From 5616c23ad9cd3c50af674d408fef7b90abeee81c Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Tue, 22 Jul 2008 15:32:38 -0400 Subject: x86: doc: move x86-generic documentation from Doc/x86/i386 The boot protocol, USB legacy support, and zero-page documentation is common to the x86 platform, not i386-specific. Signed-off-by: H. Peter Anvin --- Documentation/x86/boot.txt | 900 ++++++++++++++++++++++++++ Documentation/x86/i386/boot.txt | 900 -------------------------- Documentation/x86/i386/usb-legacy-support.txt | 44 -- Documentation/x86/i386/zero-page.txt | 31 - Documentation/x86/usb-legacy-support.txt | 44 ++ Documentation/x86/zero-page.txt | 31 + 6 files changed, 975 insertions(+), 975 deletions(-) create mode 100644 Documentation/x86/boot.txt delete mode 100644 Documentation/x86/i386/boot.txt delete mode 100644 Documentation/x86/i386/usb-legacy-support.txt delete mode 100644 Documentation/x86/i386/zero-page.txt create mode 100644 Documentation/x86/usb-legacy-support.txt create mode 100644 Documentation/x86/zero-page.txt (limited to 'Documentation') diff --git a/Documentation/x86/boot.txt b/Documentation/x86/boot.txt new file mode 100644 index 00000000000..147bfe511cd --- /dev/null +++ b/Documentation/x86/boot.txt @@ -0,0 +1,900 @@ + THE LINUX/x86 BOOT PROTOCOL + --------------------------- + +On the x86 platform, the Linux kernel uses a rather complicated boot +convention. This has evolved partially due to historical aspects, as +well as the desire in the early days to have the kernel itself be a +bootable image, the complicated PC memory model and due to changed +expectations in the PC industry caused by the effective demise of +real-mode DOS as a mainstream operating system. + +Currently, the following versions of the Linux/x86 boot protocol exist. + +Old kernels: zImage/Image support only. Some very early kernels + may not even support a command line. + +Protocol 2.00: (Kernel 1.3.73) Added bzImage and initrd support, as + well as a formalized way to communicate between the + boot loader and the kernel. setup.S made relocatable, + although the traditional setup area still assumed + writable. + +Protocol 2.01: (Kernel 1.3.76) Added a heap overrun warning. + +Protocol 2.02: (Kernel 2.4.0-test3-pre3) New command line protocol. + Lower the conventional memory ceiling. No overwrite + of the traditional setup area, thus making booting + safe for systems which use the EBDA from SMM or 32-bit + BIOS entry points. zImage deprecated but still + supported. + +Protocol 2.03: (Kernel 2.4.18-pre1) Explicitly makes the highest possible + initrd address available to the bootloader. + +Protocol 2.04: (Kernel 2.6.14) Extend the syssize field to four bytes. + +Protocol 2.05: (Kernel 2.6.20) Make protected mode kernel relocatable. + Introduce relocatable_kernel and kernel_alignment fields. + +Protocol 2.06: (Kernel 2.6.22) Added a field that contains the size of + the boot command line. + +Protocol 2.07: (Kernel 2.6.24) Added paravirtualised boot protocol. + Introduced hardware_subarch and hardware_subarch_data + and KEEP_SEGMENTS flag in load_flags. + +Protocol 2.08: (Kernel 2.6.26) Added crc32 checksum and ELF format + payload. Introduced payload_offset and payload length + fields to aid in locating the payload. + +Protocol 2.09: (Kernel 2.6.26) Added a field of 64-bit physical + pointer to single linked list of struct setup_data. + +**** MEMORY LAYOUT + +The traditional memory map for the kernel loader, used for Image or +zImage kernels, typically looks like: + + | | +0A0000 +------------------------+ + | Reserved for BIOS | Do not use. Reserved for BIOS EBDA. +09A000 +------------------------+ + | Command line | + | Stack/heap | For use by the kernel real-mode code. +098000 +------------------------+ + | Kernel setup | The kernel real-mode code. +090200 +------------------------+ + | Kernel boot sector | The kernel legacy boot sector. +090000 +------------------------+ + | Protected-mode kernel | The bulk of the kernel image. +010000 +------------------------+ + | Boot loader | <- Boot sector entry point 0000:7C00 +001000 +------------------------+ + | Reserved for MBR/BIOS | +000800 +------------------------+ + | Typically used by MBR | +000600 +------------------------+ + | BIOS use only | +000000 +------------------------+ + + +When using bzImage, the protected-mode kernel was relocated to +0x100000 ("high memory"), and the kernel real-mode block (boot sector, +setup, and stack/heap) was made relocatable to any address between +0x10000 and end of low memory. Unfortunately, in protocols 2.00 and +2.01 the 0x90000+ memory range is still used internally by the kernel; +the 2.02 protocol resolves that problem. + +It is desirable to keep the "memory ceiling" -- the highest point in +low memory touched by the boot loader -- as low as possible, since +some newer BIOSes have begun to allocate some rather large amounts of +memory, called the Extended BIOS Data Area, near the top of low +memory. The boot loader should use the "INT 12h" BIOS call to verify +how much low memory is available. + +Unfortunately, if INT 12h reports that the amount of memory is too +low, there is usually nothing the boot loader can do but to report an +error to the user. The boot loader should therefore be designed to +take up as little space in low memory as it reasonably can. For +zImage or old bzImage kernels, which need data written into the +0x90000 segment, the boot loader should