |= UDC_RX_EOT_IE(ep->dma_channel); - UDC_EP_NUM_REG = (ep->bEndpointAddress & 0xf); - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_RXN_STOP | (packets - 1), UDC_RXDMA(ep->dma_channel)); + w = omap_readw(UDC_DMA_IRQ_EN); + w |= UDC_RX_EOT_IE(ep->dma_channel); + omap_writew(w, UDC_DMA_IRQ_EN); + omap_writew(ep->bEndpointAddress & 0xf, UDC_EP_NUM); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); omap_start_dma(ep->lch); } @@ -637,7 +650,7 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req) static void finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status, int one) { - u16 count; + u16 count, w; if (status == 0) ep->dma_counter = (u16) (req->req.dma + req->req.actual); @@ -656,13 +669,15 @@ finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status, int one) return; /* rx completion */ - UDC_DMA_IRQ_EN_REG &= ~UDC_RX_EOT_IE(ep->dma_channel); + w = omap_readw(UDC_DMA_IRQ_EN); + w &= ~UDC_RX_EOT_IE(ep->dma_channel); + omap_writew(w, UDC_DMA_IRQ_EN); done(ep, req, status); } static void dma_irq(struct omap_udc *udc, u16 irq_src) { - u16 dman_stat = UDC_DMAN_STAT_REG; + u16 dman_stat = omap_readw(UDC_DMAN_STAT); struct omap_ep *ep; struct omap_req *req; @@ -676,7 +691,7 @@ static void dma_irq(struct omap_udc *udc, u16 irq_src) struct omap_req, queue); finish_in_dma(ep, req, 0); } - UDC_IRQ_SRC_REG = UDC_TXN_DONE; + omap_writew(UDC_TXN_DONE, UDC_IRQ_SRC); if (!list_empty (&ep->queue)) { req = container_of(ep->queue.next, @@ -695,7 +710,7 @@ static void dma_irq(struct omap_udc *udc, u16 irq_src) struct omap_req, queue); finish_out_dma(ep, req, 0, dman_stat & UDC_DMA_RX_SB); } - UDC_IRQ_SRC_REG = UDC_RXN_EOT; + omap_writew(UDC_RXN_EOT, UDC_IRQ_SRC); if (!list_empty (&ep->queue)) { req = container_of(ep->queue.next, @@ -709,7 +724,7 @@ static void dma_irq(struct omap_udc *udc, u16 irq_src) ep->irqs++; /* omap15xx does this unasked... */ VDBG("%s, RX_CNT irq?\n", ep->ep.name); - UDC_IRQ_SRC_REG = UDC_RXN_CNT; + omap_writew(UDC_RXN_CNT, UDC_IRQ_SRC); } } @@ -732,9 +747,9 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) is_in = ep->bEndpointAddress & USB_DIR_IN; if (is_in) - reg = UDC_TXDMA_CFG_REG; + reg = omap_readw(UDC_TXDMA_CFG); else - reg = UDC_RXDMA_CFG_REG; + reg = omap_readw(UDC_RXDMA_CFG); reg |= UDC_DMA_REQ; /* "pulse" activated */ ep->dma_channel = 0; @@ -762,7 +777,7 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) status = omap_request_dma(dma_channel, ep->ep.name, dma_error, ep, &ep->lch); if (status == 0) { - UDC_TXDMA_CFG_REG = reg; + omap_writew(reg, UDC_TXDMA_CFG); /* EMIFF or SDRC */ omap_set_dma_src_burst_mode(ep->lch, OMAP_DMA_DATA_BURST_4); @@ -771,7 +786,7 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) omap_set_dma_dest_params(ep->lch, OMAP_DMA_PORT_TIPB, OMAP_DMA_AMODE_CONSTANT, - (unsigned long) io_v2p((u32)&UDC_DATA_DMA_REG), + (unsigned long) io_v2p(UDC_DATA_DMA), 0, 0); } } else { @@ -783,12 +798,12 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) status = omap_request_dma(dma_channel, ep->ep.name, dma_error, ep, &ep->lch); if (status == 0) { - UDC_RXDMA_CFG_REG = reg; + omap_writew(reg, UDC_RXDMA_CFG); /* TIPB */ omap_set_dma_src_params(ep->lch, OMAP_DMA_PORT_TIPB, OMAP_DMA_AMODE_CONSTANT, - (unsigned long) io_v2p((u32)&UDC_DATA_DMA_REG), + (unsigned long) io_v2p(UDC_DATA_DMA), 0, 0); /* EMIFF or SDRC */ omap_set_dma_dest_burst_mode(ep->lch, @@ -830,7 +845,7 @@ just_restart: (is_in ? write_fifo : read_fifo)(ep, req); deselect_ep(); if (!is_in) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } /* IN: 6 wait states before it'll tx */ @@ -864,23 +879,25 @@ static void dma_channel_release(struct omap_ep *ep) /* wait till current packet DMA finishes, and fifo empties */ if (ep->bEndpointAddress & USB_DIR_IN) { - UDC_TXDMA_CFG_REG = (UDC_TXDMA_CFG_REG & ~mask) | UDC_DMA_REQ; + omap_writew((omap_readw(UDC_TXDMA_CFG) & ~mask) | UDC_DMA_REQ, + UDC_TXDMA_CFG); if (req) { finish_in_dma(ep, req, -ECONNRESET); /* clear FIFO; hosts probably won't empty it */ use_ep(ep, UDC_EP_SEL); - UDC_CTRL_REG = UDC_CLR_EP; + omap_writew(UDC_CLR_EP, UDC_CTRL); deselect_ep(); } - while (UDC_TXDMA_CFG_REG & mask) + while (omap_readw(UDC_TXDMA_CFG) & mask) udelay(10); } else { - UDC_RXDMA_CFG_REG = (UDC_RXDMA_CFG_REG & ~mask) | UDC_DMA_REQ; + omap_writew((omap_readw(UDC_RXDMA_CFG) & ~mask) | UDC_DMA_REQ, + UDC_RXDMA_CFG); /* dma empties the fifo */ - while (UDC_RXDMA_CFG_REG & mask) + while (omap_readw(UDC_RXDMA_CFG) & mask) udelay(10); if (req) finish_out_dma(ep, req, -ECONNRESET, 0); @@ -967,9 +984,13 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) req->req.actual = 0; /* maybe kickstart non-iso i/o queues */ - if (is_iso) - UDC_IRQ_EN_REG |= UDC_SOF_IE; - else if (list_empty(&ep->queue) && !ep->stopped && !ep->ackwait) { + if (is_iso) { + u16 w; + + w = omap_readw(UDC_IRQ_EN); + w |= UDC_SOF_IE; + omap_writew(w, UDC_IRQ_EN); + } else if (list_empty(&ep->queue) && !ep->stopped && !ep->ackwait) { int is_in; if (ep->bEndpointAddress == 0) { @@ -987,23 +1008,23 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) * requests to non-control endpoints */ if (udc->ep0_set_config) { - u16 irq_en = UDC_IRQ_EN_REG; + u16 irq_en = omap_readw(UDC_IRQ_EN); irq_en |= UDC_DS_CHG_IE | UDC_EP0_IE; if (!udc->ep0_reset_config) irq_en |= UDC_EPN_RX_IE | UDC_EPN_TX_IE; - UDC_IRQ_EN_REG = irq_en; + omap_writew(irq_en, UDC_IRQ_EN); } /* STATUS for zero length DATA stages is * always an IN ... even for IN transfers, * a weird case which seem to stall OMAP. */ - UDC_EP_NUM_REG = (UDC_EP_SEL|UDC_EP_DIR); - UDC_CTRL_REG = UDC_CLR_EP; - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_SEL | UDC_EP_DIR, UDC_EP_NUM); + omap_writew(UDC_CLR_EP, UDC_CTRL); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(UDC_EP_DIR, UDC_EP_NUM); /* cleanup */ udc->ep0_pending = 0; @@ -1012,11 +1033,11 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) /* non-empty DATA stage */ } else if (is_in) { - UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; + omap_writew(UDC_EP_SEL | UDC_EP_DIR, UDC_EP_NUM); } else { if (udc->ep0_setup) goto irq_wait; - UDC_EP_NUM_REG = UDC_EP_SEL; + omap_writew(UDC_EP_SEL, UDC_EP_NUM); } } else { is_in = ep->bEndpointAddress & USB_DIR_IN; @@ -1032,7 +1053,7 @@ omap_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) req = NULL; deselect_ep(); if (!is_in) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } /* IN: 6 wait states before it'll tx */ @@ -1100,9 +1121,9 @@ static int omap_ep_set_halt(struct usb_ep *_ep, int value) else if (value) { if (ep->udc->ep0_set_config) { WARN("error changing config?\n"); - UDC_SYSCON2_REG = UDC_CLR_CFG; + omap_writew(UDC_CLR_CFG, UDC_SYSCON2); } - UDC_SYSCON2_REG = UDC_STALL_CMD; + omap_writew(UDC_STALL_CMD, UDC_SYSCON2); ep->udc->ep0_pending = 0; status = 0; } else /* NOP */ @@ -1129,8 +1150,8 @@ static int omap_ep_set_halt(struct usb_ep *_ep, int value) channel = 0; use_ep(ep, UDC_EP_SEL); - if (UDC_STAT_FLG_REG & UDC_NON_ISO_FIFO_EMPTY) { - UDC_CTRL_REG = UDC_SET_HALT; + if (omap_readw(UDC_STAT_FLG) & UDC_NON_ISO_FIFO_EMPTY) { + omap_writew(UDC_SET_HALT, UDC_CTRL); status = 0; } else status = -EAGAIN; @@ -1140,10 +1161,10 @@ static int omap_ep_set_halt(struct usb_ep *_ep, int value) dma_channel_claim(ep, channel); } else { use_ep(ep, 0); - UDC_CTRL_REG = ep->udc->clr_halt; + omap_writew(ep->udc->clr_halt, UDC_CTRL); ep->ackwait = 0; if (!(ep->bEndpointAddress & USB_DIR_IN)) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } } @@ -1175,7 +1196,7 @@ static struct usb_ep_ops omap_ep_ops = { static int omap_get_frame(struct usb_gadget *gadget) { - u16 sof = UDC_SOF_REG; + u16 sof = omap_readw(UDC_SOF); return (sof & UDC_TS_OK) ? (sof & UDC_TS) : -EL2NSYNC; } @@ -1194,7 +1215,7 @@ static int omap_wakeup(struct usb_gadget *gadget) */ if (udc->devstat & (UDC_B_HNP_ENABLE|UDC_R_WK_OK)) { DBG("remote wakeup...\n"); - UDC_SYSCON2_REG = UDC_RMT_WKP; + omap_writew(UDC_RMT_WKP, UDC_SYSCON2); retval = 0; } @@ -1217,12 +1238,12 @@ omap_set_selfpowered(struct usb_gadget *gadget, int is_selfpowered) udc = container_of(gadget, struct omap_udc, gadget); spin_lock_irqsave(&udc->lock, flags); - syscon1 = UDC_SYSCON1_REG; + syscon1 = omap_readw(UDC_SYSCON1); if (is_selfpowered) syscon1 |= UDC_SELF_PWR; else syscon1 &= ~UDC_SELF_PWR; - UDC_SYSCON1_REG = syscon1; + omap_writew(syscon1, UDC_SYSCON1); spin_unlock_irqrestore(&udc->lock, flags); return 0; @@ -1235,18 +1256,36 @@ static int can_pullup(struct omap_udc *udc) static void pullup_enable(struct omap_udc *udc) { - UDC_SYSCON1_REG |= UDC_PULLUP_EN; - if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) - OTG_CTRL_REG |= OTG_BSESSVLD; - UDC_IRQ_EN_REG = UDC_DS_CHG_IE; + u16 w; + + w = omap_readw(UDC_SYSCON1); + w |= UDC_PULLUP_EN; + omap_writew(w, UDC_SYSCON1); + if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) { + u32 l; + + l = omap_readl(OTG_CTRL); + l |= OTG_BSESSVLD; + omap_writel(l, OTG_CTRL); + } + omap_writew(UDC_DS_CHG_IE, UDC_IRQ_EN); } static void pullup_disable(struct omap_udc *udc) { - if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) - OTG_CTRL_REG &= ~OTG_BSESSVLD; - UDC_IRQ_EN_REG = UDC_DS_CHG_IE; - UDC_SYSCON1_REG &= ~UDC_PULLUP_EN; + u16 w; + + if (!gadget_is_otg(&udc->gadget) && !cpu_is_omap15xx()) { + u32 l; + + l = omap_readl(OTG_CTRL); + l &= ~OTG_BSESSVLD; + omap_writel(l, OTG_CTRL); + } + omap_writew(UDC_DS_CHG_IE, UDC_IRQ_EN); + w = omap_readw(UDC_SYSCON1); + w &= ~UDC_PULLUP_EN; + omap_writew(w, UDC_SYSCON1); } static struct omap_udc *udc; @@ -1274,6 +1313,7 @@ static int omap_vbus_session(struct usb_gadget *gadget, int is_active) { struct omap_udc *udc; unsigned long flags; + u32 l; udc = container_of(gadget, struct omap_udc, gadget); spin_lock_irqsave(&udc->lock, flags); @@ -1281,10 +1321,12 @@ static int omap_vbus_session(struct usb_gadget *gadget, int is_active) udc->vbus_active = (is_active != 0); if (cpu_is_omap15xx()) { /* "software" detect, ignored if !VBUS_MODE_1510 */ + l = omap_readl(FUNC_MUX_CTRL_0); if (is_active) - FUNC_MUX_CTRL_0_REG |= VBUS_CTRL_1510; + l |= VBUS_CTRL_1510; else - FUNC_MUX_CTRL_0_REG &= ~VBUS_CTRL_1510; + l &= ~VBUS_CTRL_1510; + omap_writel(l, FUNC_MUX_CTRL_0); } if (udc->dc_clk != NULL && is_active) { if (!udc->clk_requested) { @@ -1354,9 +1396,9 @@ static void nuke(struct omap_ep *ep, int status) dma_channel_release(ep); use_ep(ep, 0); - UDC_CTRL_REG = UDC_CLR_EP; + omap_writew(UDC_CLR_EP, UDC_CTRL); if (ep->bEndpointAddress && ep->bmAttributes != USB_ENDPOINT_XFER_ISOC) - UDC_CTRL_REG = UDC_SET_HALT; + omap_writew(UDC_SET_HALT, UDC_CTRL); while (!list_empty(&ep->queue)) { req = list_entry(ep->queue.next, struct omap_req, queue); @@ -1384,8 +1426,8 @@ static void update_otg(struct omap_udc *udc) if (!gadget_is_otg(&udc->gadget)) return; - if (OTG_CTRL_REG & OTG_ID) - devstat = UDC_DEVSTAT_REG; + if (omap_readl(OTG_CTRL) & OTG_ID) + devstat = omap_readw(UDC_DEVSTAT); else devstat = 0; @@ -1396,9 +1438,14 @@ static void update_otg(struct omap_udc *udc) /* Enable HNP early, avoiding races on suspend irq path. * ASSUMES OTG state machine B_BUS_REQ input is true. */ - if (udc->gadget.b_hnp_enable) - OTG_CTRL_REG = (OTG_CTRL_REG | OTG_B_HNPEN | OTG_B_BUSREQ) - & ~OTG_PULLUP; + if (udc->gadget.b_hnp_enable) { + u32 l; + + l = omap_readl(OTG_CTRL); + l |= OTG_B_HNPEN | OTG_B_BUSREQ; + l &= ~OTG_PULLUP; + omap_writel(l, OTG_CTRL); + } } static void ep0_irq(struct omap_udc *udc, u16 irq_src) @@ -1416,7 +1463,7 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) nuke(ep0, 0); if (ack) { - UDC_IRQ_SRC_REG = ack; + omap_writew(ack, UDC_IRQ_SRC); irq_src = UDC_SETUP; } } @@ -1436,9 +1483,9 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) if (irq_src & UDC_EP0_TX) { int stat; - UDC_IRQ_SRC_REG = UDC_EP0_TX; - UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; - stat = UDC_STAT_FLG_REG; + omap_writew(UDC_EP0_TX, UDC_IRQ_SRC); + omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM); + stat = omap_readw(UDC_STAT_FLG); if (stat & UDC_ACK) { if (udc->ep0_in) { /* write next IN packet from response, @@ -1446,26 +1493,26 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) */ if (req) stat = write_fifo(ep0, req); - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_DIR, UDC_EP_NUM); if (!req && udc->ep0_pending) { - UDC_EP_NUM_REG = UDC_EP_SEL; - UDC_CTRL_REG = UDC_CLR_EP; - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = 0; + omap_writew(UDC_EP_SEL, UDC_EP_NUM); + omap_writew(UDC_CLR_EP, UDC_CTRL); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(0, UDC_EP_NUM); udc->ep0_pending = 0; } /* else: 6 wait states before it'll tx */ } else { /* ack status stage of OUT transfer */ - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_DIR, UDC_EP_NUM); if (req) done(ep0, req, 0); } req = NULL; } else if (stat & UDC_STALL) { - UDC_CTRL_REG = UDC_CLR_HALT; - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_CLR_HALT, UDC_CTRL); + omap_writew(UDC_EP_DIR, UDC_EP_NUM); } else { - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_DIR, UDC_EP_NUM); } } @@ -1473,9 +1520,9 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) if (irq_src & UDC_EP0_RX) { int stat; - UDC_IRQ_SRC_REG = UDC_EP0_RX; - UDC_EP_NUM_REG = UDC_EP_SEL; - stat = UDC_STAT_FLG_REG; + omap_writew(UDC_EP0_RX, UDC_IRQ_SRC); + omap_writew(UDC_EP_SEL, UDC_EP_NUM); + stat = omap_readw(UDC_STAT_FLG); if (stat & UDC_ACK) { if (!udc->ep0_in) { stat = 0; @@ -1483,34 +1530,35 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) * reactiviting the fifo; stall on errors. */ if (!req || (stat = read_fifo(ep0, req)) < 0) { - UDC_SYSCON2_REG = UDC_STALL_CMD; + omap_writew(UDC_STALL_CMD, UDC_SYSCON2); udc->ep0_pending = 0; stat = 0; } else if (stat == 0) - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = 0; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(0, UDC_EP_NUM); /* activate status stage */ if (stat == 1) { done(ep0, req, 0); /* that may have STALLed ep0... */ - UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; - UDC_CTRL_REG = UDC_CLR_EP; - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_SEL | UDC_EP_DIR, + UDC_EP_NUM); + omap_writew(UDC_CLR_EP, UDC_CTRL); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(UDC_EP_DIR, UDC_EP_NUM); udc->ep0_pending = 0; } } else { /* ack status stage of IN transfer */ - UDC_EP_NUM_REG = 0; + omap_writew(0, UDC_EP_NUM); if (req) done(ep0, req, 0); } } else if (stat & UDC_STALL) { - UDC_CTRL_REG = UDC_CLR_HALT; - UDC_EP_NUM_REG = 0; + omap_writew(UDC_CLR_HALT, UDC_CTRL); + omap_writew(0, UDC_EP_NUM); } else { - UDC_EP_NUM_REG = 0; + omap_writew(0, UDC_EP_NUM); } } @@ -1525,14 +1573,14 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) /* read the (latest) SETUP message */ do { - UDC_EP_NUM_REG = UDC_SETUP_SEL; + omap_writew(UDC_SETUP_SEL, UDC_EP_NUM); /* two bytes at a time */ - u.word[0] = UDC_DATA_REG; - u.word[1] = UDC_DATA_REG; - u.word[2] = UDC_DATA_REG; - u.word[3] = UDC_DATA_REG; - UDC_EP_NUM_REG = 0; - } while (UDC_IRQ_SRC_REG & UDC_SETUP); + u.word[0] = omap_readw(UDC_DATA); + u.word[1] = omap_readw(UDC_DATA); + u.word[2] = omap_readw(UDC_DATA); + u.word[3] = omap_readw(UDC_DATA); + omap_writew(0, UDC_EP_NUM); + } while (omap_readw(UDC_IRQ_SRC) & UDC_SETUP); #define w_value le16_to_cpu(u.r.wValue) #define w_index le16_to_cpu(u.r.wIndex) @@ -1563,9 +1611,9 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) * later if it fails the request. */ if (udc->ep0_reset_config) - UDC_SYSCON2_REG = UDC_CLR_CFG; + omap_writew(UDC_CLR_CFG, UDC_SYSCON2); else - UDC_SYSCON2_REG = UDC_DEV_CFG; + omap_writew(UDC_DEV_CFG, UDC_SYSCON2); update_otg(udc); goto delegate; case USB_REQ_CLEAR_FEATURE: @@ -1583,10 +1631,10 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) || !ep->desc) goto do_stall; use_ep(ep, 0); - UDC_CTRL_REG = udc->clr_halt; + omap_writew(udc->clr_halt, UDC_CTRL); ep->ackwait = 0; if (!(ep->bEndpointAddress & USB_DIR_IN)) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } /* NOTE: assumes the host behaves sanely, @@ -1619,15 +1667,15 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) } use_ep(ep, 0); /* can't halt if fifo isn't empty... */ - UDC_CTRL_REG = UDC_CLR_EP; - UDC_CTRL_REG = UDC_SET_HALT; + omap_writew(UDC_CLR_EP, UDC_CTRL); + omap_writew(UDC_SET_HALT, UDC_CTRL); VDBG("%s halted by host\n", ep->name); ep0out_status_stage: status = 0; - UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; - UDC_CTRL_REG = UDC_CLR_EP; - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM); + omap_writew(UDC_CLR_EP, UDC_CTRL); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(UDC_EP_DIR, UDC_EP_NUM); udc->ep0_pending = 0; break; case USB_REQ_GET_STATUS: @@ -1664,10 +1712,10 @@ intf_status: zero_status: /* return two zero bytes */ - UDC_EP_NUM_REG = UDC_EP_SEL|UDC_EP_DIR; - UDC_DATA_REG = 0; - UDC_CTRL_REG = UDC_SET_FIFO_EN; - UDC_EP_NUM_REG = UDC_EP_DIR; + omap_writew(UDC_EP_SEL|UDC_EP_DIR, UDC_EP_NUM); + omap_writew(0, UDC_DATA); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); + omap_writew(UDC_EP_DIR, UDC_EP_NUM); status = 0; VDBG("GET_STATUS, interface %d\n", w_index); /* next, status stage */ @@ -1676,8 +1724,8 @@ zero_status: delegate: /* activate the ep0out fifo right away */ if (!udc->ep0_in && w_length) { - UDC_EP_NUM_REG = 0; - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(0, UDC_EP_NUM); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); } /* gadget drivers see class/vendor specific requests, @@ -1718,9 +1766,9 @@ do_stall: if (udc->ep0_reset_config) WARN("error resetting config?\n"); else - UDC_SYSCON2_REG = UDC_CLR_CFG; + omap_writew(UDC_CLR_CFG, UDC_SYSCON2); } - UDC_SYSCON2_REG = UDC_STALL_CMD; + omap_writew(UDC_STALL_CMD, UDC_SYSCON2); udc->ep0_pending = 0; } } @@ -1734,7 +1782,7 @@ static void devstate_irq(struct omap_udc *udc, u16 irq_src) { u16 devstat, change; - devstat = UDC_DEVSTAT_REG; + devstat = omap_readw(UDC_DEVSTAT); change = devstat ^ udc->devstat; udc->devstat = devstat; @@ -1774,7 +1822,8 @@ static void devstate_irq(struct omap_udc *udc, u16 irq_src) INFO("USB reset done, gadget %s\n", udc->driver->driver.name); /* ep0 traffic is legal from now on */ - UDC_IRQ_EN_REG = UDC_DS_CHG_IE | UDC_EP0_IE; + omap_writew(UDC_DS_CHG_IE | UDC_EP0_IE, + UDC_IRQ_EN); } change &= ~UDC_USB_RESET; } @@ -1818,7 +1867,7 @@ static void devstate_irq(struct omap_udc *udc, u16 irq_src) VDBG("devstat %03x, ignore change %03x\n", devstat, change); - UDC_IRQ_SRC_REG = UDC_DS_CHG; + omap_writew(UDC_DS_CHG, UDC_IRQ_SRC); } static irqreturn_t omap_udc_irq(int irq, void *_udc) @@ -1829,7 +1878,7 @@ static irqreturn_t omap_udc_irq(int irq, void *_udc) unsigned long flags; spin_lock_irqsave(&udc->lock, flags); - irq_src = UDC_IRQ_SRC_REG; + irq_src = omap_readw(UDC_IRQ_SRC); /* Device state change (usb ch9 stuff) */ if (irq_src & UDC_DS_CHG) { @@ -1852,7 +1901,7 @@ static irqreturn_t omap_udc_irq(int irq, void *_udc) irq_src &= ~(UDC_TXN_DONE|UDC_RXN_CNT|UDC_RXN_EOT); } - irq_src &= ~(UDC_SOF|UDC_EPN_TX|UDC_EPN_RX); + irq_src &= ~(UDC_IRQ_SOF | UDC_EPN_TX|UDC_EPN_RX); if (irq_src) DBG("udc_irq, unhandled %03x\n", irq_src); spin_unlock_irqrestore(&udc->lock, flags); @@ -1873,7 +1922,7 @@ static void pio_out_timer(unsigned long _ep) spin_lock_irqsave(&ep->udc->lock, flags); if (!list_empty(&ep->queue) && ep->ackwait) { use_ep(ep, UDC_EP_SEL); - stat_flg = UDC_STAT_FLG_REG; + stat_flg = omap_readw(UDC_STAT_FLG); if ((stat_flg & UDC_ACK) && (!(stat_flg & UDC_FIFO_EN) || (ep->double_buf && HALF_FULL(stat_flg)))) { @@ -1883,8 +1932,8 @@ static void pio_out_timer(unsigned long _ep) req = container_of(ep->queue.next, struct omap_req, queue); (void) read_fifo(ep, req); - UDC_EP_NUM_REG = ep->bEndpointAddress; - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(ep->bEndpointAddress, UDC_EP_NUM); + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } else deselect_ep(); @@ -1904,20 +1953,20 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev) unsigned long flags; spin_lock_irqsave(&udc->lock, flags); - epn_stat = UDC_EPN_STAT_REG; - irq_src = UDC_IRQ_SRC_REG; + epn_stat = omap_readw(UDC_EPN_STAT); + irq_src = omap_readw(UDC_IRQ_SRC); /* handle OUT first, to avoid some wasteful NAKs */ if (irq_src & UDC_EPN_RX) { epnum = (epn_stat >> 8) & 0x0f; - UDC_IRQ_SRC_REG = UDC_EPN_RX; + omap_writew(UDC_EPN_RX, UDC_IRQ_SRC); status = IRQ_HANDLED; ep = &udc->ep[epnum]; ep->irqs++; - UDC_EP_NUM_REG = epnum | UDC_EP_SEL; + omap_writew(epnum | UDC_EP_SEL, UDC_EP_NUM); ep->fnf = 0; - if ((UDC_STAT_FLG_REG & UDC_ACK)) { + if (omap_readw(UDC_STAT_FLG) & UDC_ACK) { ep->ackwait--; if (!list_empty(&ep->queue)) { int stat; @@ -1929,15 +1978,15 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev) } } /* min 6 clock delay before clearing EP_SEL ... */ - epn_stat = UDC_EPN_STAT_REG; - epn_stat = UDC_EPN_STAT_REG; - UDC_EP_NUM_REG = epnum; + epn_stat = omap_readw(UDC_EPN_STAT); + epn_stat = omap_readw(UDC_EPN_STAT); + omap_writew(epnum, UDC_EP_NUM); /* enabling fifo _after_ clearing ACK, contrary to docs, * reduces lossage; timer still needed though (sigh). */ if (ep->fnf) { - UDC_CTRL_REG = UDC_SET_FIFO_EN; + omap_writew(UDC_SET_FIFO_EN, UDC_CTRL); ep->ackwait = 1 + ep->double_buf; } mod_timer(&ep->timer, PIO_OUT_TIMEOUT); @@ -1946,13 +1995,13 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev) /* then IN transfers */ else if (irq_src & UDC_EPN_TX) { epnum = epn_stat & 0x0f; - UDC_IRQ_SRC_REG = UDC_EPN_TX; + omap_writew(UDC_EPN_TX, UDC_IRQ_SRC); status = IRQ_HANDLED; ep = &udc->ep[16 + epnum]; ep->irqs++; - UDC_EP_NUM_REG = epnum | UDC_EP_DIR | UDC_EP_SEL; - if ((UDC_STAT_FLG_REG & UDC_ACK)) { + omap_writew(epnum | UDC_EP_DIR | UDC_EP_SEL, UDC_EP_NUM); + if (omap_readw(UDC_STAT_FLG) & UDC_ACK) { ep->ackwait = 0; if (!list_empty(&ep->queue)) { req = container_of(ep->queue.next, @@ -1961,9 +2010,9 @@ static irqreturn_t omap_udc_pio_irq(int irq, void *_dev) } } /* min 6 clock delay before clearing EP_SEL ... */ - epn_stat = UDC_EPN_STAT_REG; - epn_stat = UDC_EPN_STAT_REG; - UDC_EP_NUM_REG = epnum | UDC_EP_DIR; + epn_stat = omap_readw(UDC_EPN_STAT); + epn_stat = omap_readw(UDC_EPN_STAT); + omap_writew(epnum | UDC_EP_DIR, UDC_EP_NUM); /* then 6 clocks before it'd tx */ } @@ -1991,7 +2040,7 @@ static irqreturn_t omap_udc_iso_irq(int irq, void *_dev) req = list_entry(ep->queue.next, struct omap_req, queue); use_ep(ep, UDC_EP_SEL); - stat = UDC_STAT_FLG_REG; + stat = omap_readw(UDC_STAT_FLG); /* NOTE: like the other controller drivers, this isn't * currently reporting lost or damaged frames. @@ -2023,9 +2072,14 @@ static irqreturn_t omap_udc_iso_irq(int irq, void *_dev) if (!list_empty(&ep->queue)) pending = 1; } - if (!pending) - UDC_IRQ_EN_REG &= ~UDC_SOF_IE; - UDC_IRQ_SRC_REG = UDC_SOF; + if (!pending) { + u16 w; + + w = omap_readw(UDC_IRQ_EN); + w &= ~UDC_SOF_IE; + omap_writew(w, UDC_IRQ_EN); + } + omap_writew(UDC_IRQ_SOF, UDC_IRQ_SRC); spin_unlock_irqrestore(&udc->lock, flags); return IRQ_HANDLED; @@ -2074,7 +2128,7 @@ int usb_gadget_register_driver (struct usb_gadget_driver *driver) if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) continue; use_ep(ep, 0); - UDC_CTRL_REG = UDC_SET_HALT; + omap_writew(UDC_SET_HALT, UDC_CTRL); } udc->ep0_pending = 0; udc->ep[0].irqs = 0; @@ -2098,7 +2152,7 @@ int usb_gadget_register_driver (struct usb_gadget_driver *driver) } DBG("bound to driver %s\n", driver->driver.name); - UDC_IRQ_SRC_REG = UDC_IRQ_SRC_MASK; + omap_writew(UDC_IRQ_SRC_MASK, UDC_IRQ_SRC); /* connect to bus through transceiver */ if (udc->transceiver) { @@ -2195,7 +2249,7 @@ static void proc_ep_show(struct seq_file *s, struct omap_ep *ep) else buf[0] = 0; - stat_flg = UDC_STAT_FLG_REG; + stat_flg = omap_readw(UDC_STAT_FLG); seq_printf(s, "\n%s %s%s%sirqs %ld stat %04x " EIGHTBITS FOURBITS "%s\n", ep->name, buf, @@ -2262,11 +2316,11 @@ static int proc_otg_show(struct seq_file *s) trans = CONTROL_DEVCONF_REG; } else { ctrl_name = "tranceiver_ctrl"; - trans = USB_TRANSCEIVER_CTRL_REG; + trans = omap_readw(USB_TRANSCEIVER_CTRL); } seq_printf(s, "\nOTG rev %d.%d, %s %05x\n", tmp >> 4, tmp & 0xf, ctrl_name, trans); - tmp = OTG_SYSCON_1_REG; + tmp = omap_readw(OTG_SYSCON_1); seq_printf(s, "otg_syscon1 %08x usb2 %s, usb1 %s, usb0 %s," FOURBITS "\n", tmp, trx_mode(USB2_TRX_MODE(tmp), trans & CONF_USB2_UNI_R), @@ -2278,7 +2332,7 @@ static int proc_otg_show(struct seq_file *s) (tmp & HST_IDLE_EN) ? " !host" : "", (tmp & DEV_IDLE_EN) ? " !dev" : "", (tmp & OTG_RESET_DONE) ? " reset_done" : " reset_active"); - tmp = OTG_SYSCON_2_REG; + tmp = omap_readl(OTG_SYSCON_2); seq_printf(s, "otg_syscon2 %08x%s" EIGHTBITS " b_ase_brst=%d hmc=%d\n", tmp, (tmp & OTG_EN) ? " otg_en" : "", @@ -2293,7 +2347,7 @@ static int proc_otg_show(struct seq_file *s) (tmp & HMC_TLLATTACH) ? " tllattach" : "", B_ASE_BRST(tmp), OTG_HMC(tmp)); - tmp = OTG_CTRL_REG; + tmp = omap_readl(OTG_CTRL); seq_printf(s, "otg_ctrl %06x" EIGHTBITS EIGHTBITS "%s\n", tmp, (tmp & OTG_ASESSVLD) ? " asess" : "", (tmp & OTG_BSESSEND) ? " bsess_end" : "", @@ -2313,13 +2367,13 @@ static int proc_otg_show(struct seq_file *s) (tmp & OTG_PU_VBUS) ? " pu_vb" : "", (tmp & OTG_PU_ID) ? " pu_id" : "" ); - tmp = OTG_IRQ_EN_REG; + tmp = omap_readw(OTG_IRQ_EN); seq_printf(s, "otg_irq_en %04x" "\n", tmp); - tmp = OTG_IRQ_SRC_REG; + tmp = omap_readw(OTG_IRQ_SRC); seq_printf(s, "otg_irq_src %04x" "\n", tmp); - tmp = OTG_OUTCTRL_REG; + tmp = omap_readw(OTG_OUTCTRL); seq_printf(s, "otg_outctrl %04x" "\n", tmp); - tmp = OTG_TEST_REG; + tmp = omap_readw(OTG_TEST); seq_printf(s, "otg_test %04x" "\n", tmp); return 0; } @@ -2340,7 +2394,7 @@ static int proc_udc_show(struct seq_file *s, void *_) driver_desc, use_dma ? " (dma)" : ""); - tmp = UDC_REV_REG & 0xff; + tmp = omap_readw(UDC_REV) & 0xff; seq_printf(s, "UDC rev %d.%d, fifo mode %d, gadget %s\n" "hmc %d, transceiver %s\n", @@ -2354,16 +2408,16 @@ static int proc_udc_show(struct seq_file *s, void *_) ? "external" : "(none)")); if (cpu_class_is_omap1()) { seq_printf(s, "ULPD control %04x req %04x status %04x\n", - __REG16(ULPD_CLOCK_CTRL), - __REG16(ULPD_SOFT_REQ), - __REG16(ULPD_STATUS_REQ)); + omap_readw(ULPD_CLOCK_CTRL), + omap_readw(ULPD_SOFT_REQ), + omap_readw(ULPD_STATUS_REQ)); } /* OTG controller registers */ if (!cpu_is_omap15xx()) proc_otg_show(s); - tmp = UDC_SYSCON1_REG; + tmp = omap_readw(UDC_SYSCON1); seq_printf(s, "\nsyscon1 %04x" EIGHTBITS "\n", tmp, (tmp & UDC_CFG_LOCK) ? " cfg_lock" : "", (tmp & UDC_DATA_ENDIAN) ? " data_endian" : "", @@ -2382,7 +2436,7 @@ static int proc_udc_show(struct seq_file *s, void *_) return 0; } - tmp = UDC_DEVSTAT_REG; + tmp = omap_readw(UDC_DEVSTAT); seq_printf(s, "devstat %04x" EIGHTBITS "%s%s\n", tmp, (tmp & UDC_B_HNP_ENABLE) ? " b_hnp" : "", (tmp & UDC_A_HNP_SUPPORT) ? " a_hnp" : "", @@ -2394,20 +2448,20 @@ static int proc_udc_show(struct seq_file *s, void *_) (tmp & UDC_ADD) ? " ADD" : "", (tmp & UDC_DEF) ? " DEF" : "", (tmp & UDC_ATT) ? " ATT" : ""); - seq_printf(s, "sof %04x\n", UDC_SOF_REG); - tmp = UDC_IRQ_EN_REG; + seq_printf(s, "sof %04x\n", omap_readw(UDC_SOF)); + tmp = omap_readw(UDC_IRQ_EN); seq_printf(s, "irq_en %04x" FOURBITS "%s\n", tmp, (tmp & UDC_SOF_IE) ? " sof" : "", (tmp & UDC_EPN_RX_IE) ? " epn_rx" : "", (tmp & UDC_EPN_TX_IE) ? " epn_tx" : "", (tmp & UDC_DS_CHG_IE) ? " ds_chg" : "", (tmp & UDC_EP0_IE) ? " ep0" : ""); - tmp = UDC_IRQ_SRC_REG; + tmp = omap_readw(UDC_IRQ_SRC); seq_printf(s, "irq_src %04x" EIGHTBITS "%s%s\n", tmp, (tmp & UDC_TXN_DONE) ? " txn_done" : "", (tmp & UDC_RXN_CNT) ? " rxn_cnt" : "", (tmp & UDC_RXN_EOT) ? " rxn_eot" : "", - (tmp & UDC_SOF) ? " sof" : "", + (tmp & UDC_IRQ_SOF) ? " sof" : "", (tmp & UDC_EPN_RX) ? " epn_rx" : "", (tmp & UDC_EPN_TX) ? " epn_tx" : "", (tmp & UDC_DS_CHG) ? " ds_chg" : "", @@ -2417,7 +2471,7 @@ static int proc_udc_show(struct seq_file *s, void *_) if (use_dma) { unsigned i; - tmp = UDC_DMA_IRQ_EN_REG; + tmp = omap_readw(UDC_DMA_IRQ_EN); seq_printf(s, "dma_irq_en %04x%s" EIGHTBITS "\n", tmp, (tmp & UDC_TX_DONE_IE(3)) ? " tx2_done" : "", (tmp & UDC_RX_CNT_IE(3)) ? " rx2_cnt" : "", @@ -2431,29 +2485,29 @@ static int proc_udc_show(struct seq_file *s, void *_) (tmp & UDC_RX_CNT_IE(1)) ? " rx0_cnt" : "", (tmp & UDC_RX_EOT_IE(1)) ? " rx0_eot" : ""); - tmp = UDC_RXDMA_CFG_REG; + tmp = omap_readw(UDC_RXDMA_CFG); seq_printf(s, "rxdma_cfg %04x\n", tmp); if (tmp) { for (i = 0; i < 3; i++) { if ((tmp & (0x0f << (i * 4))) == 0) continue; seq_printf(s, "rxdma[%d] %04x\n", i, - UDC_RXDMA_REG(i + 1)); + omap_readw(UDC_RXDMA(i + 1))); } } - tmp = UDC_TXDMA_CFG_REG; + tmp = omap_readw(UDC_TXDMA_CFG); seq_printf(s, "txdma_cfg %04x\n", tmp); if (tmp) { for (i = 0; i < 3; i++) { if (!(tmp & (0x0f << (i * 4)))) continue; seq_printf(s, "txdma[%d] %04x\n", i, - UDC_TXDMA_REG(i + 1)); + omap_readw(UDC_TXDMA(i + 1))); } } } - tmp = UDC_DEVSTAT_REG; + tmp = omap_readw(UDC_DEVSTAT); if (tmp & UDC_ATT) { proc_ep_show(s, &udc->ep[0]); if (tmp & UDC_ADD) { @@ -2505,7 +2559,7 @@ static inline void remove_proc_file(void) {} * buffer space among the endpoints we'll be operating. * * NOTE: as of OMAP 1710 ES2.0, writing a new endpoint config when - * UDC_SYSCON_1_REG.CFG_LOCK is set can now work. We won't use that + * UDC_SYSCON_1.CFG_LOCK is set can now work. We won't use that * capability yet though. */ static unsigned __init @@ -2567,9 +2621,9 @@ omap_ep_setup(char *name, u8 addr, u8 type, name, addr, epn_rxtx, maxp, dbuf ? "x2" : "", buf); if (addr & USB_DIR_IN) - UDC_EP_TX_REG(addr & 0xf) = epn_rxtx; + omap_writew(epn_rxtx, UDC_EP_TX(addr & 0xf)); else - UDC_EP_RX_REG(addr) = epn_rxtx; + omap_writew(epn_rxtx, UDC_EP_RX(addr)); /* next endpoint's buffer starts after this one's */ buf += maxp; @@ -2608,15 +2662,15 @@ omap_udc_setup(struct platform_device *odev, struct otg_transceiver *xceiv) unsigned tmp, buf; /* abolish any previous hardware state */ - UDC_SYSCON1_REG = 0; - UDC_IRQ_EN_REG = 0; - UDC_IRQ_SRC_REG = UDC_IRQ_SRC_MASK; - UDC_DMA_IRQ_EN_REG = 0; - UDC_RXDMA_CFG_REG = 0; - UDC_TXDMA_CFG_REG = 0; + omap_writew(0, UDC_SYSCON1); + omap_writew(0, UDC_IRQ_EN); + omap_writew(UDC_IRQ_SRC_MASK, UDC_IRQ_SRC); + omap_writew(0, UDC_DMA_IRQ_EN); + omap_writew(0, UDC_RXDMA_CFG); + omap_writew(0, UDC_TXDMA_CFG); /* UDC_PULLUP_EN gates the chip clock */ - // OTG_SYSCON_1_REG |= DEV_IDLE_EN; + // OTG_SYSCON_1 |= DEV_IDLE_EN; udc = kzalloc(sizeof(*udc), GFP_KERNEL); if (!udc) @@ -2647,8 +2701,8 @@ omap_udc_setup(struct platform_device *odev, struct otg_transceiver *xceiv) /* initially disable all non-ep0 endpoints */ for (tmp = 1; tmp < 15; tmp++) { - UDC_EP_RX_REG(tmp) = 0; - UDC_EP_TX_REG(tmp) = 0; + omap_writew(0, UDC_EP_RX(tmp)); + omap_writew(0, UDC_EP_TX(tmp)); } #define OMAP_BULK_EP(name,addr) \ @@ -2733,7 +2787,7 @@ omap_udc_setup(struct platform_device *odev, struct otg_transceiver *xceiv) ERR("unsupported fifo_mode #%d\n", fifo_mode); return -ENODEV; } - UDC_SYSCON1_REG = UDC_CFG_LOCK|UDC_SELF_PWR; + omap_writew(UDC_CFG_LOCK|UDC_SELF_PWR, UDC_SYSCON1); INFO("fifo mode %d, %d bytes not used\n", fifo_mode, 2048 - buf); return 0; } @@ -2777,7 +2831,7 @@ static int __init omap_udc_probe(struct platform_device *pdev) } INFO("OMAP UDC rev %d.%d%s\n", - UDC_REV_REG >> 4, UDC_REV_REG & 0xf, + omap_readw(UDC_REV) >> 4, omap_readw(UDC_REV) & 0xf, config->otg ? ", Mini-AB" : ""); /* use the mode given to us by board init code */ @@ -2792,12 +2846,12 @@ static int __init omap_udc_probe(struct platform_device *pdev) * know when to turn PULLUP_EN on/off; and that * means we always "need" the 48MHz clock. */ - u32 tmp = FUNC_MUX_CTRL_0_REG; - - FUNC_MUX_CTRL_0_REG &= ~VBUS_CTRL_1510; + u32 tmp = omap_readl(FUNC_MUX_CTRL_0); + tmp &= ~VBUS_CTRL_1510; + omap_writel(tmp, FUNC_MUX_CTRL_0); tmp |= VBUS_MODE_1510; tmp &= ~VBUS_CTRL_1510; - FUNC_MUX_CTRL_0_REG = tmp; + omap_writel(tmp, FUNC_MUX_CTRL_0); } } else { /* The transceiver may package some GPIO logic or handle @@ -2877,7 +2931,7 @@ known: #endif /* starting with omap1710 es2.0, clear toggle is a separate bit */ - if (UDC_REV_REG >= 0x61) + if (omap_readw(UDC_REV) >= 0x61) udc->clr_halt = UDC_RESET_EP | UDC_CLRDATA_TOGGLE; else udc->clr_halt = UDC_RESET_EP; @@ -2975,7 +3029,7 @@ static int __exit omap_udc_remove(struct platform_device *pdev) put_device(udc->transceiver->dev); udc->transceiver = NULL; } - UDC_SYSCON1_REG = 0; + omap_writew(0, UDC_SYSCON1); remove_proc_file(); @@ -3006,7 +3060,7 @@ static int __exit omap_udc_remove(struct platform_device *pdev) * * REVISIT we should probably reject suspend requests when there's a host * session active, rather than disconnecting, at least on boards that can - * report VBUS irqs (UDC_DEVSTAT_REG.UDC_ATT). And in any case, we need to + * report VBUS irqs (UDC_DEVSTAT.UDC_ATT). And in any case, we need to * make host resumes and VBUS detection trigger OMAP wakeup events; that * may involve talking to an external transceiver (e.g. isp1301). */ @@ -3015,7 +3069,7 @@ static int omap_udc_suspend(struct platform_device *dev, pm_message_t message) { u32 devstat; - devstat = UDC_DEVSTAT_REG; + devstat = omap_readw(UDC_DEVSTAT); /* we're requesting 48 MHz clock if the pullup is enabled * (== we're attached to the host) and we're not suspended, diff --git a/drivers/usb/gadget/omap_udc.h b/drivers/usb/gadget/omap_udc.h index c6b9cbc7230..8522bbb1227 100644 --- a/drivers/usb/gadget/omap_udc.h +++ b/drivers/usb/gadget/omap_udc.h @@ -8,23 +8,22 @@ /* * USB device/endpoint management registers */ -#define UDC_REG(offset) __REG16(UDC_BASE + (offset)) -#define UDC_REV_REG UDC_REG(0x0) /* Revision */ -#define UDC_EP_NUM_REG UDC_REG(0x4) /* Which endpoint */ +#define UDC_REV (UDC_BASE + 0x0) /* Revision */ +#define UDC_EP_NUM (UDC_BASE + 0x4) /* Which endpoint */ # define UDC_SETUP_SEL (1 << 6) # define UDC_EP_SEL (1 << 5) # define UDC_EP_DIR (1 << 4) /* low 4 bits for endpoint number */ -#define UDC_DATA_REG UDC_REG(0x08) /* Endpoint FIFO */ -#define UDC_CTRL_REG UDC_REG(0x0C) /* Endpoint control */ +#define UDC_DATA (UDC_BASE + 0x08) /* Endpoint FIFO */ +#define UDC_CTRL (UDC_BASE + 0x0C) /* Endpoint control */ # define UDC_CLR_HALT (1 << 7) # define UDC_SET_HALT (1 << 6) # define UDC_CLRDATA_TOGGLE (1 << 3) # define UDC_SET_FIFO_EN (1 << 2) # define UDC_CLR_EP (1 << 1) # define UDC_RESET_EP (1 << 0) -#define UDC_STAT_FLG_REG UDC_REG(0x10) /* Endpoint status */ +#define UDC_STAT_FLG (UDC_BASE + 0x10) /* Endpoint status */ # define UDC_NO_RXPACKET (1 << 15) # define UDC_MISS_IN (1 << 14) # define UDC_DATA_FLUSH (1 << 13) @@ -38,8 +37,8 @@ # define UDC_FIFO_EN (1 << 2) # define UDC_NON_ISO_FIFO_EMPTY (1 << 1) # define UDC_NON_ISO_FIFO_FULL (1 << 0) -#define UDC_RXFSTAT_REG UDC_REG(0x14) /* OUT bytecount */ -#define UDC_SYSCON1_REG UDC_REG(0x18) /* System config 1 */ +#define UDC_RXFSTAT (UDC_BASE + 0x14) /* OUT bytecount */ +#define UDC_SYSCON1 (UDC_BASE + 0x18) /* System config 1 */ # define UDC_CFG_LOCK (1 << 8) # define UDC_DATA_ENDIAN (1 << 7) # define UDC_DMA_ENDIAN (1 << 6) @@ -48,12 +47,12 @@ # define UDC_SELF_PWR (1 << 2) # define UDC_SOFF_DIS (1 << 1) # define UDC_PULLUP_EN (1 << 0) -#define UDC_SYSCON2_REG UDC_REG(0x1C) /* System config 2 */ +#define UDC_SYSCON2 (UDC_BASE + 0x1C) /* System config 2 */ # define UDC_RMT_WKP (1 << 6) # define UDC_STALL_CMD (1 << 5) # define UDC_DEV_CFG (1 << 3) # define UDC_CLR_CFG (1 << 2) -#define UDC_DEVSTAT_REG UDC_REG(0x20) /* Device status */ +#define UDC_DEVSTAT (UDC_BASE + 0x20) /* Device status */ # define UDC_B_HNP_ENABLE (1 << 9) # define UDC_A_HNP_SUPPORT (1 << 8) # define UDC_A_ALT_HNP_SUPPORT (1 << 7) @@ -64,26 +63,26 @@ # define UDC_ADD (1 << 2) # define UDC_DEF (1 << 1) # define UDC_ATT (1 << 0) -#define UDC_SOF_REG UDC_REG(0x24) /* Start of frame */ +#define UDC_SOF (UDC_BASE + 0x24) /* Start of frame */ # define UDC_FT_LOCK (1 << 12) # define UDC_TS_OK (1 << 11) # define UDC_TS 0x03ff -#define UDC_IRQ_EN_REG UDC_REG(0x28) /* Interrupt enable */ +#define UDC_IRQ_EN (UDC_BASE + 0x28) /* Interrupt enable */ # define UDC_SOF_IE (1 << 7) # define UDC_EPN_RX_IE (1 << 5) # define UDC_EPN_TX_IE (1 << 4) # define UDC_DS_CHG_IE (1 << 3) # define UDC_EP0_IE (1 << 0) -#define UDC_DMA_IRQ_EN_REG UDC_REG(0x2C) /* DMA irq enable */ +#define UDC_DMA_IRQ_EN (UDC_BASE + 0x2C) /* DMA irq enable */ /* rx/tx dma channels numbered 1-3 not 0-2 */ # define UDC_TX_DONE_IE(n) (1 << (4 * (n) - 2)) # define UDC_RX_CNT_IE(n) (1 << (4 * (n) - 3)) # define UDC_RX_EOT_IE(n) (1 << (4 * (n) - 4)) -#define UDC_IRQ_SRC_REG UDC_REG(0x30) /* Interrupt source */ +#define UDC_IRQ_SRC (UDC_BASE + 0x30) /* Interrupt source */ # define UDC_TXN_DONE (1 << 10) # define UDC_RXN_CNT (1 << 9) # define UDC_RXN_EOT (1 << 8) -# define UDC_SOF (1 << 7) +# define UDC_IRQ_SOF (1 << 7) # define UDC_EPN_RX (1 << 5) # define UDC_EPN_TX (1 << 4) # define UDC_DS_CHG (1 << 3) @@ -91,41 +90,41 @@ # define UDC_EP0_RX (1 << 1) # define UDC_EP0_TX (1 << 0) # define UDC_IRQ_SRC_MASK 0x7bf -#define UDC_EPN_STAT_REG UDC_REG(0x34) /* EP irq status */ -#define UDC_DMAN_STAT_REG UDC_REG(0x38) /* DMA irq status */ +#define UDC_EPN_STAT (UDC_BASE + 0x34) /* EP irq status */ +#define UDC_DMAN_STAT (UDC_BASE + 0x38) /* DMA irq status */ # define UDC_DMA_RX_SB (1 << 12) # define UDC_DMA_RX_SRC(x) (((x)>>8) & 0xf) # define UDC_DMA_TX_SRC(x) (((x)>>0) & 0xf) /* DMA configuration registers: up to three channels in each direction. */ -#define UDC_RXDMA_CFG_REG UDC_REG(0x40) /* 3 eps for RX DMA */ +#define UDC_RXDMA_CFG (UDC_BASE + 0x40) /* 3 eps for RX DMA */ # define UDC_DMA_REQ (1 << 12) -#define UDC_TXDMA_CFG_REG UDC_REG(0x44) /* 3 eps for TX DMA */ -#define UDC_DATA_DMA_REG UDC_REG(0x48) /* rx/tx fifo addr */ +#define UDC_TXDMA_CFG (UDC_BASE + 0x44) /* 3 eps for TX DMA */ +#define UDC_DATA_DMA (UDC_BASE + 0x48) /* rx/tx fifo addr */ /* rx/tx dma control, numbering channels 1-3 not 0-2 */ -#define UDC_TXDMA_REG(chan) UDC_REG(0x50 - 4 + 4 * (chan)) +#define UDC_TXDMA(chan) (UDC_BASE + 0x50 - 4 + 4 * (chan)) # define UDC_TXN_EOT (1 << 15) /* bytes vs packets */ # define UDC_TXN_START (1 << 14) /* start transfer */ # define UDC_TXN_TSC 0x03ff /* units in xfer */ -#define UDC_RXDMA_REG(chan) UDC_REG(0x60 - 4 + 4 * (chan)) +#define UDC_RXDMA(chan) (UDC_BASE + 0x60 - 4 + 4 * (chan)) # define UDC_RXN_STOP (1 << 15) /* enable EOT irq */ # define UDC_RXN_TC 0x00ff /* packets in xfer */ /* * Endpoint configuration registers (used before CFG_LOCK is set) - * UDC_EP_TX_REG(0) is unused + * UDC_EP_TX(0) is unused */ -#define UDC_EP_RX_REG(endpoint) UDC_REG(0x80 + (endpoint)*4) +#define UDC_EP_RX(endpoint) (UDC_BASE + 0x80 + (endpoint)*4) # define UDC_EPN_RX_VALID (1 << 15) # define UDC_EPN_RX_DB (1 << 14) /* buffer size in bits 13, 12 */ # define UDC_EPN_RX_ISO (1 << 11) /* buffer pointer in low 11 bits */ -#define UDC_EP_TX_REG(endpoint) UDC_REG(0xc0 + (endpoint)*4) - /* same bitfields as in RX_REG */ +#define UDC_EP_TX(endpoint) (UDC_BASE + 0xc0 + (endpoint)*4) + /* same bitfields as in RX */ /*-------------------------------------------------------------------------*/ @@ -195,14 +194,14 @@ struct omap_udc { /*-------------------------------------------------------------------------*/ -#define MOD_CONF_CTRL_0_REG __REG32(MOD_CONF_CTRL_0) -#define VBUS_W2FC_1510 (1 << 17) /* 0 gpio0, 1 dvdd2 pin */ +/* MOD_CONF_CTRL_0 */ +#define VBUS_W2FC_1510 (1 << 17) /* 0 gpio0, 1 dvdd2 pin */ -#define FUNC_MUX_CTRL_0_REG __REG32(FUNC_MUX_CTRL_0) +/* FUNC_MUX_CTRL_0 */ #define VBUS_CTRL_1510 (1 << 19) /* 1 connected (software) */ #define VBUS_MODE_1510 (1 << 18) /* 0 hardware, 1 software */ -#define HMC_1510 ((MOD_CONF_CTRL_0_REG >> 1) & 0x3f) -#define HMC_1610 (OTG_SYSCON_2_REG & 0x3f) +#define HMC_1510 ((omap_readl(MOD_CONF_CTRL_0) >> 1) & 0x3f) +#define HMC_1610 (omap_readl(OTG_SYSCON_2) & 0x3f) #define HMC (cpu_is_omap15xx() ? HMC_1510 : HMC_1610) -- cgit v1.2.3 From 7a8576204333d133d58cbcc59dacf49a5546e3e4 Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Sun, 22 Jun 2008 23:36:39 +0100 Subject: [ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers The pxa2xx_udc.c driver is renamed to pxa25x_udc.c (the platform driver name changes from pxa2xx-udc to pxa25x-udc) and the platform driver name of pxa27x_udc.c is fixed to pxa27x-udc. pxa_device_udc in devices.c is split into pxa25x and pxa27x flavors and the pxa27x_device_udc is enabled in pxa27x.c. Signed-off-by: Philipp Zabel Acked-by: Nicolas Pitre Acked-by: Eric Miao Signed-off-by: Russell King Including from Ian Molton: Fixes for mistakes left over from the PXA2{5,7}X UDC split. Signed-off-by: Ian Molton Signed-off-by: Russell King --- drivers/usb/gadget/Kconfig | 12 +- drivers/usb/gadget/Makefile | 2 +- drivers/usb/gadget/ether.c | 2 +- drivers/usb/gadget/gadget_chips.h | 4 +- drivers/usb/gadget/inode.c | 2 +- drivers/usb/gadget/pxa25x_udc.c | 2388 ++++++++++++++++++++++++++++++++++++ drivers/usb/gadget/pxa25x_udc.h | 266 +++++ drivers/usb/gadget/pxa27x_udc.c | 4 +- drivers/usb/gadget/pxa2xx_udc.c | 2389 ------------------------------------- drivers/usb/gadget/pxa2xx_udc.h | 267 ----- 10 files changed, 2667 insertions(+), 2669 deletions(-) create mode 100644 drivers/usb/gadget/pxa25x_udc.c create mode 100644 drivers/usb/gadget/pxa25x_udc.h delete mode 100644 drivers/usb/gadget/pxa2xx_udc.c delete mode 100644 drivers/usb/gadget/pxa2xx_udc.h (limited to 'drivers/usb/gadget') diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig index 6e784d2db42..13dcec30457 100644 --- a/drivers/usb/gadget/Kconfig +++ b/drivers/usb/gadget/Kconfig @@ -172,7 +172,7 @@ config USB_NET2280 default USB_GADGET select USB_GADGET_SELECTED -config USB_GADGET_PXA2XX +config USB_GADGET_PXA25X boolean "PXA 25x or IXP 4xx" depends on (ARCH_PXA && PXA25x) || ARCH_IXP4XX help @@ -184,19 +184,19 @@ config USB_GADGET_PXA2XX zero (for control transfers). Say "y" to link the driver statically, or "m" to build a - dynamically linked module called "pxa2xx_udc" and force all + dynamically linked module called "pxa25x_udc" and force all gadget drivers to also be dynamically linked. -config USB_PXA2XX +config USB_PXA25X tristate - depends on USB_GADGET_PXA2XX + depends on USB_GADGET_PXA25X default USB_GADGET select USB_GADGET_SELECTED # if there's only one gadget driver, using only two bulk endpoints, # don't waste memory for the other endpoints -config USB_PXA2XX_SMALL - depends on USB_GADGET_PXA2XX +config USB_PXA25X_SMALL + depends on USB_GADGET_PXA25X bool default n if USB_ETH_RNDIS default y if USB_ZERO diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile index 12357255d74..e258afd25fa 100644 --- a/drivers/usb/gadget/Makefile +++ b/drivers/usb/gadget/Makefile @@ -8,7 +8,7 @@ endif obj-$(CONFIG_USB_DUMMY_HCD) += dummy_hcd.o obj-$(CONFIG_USB_NET2280) += net2280.o obj-$(CONFIG_USB_AMD5536UDC) += amd5536udc.o -obj-$(CONFIG_USB_PXA2XX) += pxa2xx_udc.o +obj-$(CONFIG_USB_PXA25X) += pxa25x_udc.o obj-$(CONFIG_USB_PXA27X) += pxa27x_udc.o obj-$(CONFIG_USB_GOKU) += goku_udc.o obj-$(CONFIG_USB_OMAP) += omap_udc.o diff --git a/drivers/usb/gadget/ether.c b/drivers/usb/gadget/ether.c index 8d61ea67a81..4ce3950b997 100644 --- a/drivers/usb/gadget/ether.c +++ b/drivers/usb/gadget/ether.c @@ -262,7 +262,7 @@ MODULE_PARM_DESC(host_addr, "Host Ethernet Address"); /* For CDC-incapable hardware, choose the simple cdc subset. * Anything that talks bulk (without notable bugs) can do this. */ -#ifdef CONFIG_USB_GADGET_PXA2XX +#ifdef CONFIG_USB_GADGET_PXA25X #define DEV_CONFIG_SUBSET #endif diff --git a/drivers/usb/gadget/gadget_chips.h b/drivers/usb/gadget/gadget_chips.h index f7f159c1002..ca5149ea731 100644 --- a/drivers/usb/gadget/gadget_chips.h +++ b/drivers/usb/gadget/gadget_chips.h @@ -29,8 +29,8 @@ #define gadget_is_dummy(g) 0 #endif -#ifdef CONFIG_USB_GADGET_PXA2XX -#define gadget_is_pxa(g) !strcmp("pxa2xx_udc", (g)->name) +#ifdef CONFIG_USB_GADGET_PXA25X +#define gadget_is_pxa(g) !strcmp("pxa25x_udc", (g)->name) #else #define gadget_is_pxa(g) 0 #endif diff --git a/drivers/usb/gadget/inode.c b/drivers/usb/gadget/inode.c index 69b0a2754f2..f132a9219e1 100644 --- a/drivers/usb/gadget/inode.c +++ b/drivers/usb/gadget/inode.c @@ -1501,7 +1501,7 @@ gadgetfs_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl) } break; -#ifndef CONFIG_USB_GADGET_PXA2XX +#ifndef CONFIG_USB_GADGET_PXA25X /* PXA automagically handles this request too */ case USB_REQ_GET_CONFIGURATION: if (ctrl->bRequestType != 0x80) diff --git a/drivers/usb/gadget/pxa25x_udc.c b/drivers/usb/gadget/pxa25x_udc.c new file mode 100644 index 00000000000..031dceb9302 --- /dev/null +++ b/drivers/usb/gadget/pxa25x_udc.c @@ -0,0 +1,2388 @@ +/* + * Intel PXA25x and IXP4xx on-chip full speed USB device controllers + * + * Copyright (C) 2002 Intrinsyc, Inc. (Frank Becker) + * Copyright (C) 2003 Robert Schwebel, Pengutronix + * Copyright (C) 2003 Benedikt Spranger, Pengutronix + * Copyright (C) 2003 David Brownell + * Copyright (C) 2003 Joshua Wise + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +/* #define VERBOSE_DEBUG */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include + +#include +#include + +/* + * This driver is PXA25x only. Grab the right register definitions. + */ +#ifdef CONFIG_ARCH_PXA +#include +#endif + +#include + + +/* + * This driver handles the USB Device Controller (UDC) in Intel's PXA 25x + * series processors. The UDC for the IXP 4xx series is very similar. + * There are fifteen endpoints, in addition to ep0. + * + * Such controller drivers work with a gadget driver. The gadget driver + * returns descriptors, implements configuration and data protocols used + * by the host to interact with this device, and allocates endpoints to + * the different protocol interfaces. The controller driver virtualizes + * usb hardware so that the gadget drivers will be more portable. + * + * This UDC hardware wants to implement a bit too much USB protocol, so + * it constrains the sorts of USB configuration change events that work. + * The errata for these chips are misleading; some "fixed" bugs from + * pxa250 a0/a1 b0/b1/b2 sure act like they're still there. + * + * Note that the UDC hardware supports DMA (except on IXP) but that's + * not used here. IN-DMA (to host) is simple enough, when the data is + * suitably aligned (16 bytes) ... the network stack doesn't do that, + * other software can. OUT-DMA is buggy in most chip versions, as well + * as poorly designed (data toggle not automatic). So this driver won't + * bother using DMA. (Mostly-working IN-DMA support was available in + * kernels before 2.6.23, but was never enabled or well tested.) + */ + +#define DRIVER_VERSION "30-June-2007" +#define DRIVER_DESC "PXA 25x USB Device Controller driver" + + +static const char driver_name [] = "pxa25x_udc"; + +static const char ep0name [] = "ep0"; + + +#ifdef CONFIG_ARCH_IXP4XX + +/* cpu-specific register addresses are compiled in to this code */ +#ifdef CONFIG_ARCH_PXA +#error "Can't configure both IXP and PXA" +#endif + +/* IXP doesn't yet support */ +#define clk_get(dev,name) NULL +#define clk_enable(clk) do { } while (0) +#define clk_disable(clk) do { } while (0) +#define clk_put(clk) do { } while (0) + +#endif + +#include "pxa25x_udc.h" + + +#ifdef CONFIG_USB_PXA25X_SMALL +#define SIZE_STR " (small)" +#else +#define SIZE_STR "" +#endif + +/* --------------------------------------------------------------------------- + * endpoint related parts of the api to the usb controller hardware, + * used by gadget driver; and the inner talker-to-hardware core. + * --------------------------------------------------------------------------- + */ + +static void pxa25x_ep_fifo_flush (struct usb_ep *ep); +static void nuke (struct pxa25x_ep *, int status); + +/* one GPIO should be used to detect VBUS from the host */ +static int is_vbus_present(void) +{ + struct pxa2xx_udc_mach_info *mach = the_controller->mach; + + if (mach->gpio_vbus) { + int value = gpio_get_value(mach->gpio_vbus); + return mach->gpio_vbus_inverted ? !value : value; + } + if (mach->udc_is_connected) + return mach->udc_is_connected(); + return 1; +} + +/* one GPIO should control a D+ pullup, so host sees this device (or not) */ +static void pullup_off(void) +{ + struct pxa2xx_udc_mach_info *mach = the_controller->mach; + + if (mach->gpio_pullup) + gpio_set_value(mach->gpio_pullup, 0); + else if (mach->udc_command) + mach->udc_command(PXA2XX_UDC_CMD_DISCONNECT); +} + +static void pullup_on(void) +{ + struct pxa2xx_udc_mach_info *mach = the_controller->mach; + + if (mach->gpio_pullup) + gpio_set_value(mach->gpio_pullup, 1); + else if (mach->udc_command) + mach->udc_command(PXA2XX_UDC_CMD_CONNECT); +} + +static void pio_irq_enable(int bEndpointAddress) +{ + bEndpointAddress &= 0xf; + if (bEndpointAddress < 8) + UICR0 &= ~(1 << bEndpointAddress); + else { + bEndpointAddress -= 8; + UICR1 &= ~(1 << bEndpointAddress); + } +} + +static void pio_irq_disable(int bEndpointAddress) +{ + bEndpointAddress &= 0xf; + if (bEndpointAddress < 8) + UICR0 |= 1 << bEndpointAddress; + else { + bEndpointAddress -= 8; + UICR1 |= 1 << bEndpointAddress; + } +} + +/* The UDCCR reg contains mask and interrupt status bits, + * so using '|=' isn't safe as it may ack an interrupt. + */ +#define UDCCR_MASK_BITS (UDCCR_REM | UDCCR_SRM | UDCCR_UDE) + +static inline void udc_set_mask_UDCCR(int mask) +{ + UDCCR = (UDCCR & UDCCR_MASK_BITS) | (mask & UDCCR_MASK_BITS); +} + +static inline void udc_clear_mask_UDCCR(int mask) +{ + UDCCR = (UDCCR & UDCCR_MASK_BITS) & ~(mask & UDCCR_MASK_BITS); +} + +static inline void udc_ack_int_UDCCR(int mask) +{ + /* udccr contains the bits we dont want to change */ + __u32 udccr = UDCCR & UDCCR_MASK_BITS; + + UDCCR = udccr | (mask & ~UDCCR_MASK_BITS); +} + +/* + * endpoint enable/disable + * + * we need to verify the descriptors used to enable endpoints. since pxa25x + * endpoint configurations are fixed, and are pretty much always enabled, + * there's not a lot to manage here. + * + * because pxa25x can't selectively initialize bulk (or interrupt) endpoints, + * (resetting endpoint halt and toggle), SET_INTERFACE is unusable except + * for a single interface (with only the default altsetting) and for gadget + * drivers that don't halt endpoints (not reset by set_interface). that also + * means that if you use ISO, you must violate the USB spec rule that all + * iso endpoints must be in non-default altsettings. + */ +static int pxa25x_ep_enable (struct usb_ep *_ep, + const struct usb_endpoint_descriptor *desc) +{ + struct pxa25x_ep *ep; + struct pxa25x_udc *dev; + + ep = container_of (_ep, struct pxa25x_ep, ep); + if (!_ep || !desc || ep->desc || _ep->name == ep0name + || desc->bDescriptorType != USB_DT_ENDPOINT + || ep->bEndpointAddress != desc->bEndpointAddress + || ep->fifo_size < le16_to_cpu + (desc->wMaxPacketSize)) { + DMSG("%s, bad ep or descriptor\n", __func__); + return -EINVAL; + } + + /* xfer types must match, except that interrupt ~= bulk */ + if (ep->bmAttributes != desc->bmAttributes + && ep->bmAttributes != USB_ENDPOINT_XFER_BULK + && desc->bmAttributes != USB_ENDPOINT_XFER_INT) { + DMSG("%s, %s type mismatch\n", __func__, _ep->name); + return -EINVAL; + } + + /* hardware _could_ do smaller, but driver doesn't */ + if ((desc->bmAttributes == USB_ENDPOINT_XFER_BULK + && le16_to_cpu (desc->wMaxPacketSize) + != BULK_FIFO_SIZE) + || !desc->wMaxPacketSize) { + DMSG("%s, bad %s maxpacket\n", __func__, _ep->name); + return -ERANGE; + } + + dev = ep->dev; + if (!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN) { + DMSG("%s, bogus device state\n", __func__); + return -ESHUTDOWN; + } + + ep->desc = desc; + ep->stopped = 0; + ep->pio_irqs = 0; + ep->ep.maxpacket = le16_to_cpu (desc->wMaxPacketSize); + + /* flush fifo (mostly for OUT buffers) */ + pxa25x_ep_fifo_flush (_ep); + + /* ... reset halt state too, if we could ... */ + + DBG(DBG_VERBOSE, "enabled %s\n", _ep->name); + return 0; +} + +static int pxa25x_ep_disable (struct usb_ep *_ep) +{ + struct pxa25x_ep *ep; + unsigned long flags; + + ep = container_of (_ep, struct pxa25x_ep, ep); + if (!_ep || !ep->desc) { + DMSG("%s, %s not enabled\n", __func__, + _ep ? ep->ep.name : NULL); + return -EINVAL; + } + local_irq_save(flags); + + nuke (ep, -ESHUTDOWN); + + /* flush fifo (mostly for IN buffers) */ + pxa25x_ep_fifo_flush (_ep); + + ep->desc = NULL; + ep->stopped = 1; + + local_irq_restore(flags); + DBG(DBG_VERBOSE, "%s disabled\n", _ep->name); + return 0; +} + +/*-------------------------------------------------------------------------*/ + +/* for the pxa25x, these can just wrap kmalloc/kfree. gadget drivers + * must still pass correctly initialized endpoints, since other controller + * drivers may care about how it's currently set up (dma issues etc). + */ + +/* + * pxa25x_ep_alloc_request - allocate a request data structure + */ +static struct usb_request * +pxa25x_ep_alloc_request (struct usb_ep *_ep, gfp_t gfp_flags) +{ + struct pxa25x_request *req; + + req = kzalloc(sizeof(*req), gfp_flags); + if (!req) + return NULL; + + INIT_LIST_HEAD (&req->queue); + return &req->req; +} + + +/* + * pxa25x_ep_free_request - deallocate a request data structure + */ +static void +pxa25x_ep_free_request (struct usb_ep *_ep, struct usb_request *_req) +{ + struct pxa25x_request *req; + + req = container_of (_req, struct pxa25x_request, req); + WARN_ON (!list_empty (&req->queue)); + kfree(req); +} + +/*-------------------------------------------------------------------------*/ + +/* + * done - retire a request; caller blocked irqs + */ +static void done(struct pxa25x_ep *ep, struct pxa25x_request *req, int status) +{ + unsigned stopped = ep->stopped; + + list_del_init(&req->queue); + + if (likely (req->req.status == -EINPROGRESS)) + req->req.status = status; + else + status = req->req.status; + + if (status && status != -ESHUTDOWN) + DBG(DBG_VERBOSE, "complete %s req %p stat %d len %u/%u\n", + ep->ep.name, &req->req, status, + req->req.actual, req->req.length); + + /* don't modify queue heads during completion callback */ + ep->stopped = 1; + req->req.complete(&ep->ep, &req->req); + ep->stopped = stopped; +} + + +static inline void ep0_idle (struct pxa25x_udc *dev) +{ + dev->ep0state = EP0_IDLE; +} + +static int +write_packet(volatile u32 *uddr, struct pxa25x_request *req, unsigned max) +{ + u8 *buf; + unsigned length, count; + + buf = req->req.buf + req->req.actual; + prefetch(buf); + + /* how big will this packet be? */ + length = min(req->req.length - req->req.actual, max); + req->req.actual += length; + + count = length; + while (likely(count--)) + *uddr = *buf++; + + return length; +} + +/* + * write to an IN endpoint fifo, as many packets as possible. + * irqs will use this to write the rest later. + * caller guarantees at least one packet buffer is ready (or a zlp). + */ +static int +write_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req) +{ + unsigned max; + + max = le16_to_cpu(ep->desc->wMaxPacketSize); + do { + unsigned count; + int is_last, is_short; + + count = write_packet(ep->reg_uddr, req, max); + + /* last packet is usually short (or a zlp) */ + if (unlikely (count != max)) + is_last = is_short = 1; + else { + if (likely(req->req.length != req->req.actual) + || req->req.zero) + is_last = 0; + else + is_last = 1; + /* interrupt/iso maxpacket may not fill the fifo */ + is_short = unlikely (max < ep->fifo_size); + } + + DBG(DBG_VERY_NOISY, "wrote %s %d bytes%s%s %d left %p\n", + ep->ep.name, count, + is_last ? "/L" : "", is_short ? "/S" : "", + req->req.length - req->req.actual, req); + + /* let loose that packet. maybe try writing another one, + * double buffering might work. TSP, TPC, and TFS + * bit values are the same for all normal IN endpoints. + */ + *ep->reg_udccs = UDCCS_BI_TPC; + if (is_short) + *ep->reg_udccs = UDCCS_BI_TSP; + + /* requests complete when all IN data is in the FIFO */ + if (is_last) { + done (ep, req, 0); + if (list_empty(&ep->queue)) + pio_irq_disable (ep->bEndpointAddress); + return 1; + } + + // TODO experiment: how robust can fifo mode tweaking be? + // double buffering is off in the default fifo mode, which + // prevents TFS from being set here. + + } while (*ep->reg_udccs & UDCCS_BI_TFS); + return 0; +} + +/* caller asserts req->pending (ep0 irq status nyet cleared); starts + * ep0 data stage. these chips want very simple state transitions. + */ +static inline +void ep0start(struct pxa25x_udc *dev, u32 flags, const char *tag) +{ + UDCCS0 = flags|UDCCS0_SA|UDCCS0_OPR; + USIR0 = USIR0_IR0; + dev->req_pending = 0; + DBG(DBG_VERY_NOISY, "%s %s, %02x/%02x\n", + __func__, tag, UDCCS0, flags); +} + +static int +write_ep0_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req) +{ + unsigned count; + int is_short; + + count = write_packet(&UDDR0, req, EP0_FIFO_SIZE); + ep->dev->stats.write.bytes += count; + + /* last packet "must be" short (or a zlp) */ + is_short = (count != EP0_FIFO_SIZE); + + DBG(DBG_VERY_NOISY, "ep0in %d bytes %d left %p\n", count, + req->req.length - req->req.actual, req); + + if (unlikely (is_short)) { + if (ep->dev->req_pending) + ep0start(ep->dev, UDCCS0_IPR, "short IN"); + else + UDCCS0 = UDCCS0_IPR; + + count = req->req.length; + done (ep, req, 0); + ep0_idle(ep->dev); +#ifndef CONFIG_ARCH_IXP4XX +#if 1 + /* This seems to get rid of lost status irqs in some cases: + * host responds quickly, or next request involves config + * change automagic, or should have been hidden, or ... + * + * FIXME get rid of all udelays possible... + */ + if (count >= EP0_FIFO_SIZE) { + count = 100; + do { + if ((UDCCS0 & UDCCS0_OPR) != 0) { + /* clear OPR, generate ack */ + UDCCS0 = UDCCS0_OPR; + break; + } + count--; + udelay(1); + } while (count); + } +#endif +#endif + } else if (ep->dev->req_pending) + ep0start(ep->dev, 0, "IN"); + return is_short; +} + + +/* + * read_fifo - unload packet(s) from the fifo we use for usb OUT + * transfers and put them into the request. caller should have made + * sure there's at least one packet ready. + * + * returns true if the request completed because of short packet or the + * request buffer having filled (and maybe overran till end-of-packet). + */ +static int +read_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req) +{ + for (;;) { + u32 udccs; + u8 *buf; + unsigned bufferspace, count, is_short; + + /* make sure there's a packet in the FIFO. + * UDCCS_{BO,IO}_RPC are all the same bit value. + * UDCCS_{BO,IO}_RNE are all the same bit value. + */ + udccs = *ep->reg_udccs; + if (unlikely ((udccs & UDCCS_BO_RPC) == 0)) + break; + buf = req->req.buf + req->req.actual; + prefetchw(buf); + bufferspace = req->req.length - req->req.actual; + + /* read all bytes from this packet */ + if (likely (udccs & UDCCS_BO_RNE)) { + count = 1 + (0x0ff & *ep->reg_ubcr); + req->req.actual += min (count, bufferspace); + } else /* zlp */ + count = 0; + is_short = (count < ep->ep.maxpacket); + DBG(DBG_VERY_NOISY, "read %s %02x, %d bytes%s req %p %d/%d\n", + ep->ep.name, udccs, count, + is_short ? "/S" : "", + req, req->req.actual, req->req.length); + while (likely (count-- != 0)) { + u8 byte = (u8) *ep->reg_uddr; + + if (unlikely (bufferspace == 0)) { + /* this happens when the driver's buffer + * is smaller than what the host sent. + * discard the extra data. + */ + if (req->req.status != -EOVERFLOW) + DMSG("%s overflow %d\n", + ep->ep.name, count); + req->req.status = -EOVERFLOW; + } else { + *buf++ = byte; + bufferspace--; + } + } + *ep->reg_udccs = UDCCS_BO_RPC; + /* RPC/RSP/RNE could now reflect the other packet buffer */ + + /* iso is one request per packet */ + if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) { + if (udccs & UDCCS_IO_ROF) + req->req.status = -EHOSTUNREACH; + /* more like "is_done" */ + is_short = 1; + } + + /* completion */ + if (is_short || req->req.actual == req->req.length) { + done (ep, req, 0); + if (list_empty(&ep->queue)) + pio_irq_disable (ep->bEndpointAddress); + return 1; + } + + /* finished that packet. the next one may be waiting... */ + } + return 0; +} + +/* + * special ep0 version of the above. no UBCR0 or double buffering; status + * handshaking is magic. most device protocols don't need control-OUT. + * CDC vendor commands (and RNDIS), mass storage CB/CBI, and some other + * protocols do use them. + */ +static int +read_ep0_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req) +{ + u8 *buf, byte; + unsigned bufferspace; + + buf = req->req.buf + req->req.actual; + bufferspace = req->req.length - req->req.actual; + + while (UDCCS0 & UDCCS0_RNE) { + byte = (u8) UDDR0; + + if (unlikely (bufferspace == 0)) { + /* this happens when the driver's buffer + * is smaller than what the host sent. + * discard the extra data. + */ + if (req->req.status != -EOVERFLOW) + DMSG("%s overflow\n", ep->ep.name); + req->req.status = -EOVERFLOW; + } else { + *buf++ = byte; + req->req.actual++; + bufferspace--; + } + } + + UDCCS0 = UDCCS0_OPR | UDCCS0_IPR; + + /* completion */ + if (req->req.actual >= req->req.length) + return 1; + + /* finished that packet. the next one may be waiting... */ + return 0; +} + +/*-------------------------------------------------------------------------*/ + +static int +pxa25x_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) +{ + struct pxa25x_request *req; + struct pxa25x_ep *ep; + struct pxa25x_udc *dev; + unsigned long flags; + + req = container_of(_req, struct pxa25x_request, req); + if (unlikely (!_req || !_req->complete || !_req->buf + || !list_empty(&req->queue))) { + DMSG("%s, bad params\n", __func__); + return -EINVAL; + } + + ep = container_of(_ep, struct pxa25x_ep, ep); + if (unlikely (!_ep || (!ep->desc && ep->ep.name != ep0name))) { + DMSG("%s, bad ep\n", __func__); + return -EINVAL; + } + + dev = ep->dev; + if (unlikely (!dev->driver + || dev->gadget.speed == USB_SPEED_UNKNOWN)) { + DMSG("%s, bogus device state\n", __func__); + return -ESHUTDOWN; + } + + /* iso is always one packet per request, that's the only way + * we can report per-packet status. that also helps with dma. + */ + if (unlikely (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC + && req->req.length > le16_to_cpu + (ep->desc->wMaxPacketSize))) + return -EMSGSIZE; + + DBG(DBG_NOISY, "%s queue req %p, len %d buf %p\n", + _ep->name, _req, _req->length, _req->buf); + + local_irq_save(flags); + + _req->status = -EINPROGRESS; + _req->actual = 0; + + /* kickstart this i/o queue? */ + if (list_empty(&ep->queue) && !ep->stopped) { + if (ep->desc == NULL/* ep0 */) { + unsigned length = _req->length; + + switch (dev->ep0state) { + case EP0_IN_DATA_PHASE: + dev->stats.write.ops++; + if (write_ep0_fifo(ep, req)) + req = NULL; + break; + + case EP0_OUT_DATA_PHASE: + dev->stats.read.ops++; + /* messy ... */ + if (dev->req_config) { + DBG(DBG_VERBOSE, "ep0 config ack%s\n", + dev->has_cfr ? "" : " raced"); + if (dev->has_cfr) + UDCCFR = UDCCFR_AREN|UDCCFR_ACM + |UDCCFR_MB1; + done(ep, req, 0); + dev->ep0state = EP0_END_XFER; + local_irq_restore (flags); + return 0; + } + if (dev->req_pending) + ep0start(dev, UDCCS0_IPR, "OUT"); + if (length == 0 || ((UDCCS0 & UDCCS0_RNE) != 0 + && read_ep0_fifo(ep, req))) { + ep0_idle(dev); + done(ep, req, 0); + req = NULL; + } + break; + + default: + DMSG("ep0 i/o, odd state %d\n", dev->ep0state); + local_irq_restore (flags); + return -EL2HLT; + } + /* can the FIFO can satisfy the request immediately? */ + } else if ((ep->bEndpointAddress & USB_DIR_IN) != 0) { + if ((*ep->reg_udccs & UDCCS_BI_TFS) != 0 + && write_fifo(ep, req)) + req = NULL; + } else if ((*ep->reg_udccs & UDCCS_BO_RFS) != 0 + && read_fifo(ep, req)) { + req = NULL; + } + + if (likely (req && ep->desc)) + pio_irq_enable(ep->bEndpointAddress); + } + + /* pio or dma irq handler advances the queue. */ + if (likely(req != NULL)) + list_add_tail(&req->queue, &ep->queue); + local_irq_restore(flags); + + return 0; +} + + +/* + * nuke - dequeue ALL requests + */ +static void nuke(struct pxa25x_ep *ep, int status) +{ + struct pxa25x_request *req; + + /* called with irqs blocked */ + while (!list_empty(&ep->queue)) { + req = list_entry(ep->queue.next, + struct pxa25x_request, + queue); + done(ep, req, status); + } + if (ep->desc) + pio_irq_disable (ep->bEndpointAddress); +} + + +/* dequeue JUST ONE request */ +static int pxa25x_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) +{ + struct pxa25x_ep *ep; + struct pxa25x_request *req; + unsigned long flags; + + ep = container_of(_ep, struct pxa25x_ep, ep); + if (!_ep || ep->ep.name == ep0name) + return -EINVAL; + + local_irq_save(flags); + + /* make sure it's actually queued on this endpoint */ + list_for_each_entry (req, &ep->queue, queue) { + if (&req->req == _req) + break; + } + if (&req->req != _req) { + local_irq_restore(flags); + return -EINVAL; + } + + done(ep, req, -ECONNRESET); + + local_irq_restore(flags); + return 0; +} + +/*-------------------------------------------------------------------------*/ + +static int pxa25x_ep_set_halt(struct usb_ep *_ep, int value) +{ + struct pxa25x_ep *ep; + unsigned long flags; + + ep = container_of(_ep, struct pxa25x_ep, ep); + if (unlikely (!_ep + || (!ep->desc && ep->ep.name != ep0name)) + || ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) { + DMSG("%s, bad ep\n", __func__); + return -EINVAL; + } + if (value == 0) { + /* this path (reset toggle+halt) is needed to implement + * SET_INTERFACE on normal hardware. but it can't be + * done from software on the PXA UDC, and the hardware + * forgets to do it as part of SET_INTERFACE automagic. + */ + DMSG("only host can clear %s halt\n", _ep->name); + return -EROFS; + } + + local_irq_save(flags); + + if ((ep->bEndpointAddress & USB_DIR_IN) != 0 + && ((*ep->reg_udccs & UDCCS_BI_TFS) == 0 + || !list_empty(&ep->queue))) { + local_irq_restore(flags); + return -EAGAIN; + } + + /* FST bit is the same for control, bulk in, bulk out, interrupt in */ + *ep->reg_udccs = UDCCS_BI_FST|UDCCS_BI_FTF; + + /* ep0 needs special care */ + if (!ep->desc) { + start_watchdog(ep->dev); + ep->dev->req_pending = 0; + ep->dev->ep0state = EP0_STALL; + + /* and bulk/intr endpoints like dropping stalls too */ + } else { + unsigned i; + for (i = 0; i < 1000; i += 20) { + if (*ep->reg_udccs & UDCCS_BI_SST) + break; + udelay(20); + } + } + local_irq_restore(flags); + + DBG(DBG_VERBOSE, "%s halt\n", _ep->name); + return 0; +} + +static int pxa25x_ep_fifo_status(struct usb_ep *_ep) +{ + struct pxa25x_ep *ep; + + ep = container_of(_ep, struct pxa25x_ep, ep); + if (!_ep) { + DMSG("%s, bad ep\n", __func__); + return -ENODEV; + } + /* pxa can't report unclaimed bytes from IN fifos */ + if ((ep->bEndpointAddress & USB_DIR_IN) != 0) + return -EOPNOTSUPP; + if (ep->dev->gadget.speed == USB_SPEED_UNKNOWN + || (*ep->reg_udccs & UDCCS_BO_RFS) == 0) + return 0; + else + return (*ep->reg_ubcr & 0xfff) + 1; +} + +static void pxa25x_ep_fifo_flush(struct usb_ep *_ep) +{ + struct pxa25x_ep *ep; + + ep = container_of(_ep, struct pxa25x_ep, ep); + if (!_ep || ep->ep.name == ep0name || !list_empty(&ep->queue)) { + DMSG("%s, bad ep\n", __func__); + return; + } + + /* toggle and halt bits stay unchanged */ + + /* for OUT, just read and discard the FIFO contents. */ + if ((ep->bEndpointAddress & USB_DIR_IN) == 0) { + while (((*ep->reg_udccs) & UDCCS_BO_RNE) != 0) + (void) *ep->reg_uddr; + return; + } + + /* most IN status is the same, but ISO can't stall */ + *ep->reg_udccs = UDCCS_BI_TPC|UDCCS_BI_FTF|UDCCS_BI_TUR + | (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) + ? 0 : UDCCS_BI_SST; +} + + +static struct usb_ep_ops pxa25x_ep_ops = { + .enable = pxa25x_ep_enable, + .disable = pxa25x_ep_disable, + + .alloc_request = pxa25x_ep_alloc_request, + .free_request = pxa25x_ep_free_request, + + .queue = pxa25x_ep_queue, + .dequeue = pxa25x_ep_dequeue, + + .set_halt = pxa25x_ep_set_halt, + .fifo_status = pxa25x_ep_fifo_status, + .fifo_flush = pxa25x_ep_fifo_flush, +}; + + +/* --------------------------------------------------------------------------- + * device-scoped parts of the api to the usb controller hardware + * --------------------------------------------------------------------------- + */ + +static int pxa25x_udc_get_frame(struct usb_gadget *_gadget) +{ + return ((UFNRH & 0x07) << 8) | (UFNRL & 0xff); +} + +static int pxa25x_udc_wakeup(struct usb_gadget *_gadget) +{ + /* host may not have enabled remote wakeup */ + if ((UDCCS0 & UDCCS0_DRWF) == 0) + return -EHOSTUNREACH; + udc_set_mask_UDCCR(UDCCR_RSM); + return 0; +} + +static void stop_activity(struct pxa25x_udc *, struct usb_gadget_driver *); +static void udc_enable (struct pxa25x_udc *); +static void udc_disable(struct pxa25x_udc *); + +/* We disable the UDC -- and its 48 MHz clock -- whenever it's not + * in active use. + */ +static int pullup(struct pxa25x_udc *udc) +{ + int is_active = udc->vbus && udc->pullup && !udc->suspended; + DMSG("%s\n", is_active ? "active" : "inactive"); + if (is_active) { + if (!udc->active) { + udc->active = 1; + /* Enable clock for USB device */ + clk_enable(udc->clk); + udc_enable(udc); + } + } else { + if (udc->active) { + if (udc->gadget.speed != USB_SPEED_UNKNOWN) { + DMSG("disconnect %s\n", udc->driver + ? udc->driver->driver.name + : "(no driver)"); + stop_activity(udc, udc->driver); + } + udc_disable(udc); + /* Disable clock for USB device */ + clk_disable(udc->clk); + udc->active = 0; + } + + } + return 0; +} + +/* VBUS reporting logically comes from a transceiver */ +static int pxa25x_udc_vbus_session(struct usb_gadget *_gadget, int is_active) +{ + struct pxa25x_udc *udc; + + udc = container_of(_gadget, struct pxa25x_udc, gadget); + udc->vbus = (is_active != 0); + DMSG("vbus %s\n", is_active ? "supplied" : "inactive"); + pullup(udc); + return 0; +} + +/* drivers may have software control over D+ pullup */ +static int pxa25x_udc_pullup(struct usb_gadget *_gadget, int is_active) +{ + struct pxa25x_udc *udc; + + udc = container_of(_gadget, struct pxa25x_udc, gadget); + + /* not all boards support pullup control */ + if (!udc->mach->gpio_pullup && !udc->mach->udc_command) + return -EOPNOTSUPP; + + udc->pullup = (is_active != 0); + pullup(udc); + return 0; +} + +static const struct usb_gadget_ops pxa25x_udc_ops = { + .get_frame = pxa25x_udc_get_frame, + .wakeup = pxa25x_udc_wakeup, + .vbus_session = pxa25x_udc_vbus_session, + .pullup = pxa25x_udc_pullup, + + // .vbus_draw ... boards may consume current from VBUS, up to + // 100-500mA based on config. the 500uA suspend ceiling means + // that exclusively vbus-powered PXA designs violate USB specs. +}; + +/*-------------------------------------------------------------------------*/ + +#ifdef CONFIG_USB_GADGET_DEBUG_FS + +static int +udc_seq_show(struct seq_file *m, void *_d) +{ + struct pxa25x_udc *dev = m->private; + unsigned long flags; + int i; + u32 tmp; + + local_irq_save(flags); + + /* basic device status */ + seq_printf(m, DRIVER_DESC "\n" + "%s version: %s\nGadget driver: %s\nHost %s\n\n", + driver_name, DRIVER_VERSION SIZE_STR "(pio)", + dev->driver ? dev->driver->driver.name : "(none)", + is_vbus_present() ? "full speed" : "disconnected"); + + /* registers for device and ep0 */ + seq_printf(m, + "uicr %02X.%02X, usir %02X.%02x, ufnr %02X.%02X\n", + UICR1, UICR0, USIR1, USIR0, UFNRH, UFNRL); + + tmp = UDCCR; + seq_printf(m, + "udccr %02X =%s%s%s%s%s%s%s%s\n", tmp, + (tmp & UDCCR_REM) ? " rem" : "", + (tmp & UDCCR_RSTIR) ? " rstir" : "", + (tmp & UDCCR_SRM) ? " srm" : "", + (tmp & UDCCR_SUSIR) ? " susir" : "", + (tmp & UDCCR_RESIR) ? " resir" : "", + (tmp & UDCCR_RSM) ? " rsm" : "", + (tmp & UDCCR_UDA) ? " uda" : "", + (tmp & UDCCR_UDE) ? " ude" : ""); + + tmp = UDCCS0; + seq_printf(m, + "udccs0 %02X =%s%s%s%s%s%s%s%s\n", tmp, + (tmp & UDCCS0_SA) ? " sa" : "", + (tmp & UDCCS0_RNE) ? " rne" : "", + (tmp & UDCCS0_FST) ? " fst" : "", + (tmp & UDCCS0_SST) ? " sst" : "", + (tmp & UDCCS0_DRWF) ? " dwrf" : "", + (tmp & UDCCS0_FTF) ? " ftf" : "", + (tmp & UDCCS0_IPR) ? " ipr" : "", + (tmp & UDCCS0_OPR) ? " opr" : ""); + + if (dev->has_cfr) { + tmp = UDCCFR; + seq_printf(m, + "udccfr %02X =%s%s\n", tmp, + (tmp & UDCCFR_AREN) ? " aren" : "", + (tmp & UDCCFR_ACM) ? " acm" : ""); + } + + if (!is_vbus_present() || !dev->driver) + goto done; + + seq_printf(m, "ep0 IN %lu/%lu, OUT %lu/%lu\nirqs %lu\n\n", + dev->stats.write.bytes, dev->stats.write.ops, + dev->stats.read.bytes, dev->stats.read.ops, + dev->stats.irqs); + + /* dump endpoint queues */ + for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) { + struct pxa25x_ep *ep = &dev->ep [i]; + struct pxa25x_request *req; + + if (i != 0) { + const struct usb_endpoint_descriptor *desc; + + desc = ep->desc; + if (!desc) + continue; + tmp = *dev->ep [i].reg_udccs; + seq_printf(m, + "%s max %d %s udccs %02x irqs %lu\n", + ep->ep.name, le16_to_cpu(desc->wMaxPacketSize), + "pio", tmp, ep->pio_irqs); + /* TODO translate all five groups of udccs bits! */ + + } else /* ep0 should only have one transfer queued */ + seq_printf(m, "ep0 max 16 pio irqs %lu\n", + ep->pio_irqs); + + if (list_empty(&ep->queue)) { + seq_printf(m, "\t(nothing queued)\n"); + continue; + } + list_for_each_entry(req, &ep->queue, queue) { + seq_printf(m, + "\treq %p len %d/%d buf %p\n", + &req->req, req->req.actual, + req->req.length, req->req.buf); + } + } + +done: + local_irq_restore(flags); + return 0; +} + +static int +udc_debugfs_open(struct inode *inode, struct file *file) +{ + return single_open(file, udc_seq_show, inode->i_private); +} + +static const struct file_operations debug_fops = { + .open = udc_debugfs_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, + .owner = THIS_MODULE, +}; + +#define create_debug_files(dev) \ + do { \ + dev->debugfs_udc = debugfs_create_file(dev->gadget.name, \ + S_IRUGO, NULL, dev, &debug_fops); \ + } while (0) +#define remove_debug_files(dev) \ + do { \ + if (dev->debugfs_udc) \ + debugfs_remove(dev->debugfs_udc); \ + } while (0) + +#else /* !CONFIG_USB_GADGET_DEBUG_FILES */ + +#define create_debug_files(dev) do {} while (0) +#define remove_debug_files(dev) do {} while (0) + +#endif /* CONFIG_USB_GADGET_DEBUG_FILES */ + +/*-------------------------------------------------------------------------*/ + +/* + * udc_disable - disable USB device controller + */ +static void udc_disable(struct pxa25x_udc *dev) +{ + /* block all irqs */ + udc_set_mask_UDCCR(UDCCR_SRM|UDCCR_REM); + UICR0 = UICR1 = 0xff; + UFNRH = UFNRH_SIM; + + /* if hardware supports it, disconnect from usb */ + pullup_off(); + + udc_clear_mask_UDCCR(UDCCR_UDE); + + ep0_idle (dev); + dev->gadget.speed = USB_SPEED_UNKNOWN; +} + + +/* + * udc_reinit - initialize software state + */ +static void udc_reinit(struct pxa25x_udc *dev) +{ + u32 i; + + /* device/ep0 records init */ + INIT_LIST_HEAD (&dev->gadget.ep_list); + INIT_LIST_HEAD (&dev->gadget.ep0->ep_list); + dev->ep0state = EP0_IDLE; + + /* basic endpoint records init */ + for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) { + struct pxa25x_ep *ep = &dev->ep[i]; + + if (i != 0) + list_add_tail (&ep->ep.ep_list, &dev->gadget.ep_list); + + ep->desc = NULL; + ep->stopped = 0; + INIT_LIST_HEAD (&ep->queue); + ep->pio_irqs = 0; + } + + /* the rest was statically initialized, and is read-only */ +} + +/* until it's enabled, this UDC should be completely invisible + * to any USB host. + */ +static void udc_enable (struct pxa25x_udc *dev) +{ + udc_clear_mask_UDCCR(UDCCR_UDE); + + /* try to clear these bits before we enable the udc */ + udc_ack_int_UDCCR(UDCCR_SUSIR|/*UDCCR_RSTIR|*/UDCCR_RESIR); + + ep0_idle(dev); + dev->gadget.speed = USB_SPEED_UNKNOWN; + dev->stats.irqs = 0; + + /* + * sequence taken from chapter 12.5.10, PXA250 AppProcDevManual: + * - enable UDC + * - if RESET is already in progress, ack interrupt + * - unmask reset interrupt + */ + udc_set_mask_UDCCR(UDCCR_UDE); + if (!(UDCCR & UDCCR_UDA)) + udc_ack_int_UDCCR(UDCCR_RSTIR); + + if (dev->has_cfr /* UDC_RES2 is defined */) { + /* pxa255 (a0+) can avoid a set_config race that could + * prevent gadget drivers from configuring correctly + */ + UDCCFR = UDCCFR_ACM | UDCCFR_MB1; + } else { + /* "USB test mode" for pxa250 errata 40-42 (stepping a0, a1) + * which could result in missing packets and interrupts. + * supposedly one bit per endpoint, controlling whether it + * double buffers or not; ACM/AREN bits fit into the holes. + * zero bits (like USIR0_IRx) disable double buffering. + */ + UDC_RES1 = 0x00; + UDC_RES2 = 0x00; + } + + /* enable suspend/resume and reset irqs */ + udc_clear_mask_UDCCR(UDCCR_SRM | UDCCR_REM); + + /* enable ep0 irqs */ + UICR0 &= ~UICR0_IM0; + + /* if hardware supports it, pullup D+ and wait for reset */ + pullup_on(); +} + + +/* when a driver is successfully registered, it will receive + * control requests including set_configuration(), which enables + * non-control requests. then usb traffic follows until a + * disconnect is reported. then a host may connect again, or + * the driver might get unbound. + */ +int usb_gadget_register_driver(struct usb_gadget_driver *driver) +{ + struct pxa25x_udc *dev = the_controller; + int retval; + + if (!driver + || driver->speed < USB_SPEED_FULL + || !driver->bind + || !driver->disconnect + || !driver->setup) + return -EINVAL; + if (!dev) + return -ENODEV; + if (dev->driver) + return -EBUSY; + + /* first hook up the driver ... */ + dev->driver = driver; + dev->gadget.dev.driver = &driver->driver; + dev->pullup = 1; + + retval = device_add (&dev->gadget.dev); + if (retval) { +fail: + dev->driver = NULL; + dev->gadget.dev.driver = NULL; + return retval; + } + retval = driver->bind(&dev->gadget); + if (retval) { + DMSG("bind to driver %s --> error %d\n", + driver->driver.name, retval); + device_del (&dev->gadget.dev); + goto fail; + } + + /* ... then enable host detection and ep0; and we're ready + * for set_configuration as well as eventual disconnect. + */ + DMSG("registered gadget driver '%s'\n", driver->driver.name); + pullup(dev); + dump_state(dev); + return 0; +} +EXPORT_SYMBOL(usb_gadget_register_driver); + +static void +stop_activity(struct pxa25x_udc *dev, struct usb_gadget_driver *driver) +{ + int i; + + /* don't disconnect drivers more than once */ + if (dev->gadget.speed == USB_SPEED_UNKNOWN) + driver = NULL; + dev->gadget.speed = USB_SPEED_UNKNOWN; + + /* prevent new request submissions, kill any outstanding requests */ + for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) { + struct pxa25x_ep *ep = &dev->ep[i]; + + ep->stopped = 1; + nuke(ep, -ESHUTDOWN); + } + del_timer_sync(&dev->timer); + + /* report disconnect; the driver is already quiesced */ + if (driver) + driver->disconnect(&dev->gadget); + + /* re-init driver-visible data structures */ + udc_reinit(dev); +} + +int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) +{ + struct pxa25x_udc *dev = the_controller; + + if (!dev) + return -ENODEV; + if (!driver || driver != dev->driver || !driver->unbind) + return -EINVAL; + + local_irq_disable(); + dev->pullup = 0; + pullup(dev); + stop_activity(dev, driver); + local_irq_enable(); + + driver->unbind(&dev->gadget); + dev->gadget.dev.driver = NULL; + dev->driver = NULL; + + device_del (&dev->gadget.dev); + + DMSG("unregistered gadget driver '%s'\n", driver->driver.name); + dump_state(dev); + return 0; +} +EXPORT_SYMBOL(usb_gadget_unregister_driver); + + +/*-------------------------------------------------------------------------*/ + +#ifdef CONFIG_ARCH_LUBBOCK + +/* Lubbock has separate connect and disconnect irqs. More typical designs + * use one GPIO as the VBUS IRQ, and another to control the D+ pullup. + */ + +static irqreturn_t +lubbock_vbus_irq(int irq, void *_dev) +{ + struct pxa25x_udc *dev = _dev; + int vbus; + + dev->stats.irqs++; + switch (irq) { + case LUBBOCK_USB_IRQ: + vbus = 1; + disable_irq(LUBBOCK_USB_IRQ); + enable_irq(LUBBOCK_USB_DISC_IRQ); + break; + case LUBBOCK_USB_DISC_IRQ: + vbus = 0; + disable_irq(LUBBOCK_USB_DISC_IRQ); + enable_irq(LUBBOCK_USB_IRQ); + break; + default: + return IRQ_NONE; + } + + pxa25x_udc_vbus_session(&dev->gadget, vbus); + return IRQ_HANDLED; +} + +#endif + +static irqreturn_t udc_vbus_irq(int irq, void *_dev) +{ + struct pxa25x_udc *dev = _dev; + int vbus = gpio_get_value(dev->mach->gpio_vbus); + + if (dev->mach->gpio_vbus_inverted) + vbus = !vbus; + + pxa25x_udc_vbus_session(&dev->gadget, vbus); + return IRQ_HANDLED; +} + + +/*-------------------------------------------------------------------------*/ + +static inline void clear_ep_state (struct pxa25x_udc *dev) +{ + unsigned i; + + /* hardware SET_{CONFIGURATION,INTERFACE} automagic resets endpoint + * fifos, and pending transactions mustn't be continued in any case. + */ + for (i = 1; i < PXA_UDC_NUM_ENDPOINTS; i++) + nuke(&dev->ep[i], -ECONNABORTED); +} + +static void udc_watchdog(unsigned long _dev) +{ + struct pxa25x_udc *dev = (void *)_dev; + + local_irq_disable(); + if (dev->ep0state == EP0_STALL + && (UDCCS0 & UDCCS0_FST) == 0 + && (UDCCS0 & UDCCS0_SST) == 0) { + UDCCS0 = UDCCS0_FST|UDCCS0_FTF; + DBG(DBG_VERBOSE, "ep0 re-stall\n"); + start_watchdog(dev); + } + local_irq_enable(); +} + +static void handle_ep0 (struct pxa25x_udc *dev) +{ + u32 udccs0 = UDCCS0; + struct pxa25x_ep *ep = &dev->ep [0]; + struct pxa25x_request *req; + union { + struct usb_ctrlrequest r; + u8 raw [8]; + u32 word [2]; + } u; + + if (list_empty(&ep->queue)) + req = NULL; + else + req = list_entry(ep->queue.next, struct pxa25x_request, queue); + + /* clear stall status */ + if (udccs0 & UDCCS0_SST) { + nuke(ep, -EPIPE); + UDCCS0 = UDCCS0_SST; + del_timer(&dev->timer); + ep0_idle(dev); + } + + /* previous request unfinished? non-error iff back-to-back ... */ + if ((udccs0 & UDCCS0_SA) != 0 && dev->ep0state != EP0_IDLE) { + nuke(ep, 0); + del_timer(&dev->timer); + ep0_idle(dev); + } + + switch (dev->ep0state) { + case EP0_IDLE: + /* late-breaking status? */ + udccs0 = UDCCS0; + + /* start control request? */ + if (likely((udccs0 & (UDCCS0_OPR|UDCCS0_SA|UDCCS0_RNE)) + == (UDCCS0_OPR|UDCCS0_SA|UDCCS0_RNE))) { + int i; + + nuke (ep, -EPROTO); + + /* read SETUP packet */ + for (i = 0; i < 8; i++) { + if (unlikely(!(UDCCS0 & UDCCS0_RNE))) { +bad_setup: + DMSG("SETUP %d!\n", i); + goto stall; + } + u.raw [i] = (u8) UDDR0; + } + if (unlikely((UDCCS0 & UDCCS0_RNE) != 0)) + goto bad_setup; + +got_setup: + DBG(DBG_VERBOSE, "SETUP %02x.%02x v%04x i%04x l%04x\n", + u.r.bRequestType, u.r.bRequest, + le16_to_cpu(u.r.wValue), + le16_to_cpu(u.r.wIndex), + le16_to_cpu(u.r.wLength)); + + /* cope with automagic for some standard requests. */ + dev->req_std = (u.r.bRequestType & USB_TYPE_MASK) + == USB_TYPE_STANDARD; + dev->req_config = 0; + dev->req_pending = 1; + switch (u.r.bRequest) { + /* hardware restricts gadget drivers here! */ + case USB_REQ_SET_CONFIGURATION: + if (u.r.bRequestType == USB_RECIP_DEVICE) { + /* reflect hardware's automagic + * up to the gadget driver. + */ +config_change: + dev->req_config = 1; + clear_ep_state(dev); + /* if !has_cfr, there's no synch + * else use AREN (later) not SA|OPR + * USIR0_IR0 acts edge sensitive + */ + } + break; + /* ... and here, even more ... */ + case USB_REQ_SET_INTERFACE: + if (u.r.bRequestType == USB_RECIP_INTERFACE) { + /* udc hardware is broken by design: + * - altsetting may only be zero; + * - hw resets all interfaces' eps; + * - ep reset doesn't include halt(?). + */ + DMSG("broken set_interface (%d/%d)\n", + le16_to_cpu(u.r.wIndex), + le16_to_cpu(u.r.wValue)); + goto config_change; + } + break; + /* hardware was supposed to hide this */ + case USB_REQ_SET_ADDRESS: + if (u.r.bRequestType == USB_RECIP_DEVICE) { + ep0start(dev, 0, "address"); + return; + } + break; + } + + if (u.r.bRequestType & USB_DIR_IN) + dev->ep0state = EP0_IN_DATA_PHASE; + else + dev->ep0state = EP0_OUT_DATA_PHASE; + + i = dev->driver->setup(&dev->gadget, &u.r); + if (i < 0) { + /* hardware automagic preventing STALL... */ + if (dev->req_config) { + /* hardware sometimes neglects to tell + * tell us about config change events, + * so later ones may fail... + */ + WARN("config change %02x fail %d?\n", + u.r.bRequest, i); + return; + /* TODO experiment: if has_cfr, + * hardware didn't ACK; maybe we + * could actually STALL! + */ + } + DBG(DBG_VERBOSE, "protocol STALL, " + "%02x err %d\n", UDCCS0, i); +stall: + /* the watchdog timer helps deal with cases + * where udc seems to clear FST wrongly, and + * then NAKs instead of STALLing. + */ + ep0start(dev, UDCCS0_FST|UDCCS0_FTF, "stall"); + start_watchdog(dev); + dev->ep0state = EP0_STALL; + + /* deferred i/o == no response yet */ + } else if (dev->req_pending) { + if (likely(dev->ep0state == EP0_IN_DATA_PHASE + || dev->req_std || u.r.wLength)) + ep0start(dev, 0, "defer"); + else + ep0start(dev, UDCCS0_IPR, "defer/IPR"); + } + + /* expect at least one data or status stage irq */ + return; + + } else if (likely((udccs0 & (UDCCS0_OPR|UDCCS0_SA)) + == (UDCCS0_OPR|UDCCS0_SA))) { + unsigned i; + + /* pxa210/250 erratum 131 for B0/B1 says RNE lies. + * still observed on a pxa255 a0. + */ + DBG(DBG_VERBOSE, "e131\n"); + nuke(ep, -EPROTO); + + /* read SETUP data, but don't trust it too much */ + for (i = 0; i < 8; i++) + u.raw [i] = (u8) UDDR0; + if ((u.r.bRequestType & USB_RECIP_MASK) + > USB_RECIP_OTHER) + goto stall; + if (u.word [0] == 0 && u.word [1] == 0) + goto stall; + goto got_setup; + } else { + /* some random early IRQ: + * - we acked FST + * - IPR cleared + * - OPR got set, without SA (likely status stage) + */ + UDCCS0 = udccs0 & (UDCCS0_SA|UDCCS0_OPR); + } + break; + case EP0_IN_DATA_PHASE: /* GET_DESCRIPTOR etc */ + if (udccs0 & UDCCS0_OPR) { + UDCCS0 = UDCCS0_OPR|UDCCS0_FTF; + DBG(DBG_VERBOSE, "ep0in premature status\n"); + if (req) + done(ep, req, 0); + ep0_idle(dev); + } else /* irq was IPR clearing */ { + if (req) { + /* this IN packet might finish the request */ + (void) write_ep0_fifo(ep, req); + } /* else IN token before response was written */ + } + break; + case EP0_OUT_DATA_PHASE: /* SET_DESCRIPTOR etc */ + if (udccs0 & UDCCS0_OPR) { + if (req) { + /* this OUT packet might finish the request */ + if (read_ep0_fifo(ep, req)) + done(ep, req, 0); + /* else more OUT packets expected */ + } /* else OUT token before read was issued */ + } else /* irq was IPR clearing */ { + DBG(DBG_VERBOSE, "ep0out premature status\n"); + if (req) + done(ep, req, 0); + ep0_idle(dev); + } + break; + case EP0_END_XFER: + if (req) + done(ep, req, 0); + /* ack control-IN status (maybe in-zlp was skipped) + * also appears after some config change events. + */ + if (udccs0 & UDCCS0_OPR) + UDCCS0 = UDCCS0_OPR; + ep0_idle(dev); + break; + case EP0_STALL: + UDCCS0 = UDCCS0_FST; + break; + } + USIR0 = USIR0_IR0; +} + +static void handle_ep(struct pxa25x_ep *ep) +{ + struct pxa25x_request *req; + int is_in = ep->bEndpointAddress & USB_DIR_IN; + int completed; + u32 udccs, tmp; + + do { + completed = 0; + if (likely (!list_empty(&ep->queue))) + req = list_entry(ep->queue.next, + struct pxa25x_request, queue); + else + req = NULL; + + // TODO check FST handling + + udccs = *ep->reg_udccs; + if (unlikely(is_in)) { /* irq from TPC, SST, or (ISO) TUR */ + tmp = UDCCS_BI_TUR; + if (likely(ep->bmAttributes == USB_ENDPOINT_XFER_BULK)) + tmp |= UDCCS_BI_SST; + tmp &= udccs; + if (likely (tmp)) + *ep->reg_udccs = tmp; + if (req && likely ((udccs & UDCCS_BI_TFS) != 0)) + completed = write_fifo(ep, req); + + } else { /* irq from RPC (or for ISO, ROF) */ + if (likely(ep->bmAttributes == USB_ENDPOINT_XFER_BULK)) + tmp = UDCCS_BO_SST | UDCCS_BO_DME; + else + tmp = UDCCS_IO_ROF | UDCCS_IO_DME; + tmp &= udccs; + if (likely(tmp)) + *ep->reg_udccs = tmp; + + /* fifos can hold packets, ready for reading... */ + if (likely(req)) { + completed = read_fifo(ep, req); + } else + pio_irq_disable (ep->bEndpointAddress); + } + ep->pio_irqs++; + } while (completed); +} + +/* + * pxa25x_udc_irq - interrupt handler + * + * avoid delays in ep0 processing. the control handshaking isn't always + * under software control (pxa250c0 and the pxa255 are better), and delays + * could cause usb protocol errors. + */ +static irqreturn_t +pxa25x_udc_irq(int irq, void *_dev) +{ + struct pxa25x_udc *dev = _dev; + int handled; + + dev->stats.irqs++; + do { + u32 udccr = UDCCR; + + handled = 0; + + /* SUSpend Interrupt Request */ + if (unlikely(udccr & UDCCR_SUSIR)) { + udc_ack_int_UDCCR(UDCCR_SUSIR); + handled = 1; + DBG(DBG_VERBOSE, "USB suspend%s\n", is_vbus_present() + ? "" : "+disconnect"); + + if (!is_vbus_present()) + stop_activity(dev, dev->driver); + else if (dev->gadget.speed != USB_SPEED_UNKNOWN + && dev->driver + && dev->driver->suspend) + dev->driver->suspend(&dev->gadget); + ep0_idle (dev); + } + + /* RESume Interrupt Request */ + if (unlikely(udccr & UDCCR_RESIR)) { + udc_ack_int_UDCCR(UDCCR_RESIR); + handled = 1; + DBG(DBG_VERBOSE, "USB resume\n"); + + if (dev->gadget.speed != USB_SPEED_UNKNOWN + && dev->driver + && dev->driver->resume + && is_vbus_present()) + dev->driver->resume(&dev->gadget); + } + + /* ReSeT Interrupt Request - USB reset */ + if (unlikely(udccr & UDCCR_RSTIR)) { + udc_ack_int_UDCCR(UDCCR_RSTIR); + handled = 1; + + if ((UDCCR & UDCCR_UDA) == 0) { + DBG(DBG_VERBOSE, "USB reset start\n"); + + /* reset driver and endpoints, + * in case that's not yet done + */ + stop_activity (dev, dev->driver); + + } else { + DBG(DBG_VERBOSE, "USB reset end\n"); + dev->gadget.speed = USB_SPEED_FULL; + memset(&dev->stats, 0, sizeof dev->stats); + /* driver and endpoints are still reset */ + } + + } else { + u32 usir0 = USIR0 & ~UICR0; + u32 usir1 = USIR1 & ~UICR1; + int i; + + if (unlikely (!usir0 && !usir1)) + continue; + + DBG(DBG_VERY_NOISY, "irq %02x.%02x\n", usir1, usir0); + + /* control traffic */ + if (usir0 & USIR0_IR0) { + dev->ep[0].pio_irqs++; + handle_ep0(dev); + handled = 1; + } + + /* endpoint data transfers */ + for (i = 0; i < 8; i++) { + u32 tmp = 1 << i; + + if (i && (usir0 & tmp)) { + handle_ep(&dev->ep[i]); + USIR0 |= tmp; + handled = 1; + } + if (usir1 & tmp) { + handle_ep(&dev->ep[i+8]); + USIR1 |= tmp; + handled = 1; + } + } + } + + /* we could also ask for 1 msec SOF (SIR) interrupts */ + + } while (handled); + return IRQ_HANDLED; +} + +/*-------------------------------------------------------------------------*/ + +static void nop_release (struct device *dev) +{ + DMSG("%s %s\n", __func__, dev->bus_id); +} + +/* this uses load-time allocation and initialization (instead of + * doing it at run-time) to save code, eliminate fault paths, and + * be more obviously correct. + */ +static struct pxa25x_udc memory = { + .gadget = { + .ops = &pxa25x_udc_ops, + .ep0 = &memory.ep[0].ep, + .name = driver_name, + .dev = { + .bus_id = "gadget", + .release = nop_release, + }, + }, + + /* control endpoint */ + .ep[0] = { + .ep = { + .name = ep0name, + .ops = &pxa25x_ep_ops, + .maxpacket = EP0_FIFO_SIZE, + }, + .dev = &memory, + .reg_udccs = &UDCCS0, + .reg_uddr = &UDDR0, + }, + + /* first group of endpoints */ + .ep[1] = { + .ep = { + .name = "ep1in-bulk", + .ops = &pxa25x_ep_ops, + .maxpacket = BULK_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = BULK_FIFO_SIZE, + .bEndpointAddress = USB_DIR_IN | 1, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .reg_udccs = &UDCCS1, + .reg_uddr = &UDDR1, + }, + .ep[2] = { + .ep = { + .name = "ep2out-bulk", + .ops = &pxa25x_ep_ops, + .maxpacket = BULK_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = BULK_FIFO_SIZE, + .bEndpointAddress = 2, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .reg_udccs = &UDCCS2, + .reg_ubcr = &UBCR2, + .reg_uddr = &UDDR2, + }, +#ifndef CONFIG_USB_PXA25X_SMALL + .ep[3] = { + .ep = { + .name = "ep3in-iso", + .ops = &pxa25x_ep_ops, + .maxpacket = ISO_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = ISO_FIFO_SIZE, + .bEndpointAddress = USB_DIR_IN | 3, + .bmAttributes = USB_ENDPOINT_XFER_ISOC, + .reg_udccs = &UDCCS3, + .reg_uddr = &UDDR3, + }, + .ep[4] = { + .ep = { + .name = "ep4out-iso", + .ops = &pxa25x_ep_ops, + .maxpacket = ISO_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = ISO_FIFO_SIZE, + .bEndpointAddress = 4, + .bmAttributes = USB_ENDPOINT_XFER_ISOC, + .reg_udccs = &UDCCS4, + .reg_ubcr = &UBCR4, + .reg_uddr = &UDDR4, + }, + .ep[5] = { + .ep = { + .name = "ep5in-int", + .ops = &pxa25x_ep_ops, + .maxpacket = INT_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = INT_FIFO_SIZE, + .bEndpointAddress = USB_DIR_IN | 5, + .bmAttributes = USB_ENDPOINT_XFER_INT, + .reg_udccs = &UDCCS5, + .reg_uddr = &UDDR5, + }, + + /* second group of endpoints */ + .ep[6] = { + .ep = { + .name = "ep6in-bulk", + .ops = &pxa25x_ep_ops, + .maxpacket = BULK_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = BULK_FIFO_SIZE, + .bEndpointAddress = USB_DIR_IN | 6, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .reg_udccs = &UDCCS6, + .reg_uddr = &UDDR6, + }, + .ep[7] = { + .ep = { + .name = "ep7out-bulk", + .ops = &pxa25x_ep_ops, + .maxpacket = BULK_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = BULK_FIFO_SIZE, + .bEndpointAddress = 7, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .reg_udccs = &UDCCS7, + .reg_ubcr = &UBCR7, + .reg_uddr = &UDDR7, + }, + .ep[8] = { + .ep = { + .name = "ep8in-iso", + .ops = &pxa25x_ep_ops, + .maxpacket = ISO_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = ISO_FIFO_SIZE, + .bEndpointAddress = USB_DIR_IN | 8, + .bmAttributes = USB_ENDPOINT_XFER_ISOC, + .reg_udccs = &UDCCS8, + .reg_uddr = &UDDR8, + }, + .ep[9] = { + .ep = { + .name = "ep9out-iso", + .ops = &pxa25x_ep_ops, + .maxpacket = ISO_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = ISO_FIFO_SIZE, + .bEndpointAddress = 9, + .bmAttributes = USB_ENDPOINT_XFER_ISOC, + .reg_udccs = &UDCCS9, + .reg_ubcr = &UBCR9, + .reg_uddr = &UDDR9, + }, + .ep[10] = { + .ep = { + .name = "ep10in-int", + .ops = &pxa25x_ep_ops, + .maxpacket = INT_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = INT_FIFO_SIZE, + .bEndpointAddress = USB_DIR_IN | 10, + .bmAttributes = USB_ENDPOINT_XFER_INT, + .reg_udccs = &UDCCS10, + .reg_uddr = &UDDR10, + }, + + /* third group of endpoints */ + .ep[11] = { + .ep = { + .name = "ep11in-bulk", + .ops = &pxa25x_ep_ops, + .maxpacket = BULK_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = BULK_FIFO_SIZE, + .bEndpointAddress = USB_DIR_IN | 11, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .reg_udccs = &UDCCS11, + .reg_uddr = &UDDR11, + }, + .ep[12] = { + .ep = { + .name = "ep12out-bulk", + .ops = &pxa25x_ep_ops, + .maxpacket = BULK_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = BULK_FIFO_SIZE, + .bEndpointAddress = 12, + .bmAttributes = USB_ENDPOINT_XFER_BULK, + .reg_udccs = &UDCCS12, + .reg_ubcr = &UBCR12, + .reg_uddr = &UDDR12, + }, + .ep[13] = { + .ep = { + .name = "ep13in-iso", + .ops = &pxa25x_ep_ops, + .maxpacket = ISO_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = ISO_FIFO_SIZE, + .bEndpointAddress = USB_DIR_IN | 13, + .bmAttributes = USB_ENDPOINT_XFER_ISOC, + .reg_udccs = &UDCCS13, + .reg_uddr = &UDDR13, + }, + .ep[14] = { + .ep = { + .name = "ep14out-iso", + .ops = &pxa25x_ep_ops, + .maxpacket = ISO_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = ISO_FIFO_SIZE, + .bEndpointAddress = 14, + .bmAttributes = USB_ENDPOINT_XFER_ISOC, + .reg_udccs = &UDCCS14, + .reg_ubcr = &UBCR14, + .reg_uddr = &UDDR14, + }, + .ep[15] = { + .ep = { + .name = "ep15in-int", + .ops = &pxa25x_ep_ops, + .maxpacket = INT_FIFO_SIZE, + }, + .dev = &memory, + .fifo_size = INT_FIFO_SIZE, + .bEndpointAddress = USB_DIR_IN | 15, + .bmAttributes = USB_ENDPOINT_XFER_INT, + .reg_udccs = &UDCCS15, + .reg_uddr = &UDDR15, + }, +#endif /* !CONFIG_USB_PXA25X_SMALL */ +}; + +#define CP15R0_VENDOR_MASK 0xffffe000 + +#if defined(CONFIG_ARCH_PXA) +#define CP15R0_XSCALE_VALUE 0x69052000 /* intel/arm/xscale */ + +#elif defined(CONFIG_ARCH_IXP4XX) +#define CP15R0_XSCALE_VALUE 0x69054000 /* intel/arm/ixp4xx */ + +#endif + +#define CP15R0_PROD_MASK 0x000003f0 +#define PXA25x 0x00000100 /* and PXA26x */ +#define PXA210 0x00000120 + +#define CP15R0_REV_MASK 0x0000000f + +#define CP15R0_PRODREV_MASK (CP15R0_PROD_MASK | CP15R0_REV_MASK) + +#define PXA255_A0 0x00000106 /* or PXA260_B1 */ +#define PXA250_C0 0x00000105 /* or PXA26x_B0 */ +#define PXA250_B2 0x00000104 +#define PXA250_B1 0x00000103 /* or PXA260_A0 */ +#define PXA250_B0 0x00000102 +#define PXA250_A1 0x00000101 +#define PXA250_A0 0x00000100 + +#define PXA210_C0 0x00000125 +#define PXA210_B2 0x00000124 +#define PXA210_B1 0x00000123 +#define PXA210_B0 0x00000122 +#define IXP425_A0 0x000001c1 +#define IXP425_B0 0x000001f1 +#define IXP465_AD 0x00000200 + +/* + * probe - binds to the platform device + */ +static int __init pxa25x_udc_probe(struct platform_device *pdev) +{ + struct pxa25x_udc *dev = &memory; + int retval, vbus_irq, irq; + u32 chiprev; + + /* insist on Intel/ARM/XScale */ + asm("mrc%? p15, 0, %0, c0, c0" : "=r" (chiprev)); + if ((chiprev & CP15R0_VENDOR_MASK) != CP15R0_XSCALE_VALUE) { + pr_err("%s: not XScale!\n", driver_name); + return -ENODEV; + } + + /* trigger chiprev-specific logic */ + switch (chiprev & CP15R0_PRODREV_MASK) { +#if defined(CONFIG_ARCH_PXA) + case PXA255_A0: + dev->has_cfr = 1; + break; + case PXA250_A0: + case PXA250_A1: + /* A0/A1 "not released"; ep 13, 15 unusable */ + /* fall through */ + case PXA250_B2: case PXA210_B2: + case PXA250_B1: case PXA210_B1: + case PXA250_B0: case PXA210_B0: + /* OUT-DMA is broken ... */ + /* fall through */ + case PXA250_C0: case PXA210_C0: + break; +#elif defined(CONFIG_ARCH_IXP4XX) + case IXP425_A0: + case IXP425_B0: + case IXP465_AD: + dev->has_cfr = 1; + break; +#endif + default: + pr_err("%s: unrecognized processor: %08x\n", + driver_name, chiprev); + /* iop3xx, ixp4xx, ... */ + return -ENODEV; + } + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return -ENODEV; + + dev->clk = clk_get(&pdev->dev, "UDCCLK"); + if (IS_ERR(dev->clk)) { + retval = PTR_ERR(dev->clk); + goto err_clk; + } + + pr_debug("%s: IRQ %d%s%s\n", driver_name, irq, + dev->has_cfr ? "" : " (!cfr)", + SIZE_STR "(pio)" + ); + + /* other non-static parts of init */ + dev->dev = &pdev->dev; + dev->mach = pdev->dev.platform_data; + + if (dev->mach->gpio_vbus) { + if ((retval = gpio_request(dev->mach->gpio_vbus, + "pxa25x_udc GPIO VBUS"))) { + dev_dbg(&pdev->dev, + "can't get vbus gpio %d, err: %d\n", + dev->mach->gpio_vbus, retval); + goto err_gpio_vbus; + } + gpio_direction_input(dev->mach->gpio_vbus); + vbus_irq = gpio_to_irq(dev->mach->gpio_vbus); + } else + vbus_irq = 0; + + if (dev->mach->gpio_pullup) { + if ((retval = gpio_request(dev->mach->gpio_pullup, + "pca25x_udc GPIO PULLUP"))) { + dev_dbg(&pdev->dev, + "can't get pullup gpio %d, err: %d\n", + dev->mach->gpio_pullup, retval); + goto err_gpio_pullup; + } + gpio_direction_output(dev->mach->gpio_pullup, 0); + } + + init_timer(&dev->timer); + dev->timer.function = udc_watchdog; + dev->timer.data = (unsigned long) dev; + + device_initialize(&dev->gadget.dev); + dev->gadget.dev.parent = &pdev->dev; + dev->gadget.dev.dma_mask = pdev->dev.dma_mask; + + the_controller = dev; + platform_set_drvdata(pdev, dev); + + udc_disable(dev); + udc_reinit(dev); + + dev->vbus = is_vbus_present(); + + /* irq setup after old hardware state is cleaned up */ + retval = request_irq(irq, pxa25x_udc_irq, + IRQF_DISABLED, driver_name, dev); + if (retval != 0) { + pr_err("%s: can't get irq %d, err %d\n", + driver_name, irq, retval); + goto err_irq1; + } + dev->got_irq = 1; + +#ifdef CONFIG_ARCH_LUBBOCK + if (machine_is_lubbock()) { + retval = request_irq(LUBBOCK_USB_DISC_IRQ, + lubbock_vbus_irq, + IRQF_DISABLED | IRQF_SAMPLE_RANDOM, + driver_name, dev); + if (retval != 0) { + pr_err("%s: can't get irq %i, err %d\n", + driver_name, LUBBOCK_USB_DISC_IRQ, retval); +lubbock_fail0: + goto err_irq_lub; + } + retval = request_irq(LUBBOCK_USB_IRQ, + lubbock_vbus_irq, + IRQF_DISABLED | IRQF_SAMPLE_RANDOM, + driver_name, dev); + if (retval != 0) { + pr_err("%s: can't get irq %i, err %d\n", + driver_name, LUBBOCK_USB_IRQ, retval); + free_irq(LUBBOCK_USB_DISC_IRQ, dev); + goto lubbock_fail0; + } + } else +#endif + if (vbus_irq) { + retval = request_irq(vbus_irq, udc_vbus_irq, + IRQF_DISABLED | IRQF_SAMPLE_RANDOM | + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + driver_name, dev); + if (retval != 0) { + pr_err("%s: can't get irq %i, err %d\n", + driver_name, vbus_irq, retval); + goto err_vbus_irq; + } + } + create_debug_files(dev); + + return 0; + + err_vbus_irq: +#ifdef CONFIG_ARCH_LUBBOCK + free_irq(LUBBOCK_USB_DISC_IRQ, dev); + err_irq_lub: +#endif + free_irq(irq, dev); + err_irq1: + if (dev->mach->gpio_pullup) + gpio_free(dev->mach->gpio_pullup); + err_gpio_pullup: + if (dev->mach->gpio_vbus) + gpio_free(dev->mach->gpio_vbus); + err_gpio_vbus: + clk_put(dev->clk); + err_clk: + return retval; +} + +static void pxa25x_udc_shutdown(struct platform_device *_dev) +{ + pullup_off(); +} + +static int __exit pxa25x_udc_remove(struct platform_device *pdev) +{ + struct pxa25x_udc *dev = platform_get_drvdata(pdev); + + if (dev->driver) + return -EBUSY; + + dev->pullup = 0; + pullup(dev); + + remove_debug_files(dev); + + if (dev->got_irq) { + free_irq(platform_get_irq(pdev, 0), dev); + dev->got_irq = 0; + } +#ifdef CONFIG_ARCH_LUBBOCK + if (machine_is_lubbock()) { + free_irq(LUBBOCK_USB_DISC_IRQ, dev); + free_irq(LUBBOCK_USB_IRQ, dev); + } +#endif + if (dev->mach->gpio_vbus) { + free_irq(gpio_to_irq(dev->mach->gpio_vbus), dev); + gpio_free(dev->mach->gpio_vbus); + } + if (dev->mach->gpio_pullup) + gpio_free(dev->mach->gpio_pullup); + + clk_put(dev->clk); + + platform_set_drvdata(pdev, NULL); + the_controller = NULL; + return 0; +} + +/*-------------------------------------------------------------------------*/ + +#ifdef CONFIG_PM + +/* USB suspend (controlled by the host) and system suspend (controlled + * by the PXA) don't necessarily work well together. If USB is active, + * the 48 MHz clock is required; so the system can't enter 33 MHz idle + * mode, or any deeper PM saving state. + * + * For now, we punt and forcibly disconnect from the USB host when PXA + * enters any suspend state. While we're disconnected, we always disable + * the 48MHz USB clock ... allowing PXA sleep and/or 33 MHz idle states. + * Boards without software pullup control shouldn't use those states. + * VBUS IRQs should probably be ignored so that the PXA device just acts + * "dead" to USB hosts until system resume. + */ +static int pxa25x_udc_suspend(struct platform_device *dev, pm_message_t state) +{ + struct pxa25x_udc *udc = platform_get_drvdata(dev); + unsigned long flags; + + if (!udc->mach->gpio_pullup && !udc->mach->udc_command) + WARN("USB host won't detect disconnect!\n"); + udc->suspended = 1; + + local_irq_save(flags); + pullup(udc); + local_irq_restore(flags); + + return 0; +} + +static int pxa25x_udc_resume(struct platform_device *dev) +{ + struct pxa25x_udc *udc = platform_get_drvdata(dev); + unsigned long flags; + + udc->suspended = 0; + local_irq_save(flags); + pullup(udc); + local_irq_restore(flags); + + return 0; +} + +#else +#define pxa25x_udc_suspend NULL +#define pxa25x_udc_resume NULL +#endif + +/*-------------------------------------------------------------------------*/ + +static struct platform_driver udc_driver = { + .shutdown = pxa25x_udc_shutdown, + .remove = __exit_p(pxa25x_udc_remove), + .suspend = pxa25x_udc_suspend, + .resume = pxa25x_udc_resume, + .driver = { + .owner = THIS_MODULE, + .name = "pxa25x-udc", + }, +}; + +static int __init udc_init(void) +{ + pr_info("%s: version %s\n", driver_name, DRIVER_VERSION); + return platform_driver_probe(&udc_driver, pxa25x_udc_probe); +} +module_init(udc_init); + +static void __exit udc_exit(void) +{ + platform_driver_unregister(&udc_driver); +} +module_exit(udc_exit); + +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_AUTHOR("Frank Becker, Robert Schwebel, David Brownell"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:pxa25x-udc"); diff --git a/drivers/usb/gadget/pxa25x_udc.h b/drivers/usb/gadget/pxa25x_udc.h new file mode 100644 index 00000000000..4d11ece7c95 --- /dev/null +++ b/drivers/usb/gadget/pxa25x_udc.h @@ -0,0 +1,266 @@ +/* + * Intel PXA25x on-chip full speed USB device controller + * + * Copyright (C) 2003 Robert Schwebel , Pengutronix + * Copyright (C) 2003 David Brownell + * + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __LINUX_USB_GADGET_PXA25X_H +#define __LINUX_USB_GADGET_PXA25X_H + +#include + +/*-------------------------------------------------------------------------*/ + +/* pxa25x has this (move to include/asm-arm/arch-pxa/pxa-regs.h) */ +#define UFNRH_SIR (1 << 7) /* SOF interrupt request */ +#define UFNRH_SIM (1 << 6) /* SOF interrupt mask */ +#define UFNRH_IPE14 (1 << 5) /* ISO packet error, ep14 */ +#define UFNRH_IPE9 (1 << 4) /* ISO packet error, ep9 */ +#define UFNRH_IPE4 (1 << 3) /* ISO packet error, ep4 */ + +/* pxa255 has this (move to include/asm-arm/arch-pxa/pxa-regs.h) */ +#define UDCCFR UDC_RES2 /* UDC Control Function Register */ +#define UDCCFR_AREN (1 << 7) /* ACK response enable (now) */ +#define UDCCFR_ACM (1 << 2) /* ACK control mode (wait for AREN) */ + +/* latest pxa255 errata define new "must be one" bits in UDCCFR */ +#define UDCCFR_MB1 (0xff & ~(UDCCFR_AREN|UDCCFR_ACM)) + +/*-------------------------------------------------------------------------*/ + +struct pxa25x_udc; + +struct pxa25x_ep { + struct usb_ep ep; + struct pxa25x_udc *dev; + + const struct usb_endpoint_descriptor *desc; + struct list_head queue; + unsigned long pio_irqs; + + unsigned short fifo_size; + u8 bEndpointAddress; + u8 bmAttributes; + + unsigned stopped : 1; + unsigned dma_fixup : 1; + + /* UDCCS = UDC Control/Status for this EP + * UBCR = UDC Byte Count Remaining (contents of OUT fifo) + * UDDR = UDC Endpoint Data Register (the fifo) + * DRCM = DMA Request Channel Map + */ + volatile u32 *reg_udccs; + volatile u32 *reg_ubcr; + volatile u32 *reg_uddr; +}; + +struct pxa25x_request { + struct usb_request req; + struct list_head queue; +}; + +enum ep0_state { + EP0_IDLE, + EP0_IN_DATA_PHASE, + EP0_OUT_DATA_PHASE, + EP0_END_XFER, + EP0_STALL, +}; + +#define EP0_FIFO_SIZE ((unsigned)16) +#define BULK_FIFO_SIZE ((unsigned)64) +#define ISO_FIFO_SIZE ((unsigned)256) +#define INT_FIFO_SIZE ((unsigned)8) + +struct udc_stats { + struct ep0stats { + unsigned long ops; + unsigned long bytes; + } read, write; + unsigned long irqs; +}; + +#ifdef CONFIG_USB_PXA25X_SMALL +/* when memory's tight, SMALL config saves code+data. */ +#define PXA_UDC_NUM_ENDPOINTS 3 +#endif + +#ifndef PXA_UDC_NUM_ENDPOINTS +#define PXA_UDC_NUM_ENDPOINTS 16 +#endif + +struct pxa25x_udc { + struct usb_gadget gadget; + struct usb_gadget_driver *driver; + + enum ep0_state ep0state; + struct udc_stats stats; + unsigned got_irq : 1, + vbus : 1, + pullup : 1, + has_cfr : 1, + req_pending : 1, + req_std : 1, + req_config : 1, + suspended : 1, + active : 1; + +#define start_watchdog(dev) mod_timer(&dev->timer, jiffies + (HZ/200)) + struct timer_list timer; + + struct device *dev; + struct clk *clk; + struct pxa2xx_udc_mach_info *mach; + u64 dma_mask; + struct pxa25x_ep ep [PXA_UDC_NUM_ENDPOINTS]; + +#ifdef CONFIG_USB_GADGET_DEBUG_FS + struct dentry *debugfs_udc; +#endif +}; + +/*-------------------------------------------------------------------------*/ + +#ifdef CONFIG_ARCH_LUBBOCK +#include +/* lubbock can also report usb connect/disconnect irqs */ +#endif + +static struct pxa25x_udc *the_controller; + +/*-------------------------------------------------------------------------*/ + +/* + * Debugging support vanishes in non-debug builds. DBG_NORMAL should be + * mostly silent during normal use/testing, with no timing side-effects. + */ +#define DBG_NORMAL 1 /* error paths, device state transitions */ +#define DBG_VERBOSE 2 /* add some success path trace info */ +#define DBG_NOISY 3 /* ... even more: request level */ +#define DBG_VERY_NOISY 4 /* ... even more: packet level */ + +#define DMSG(stuff...) pr_debug("udc: " stuff) + +#ifdef DEBUG + +static int is_vbus_present(void); + +static const char *state_name[] = { + "EP0_IDLE", + "EP0_IN_DATA_PHASE", "EP0_OUT_DATA_PHASE", + "EP0_END_XFER", "EP0_STALL" +}; + +#ifdef VERBOSE_DEBUG +# define UDC_DEBUG DBG_VERBOSE +#else +# define UDC_DEBUG DBG_NORMAL +#endif + +static void __maybe_unused +dump_udccr(const char *label) +{ + u32 udccr = UDCCR; + DMSG("%s %02X =%s%s%s%s%s%s%s%s\n", + label, udccr, + (udccr & UDCCR_REM) ? " rem" : "", + (udccr & UDCCR_RSTIR) ? " rstir" : "", + (udccr & UDCCR_SRM) ? " srm" : "", + (udccr & UDCCR_SUSIR) ? " susir" : "", + (udccr & UDCCR_RESIR) ? " resir" : "", + (udccr & UDCCR_RSM) ? " rsm" : "", + (udccr & UDCCR_UDA) ? " uda" : "", + (udccr & UDCCR_UDE) ? " ude" : ""); +} + +static void __maybe_unused +dump_udccs0(const char *label) +{ + u32 udccs0 = UDCCS0; + + DMSG("%s %s %02X =%s%s%s%s%s%s%s%s\n", + label, state_name[the_controller->ep0state], udccs0, + (udccs0 & UDCCS0_SA) ? " sa" : "", + (udccs0 & UDCCS0_RNE) ? " rne" : "", + (udccs0 & UDCCS0_FST) ? " fst" : "", + (udccs0 & UDCCS0_SST) ? " sst" : "", + (udccs0 & UDCCS0_DRWF) ? " dwrf" : "", + (udccs0 & UDCCS0_FTF) ? " ftf" : "", + (udccs0 & UDCCS0_IPR) ? " ipr" : "", + (udccs0 & UDCCS0_OPR) ? " opr" : ""); +} + +static void __maybe_unused +dump_state(struct pxa25x_udc *dev) +{ + u32 tmp; + unsigned i; + + DMSG("%s %s, uicr %02X.%02X, usir %02X.%02x, ufnr %02X.%02X\n", + is_vbus_present() ? "host " : "disconnected", + state_name[dev->ep0state], + UICR1, UICR0, USIR1, USIR0, UFNRH, UFNRL); + dump_udccr("udccr"); + if (dev->has_cfr) { + tmp = UDCCFR; + DMSG("udccfr %02X =%s%s\n", tmp, + (tmp & UDCCFR_AREN) ? " aren" : "", + (tmp & UDCCFR_ACM) ? " acm" : ""); + } + + if (!dev->driver) { + DMSG("no gadget driver bound\n"); + return; + } else + DMSG("ep0 driver '%s'\n", dev->driver->driver.name); + + if (!is_vbus_present()) + return; + + dump_udccs0 ("udccs0"); + DMSG("ep0 IN %lu/%lu, OUT %lu/%lu\n", + dev->stats.write.bytes, dev->stats.write.ops, + dev->stats.read.bytes, dev->stats.read.ops); + + for (i = 1; i < PXA_UDC_NUM_ENDPOINTS; i++) { + if (dev->ep [i].desc == NULL) + continue; + DMSG ("udccs%d = %02x\n", i, *dev->ep->reg_udccs); + } +} + +#else + +#define dump_udccr(x) do{}while(0) +#define dump_udccs0(x) do{}while(0) +#define dump_state(x) do{}while(0) + +#define UDC_DEBUG ((unsigned)0) + +#endif + +#define DBG(lvl, stuff...) do{if ((lvl) <= UDC_DEBUG) DMSG(stuff);}while(0) + +#define ERR(stuff...) pr_err("udc: " stuff) +#define WARN(stuff...) pr_warning("udc: " stuff) +#define INFO(stuff...) pr_info("udc: " stuff) + + +#endif /* __LINUX_USB_GADGET_PXA25X_H */ diff --git a/drivers/usb/gadget/pxa27x_udc.c b/drivers/usb/gadget/pxa27x_udc.c index 40d6b580f15..4771b1314d5 100644 --- a/drivers/usb/gadget/pxa27x_udc.c +++ b/drivers/usb/gadget/pxa27x_udc.c @@ -2367,11 +2367,11 @@ static int pxa_udc_resume(struct platform_device *_dev) #endif /* work with hotplug and coldplug */ -MODULE_ALIAS("platform:pxa2xx-udc"); +MODULE_ALIAS("platform:pxa27x-udc"); static struct platform_driver udc_driver = { .driver = { - .name = "pxa2xx-udc", + .name = "pxa27x-udc", .owner = THIS_MODULE, }, .remove = __exit_p(pxa_udc_remove), diff --git a/drivers/usb/gadget/pxa2xx_udc.c b/drivers/usb/gadget/pxa2xx_udc.c deleted file mode 100644 index 63db96adc0b..00000000000 --- a/drivers/usb/gadget/pxa2xx_udc.c +++ /dev/null @@ -1,2389 +0,0 @@ -/* - * linux/drivers/usb/gadget/pxa2xx_udc.c - * Intel PXA25x and IXP4xx on-chip full speed USB device controllers - * - * Copyright (C) 2002 Intrinsyc, Inc. (Frank Becker) - * Copyright (C) 2003 Robert Schwebel, Pengutronix - * Copyright (C) 2003 Benedikt Spranger, Pengutronix - * Copyright (C) 2003 David Brownell - * Copyright (C) 2003 Joshua Wise - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ - -/* #define VERBOSE_DEBUG */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include -#include -#include - -#include -#include - -/* - * This driver is PXA25x only. Grab the right register definitions. - */ -#ifdef CONFIG_ARCH_PXA -#include -#endif - -#include - - -/* - * This driver handles the USB Device Controller (UDC) in Intel's PXA 25x - * series processors. The UDC for the IXP 4xx series is very similar. - * There are fifteen endpoints, in addition to ep0. - * - * Such controller drivers work with a gadget driver. The gadget driver - * returns descriptors, implements configuration and data protocols used - * by the host to interact with this device, and allocates endpoints to - * the different protocol interfaces. The controller driver virtualizes - * usb hardware so that the gadget drivers will be more portable. - * - * This UDC hardware wants to implement a bit too much USB protocol, so - * it constrains the sorts of USB configuration change events that work. - * The errata for these chips are misleading; some "fixed" bugs from - * pxa250 a0/a1 b0/b1/b2 sure act like they're still there. - * - * Note that the UDC hardware supports DMA (except on IXP) but that's - * not used here. IN-DMA (to host) is simple enough, when the data is - * suitably aligned (16 bytes) ... the network stack doesn't do that, - * other software can. OUT-DMA is buggy in most chip versions, as well - * as poorly designed (data toggle not automatic). So this driver won't - * bother using DMA. (Mostly-working IN-DMA support was available in - * kernels before 2.6.23, but was never enabled or well tested.) - */ - -#define DRIVER_VERSION "30-June-2007" -#define DRIVER_DESC "PXA 25x USB Device Controller driver" - - -static const char driver_name [] = "pxa2xx_udc"; - -static const char ep0name [] = "ep0"; - - -#ifdef CONFIG_ARCH_IXP4XX - -/* cpu-specific register addresses are compiled in to this code */ -#ifdef CONFIG_ARCH_PXA -#error "Can't configure both IXP and PXA" -#endif - -/* IXP doesn't yet support */ -#define clk_get(dev,name) NULL -#define clk_enable(clk) do { } while (0) -#define clk_disable(clk) do { } while (0) -#define clk_put(clk) do { } while (0) - -#endif - -#include "pxa2xx_udc.h" - - -#ifdef CONFIG_USB_PXA2XX_SMALL -#define SIZE_STR " (small)" -#else -#define SIZE_STR "" -#endif - -/* --------------------------------------------------------------------------- - * endpoint related parts of the api to the usb controller hardware, - * used by gadget driver; and the inner talker-to-hardware core. - * --------------------------------------------------------------------------- - */ - -static void pxa2xx_ep_fifo_flush (struct usb_ep *ep); -static void nuke (struct pxa2xx_ep *, int status); - -/* one GPIO should be used to detect VBUS from the host */ -static int is_vbus_present(void) -{ - struct pxa2xx_udc_mach_info *mach = the_controller->mach; - - if (mach->gpio_vbus) { - int value = gpio_get_value(mach->gpio_vbus); - return mach->gpio_vbus_inverted ? !value : value; - } - if (mach->udc_is_connected) - return mach->udc_is_connected(); - return 1; -} - -/* one GPIO should control a D+ pullup, so host sees this device (or not) */ -static void pullup_off(void) -{ - struct pxa2xx_udc_mach_info *mach = the_controller->mach; - - if (mach->gpio_pullup) - gpio_set_value(mach->gpio_pullup, 0); - else if (mach->udc_command) - mach->udc_command(PXA2XX_UDC_CMD_DISCONNECT); -} - -static void pullup_on(void) -{ - struct pxa2xx_udc_mach_info *mach = the_controller->mach; - - if (mach->gpio_pullup) - gpio_set_value(mach->gpio_pullup, 1); - else if (mach->udc_command) - mach->udc_command(PXA2XX_UDC_CMD_CONNECT); -} - -static void pio_irq_enable(int bEndpointAddress) -{ - bEndpointAddress &= 0xf; - if (bEndpointAddress < 8) - UICR0 &= ~(1 << bEndpointAddress); - else { - bEndpointAddress -= 8; - UICR1 &= ~(1 << bEndpointAddress); - } -} - -static void pio_irq_disable(int bEndpointAddress) -{ - bEndpointAddress &= 0xf; - if (bEndpointAddress < 8) - UICR0 |= 1 << bEndpointAddress; - else { - bEndpointAddress -= 8; - UICR1 |= 1 << bEndpointAddress; - } -} - -/* The UDCCR reg contains mask and interrupt status bits, - * so using '|=' isn't safe as it may ack an interrupt. - */ -#define UDCCR_MASK_BITS (UDCCR_REM | UDCCR_SRM | UDCCR_UDE) - -static inline void udc_set_mask_UDCCR(int mask) -{ - UDCCR = (UDCCR & UDCCR_MASK_BITS) | (mask & UDCCR_MASK_BITS); -} - -static inline void udc_clear_mask_UDCCR(int mask) -{ - UDCCR = (UDCCR & UDCCR_MASK_BITS) & ~(mask & UDCCR_MASK_BITS); -} - -static inline void udc_ack_int_UDCCR(int mask) -{ - /* udccr contains the bits we dont want to change */ - __u32 udccr = UDCCR & UDCCR_MASK_BITS; - - UDCCR = udccr | (mask & ~UDCCR_MASK_BITS); -} - -/* - * endpoint enable/disable - * - * we need to verify the descriptors used to enable endpoints. since pxa2xx - * endpoint configurations are fixed, and are pretty much always enabled, - * there's not a lot to manage here. - * - * because pxa2xx can't selectively initialize bulk (or interrupt) endpoints, - * (resetting endpoint halt and toggle), SET_INTERFACE is unusable except - * for a single interface (with only the default altsetting) and for gadget - * drivers that don't halt endpoints (not reset by set_interface). that also - * means that if you use ISO, you must violate the USB spec rule that all - * iso endpoints must be in non-default altsettings. - */ -static int pxa2xx_ep_enable (struct usb_ep *_ep, - const struct usb_endpoint_descriptor *desc) -{ - struct pxa2xx_ep *ep; - struct pxa2xx_udc *dev; - - ep = container_of (_ep, struct pxa2xx_ep, ep); - if (!_ep || !desc || ep->desc || _ep->name == ep0name - || desc->bDescriptorType != USB_DT_ENDPOINT - || ep->bEndpointAddress != desc->bEndpointAddress - || ep->fifo_size < le16_to_cpu - (desc->wMaxPacketSize)) { - DMSG("%s, bad ep or descriptor\n", __func__); - return -EINVAL; - } - - /* xfer types must match, except that interrupt ~= bulk */ - if (ep->bmAttributes != desc->bmAttributes - && ep->bmAttributes != USB_ENDPOINT_XFER_BULK - && desc->bmAttributes != USB_ENDPOINT_XFER_INT) { - DMSG("%s, %s type mismatch\n", __func__, _ep->name); - return -EINVAL; - } - - /* hardware _could_ do smaller, but driver doesn't */ - if ((desc->bmAttributes == USB_ENDPOINT_XFER_BULK - && le16_to_cpu (desc->wMaxPacketSize) - != BULK_FIFO_SIZE) - || !desc->wMaxPacketSize) { - DMSG("%s, bad %s maxpacket\n", __func__, _ep->name); - return -ERANGE; - } - - dev = ep->dev; - if (!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN) { - DMSG("%s, bogus device state\n", __func__); - return -ESHUTDOWN; - } - - ep->desc = desc; - ep->stopped = 0; - ep->pio_irqs = 0; - ep->ep.maxpacket = le16_to_cpu (desc->wMaxPacketSize); - - /* flush fifo (mostly for OUT buffers) */ - pxa2xx_ep_fifo_flush (_ep); - - /* ... reset halt state too, if we could ... */ - - DBG(DBG_VERBOSE, "enabled %s\n", _ep->name); - return 0; -} - -static int pxa2xx_ep_disable (struct usb_ep *_ep) -{ - struct pxa2xx_ep *ep; - unsigned long flags; - - ep = container_of (_ep, struct pxa2xx_ep, ep); - if (!_ep || !ep->desc) { - DMSG("%s, %s not enabled\n", __func__, - _ep ? ep->ep.name : NULL); - return -EINVAL; - } - local_irq_save(flags); - - nuke (ep, -ESHUTDOWN); - - /* flush fifo (mostly for IN buffers) */ - pxa2xx_ep_fifo_flush (_ep); - - ep->desc = NULL; - ep->stopped = 1; - - local_irq_restore(flags); - DBG(DBG_VERBOSE, "%s disabled\n", _ep->name); - return 0; -} - -/*-------------------------------------------------------------------------*/ - -/* for the pxa2xx, these can just wrap kmalloc/kfree. gadget drivers - * must still pass correctly initialized endpoints, since other controller - * drivers may care about how it's currently set up (dma issues etc). - */ - -/* - * pxa2xx_ep_alloc_request - allocate a request data structure - */ -static struct usb_request * -pxa2xx_ep_alloc_request (struct usb_ep *_ep, gfp_t gfp_flags) -{ - struct pxa2xx_request *req; - - req = kzalloc(sizeof(*req), gfp_flags); - if (!req) - return NULL; - - INIT_LIST_HEAD (&req->queue); - return &req->req; -} - - -/* - * pxa2xx_ep_free_request - deallocate a request data structure - */ -static void -pxa2xx_ep_free_request (struct usb_ep *_ep, struct usb_request *_req) -{ - struct pxa2xx_request *req; - - req = container_of (_req, struct pxa2xx_request, req); - WARN_ON (!list_empty (&req->queue)); - kfree(req); -} - -/*-------------------------------------------------------------------------*/ - -/* - * done - retire a request; caller blocked irqs - */ -static void done(struct pxa2xx_ep *ep, struct pxa2xx_request *req, int status) -{ - unsigned stopped = ep->stopped; - - list_del_init(&req->queue); - - if (likely (req->req.status == -EINPROGRESS)) - req->req.status = status; - else - status = req->req.status; - - if (status && status != -ESHUTDOWN) - DBG(DBG_VERBOSE, "complete %s req %p stat %d len %u/%u\n", - ep->ep.name, &req->req, status, - req->req.actual, req->req.length); - - /* don't modify queue heads during completion callback */ - ep->stopped = 1; - req->req.complete(&ep->ep, &req->req); - ep->stopped = stopped; -} - - -static inline void ep0_idle (struct pxa2xx_udc *dev) -{ - dev->ep0state = EP0_IDLE; -} - -static int -write_packet(volatile u32 *uddr, struct pxa2xx_request *req, unsigned max) -{ - u8 *buf; - unsigned length, count; - - buf = req->req.buf + req->req.actual; - prefetch(buf); - - /* how big will this packet be? */ - length = min(req->req.length - req->req.actual, max); - req->req.actual += length; - - count = length; - while (likely(count--)) - *uddr = *buf++; - - return length; -} - -/* - * write to an IN endpoint fifo, as many packets as possible. - * irqs will use this to write the rest later. - * caller guarantees at least one packet buffer is ready (or a zlp). - */ -static int -write_fifo (struct pxa2xx_ep *ep, struct pxa2xx_request *req) -{ - unsigned max; - - max = le16_to_cpu(ep->desc->wMaxPacketSize); - do { - unsigned count; - int is_last, is_short; - - count = write_packet(ep->reg_uddr, req, max); - - /* last packet is usually short (or a zlp) */ - if (unlikely (count != max)) - is_last = is_short = 1; - else { - if (likely(req->req.length != req->req.actual) - || req->req.zero) - is_last = 0; - else - is_last = 1; - /* interrupt/iso maxpacket may not fill the fifo */ - is_short = unlikely (max < ep->fifo_size); - } - - DBG(DBG_VERY_NOISY, "wrote %s %d bytes%s%s %d left %p\n", - ep->ep.name, count, - is_last ? "/L" : "", is_short ? "/S" : "", - req->req.length - req->req.actual, req); - - /* let loose that packet. maybe try writing another one, - * double buffering might work. TSP, TPC, and TFS - * bit values are the same for all normal IN endpoints. - */ - *ep->reg_udccs = UDCCS_BI_TPC; - if (is_short) - *ep->reg_udccs = UDCCS_BI_TSP; - - /* requests complete when all IN data is in the FIFO */ - if (is_last) { - done (ep, req, 0); - if (list_empty(&ep->queue)) - pio_irq_disable (ep->bEndpointAddress); - return 1; - } - - // TODO experiment: how robust can fifo mode tweaking be? - // double buffering is off in the default fifo mode, which - // prevents TFS from being set here. - - } while (*ep->reg_udccs & UDCCS_BI_TFS); - return 0; -} - -/* caller asserts req->pending (ep0 irq status nyet cleared); starts - * ep0 data stage. these chips want very simple state transitions. - */ -static inline -void ep0start(struct pxa2xx_udc *dev, u32 flags, const char *tag) -{ - UDCCS0 = flags|UDCCS0_SA|UDCCS0_OPR; - USIR0 = USIR0_IR0; - dev->req_pending = 0; - DBG(DBG_VERY_NOISY, "%s %s, %02x/%02x\n", - __func__, tag, UDCCS0, flags); -} - -static int -write_ep0_fifo (struct pxa2xx_ep *ep, struct pxa2xx_request *req) -{ - unsigned count; - int is_short; - - count = write_packet(&UDDR0, req, EP0_FIFO_SIZE); - ep->dev->stats.write.bytes += count; - - /* last packet "must be" short (or a zlp) */ - is_short = (count != EP0_FIFO_SIZE); - - DBG(DBG_VERY_NOISY, "ep0in %d bytes %d left %p\n", count, - req->req.length - req->req.actual, req); - - if (unlikely (is_short)) { - if (ep->dev->req_pending) - ep0start(ep->dev, UDCCS0_IPR, "short IN"); - else - UDCCS0 = UDCCS0_IPR; - - count = req->req.length; - done (ep, req, 0); - ep0_idle(ep->dev); -#ifndef CONFIG_ARCH_IXP4XX -#if 1 - /* This seems to get rid of lost status irqs in some cases: - * host responds quickly, or next request involves config - * change automagic, or should have been hidden, or ... - * - * FIXME get rid of all udelays possible... - */ - if (count >= EP0_FIFO_SIZE) { - count = 100; - do { - if ((UDCCS0 & UDCCS0_OPR) != 0) { - /* clear OPR, generate ack */ - UDCCS0 = UDCCS0_OPR; - break; - } - count--; - udelay(1); - } while (count); - } -#endif -#endif - } else if (ep->dev->req_pending) - ep0start(ep->dev, 0, "IN"); - return is_short; -} - - -/* - * read_fifo - unload packet(s) from the fifo we use for usb OUT - * transfers and put them into the request. caller should have made - * sure there's at least one packet ready. - * - * returns true if the request completed because of short packet or the - * request buffer having filled (and maybe overran till end-of-packet). - */ -static int -read_fifo (struct pxa2xx_ep *ep, struct pxa2xx_request *req) -{ - for (;;) { - u32 udccs; - u8 *buf; - unsigned bufferspace, count, is_short; - - /* make sure there's a packet in the FIFO. - * UDCCS_{BO,IO}_RPC are all the same bit value. - * UDCCS_{BO,IO}_RNE are all the same bit value. - */ - udccs = *ep->reg_udccs; - if (unlikely ((udccs & UDCCS_BO_RPC) == 0)) - break; - buf = req->req.buf + req->req.actual; - prefetchw(buf); - bufferspace = req->req.length - req->req.actual; - - /* read all bytes from this packet */ - if (likely (udccs & UDCCS_BO_RNE)) { - count = 1 + (0x0ff & *ep->reg_ubcr); - req->req.actual += min (count, bufferspace); - } else /* zlp */ - count = 0; - is_short = (count < ep->ep.maxpacket); - DBG(DBG_VERY_NOISY, "read %s %02x, %d bytes%s req %p %d/%d\n", - ep->ep.name, udccs, count, - is_short ? "/S" : "", - req, req->req.actual, req->req.length); - while (likely (count-- != 0)) { - u8 byte = (u8) *ep->reg_uddr; - - if (unlikely (bufferspace == 0)) { - /* this happens when the driver's buffer - * is smaller than what the host sent. - * discard the extra data. - */ - if (req->req.status != -EOVERFLOW) - DMSG("%s overflow %d\n", - ep->ep.name, count); - req->req.status = -EOVERFLOW; - } else { - *buf++ = byte; - bufferspace--; - } - } - *ep->reg_udccs = UDCCS_BO_RPC; - /* RPC/RSP/RNE could now reflect the other packet buffer */ - - /* iso is one request per packet */ - if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) { - if (udccs & UDCCS_IO_ROF) - req->req.status = -EHOSTUNREACH; - /* more like "is_done" */ - is_short = 1; - } - - /* completion */ - if (is_short || req->req.actual == req->req.length) { - done (ep, req, 0); - if (list_empty(&ep->queue)) - pio_irq_disable (ep->bEndpointAddress); - return 1; - } - - /* finished that packet. the next one may be waiting... */ - } - return 0; -} - -/* - * special ep0 version of the above. no UBCR0 or double buffering; status - * handshaking is magic. most device protocols don't need control-OUT. - * CDC vendor commands (and RNDIS), mass storage CB/CBI, and some other - * protocols do use them. - */ -static int -read_ep0_fifo (struct pxa2xx_ep *ep, struct pxa2xx_request *req) -{ - u8 *buf, byte; - unsigned bufferspace; - - buf = req->req.buf + req->req.actual; - bufferspace = req->req.length - req->req.actual; - - while (UDCCS0 & UDCCS0_RNE) { - byte = (u8) UDDR0; - - if (unlikely (bufferspace == 0)) { - /* this happens when the driver's buffer - * is smaller than what the host sent. - * discard the extra data. - */ - if (req->req.status != -EOVERFLOW) - DMSG("%s overflow\n", ep->ep.name); - req->req.status = -EOVERFLOW; - } else { - *buf++ = byte; - req->req.actual++; - bufferspace--; - } - } - - UDCCS0 = UDCCS0_OPR | UDCCS0_IPR; - - /* completion */ - if (req->req.actual >= req->req.length) - return 1; - - /* finished that packet. the next one may be waiting... */ - return 0; -} - -/*-------------------------------------------------------------------------*/ - -static int -pxa2xx_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags) -{ - struct pxa2xx_request *req; - struct pxa2xx_ep *ep; - struct pxa2xx_udc *dev; - unsigned long flags; - - req = container_of(_req, struct pxa2xx_request, req); - if (unlikely (!_req || !_req->complete || !_req->buf - || !list_empty(&req->queue))) { - DMSG("%s, bad params\n", __func__); - return -EINVAL; - } - - ep = container_of(_ep, struct pxa2xx_ep, ep); - if (unlikely (!_ep || (!ep->desc && ep->ep.name != ep0name))) { - DMSG("%s, bad ep\n", __func__); - return -EINVAL; - } - - dev = ep->dev; - if (unlikely (!dev->driver - || dev->gadget.speed == USB_SPEED_UNKNOWN)) { - DMSG("%s, bogus device state\n", __func__); - return -ESHUTDOWN; - } - - /* iso is always one packet per request, that's the only way - * we can report per-packet status. that also helps with dma. - */ - if (unlikely (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC - && req->req.length > le16_to_cpu - (ep->desc->wMaxPacketSize))) - return -EMSGSIZE; - - DBG(DBG_NOISY, "%s queue req %p, len %d buf %p\n", - _ep->name, _req, _req->length, _req->buf); - - local_irq_save(flags); - - _req->status = -EINPROGRESS; - _req->actual = 0; - - /* kickstart this i/o queue? */ - if (list_empty(&ep->queue) && !ep->stopped) { - if (ep->desc == NULL/* ep0 */) { - unsigned length = _req->length; - - switch (dev->ep0state) { - case EP0_IN_DATA_PHASE: - dev->stats.write.ops++; - if (write_ep0_fifo(ep, req)) - req = NULL; - break; - - case EP0_OUT_DATA_PHASE: - dev->stats.read.ops++; - /* messy ... */ - if (dev->req_config) { - DBG(DBG_VERBOSE, "ep0 config ack%s\n", - dev->has_cfr ? "" : " raced"); - if (dev->has_cfr) - UDCCFR = UDCCFR_AREN|UDCCFR_ACM - |UDCCFR_MB1; - done(ep, req, 0); - dev->ep0state = EP0_END_XFER; - local_irq_restore (flags); - return 0; - } - if (dev->req_pending) - ep0start(dev, UDCCS0_IPR, "OUT"); - if (length == 0 || ((UDCCS0 & UDCCS0_RNE) != 0 - && read_ep0_fifo(ep, req))) { - ep0_idle(dev); - done(ep, req, 0); - req = NULL; - } - break; - - default: - DMSG("ep0 i/o, odd state %d\n", dev->ep0state); - local_irq_restore (flags); - return -EL2HLT; - } - /* can the FIFO can satisfy the request immediately? */ - } else if ((ep->bEndpointAddress & USB_DIR_IN) != 0) { - if ((*ep->reg_udccs & UDCCS_BI_TFS) != 0 - && write_fifo(ep, req)) - req = NULL; - } else if ((*ep->reg_udccs & UDCCS_BO_RFS) != 0 - && read_fifo(ep, req)) { - req = NULL; - } - - if (likely (req && ep->desc)) - pio_irq_enable(ep->bEndpointAddress); - } - - /* pio or dma irq handler advances the queue. */ - if (likely(req != NULL)) - list_add_tail(&req->queue, &ep->queue); - local_irq_restore(flags); - - return 0; -} - - -/* - * nuke - dequeue ALL requests - */ -static void nuke(struct pxa2xx_ep *ep, int status) -{ - struct pxa2xx_request *req; - - /* called with irqs blocked */ - while (!list_empty(&ep->queue)) { - req = list_entry(ep->queue.next, - struct pxa2xx_request, - queue); - done(ep, req, status); - } - if (ep->desc) - pio_irq_disable (ep->bEndpointAddress); -} - - -/* dequeue JUST ONE request */ -static int pxa2xx_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) -{ - struct pxa2xx_ep *ep; - struct pxa2xx_request *req; - unsigned long flags; - - ep = container_of(_ep, struct pxa2xx_ep, ep); - if (!_ep || ep->ep.name == ep0name) - return -EINVAL; - - local_irq_save(flags); - - /* make sure it's actually queued on this endpoint */ - list_for_each_entry (req, &ep->queue, queue) { - if (&req->req == _req) - break; - } - if (&req->req != _req) { - local_irq_restore(flags); - return -EINVAL; - } - - done(ep, req, -ECONNRESET); - - local_irq_restore(flags); - return 0; -} - -/*-------------------------------------------------------------------------*/ - -static int pxa2xx_ep_set_halt(struct usb_ep *_ep, int value) -{ - struct pxa2xx_ep *ep; - unsigned long flags; - - ep = container_of(_ep, struct pxa2xx_ep, ep); - if (unlikely (!_ep - || (!ep->desc && ep->ep.name != ep0name)) - || ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) { - DMSG("%s, bad ep\n", __func__); - return -EINVAL; - } - if (value == 0) { - /* this path (reset toggle+halt) is needed to implement - * SET_INTERFACE on normal hardware. but it can't be - * done from software on the PXA UDC, and the hardware - * forgets to do it as part of SET_INTERFACE automagic. - */ - DMSG("only host can clear %s halt\n", _ep->name); - return -EROFS; - } - - local_irq_save(flags); - - if ((ep->bEndpointAddress & USB_DIR_IN) != 0 - && ((*ep->reg_udccs & UDCCS_BI_TFS) == 0 - || !list_empty(&ep->queue))) { - local_irq_restore(flags); - return -EAGAIN; - } - - /* FST bit is the same for control, bulk in, bulk out, interrupt in */ - *ep->reg_udccs = UDCCS_BI_FST|UDCCS_BI_FTF; - - /* ep0 needs special care */ - if (!ep->desc) { - start_watchdog(ep->dev); - ep->dev->req_pending = 0; - ep->dev->ep0state = EP0_STALL; - - /* and bulk/intr endpoints like dropping stalls too */ - } else { - unsigned i; - for (i = 0; i < 1000; i += 20) { - if (*ep->reg_udccs & UDCCS_BI_SST) - break; - udelay(20); - } - } - local_irq_restore(flags); - - DBG(DBG_VERBOSE, "%s halt\n", _ep->name); - return 0; -} - -static int pxa2xx_ep_fifo_status(struct usb_ep *_ep) -{ - struct pxa2xx_ep *ep; - - ep = container_of(_ep, struct pxa2xx_ep, ep); - if (!_ep) { - DMSG("%s, bad ep\n", __func__); - return -ENODEV; - } - /* pxa can't report unclaimed bytes from IN fifos */ - if ((ep->bEndpointAddress & USB_DIR_IN) != 0) - return -EOPNOTSUPP; - if (ep->dev->gadget.speed == USB_SPEED_UNKNOWN - || (*ep->reg_udccs & UDCCS_BO_RFS) == 0) - return 0; - else - return (*ep->reg_ubcr & 0xfff) + 1; -} - -static void pxa2xx_ep_fifo_flush(struct usb_ep *_ep) -{ - struct pxa2xx_ep *ep; - - ep = container_of(_ep, struct pxa2xx_ep, ep); - if (!_ep || ep->ep.name == ep0name || !list_empty(&ep->queue)) { - DMSG("%s, bad ep\n", __func__); - return; - } - - /* toggle and halt bits stay unchanged */ - - /* for OUT, just read and discard the FIFO contents. */ - if ((ep->bEndpointAddress & USB_DIR_IN) == 0) { - while (((*ep->reg_udccs) & UDCCS_BO_RNE) != 0) - (void) *ep->reg_uddr; - return; - } - - /* most IN status is the same, but ISO can't stall */ - *ep->reg_udccs = UDCCS_BI_TPC|UDCCS_BI_FTF|UDCCS_BI_TUR - | (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) - ? 0 : UDCCS_BI_SST; -} - - -static struct usb_ep_ops pxa2xx_ep_ops = { - .enable = pxa2xx_ep_enable, - .disable = pxa2xx_ep_disable, - - .alloc_request = pxa2xx_ep_alloc_request, - .free_request = pxa2xx_ep_free_request, - - .queue = pxa2xx_ep_queue, - .dequeue = pxa2xx_ep_dequeue, - - .set_halt = pxa2xx_ep_set_halt, - .fifo_status = pxa2xx_ep_fifo_status, - .fifo_flush = pxa2xx_ep_fifo_flush, -}; - - -/* --------------------------------------------------------------------------- - * device-scoped parts of the api to the usb controller hardware - * --------------------------------------------------------------------------- - */ - -static int pxa2xx_udc_get_frame(struct usb_gadget *_gadget) -{ - return ((UFNRH & 0x07) << 8) | (UFNRL & 0xff); -} - -static int pxa2xx_udc_wakeup(struct usb_gadget *_gadget) -{ - /* host may not have enabled remote wakeup */ - if ((UDCCS0 & UDCCS0_DRWF) == 0) - return -EHOSTUNREACH; - udc_set_mask_UDCCR(UDCCR_RSM); - return 0; -} - -static void stop_activity(struct pxa2xx_udc *, struct usb_gadget_driver *); -static void udc_enable (struct pxa2xx_udc *); -static void udc_disable(struct pxa2xx_udc *); - -/* We disable the UDC -- and its 48 MHz clock -- whenever it's not - * in active use. - */ -static int pullup(struct pxa2xx_udc *udc) -{ - int is_active = udc->vbus && udc->pullup && !udc->suspended; - DMSG("%s\n", is_active ? "active" : "inactive"); - if (is_active) { - if (!udc->active) { - udc->active = 1; - /* Enable clock for USB device */ - clk_enable(udc->clk); - udc_enable(udc); - } - } else { - if (udc->active) { - if (udc->gadget.speed != USB_SPEED_UNKNOWN) { - DMSG("disconnect %s\n", udc->driver - ? udc->driver->driver.name - : "(no driver)"); - stop_activity(udc, udc->driver); - } - udc_disable(udc); - /* Disable clock for USB device */ - clk_disable(udc->clk); - udc->active = 0; - } - - } - return 0; -} - -/* VBUS reporting logically comes from a transceiver */ -static int pxa2xx_udc_vbus_session(struct usb_gadget *_gadget, int is_active) -{ - struct pxa2xx_udc *udc; - - udc = container_of(_gadget, struct pxa2xx_udc, gadget); - udc->vbus = (is_active != 0); - DMSG("vbus %s\n", is_active ? "supplied" : "inactive"); - pullup(udc); - return 0; -} - -/* drivers may have software control over D+ pullup */ -static int pxa2xx_udc_pullup(struct usb_gadget *_gadget, int is_active) -{ - struct pxa2xx_udc *udc; - - udc = container_of(_gadget, struct pxa2xx_udc, gadget); - - /* not all boards support pullup control */ - if (!udc->mach->gpio_pullup && !udc->mach->udc_command) - return -EOPNOTSUPP; - - udc->pullup = (is_active != 0); - pullup(udc); - return 0; -} - -static const struct usb_gadget_ops pxa2xx_udc_ops = { - .get_frame = pxa2xx_udc_get_frame, - .wakeup = pxa2xx_udc_wakeup, - .vbus_session = pxa2xx_udc_vbus_session, - .pullup = pxa2xx_udc_pullup, - - // .vbus_draw ... boards may consume current from VBUS, up to - // 100-500mA based on config. the 500uA suspend ceiling means - // that exclusively vbus-powered PXA designs violate USB specs. -}; - -/*-------------------------------------------------------------------------*/ - -#ifdef CONFIG_USB_GADGET_DEBUG_FS - -static int -udc_seq_show(struct seq_file *m, void *_d) -{ - struct pxa2xx_udc *dev = m->private; - unsigned long flags; - int i; - u32 tmp; - - local_irq_save(flags); - - /* basic device status */ - seq_printf(m, DRIVER_DESC "\n" - "%s version: %s\nGadget driver: %s\nHost %s\n\n", - driver_name, DRIVER_VERSION SIZE_STR "(pio)", - dev->driver ? dev->driver->driver.name : "(none)", - is_vbus_present() ? "full speed" : "disconnected"); - - /* registers for device and ep0 */ - seq_printf(m, - "uicr %02X.%02X, usir %02X.%02x, ufnr %02X.%02X\n", - UICR1, UICR0, USIR1, USIR0, UFNRH, UFNRL); - - tmp = UDCCR; - seq_printf(m, - "udccr %02X =%s%s%s%s%s%s%s%s\n", tmp, - (tmp & UDCCR_REM) ? " rem" : "", - (tmp & UDCCR_RSTIR) ? " rstir" : "", - (tmp & UDCCR_SRM) ? " srm" : "", - (tmp & UDCCR_SUSIR) ? " susir" : "", - (tmp & UDCCR_RESIR) ? " resir" : "", - (tmp & UDCCR_RSM) ? " rsm" : "", - (tmp & UDCCR_UDA) ? " uda" : "", - (tmp & UDCCR_UDE) ? " ude" : ""); - - tmp = UDCCS0; - seq_printf(m, - "udccs0 %02X =%s%s%s%s%s%s%s%s\n", tmp, - (tmp & UDCCS0_SA) ? " sa" : "", - (tmp & UDCCS0_RNE) ? " rne" : "", - (tmp & UDCCS0_FST) ? " fst" : "", - (tmp & UDCCS0_SST) ? " sst" : "", - (tmp & UDCCS0_DRWF) ? " dwrf" : "", - (tmp & UDCCS0_FTF) ? " ftf" : "", - (tmp & UDCCS0_IPR) ? " ipr" : "", - (tmp & UDCCS0_OPR) ? " opr" : ""); - - if (dev->has_cfr) { - tmp = UDCCFR; - seq_printf(m, - "udccfr %02X =%s%s\n", tmp, - (tmp & UDCCFR_AREN) ? " aren" : "", - (tmp & UDCCFR_ACM) ? " acm" : ""); - } - - if (!is_vbus_present() || !dev->driver) - goto done; - - seq_printf(m, "ep0 IN %lu/%lu, OUT %lu/%lu\nirqs %lu\n\n", - dev->stats.write.bytes, dev->stats.write.ops, - dev->stats.read.bytes, dev->stats.read.ops, - dev->stats.irqs); - - /* dump endpoint queues */ - for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) { - struct pxa2xx_ep *ep = &dev->ep [i]; - struct pxa2xx_request *req; - - if (i != 0) { - const struct usb_endpoint_descriptor *desc; - - desc = ep->desc; - if (!desc) - continue; - tmp = *dev->ep [i].reg_udccs; - seq_printf(m, - "%s max %d %s udccs %02x irqs %lu\n", - ep->ep.name, le16_to_cpu(desc->wMaxPacketSize), - "pio", tmp, ep->pio_irqs); - /* TODO translate all five groups of udccs bits! */ - - } else /* ep0 should only have one transfer queued */ - seq_printf(m, "ep0 max 16 pio irqs %lu\n", - ep->pio_irqs); - - if (list_empty(&ep->queue)) { - seq_printf(m, "\t(nothing queued)\n"); - continue; - } - list_for_each_entry(req, &ep->queue, queue) { - seq_printf(m, - "\treq %p len %d/%d buf %p\n", - &req->req, req->req.actual, - req->req.length, req->req.buf); - } - } - -done: - local_irq_restore(flags); - return 0; -} - -static int -udc_debugfs_open(struct inode *inode, struct file *file) -{ - return single_open(file, udc_seq_show, inode->i_private); -} - -static const struct file_operations debug_fops = { - .open = udc_debugfs_open, - .read = seq_read, - .llseek = seq_lseek, - .release = single_release, - .owner = THIS_MODULE, -}; - -#define create_debug_files(dev) \ - do { \ - dev->debugfs_udc = debugfs_create_file(dev->gadget.name, \ - S_IRUGO, NULL, dev, &debug_fops); \ - } while (0) -#define remove_debug_files(dev) \ - do { \ - if (dev->debugfs_udc) \ - debugfs_remove(dev->debugfs_udc); \ - } while (0) - -#else /* !CONFIG_USB_GADGET_DEBUG_FILES */ - -#define create_debug_files(dev) do {} while (0) -#define remove_debug_files(dev) do {} while (0) - -#endif /* CONFIG_USB_GADGET_DEBUG_FILES */ - -/*-------------------------------------------------------------------------*/ - -/* - * udc_disable - disable USB device controller - */ -static void udc_disable(struct pxa2xx_udc *dev) -{ - /* block all irqs */ - udc_set_mask_UDCCR(UDCCR_SRM|UDCCR_REM); - UICR0 = UICR1 = 0xff; - UFNRH = UFNRH_SIM; - - /* if hardware supports it, disconnect from usb */ - pullup_off(); - - udc_clear_mask_UDCCR(UDCCR_UDE); - - ep0_idle (dev); - dev->gadget.speed = USB_SPEED_UNKNOWN; -} - - -/* - * udc_reinit - initialize software state - */ -static void udc_reinit(struct pxa2xx_udc *dev) -{ - u32 i; - - /* device/ep0 records init */ - INIT_LIST_HEAD (&dev->gadget.ep_list); - INIT_LIST_HEAD (&dev->gadget.ep0->ep_list); - dev->ep0state = EP0_IDLE; - - /* basic endpoint records init */ - for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) { - struct pxa2xx_ep *ep = &dev->ep[i]; - - if (i != 0) - list_add_tail (&ep->ep.ep_list, &dev->gadget.ep_list); - - ep->desc = NULL; - ep->stopped = 0; - INIT_LIST_HEAD (&ep->queue); - ep->pio_irqs = 0; - } - - /* the rest was statically initialized, and is read-only */ -} - -/* until it's enabled, this UDC should be completely invisible - * to any USB host. - */ -static void udc_enable (struct pxa2xx_udc *dev) -{ - udc_clear_mask_UDCCR(UDCCR_UDE); - - /* try to clear these bits before we enable the udc */ - udc_ack_int_UDCCR(UDCCR_SUSIR|/*UDCCR_RSTIR|*/UDCCR_RESIR); - - ep0_idle(dev); - dev->gadget.speed = USB_SPEED_UNKNOWN; - dev->stats.irqs = 0; - - /* - * sequence taken from chapter 12.5.10, PXA250 AppProcDevManual: - * - enable UDC - * - if RESET is already in progress, ack interrupt - * - unmask reset interrupt - */ - udc_set_mask_UDCCR(UDCCR_UDE); - if (!(UDCCR & UDCCR_UDA)) - udc_ack_int_UDCCR(UDCCR_RSTIR); - - if (dev->has_cfr /* UDC_RES2 is defined */) { - /* pxa255 (a0+) can avoid a set_config race that could - * prevent gadget drivers from configuring correctly - */ - UDCCFR = UDCCFR_ACM | UDCCFR_MB1; - } else { - /* "USB test mode" for pxa250 errata 40-42 (stepping a0, a1) - * which could result in missing packets and interrupts. - * supposedly one bit per endpoint, controlling whether it - * double buffers or not; ACM/AREN bits fit into the holes. - * zero bits (like USIR0_IRx) disable double buffering. - */ - UDC_RES1 = 0x00; - UDC_RES2 = 0x00; - } - - /* enable suspend/resume and reset irqs */ - udc_clear_mask_UDCCR(UDCCR_SRM | UDCCR_REM); - - /* enable ep0 irqs */ - UICR0 &= ~UICR0_IM0; - - /* if hardware supports it, pullup D+ and wait for reset */ - pullup_on(); -} - - -/* when a driver is successfully registered, it will receive - * control requests including set_configuration(), which enables - * non-control requests. then usb traffic follows until a - * disconnect is reported. then a host may connect again, or - * the driver might get unbound. - */ -int usb_gadget_register_driver(struct usb_gadget_driver *driver) -{ - struct pxa2xx_udc *dev = the_controller; - int retval; - - if (!driver - || driver->speed < USB_SPEED_FULL - || !driver->bind - || !driver->disconnect - || !driver->setup) - return -EINVAL; - if (!dev) - return -ENODEV; - if (dev->driver) - return -EBUSY; - - /* first hook up the driver ... */ - dev->driver = driver; - dev->gadget.dev.driver = &driver->driver; - dev->pullup = 1; - - retval = device_add (&dev->gadget.dev); - if (retval) { -fail: - dev->driver = NULL; - dev->gadget.dev.driver = NULL; - return retval; - } - retval = driver->bind(&dev->gadget); - if (retval) { - DMSG("bind to driver %s --> error %d\n", - driver->driver.name, retval); - device_del (&dev->gadget.dev); - goto fail; - } - - /* ... then enable host detection and ep0; and we're ready - * for set_configuration as well as eventual disconnect. - */ - DMSG("registered gadget driver '%s'\n", driver->driver.name); - pullup(dev); - dump_state(dev); - return 0; -} -EXPORT_SYMBOL(usb_gadget_register_driver); - -static void -stop_activity(struct pxa2xx_udc *dev, struct usb_gadget_driver *driver) -{ - int i; - - /* don't disconnect drivers more than once */ - if (dev->gadget.speed == USB_SPEED_UNKNOWN) - driver = NULL; - dev->gadget.speed = USB_SPEED_UNKNOWN; - - /* prevent new request submissions, kill any outstanding requests */ - for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) { - struct pxa2xx_ep *ep = &dev->ep[i]; - - ep->stopped = 1; - nuke(ep, -ESHUTDOWN); - } - del_timer_sync(&dev->timer); - - /* report disconnect; the driver is already quiesced */ - if (driver) - driver->disconnect(&dev->gadget); - - /* re-init driver-visible data structures */ - udc_reinit(dev); -} - -int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) -{ - struct pxa2xx_udc *dev = the_controller; - - if (!dev) - return -ENODEV; - if (!driver || driver != dev->driver || !driver->unbind) - return -EINVAL; - - local_irq_disable(); - dev->pullup = 0; - pullup(dev); - stop_activity(dev, driver); - local_irq_enable(); - - driver->unbind(&dev->gadget); - dev->gadget.dev.driver = NULL; - dev->driver = NULL; - - device_del (&dev->gadget.dev); - - DMSG("unregistered gadget driver '%s'\n", driver->driver.name); - dump_state(dev); - return 0; -} -EXPORT_SYMBOL(usb_gadget_unregister_driver); - - -/*-------------------------------------------------------------------------*/ - -#ifdef CONFIG_ARCH_LUBBOCK - -/* Lubbock has separate connect and disconnect irqs. More typical designs - * use one GPIO as the VBUS IRQ, and another to control the D+ pullup. - */ - -static irqreturn_t -lubbock_vbus_irq(int irq, void *_dev) -{ - struct pxa2xx_udc *dev = _dev; - int vbus; - - dev->stats.irqs++; - switch (irq) { - case LUBBOCK_USB_IRQ: - vbus = 1; - disable_irq(LUBBOCK_USB_IRQ); - enable_irq(LUBBOCK_USB_DISC_IRQ); - break; - case LUBBOCK_USB_DISC_IRQ: - vbus = 0; - disable_irq(LUBBOCK_USB_DISC_IRQ); - enable_irq(LUBBOCK_USB_IRQ); - break; - default: - return IRQ_NONE; - } - - pxa2xx_udc_vbus_session(&dev->gadget, vbus); - return IRQ_HANDLED; -} - -#endif - -static irqreturn_t udc_vbus_irq(int irq, void *_dev) -{ - struct pxa2xx_udc *dev = _dev; - int vbus = gpio_get_value(dev->mach->gpio_vbus); - - if (dev->mach->gpio_vbus_inverted) - vbus = !vbus; - - pxa2xx_udc_vbus_session(&dev->gadget, vbus); - return IRQ_HANDLED; -} - - -/*-------------------------------------------------------------------------*/ - -static inline void clear_ep_state (struct pxa2xx_udc *dev) -{ - unsigned i; - - /* hardware SET_{CONFIGURATION,INTERFACE} automagic resets endpoint - * fifos, and pending transactions mustn't be continued in any case. - */ - for (i = 1; i < PXA_UDC_NUM_ENDPOINTS; i++) - nuke(&dev->ep[i], -ECONNABORTED); -} - -static void udc_watchdog(unsigned long _dev) -{ - struct pxa2xx_udc *dev = (void *)_dev; - - local_irq_disable(); - if (dev->ep0state == EP0_STALL - && (UDCCS0 & UDCCS0_FST) == 0 - && (UDCCS0 & UDCCS0_SST) == 0) { - UDCCS0 = UDCCS0_FST|UDCCS0_FTF; - DBG(DBG_VERBOSE, "ep0 re-stall\n"); - start_watchdog(dev); - } - local_irq_enable(); -} - -static void handle_ep0 (struct pxa2xx_udc *dev) -{ - u32 udccs0 = UDCCS0; - struct pxa2xx_ep *ep = &dev->ep [0]; - struct pxa2xx_request *req; - union { - struct usb_ctrlrequest r; - u8 raw [8]; - u32 word [2]; - } u; - - if (list_empty(&ep->queue)) - req = NULL; - else - req = list_entry(ep->queue.next, struct pxa2xx_request, queue); - - /* clear stall status */ - if (udccs0 & UDCCS0_SST) { - nuke(ep, -EPIPE); - UDCCS0 = UDCCS0_SST; - del_timer(&dev->timer); - ep0_idle(dev); - } - - /* previous request unfinished? non-error iff back-to-back ... */ - if ((udccs0 & UDCCS0_SA) != 0 && dev->ep0state != EP0_IDLE) { - nuke(ep, 0); - del_timer(&dev->timer); - ep0_idle(dev); - } - - switch (dev->ep0state) { - case EP0_IDLE: - /* late-breaking status? */ - udccs0 = UDCCS0; - - /* start control request? */ - if (likely((udccs0 & (UDCCS0_OPR|UDCCS0_SA|UDCCS0_RNE)) - == (UDCCS0_OPR|UDCCS0_SA|UDCCS0_RNE))) { - int i; - - nuke (ep, -EPROTO); - - /* read SETUP packet */ - for (i = 0; i < 8; i++) { - if (unlikely(!(UDCCS0 & UDCCS0_RNE))) { -bad_setup: - DMSG("SETUP %d!\n", i); - goto stall; - } - u.raw [i] = (u8) UDDR0; - } - if (unlikely((UDCCS0 & UDCCS0_RNE) != 0)) - goto bad_setup; - -got_setup: - DBG(DBG_VERBOSE, "SETUP %02x.%02x v%04x i%04x l%04x\n", - u.r.bRequestType, u.r.bRequest, - le16_to_cpu(u.r.wValue), - le16_to_cpu(u.r.wIndex), - le16_to_cpu(u.r.wLength)); - - /* cope with automagic for some standard requests. */ - dev->req_std = (u.r.bRequestType & USB_TYPE_MASK) - == USB_TYPE_STANDARD; - dev->req_config = 0; - dev->req_pending = 1; - switch (u.r.bRequest) { - /* hardware restricts gadget drivers here! */ - case USB_REQ_SET_CONFIGURATION: - if (u.r.bRequestType == USB_RECIP_DEVICE) { - /* reflect hardware's automagic - * up to the gadget driver. - */ -config_change: - dev->req_config = 1; - clear_ep_state(dev); - /* if !has_cfr, there's no synch - * else use AREN (later) not SA|OPR - * USIR0_IR0 acts edge sensitive - */ - } - break; - /* ... and here, even more ... */ - case USB_REQ_SET_INTERFACE: - if (u.r.bRequestType == USB_RECIP_INTERFACE) { - /* udc hardware is broken by design: - * - altsetting may only be zero; - * - hw resets all interfaces' eps; - * - ep reset doesn't include halt(?). - */ - DMSG("broken set_interface (%d/%d)\n", - le16_to_cpu(u.r.wIndex), - le16_to_cpu(u.r.wValue)); - goto config_change; - } - break; - /* hardware was supposed to hide this */ - case USB_REQ_SET_ADDRESS: - if (u.r.bRequestType == USB_RECIP_DEVICE) { - ep0start(dev, 0, "address"); - return; - } - break; - } - - if (u.r.bRequestType & USB_DIR_IN) - dev->ep0state = EP0_IN_DATA_PHASE; - else - dev->ep0state = EP0_OUT_DATA_PHASE; - - i = dev->driver->setup(&dev->gadget, &u.r); - if (i < 0) { - /* hardware automagic preventing STALL... */ - if (dev->req_config) { - /* hardware sometimes neglects to tell - * tell us about config change events, - * so later ones may fail... - */ - WARN("config change %02x fail %d?\n", - u.r.bRequest, i); - return; - /* TODO experiment: if has_cfr, - * hardware didn't ACK; maybe we - * could actually STALL! - */ - } - DBG(DBG_VERBOSE, "protocol STALL, " - "%02x err %d\n", UDCCS0, i); -stall: - /* the watchdog timer helps deal with cases - * where udc seems to clear FST wrongly, and - * then NAKs instead of STALLing. - */ - ep0start(dev, UDCCS0_FST|UDCCS0_FTF, "stall"); - start_watchdog(dev); - dev->ep0state = EP0_STALL; - - /* deferred i/o == no response yet */ - } else if (dev->req_pending) { - if (likely(dev->ep0state == EP0_IN_DATA_PHASE - || dev->req_std || u.r.wLength)) - ep0start(dev, 0, "defer"); - else - ep0start(dev, UDCCS0_IPR, "defer/IPR"); - } - - /* expect at least one data or status stage irq */ - return; - - } else if (likely((udccs0 & (UDCCS0_OPR|UDCCS0_SA)) - == (UDCCS0_OPR|UDCCS0_SA))) { - unsigned i; - - /* pxa210/250 erratum 131 for B0/B1 says RNE lies. - * still observed on a pxa255 a0. - */ - DBG(DBG_VERBOSE, "e131\n"); - nuke(ep, -EPROTO); - - /* read SETUP data, but don't trust it too much */ - for (i = 0; i < 8; i++) - u.raw [i] = (u8) UDDR0; - if ((u.r.bRequestType & USB_RECIP_MASK) - > USB_RECIP_OTHER) - goto stall; - if (u.word [0] == 0 && u.word [1] == 0) - goto stall; - goto got_setup; - } else { - /* some random early IRQ: - * - we acked FST - * - IPR cleared - * - OPR got set, without SA (likely status stage) - */ - UDCCS0 = udccs0 & (UDCCS0_SA|UDCCS0_OPR); - } - break; - case EP0_IN_DATA_PHASE: /* GET_DESCRIPTOR etc */ - if (udccs0 & UDCCS0_OPR) { - UDCCS0 = UDCCS0_OPR|UDCCS0_FTF; - DBG(DBG_VERBOSE, "ep0in premature status\n"); - if (req) - done(ep, req, 0); - ep0_idle(dev); - } else /* irq was IPR clearing */ { - if (req) { - /* this IN packet might finish the request */ - (void) write_ep0_fifo(ep, req); - } /* else IN token before response was written */ - } - break; - case EP0_OUT_DATA_PHASE: /* SET_DESCRIPTOR etc */ - if (udccs0 & UDCCS0_OPR) { - if (req) { - /* this OUT packet might finish the request */ - if (read_ep0_fifo(ep, req)) - done(ep, req, 0); - /* else more OUT packets expected */ - } /* else OUT token before read was issued */ - } else /* irq was IPR clearing */ { - DBG(DBG_VERBOSE, "ep0out premature status\n"); - if (req) - done(ep, req, 0); - ep0_idle(dev); - } - break; - case EP0_END_XFER: - if (req) - done(ep, req, 0); - /* ack control-IN status (maybe in-zlp was skipped) - * also appears after some config change events. - */ - if (udccs0 & UDCCS0_OPR) - UDCCS0 = UDCCS0_OPR; - ep0_idle(dev); - break; - case EP0_STALL: - UDCCS0 = UDCCS0_FST; - break; - } - USIR0 = USIR0_IR0; -} - -static void handle_ep(struct pxa2xx_ep *ep) -{ - struct pxa2xx_request *req; - int is_in = ep->bEndpointAddress & USB_DIR_IN; - int completed; - u32 udccs, tmp; - - do { - completed = 0; - if (likely (!list_empty(&ep->queue))) - req = list_entry(ep->queue.next, - struct pxa2xx_request, queue); - else - req = NULL; - - // TODO check FST handling - - udccs = *ep->reg_udccs; - if (unlikely(is_in)) { /* irq from TPC, SST, or (ISO) TUR */ - tmp = UDCCS_BI_TUR; - if (likely(ep->bmAttributes == USB_ENDPOINT_XFER_BULK)) - tmp |= UDCCS_BI_SST; - tmp &= udccs; - if (likely (tmp)) - *ep->reg_udccs = tmp; - if (req && likely ((udccs & UDCCS_BI_TFS) != 0)) - completed = write_fifo(ep, req); - - } else { /* irq from RPC (or for ISO, ROF) */ - if (likely(ep->bmAttributes == USB_ENDPOINT_XFER_BULK)) - tmp = UDCCS_BO_SST | UDCCS_BO_DME; - else - tmp = UDCCS_IO_ROF | UDCCS_IO_DME; - tmp &= udccs; - if (likely(tmp)) - *ep->reg_udccs = tmp; - - /* fifos can hold packets, ready for reading... */ - if (likely(req)) { - completed = read_fifo(ep, req); - } else - pio_irq_disable (ep->bEndpointAddress); - } - ep->pio_irqs++; - } while (completed); -} - -/* - * pxa2xx_udc_irq - interrupt handler - * - * avoid delays in ep0 processing. the control handshaking isn't always - * under software control (pxa250c0 and the pxa255 are better), and delays - * could cause usb protocol errors. - */ -static irqreturn_t -pxa2xx_udc_irq(int irq, void *_dev) -{ - struct pxa2xx_udc *dev = _dev; - int handled; - - dev->stats.irqs++; - do { - u32 udccr = UDCCR; - - handled = 0; - - /* SUSpend Interrupt Request */ - if (unlikely(udccr & UDCCR_SUSIR)) { - udc_ack_int_UDCCR(UDCCR_SUSIR); - handled = 1; - DBG(DBG_VERBOSE, "USB suspend%s\n", is_vbus_present() - ? "" : "+disconnect"); - - if (!is_vbus_present()) - stop_activity(dev, dev->driver); - else if (dev->gadget.speed != USB_SPEED_UNKNOWN - && dev->driver - && dev->driver->suspend) - dev->driver->suspend(&dev->gadget); - ep0_idle (dev); - } - - /* RESume Interrupt Request */ - if (unlikely(udccr & UDCCR_RESIR)) { - udc_ack_int_UDCCR(UDCCR_RESIR); - handled = 1; - DBG(DBG_VERBOSE, "USB resume\n"); - - if (dev->gadget.speed != USB_SPEED_UNKNOWN - && dev->driver - && dev->driver->resume - && is_vbus_present()) - dev->driver->resume(&dev->gadget); - } - - /* ReSeT Interrupt Request - USB reset */ - if (unlikely(udccr & UDCCR_RSTIR)) { - udc_ack_int_UDCCR(UDCCR_RSTIR); - handled = 1; - - if ((UDCCR & UDCCR_UDA) == 0) { - DBG(DBG_VERBOSE, "USB reset start\n"); - - /* reset driver and endpoints, - * in case that's not yet done - */ - stop_activity (dev, dev->driver); - - } else { - DBG(DBG_VERBOSE, "USB reset end\n"); - dev->gadget.speed = USB_SPEED_FULL; - memset(&dev->stats, 0, sizeof dev->stats); - /* driver and endpoints are still reset */ - } - - } else { - u32 usir0 = USIR0 & ~UICR0; - u32 usir1 = USIR1 & ~UICR1; - int i; - - if (unlikely (!usir0 && !usir1)) - continue; - - DBG(DBG_VERY_NOISY, "irq %02x.%02x\n", usir1, usir0); - - /* control traffic */ - if (usir0 & USIR0_IR0) { - dev->ep[0].pio_irqs++; - handle_ep0(dev); - handled = 1; - } - - /* endpoint data transfers */ - for (i = 0; i < 8; i++) { - u32 tmp = 1 << i; - - if (i && (usir0 & tmp)) { - handle_ep(&dev->ep[i]); - USIR0 |= tmp; - handled = 1; - } - if (usir1 & tmp) { - handle_ep(&dev->ep[i+8]); - USIR1 |= tmp; - handled = 1; - } - } - } - - /* we could also ask for 1 msec SOF (SIR) interrupts */ - - } while (handled); - return IRQ_HANDLED; -} - -/*-------------------------------------------------------------------------*/ - -static void nop_release (struct device *dev) -{ - DMSG("%s %s\n", __func__, dev->bus_id); -} - -/* this uses load-time allocation and initialization (instead of - * doing it at run-time) to save code, eliminate fault paths, and - * be more obviously correct. - */ -static struct pxa2xx_udc memory = { - .gadget = { - .ops = &pxa2xx_udc_ops, - .ep0 = &memory.ep[0].ep, - .name = driver_name, - .dev = { - .bus_id = "gadget", - .release = nop_release, - }, - }, - - /* control endpoint */ - .ep[0] = { - .ep = { - .name = ep0name, - .ops = &pxa2xx_ep_ops, - .maxpacket = EP0_FIFO_SIZE, - }, - .dev = &memory, - .reg_udccs = &UDCCS0, - .reg_uddr = &UDDR0, - }, - - /* first group of endpoints */ - .ep[1] = { - .ep = { - .name = "ep1in-bulk", - .ops = &pxa2xx_ep_ops, - .maxpacket = BULK_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = BULK_FIFO_SIZE, - .bEndpointAddress = USB_DIR_IN | 1, - .bmAttributes = USB_ENDPOINT_XFER_BULK, - .reg_udccs = &UDCCS1, - .reg_uddr = &UDDR1, - }, - .ep[2] = { - .ep = { - .name = "ep2out-bulk", - .ops = &pxa2xx_ep_ops, - .maxpacket = BULK_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = BULK_FIFO_SIZE, - .bEndpointAddress = 2, - .bmAttributes = USB_ENDPOINT_XFER_BULK, - .reg_udccs = &UDCCS2, - .reg_ubcr = &UBCR2, - .reg_uddr = &UDDR2, - }, -#ifndef CONFIG_USB_PXA2XX_SMALL - .ep[3] = { - .ep = { - .name = "ep3in-iso", - .ops = &pxa2xx_ep_ops, - .maxpacket = ISO_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = ISO_FIFO_SIZE, - .bEndpointAddress = USB_DIR_IN | 3, - .bmAttributes = USB_ENDPOINT_XFER_ISOC, - .reg_udccs = &UDCCS3, - .reg_uddr = &UDDR3, - }, - .ep[4] = { - .ep = { - .name = "ep4out-iso", - .ops = &pxa2xx_ep_ops, - .maxpacket = ISO_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = ISO_FIFO_SIZE, - .bEndpointAddress = 4, - .bmAttributes = USB_ENDPOINT_XFER_ISOC, - .reg_udccs = &UDCCS4, - .reg_ubcr = &UBCR4, - .reg_uddr = &UDDR4, - }, - .ep[5] = { - .ep = { - .name = "ep5in-int", - .ops = &pxa2xx_ep_ops, - .maxpacket = INT_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = INT_FIFO_SIZE, - .bEndpointAddress = USB_DIR_IN | 5, - .bmAttributes = USB_ENDPOINT_XFER_INT, - .reg_udccs = &UDCCS5, - .reg_uddr = &UDDR5, - }, - - /* second group of endpoints */ - .ep[6] = { - .ep = { - .name = "ep6in-bulk", - .ops = &pxa2xx_ep_ops, - .maxpacket = BULK_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = BULK_FIFO_SIZE, - .bEndpointAddress = USB_DIR_IN | 6, - .bmAttributes = USB_ENDPOINT_XFER_BULK, - .reg_udccs = &UDCCS6, - .reg_uddr = &UDDR6, - }, - .ep[7] = { - .ep = { - .name = "ep7out-bulk", - .ops = &pxa2xx_ep_ops, - .maxpacket = BULK_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = BULK_FIFO_SIZE, - .bEndpointAddress = 7, - .bmAttributes = USB_ENDPOINT_XFER_BULK, - .reg_udccs = &UDCCS7, - .reg_ubcr = &UBCR7, - .reg_uddr = &UDDR7, - }, - .ep[8] = { - .ep = { - .name = "ep8in-iso", - .ops = &pxa2xx_ep_ops, - .maxpacket = ISO_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = ISO_FIFO_SIZE, - .bEndpointAddress = USB_DIR_IN | 8, - .bmAttributes = USB_ENDPOINT_XFER_ISOC, - .reg_udccs = &UDCCS8, - .reg_uddr = &UDDR8, - }, - .ep[9] = { - .ep = { - .name = "ep9out-iso", - .ops = &pxa2xx_ep_ops, - .maxpacket = ISO_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = ISO_FIFO_SIZE, - .bEndpointAddress = 9, - .bmAttributes = USB_ENDPOINT_XFER_ISOC, - .reg_udccs = &UDCCS9, - .reg_ubcr = &UBCR9, - .reg_uddr = &UDDR9, - }, - .ep[10] = { - .ep = { - .name = "ep10in-int", - .ops = &pxa2xx_ep_ops, - .maxpacket = INT_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = INT_FIFO_SIZE, - .bEndpointAddress = USB_DIR_IN | 10, - .bmAttributes = USB_ENDPOINT_XFER_INT, - .reg_udccs = &UDCCS10, - .reg_uddr = &UDDR10, - }, - - /* third group of endpoints */ - .ep[11] = { - .ep = { - .name = "ep11in-bulk", - .ops = &pxa2xx_ep_ops, - .maxpacket = BULK_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = BULK_FIFO_SIZE, - .bEndpointAddress = USB_DIR_IN | 11, - .bmAttributes = USB_ENDPOINT_XFER_BULK, - .reg_udccs = &UDCCS11, - .reg_uddr = &UDDR11, - }, - .ep[12] = { - .ep = { - .name = "ep12out-bulk", - .ops = &pxa2xx_ep_ops, - .maxpacket = BULK_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = BULK_FIFO_SIZE, - .bEndpointAddress = 12, - .bmAttributes = USB_ENDPOINT_XFER_BULK, - .reg_udccs = &UDCCS12, - .reg_ubcr = &UBCR12, - .reg_uddr = &UDDR12, - }, - .ep[13] = { - .ep = { - .name = "ep13in-iso", - .ops = &pxa2xx_ep_ops, - .maxpacket = ISO_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = ISO_FIFO_SIZE, - .bEndpointAddress = USB_DIR_IN | 13, - .bmAttributes = USB_ENDPOINT_XFER_ISOC, - .reg_udccs = &UDCCS13, - .reg_uddr = &UDDR13, - }, - .ep[14] = { - .ep = { - .name = "ep14out-iso", - .ops = &pxa2xx_ep_ops, - .maxpacket = ISO_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = ISO_FIFO_SIZE, - .bEndpointAddress = 14, - .bmAttributes = USB_ENDPOINT_XFER_ISOC, - .reg_udccs = &UDCCS14, - .reg_ubcr = &UBCR14, - .reg_uddr = &UDDR14, - }, - .ep[15] = { - .ep = { - .name = "ep15in-int", - .ops = &pxa2xx_ep_ops, - .maxpacket = INT_FIFO_SIZE, - }, - .dev = &memory, - .fifo_size = INT_FIFO_SIZE, - .bEndpointAddress = USB_DIR_IN | 15, - .bmAttributes = USB_ENDPOINT_XFER_INT, - .reg_udccs = &UDCCS15, - .reg_uddr = &UDDR15, - }, -#endif /* !CONFIG_USB_PXA2XX_SMALL */ -}; - -#define CP15R0_VENDOR_MASK 0xffffe000 - -#if defined(CONFIG_ARCH_PXA) -#define CP15R0_XSCALE_VALUE 0x69052000 /* intel/arm/xscale */ - -#elif defined(CONFIG_ARCH_IXP4XX) -#define CP15R0_XSCALE_VALUE 0x69054000 /* intel/arm/ixp4xx */ - -#endif - -#define CP15R0_PROD_MASK 0x000003f0 -#define PXA25x 0x00000100 /* and PXA26x */ -#define PXA210 0x00000120 - -#define CP15R0_REV_MASK 0x0000000f - -#define CP15R0_PRODREV_MASK (CP15R0_PROD_MASK | CP15R0_REV_MASK) - -#define PXA255_A0 0x00000106 /* or PXA260_B1 */ -#define PXA250_C0 0x00000105 /* or PXA26x_B0 */ -#define PXA250_B2 0x00000104 -#define PXA250_B1 0x00000103 /* or PXA260_A0 */ -#define PXA250_B0 0x00000102 -#define PXA250_A1 0x00000101 -#define PXA250_A0 0x00000100 - -#define PXA210_C0 0x00000125 -#define PXA210_B2 0x00000124 -#define PXA210_B1 0x00000123 -#define PXA210_B0 0x00000122 -#define IXP425_A0 0x000001c1 -#define IXP425_B0 0x000001f1 -#define IXP465_AD 0x00000200 - -/* - * probe - binds to the platform device - */ -static int __init pxa2xx_udc_probe(struct platform_device *pdev) -{ - struct pxa2xx_udc *dev = &memory; - int retval, vbus_irq, irq; - u32 chiprev; - - /* insist on Intel/ARM/XScale */ - asm("mrc%? p15, 0, %0, c0, c0" : "=r" (chiprev)); - if ((chiprev & CP15R0_VENDOR_MASK) != CP15R0_XSCALE_VALUE) { - pr_err("%s: not XScale!\n", driver_name); - return -ENODEV; - } - - /* trigger chiprev-specific logic */ - switch (chiprev & CP15R0_PRODREV_MASK) { -#if defined(CONFIG_ARCH_PXA) - case PXA255_A0: - dev->has_cfr = 1; - break; - case PXA250_A0: - case PXA250_A1: - /* A0/A1 "not released"; ep 13, 15 unusable */ - /* fall through */ - case PXA250_B2: case PXA210_B2: - case PXA250_B1: case PXA210_B1: - case PXA250_B0: case PXA210_B0: - /* OUT-DMA is broken ... */ - /* fall through */ - case PXA250_C0: case PXA210_C0: - break; -#elif defined(CONFIG_ARCH_IXP4XX) - case IXP425_A0: - case IXP425_B0: - case IXP465_AD: - dev->has_cfr = 1; - break; -#endif - default: - pr_err("%s: unrecognized processor: %08x\n", - driver_name, chiprev); - /* iop3xx, ixp4xx, ... */ - return -ENODEV; - } - - irq = platform_get_irq(pdev, 0); - if (irq < 0) - return -ENODEV; - - dev->clk = clk_get(&pdev->dev, "UDCCLK"); - if (IS_ERR(dev->clk)) { - retval = PTR_ERR(dev->clk); - goto err_clk; - } - - pr_debug("%s: IRQ %d%s%s\n", driver_name, irq, - dev->has_cfr ? "" : " (!cfr)", - SIZE_STR "(pio)" - ); - - /* other non-static parts of init */ - dev->dev = &pdev->dev; - dev->mach = pdev->dev.platform_data; - - if (dev->mach->gpio_vbus) { - if ((retval = gpio_request(dev->mach->gpio_vbus, - "pxa2xx_udc GPIO VBUS"))) { - dev_dbg(&pdev->dev, - "can't get vbus gpio %d, err: %d\n", - dev->mach->gpio_vbus, retval); - goto err_gpio_vbus; - } - gpio_direction_input(dev->mach->gpio_vbus); - vbus_irq = gpio_to_irq(dev->mach->gpio_vbus); - } else - vbus_irq = 0; - - if (dev->mach->gpio_pullup) { - if ((retval = gpio_request(dev->mach->gpio_pullup, - "pca2xx_udc GPIO PULLUP"))) { - dev_dbg(&pdev->dev, - "can't get pullup gpio %d, err: %d\n", - dev->mach->gpio_pullup, retval); - goto err_gpio_pullup; - } - gpio_direction_output(dev->mach->gpio_pullup, 0); - } - - init_timer(&dev->timer); - dev->timer.function = udc_watchdog; - dev->timer.data = (unsigned long) dev; - - device_initialize(&dev->gadget.dev); - dev->gadget.dev.parent = &pdev->dev; - dev->gadget.dev.dma_mask = pdev->dev.dma_mask; - - the_controller = dev; - platform_set_drvdata(pdev, dev); - - udc_disable(dev); - udc_reinit(dev); - - dev->vbus = is_vbus_present(); - - /* irq setup after old hardware state is cleaned up */ - retval = request_irq(irq, pxa2xx_udc_irq, - IRQF_DISABLED, driver_name, dev); - if (retval != 0) { - pr_err("%s: can't get irq %d, err %d\n", - driver_name, irq, retval); - goto err_irq1; - } - dev->got_irq = 1; - -#ifdef CONFIG_ARCH_LUBBOCK - if (machine_is_lubbock()) { - retval = request_irq(LUBBOCK_USB_DISC_IRQ, - lubbock_vbus_irq, - IRQF_DISABLED | IRQF_SAMPLE_RANDOM, - driver_name, dev); - if (retval != 0) { - pr_err("%s: can't get irq %i, err %d\n", - driver_name, LUBBOCK_USB_DISC_IRQ, retval); -lubbock_fail0: - goto err_irq_lub; - } - retval = request_irq(LUBBOCK_USB_IRQ, - lubbock_vbus_irq, - IRQF_DISABLED | IRQF_SAMPLE_RANDOM, - driver_name, dev); - if (retval != 0) { - pr_err("%s: can't get irq %i, err %d\n", - driver_name, LUBBOCK_USB_IRQ, retval); - free_irq(LUBBOCK_USB_DISC_IRQ, dev); - goto lubbock_fail0; - } - } else -#endif - if (vbus_irq) { - retval = request_irq(vbus_irq, udc_vbus_irq, - IRQF_DISABLED | IRQF_SAMPLE_RANDOM | - IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, - driver_name, dev); - if (retval != 0) { - pr_err("%s: can't get irq %i, err %d\n", - driver_name, vbus_irq, retval); - goto err_vbus_irq; - } - } - create_debug_files(dev); - - return 0; - - err_vbus_irq: -#ifdef CONFIG_ARCH_LUBBOCK - free_irq(LUBBOCK_USB_DISC_IRQ, dev); - err_irq_lub: -#endif - free_irq(irq, dev); - err_irq1: - if (dev->mach->gpio_pullup) - gpio_free(dev->mach->gpio_pullup); - err_gpio_pullup: - if (dev->mach->gpio_vbus) - gpio_free(dev->mach->gpio_vbus); - err_gpio_vbus: - clk_put(dev->clk); - err_clk: - return retval; -} - -static void pxa2xx_udc_shutdown(struct platform_device *_dev) -{ - pullup_off(); -} - -static int __exit pxa2xx_udc_remove(struct platform_device *pdev) -{ - struct pxa2xx_udc *dev = platform_get_drvdata(pdev); - - if (dev->driver) - return -EBUSY; - - dev->pullup = 0; - pullup(dev); - - remove_debug_files(dev); - - if (dev->got_irq) { - free_irq(platform_get_irq(pdev, 0), dev); - dev->got_irq = 0; - } -#ifdef CONFIG_ARCH_LUBBOCK - if (machine_is_lubbock()) { - free_irq(LUBBOCK_USB_DISC_IRQ, dev); - free_irq(LUBBOCK_USB_IRQ, dev); - } -#endif - if (dev->mach->gpio_vbus) { - free_irq(gpio_to_irq(dev->mach->gpio_vbus), dev); - gpio_free(dev->mach->gpio_vbus); - } - if (dev->mach->gpio_pullup) - gpio_free(dev->mach->gpio_pullup); - - clk_put(dev->clk); - - platform_set_drvdata(pdev, NULL); - the_controller = NULL; - return 0; -} - -/*-------------------------------------------------------------------------*/ - -#ifdef CONFIG_PM - -/* USB suspend (controlled by the host) and system suspend (controlled - * by the PXA) don't necessarily work well together. If USB is active, - * the 48 MHz clock is required; so the system can't enter 33 MHz idle - * mode, or any deeper PM saving state. - * - * For now, we punt and forcibly disconnect from the USB host when PXA - * enters any suspend state. While we're disconnected, we always disable - * the 48MHz USB clock ... allowing PXA sleep and/or 33 MHz idle states. - * Boards without software pullup control shouldn't use those states. - * VBUS IRQs should probably be ignored so that the PXA device just acts - * "dead" to USB hosts until system resume. - */ -static int pxa2xx_udc_suspend(struct platform_device *dev, pm_message_t state) -{ - struct pxa2xx_udc *udc = platform_get_drvdata(dev); - unsigned long flags; - - if (!udc->mach->gpio_pullup && !udc->mach->udc_command) - WARN("USB host won't detect disconnect!\n"); - udc->suspended = 1; - - local_irq_save(flags); - pullup(udc); - local_irq_restore(flags); - - return 0; -} - -static int pxa2xx_udc_resume(struct platform_device *dev) -{ - struct pxa2xx_udc *udc = platform_get_drvdata(dev); - unsigned long flags; - - udc->suspended = 0; - local_irq_save(flags); - pullup(udc); - local_irq_restore(flags); - - return 0; -} - -#else -#define pxa2xx_udc_suspend NULL -#define pxa2xx_udc_resume NULL -#endif - -/*-------------------------------------------------------------------------*/ - -static struct platform_driver udc_driver = { - .shutdown = pxa2xx_udc_shutdown, - .remove = __exit_p(pxa2xx_udc_remove), - .suspend = pxa2xx_udc_suspend, - .resume = pxa2xx_udc_resume, - .driver = { - .owner = THIS_MODULE, - .name = "pxa2xx-udc", - }, -}; - -static int __init udc_init(void) -{ - pr_info("%s: version %s\n", driver_name, DRIVER_VERSION); - return platform_driver_probe(&udc_driver, pxa2xx_udc_probe); -} -module_init(udc_init); - -static void __exit udc_exit(void) -{ - platform_driver_unregister(&udc_driver); -} -module_exit(udc_exit); - -MODULE_DESCRIPTION(DRIVER_DESC); -MODULE_AUTHOR("Frank Becker, Robert Schwebel, David Brownell"); -MODULE_LICENSE("GPL"); -MODULE_ALIAS("platform:pxa2xx-udc"); diff --git a/drivers/usb/gadget/pxa2xx_udc.h b/drivers/usb/gadget/pxa2xx_udc.h deleted file mode 100644 index e2c19e88c87..00000000000 --- a/drivers/usb/gadget/pxa2xx_udc.h +++ /dev/null @@ -1,267 +0,0 @@ -/* - * linux/drivers/usb/gadget/pxa2xx_udc.h - * Intel PXA2xx on-chip full speed USB device controller - * - * Copyright (C) 2003 Robert Schwebel , Pengutronix - * Copyright (C) 2003 David Brownell - * - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __LINUX_USB_GADGET_PXA2XX_H -#define __LINUX_USB_GADGET_PXA2XX_H - -#include - -/*-------------------------------------------------------------------------*/ - -/* pxa2xx has this (move to include/asm-arm/arch-pxa/pxa-regs.h) */ -#define UFNRH_SIR (1 << 7) /* SOF interrupt request */ -#define UFNRH_SIM (1 << 6) /* SOF interrupt mask */ -#define UFNRH_IPE14 (1 << 5) /* ISO packet error, ep14 */ -#define UFNRH_IPE9 (1 << 4) /* ISO packet error, ep9 */ -#define UFNRH_IPE4 (1 << 3) /* ISO packet error, ep4 */ - -/* pxa255 has this (move to include/asm-arm/arch-pxa/pxa-regs.h) */ -#define UDCCFR UDC_RES2 /* UDC Control Function Register */ -#define UDCCFR_AREN (1 << 7) /* ACK response enable (now) */ -#define UDCCFR_ACM (1 << 2) /* ACK control mode (wait for AREN) */ - -/* latest pxa255 errata define new "must be one" bits in UDCCFR */ -#define UDCCFR_MB1 (0xff & ~(UDCCFR_AREN|UDCCFR_ACM)) - -/*-------------------------------------------------------------------------*/ - -struct pxa2xx_udc; - -struct pxa2xx_ep { - struct usb_ep ep; - struct pxa2xx_udc *dev; - - const struct usb_endpoint_descriptor *desc; - struct list_head queue; - unsigned long pio_irqs; - - unsigned short fifo_size; - u8 bEndpointAddress; - u8 bmAttributes; - - unsigned stopped : 1; - unsigned dma_fixup : 1; - - /* UDCCS = UDC Control/Status for this EP - * UBCR = UDC Byte Count Remaining (contents of OUT fifo) - * UDDR = UDC Endpoint Data Register (the fifo) - * DRCM = DMA Request Channel Map - */ - volatile u32 *reg_udccs; - volatile u32 *reg_ubcr; - volatile u32 *reg_uddr; -}; - -struct pxa2xx_request { - struct usb_request req; - struct list_head queue; -}; - -enum ep0_state { - EP0_IDLE, - EP0_IN_DATA_PHASE, - EP0_OUT_DATA_PHASE, - EP0_END_XFER, - EP0_STALL, -}; - -#define EP0_FIFO_SIZE ((unsigned)16) -#define BULK_FIFO_SIZE ((unsigned)64) -#define ISO_FIFO_SIZE ((unsigned)256) -#define INT_FIFO_SIZE ((unsigned)8) - -struct udc_stats { - struct ep0stats { - unsigned long ops; - unsigned long bytes; - } read, write; - unsigned long irqs; -}; - -#ifdef CONFIG_USB_PXA2XX_SMALL -/* when memory's tight, SMALL config saves code+data. */ -#define PXA_UDC_NUM_ENDPOINTS 3 -#endif - -#ifndef PXA_UDC_NUM_ENDPOINTS -#define PXA_UDC_NUM_ENDPOINTS 16 -#endif - -struct pxa2xx_udc { - struct usb_gadget gadget; - struct usb_gadget_driver *driver; - - enum ep0_state ep0state; - struct udc_stats stats; - unsigned got_irq : 1, - vbus : 1, - pullup : 1, - has_cfr : 1, - req_pending : 1, - req_std : 1, - req_config : 1, - suspended : 1, - active : 1; - -#define start_watchdog(dev) mod_timer(&dev->timer, jiffies + (HZ/200)) - struct timer_list timer; - - struct device *dev; - struct clk *clk; - struct pxa2xx_udc_mach_info *mach; - u64 dma_mask; - struct pxa2xx_ep ep [PXA_UDC_NUM_ENDPOINTS]; - -#ifdef CONFIG_USB_GADGET_DEBUG_FS - struct dentry *debugfs_udc; -#endif -}; - -/*-------------------------------------------------------------------------*/ - -#ifdef CONFIG_ARCH_LUBBOCK -#include -/* lubbock can also report usb connect/disconnect irqs */ -#endif - -static struct pxa2xx_udc *the_controller; - -/*-------------------------------------------------------------------------*/ - -/* - * Debugging support vanishes in non-debug builds. DBG_NORMAL should be - * mostly silent during normal use/testing, with no timing side-effects. - */ -#define DBG_NORMAL 1 /* error paths, device state transitions */ -#define DBG_VERBOSE 2 /* add some success path trace info */ -#define DBG_NOISY 3 /* ... even more: request level */ -#define DBG_VERY_NOISY 4 /* ... even more: packet level */ - -#define DMSG(stuff...) pr_debug("udc: " stuff) - -#ifdef DEBUG - -static int is_vbus_present(void); - -static const char *state_name[] = { - "EP0_IDLE", - "EP0_IN_DATA_PHASE", "EP0_OUT_DATA_PHASE", - "EP0_END_XFER", "EP0_STALL" -}; - -#ifdef VERBOSE_DEBUG -# define UDC_DEBUG DBG_VERBOSE -#else -# define UDC_DEBUG DBG_NORMAL -#endif - -static void __maybe_unused -dump_udccr(const char *label) -{ - u32 udccr = UDCCR; - DMSG("%s %02X =%s%s%s%s%s%s%s%s\n", - label, udccr, - (udccr & UDCCR_REM) ? " rem" : "", - (udccr & UDCCR_RSTIR) ? " rstir" : "", - (udccr & UDCCR_SRM) ? " srm" : "", - (udccr & UDCCR_SUSIR) ? " susir" : "", - (udccr & UDCCR_RESIR) ? " resir" : "", - (udccr & UDCCR_RSM) ? " rsm" : "", - (udccr & UDCCR_UDA) ? " uda" : "", - (udccr & UDCCR_UDE) ? " ude" : ""); -} - -static void __maybe_unused -dump_udccs0(const char *label) -{ - u32 udccs0 = UDCCS0; - - DMSG("%s %s %02X =%s%s%s%s%s%s%s%s\n", - label, state_name[the_controller->ep0state], udccs0, - (udccs0 & UDCCS0_SA) ? " sa" : "", - (udccs0 & UDCCS0_RNE) ? " rne" : "", - (udccs0 & UDCCS0_FST) ? " fst" : "", - (udccs0 & UDCCS0_SST) ? " sst" : "", - (udccs0 & UDCCS0_DRWF) ? " dwrf" : "", - (udccs0 & UDCCS0_FTF) ? " ftf" : "", - (udccs0 & UDCCS0_IPR) ? " ipr" : "", - (udccs0 & UDCCS0_OPR) ? " opr" : ""); -} - -static void __maybe_unused -dump_state(struct pxa2xx_udc *dev) -{ - u32 tmp; - unsigned i; - - DMSG("%s %s, uicr %02X.%02X, usir %02X.%02x, ufnr %02X.%02X\n", - is_vbus_present() ? "host " : "disconnected", - state_name[dev->ep0state], - UICR1, UICR0, USIR1, USIR0, UFNRH, UFNRL); - dump_udccr("udccr"); - if (dev->has_cfr) { - tmp = UDCCFR; - DMSG("udccfr %02X =%s%s\n", tmp, - (tmp & UDCCFR_AREN) ? " aren" : "", - (tmp & UDCCFR_ACM) ? " acm" : ""); - } - - if (!dev->driver) { - DMSG("no gadget driver bound\n"); - return; - } else - DMSG("ep0 driver '%s'\n", dev->driver->driver.name); - - if (!is_vbus_present()) - return; - - dump_udccs0 ("udccs0"); - DMSG("ep0 IN %lu/%lu, OUT %lu/%lu\n", - dev->stats.write.bytes, dev->stats.write.ops, - dev->stats.read.bytes, dev->stats.read.ops); - - for (i = 1; i < PXA_UDC_NUM_ENDPOINTS; i++) { - if (dev->ep [i].desc == NULL) - continue; - DMSG ("udccs%d = %02x\n", i, *dev->ep->reg_udccs); - } -} - -#else - -#define dump_udccr(x) do{}while(0) -#define dump_udccs0(x) do{}while(0) -#define dump_state(x) do{}while(0) - -#define UDC_DEBUG ((unsigned)0) - -#endif - -#define DBG(lvl, stuff...) do{if ((lvl) <= UDC_DEBUG) DMSG(stuff);}while(0) - -#define ERR(stuff...) pr_err("udc: " stuff) -#define WARN(stuff...) pr_warning("udc: " stuff) -#define INFO(stuff...) pr_info("udc: " stuff) - - -#endif /* __LINUX_USB_GADGET_PXA2XX_H */ -- cgit v1.2.3 From 613526677a74c2b3d1b1696ea7334b2cf35155b3 Mon Sep 17 00:00:00 2001 From: sedji gaouaou Date: Thu, 10 Jul 2008 10:15:35 +0100 Subject: [ARM] 5130/4: Support for the at91sam9g20 Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC. AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. We created a new board for this device but based the chip support directly on 9260 files with little updates. Here is the chip page on Atmel wabsite: http://atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Sedji Gaouaou Signed-off-by: Justin Waters Acked-by: Andrew Victor Signed-off-by: Russell King --- drivers/usb/gadget/at91_udc.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/usb/gadget') diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c index 274c60a970c..b6b2a0a5ba3 100644 --- a/drivers/usb/gadget/at91_udc.c +++ b/drivers/usb/gadget/at91_udc.c @@ -888,7 +888,7 @@ static void pullup(struct at91_udc *udc, int is_on) at91_udp_write(udc, AT91_UDP_TXVC, 0); if (cpu_is_at91rm9200()) gpio_set_value(udc->board.pullup_pin, active); - else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { + else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC); txvc |= AT91_UDP_TXVC_PUON; @@ -906,7 +906,7 @@ static void pullup(struct at91_udc *udc, int is_on) at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS); if (cpu_is_at91rm9200()) gpio_set_value(udc->board.pullup_pin, !active); - else if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) { + else if (cpu_is_at91sam9260() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) { u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC); txvc &= ~AT91_UDP_TXVC_PUON; -- cgit v1.2.3