make sure not to use memory +above the 0x9A000 point; too many BIOSes will break above that point. + +For a modern bzImage kernel with boot protocol version >= 2.02, a +memory layout like the following is suggested: + + ~ ~ + | Protected-mode kernel | +100000 +------------------------+ + | I/O memory hole | +0A0000 +------------------------+ + | Reserved for BIOS | Leave as much as possible unused + ~ ~ + | Command line | (Can also be below the X+10000 mark) +X+10000 +------------------------+ + | Stack/heap | For use by the kernel real-mode code. +X+08000 +------------------------+ + | Kernel setup | The kernel real-mode code. + | Kernel boot sector | The kernel legacy boot sector. +X +------------------------+ + | Boot loader | <- Boot sector entry point 0000:7C00 +001000 +------------------------+ + | Reserved for MBR/BIOS | +000800 +------------------------+ + | Typically used by MBR | +000600 +------------------------+ + | BIOS use only | +000000 +------------------------+ + +... where the address X is as low as the design of the boot loader +permits. + + +**** THE REAL-MODE KERNEL HEADER + +In the following text, and anywhere in the kernel boot sequence, "a +sector" refers to 512 bytes. It is independent of the actual sector +size of the underlying medium. + +The first step in loading a Linux kernel should be to load the +real-mode code (boot sector and setup code) and then examine the +following header at offset 0x01f1. The real-mode code can total up to +32K, although the boot loader may choose to load only the first two +sectors (1K) and then examine the bootup sector size. + +The header looks like: + +Offset Proto Name Meaning +/Size + +01F1/1 ALL(1 setup_sects The size of the setup in sectors +01F2/2 ALL root_flags If set, the root is mounted readonly +01F4/4 2.04+(2 syssize The size of the 32-bit code in 16-byte paras +01F8/2 ALL ram_size DO NOT USE - for bootsect.S use only +01FA/2 ALL vid_mode Video mode control +01FC/2 ALL root_dev Default root device number +01FE/2 ALL boot_flag 0xAA55 magic number +0200/2 2.00+ jump Jump instruction +0202/4 2.00+ header Magic signature "HdrS" +0206/2 2.00+ version Boot protocol version supported +0208/4 2.00+ realmode_swtch Boot loader hook (see below) +020C/2 2.00+ start_sys The load-low segment (0x1000) (obsolete) +020E/2 2.00+ kernel_version Pointer to kernel version string +0210/1 2.00+ type_of_loader Boot loader identifier +0211/1 2.00+ loadflags Boot protocol option flags +0212/2 2.00+ setup_move_size Move to high memory size (used with hooks) +0214/4 2.00+ code32_start Boot loader hook (see below) +0218/4 2.00+ ramdisk_image initrd load address (set by boot loader) +021C/4 2.00+ ramdisk_size initrd size (set by boot loader) +0220/4 2.00+ bootsect_kludge DO NOT USE - for bootsect.S use only +0224/2 2.01+ heap_end_ptr Free memory after setup end +0226/2 N/A pad1 Unused +0228/4 2.02+ cmd_line_ptr 32-bit pointer to the kernel command line +022C/4 2.03+ initrd_addr_max Highest legal initrd address +0230/4 2.05+ kernel_alignment Physical addr alignment required for kernel +0234/1 2.05+ relocatable_kernel Whether kernel is relocatable or not +0235/3 N/A pad2 Unused +0238/4 2.06+ cmdline_size Maximum size of the kernel command line +023C/4 2.07+ hardware_subarch Hardware subarchitecture +0240/8 2.07+ hardware_subarch_data Subarchitecture-specific data +0248/4 2.08+ payload_offset Offset of kernel payload +024C/4 2.08+ payload_length Length of kernel payload +0250/8 2.09+ setup_data 64-bit physical pointer to linked list + of struct setup_data + +(1) For backwards compatibility, if the setup_sects field contains 0, the + real value is 4. + +(2) For boot protocol prior to 2.04, the upper two bytes of the syssize + field are unusable, which means the size of a bzImage kernel + cannot be determined. + +If the "HdrS" (0x53726448) magic number is not found at offset 0x202, +the boot protocol version is "old". Loading an old kernel, the +following parameters should be assumed: + + Image type = zImage + initrd not supported + Real-mode kernel must be located at 0x90000. + +Otherwise, the "version" field contains the protocol version, +e.g. protocol version 2.01 will contain 0x0201 in this field. When +setting fields in the header, you must make sure only to set fields +supported by the protocol version in use. + + +**** DETAILS OF HEADER FIELDS + +For each field, some are information from the kernel to the bootloader +("read"), some are expected to be filled out by the bootloader +("write"), and some are expected to be read and modified by the +bootloader ("modify"). + +All general purpose boot loaders should write the fields marked +(obligatory). Boot loaders who want to load the kernel at a +nonstandard address should fill in the fields marked (reloc); other +boot loaders can ignore those fields. + +The byte order of all fields is littleendian (this is x86, after all.) + +Field name: setup_sects +Type: read +Offset/size: 0x1f1/1 +Protocol: ALL + + The size of the setup code in 512-byte sectors. If this field is + 0, the real value is 4. The real-mode code consists of the boot + sector (always one 512-byte sector) plus the setup code. + +Field name: root_flags +Type: modify (optional) +Offset/size: 0x1f2/2 +Protocol: ALL + + If this field is nonzero, the root defaults to readonly. The use of + this field is deprecated; use the "ro" or "rw" options on the + command line instead. + +Field name: syssize +Type: read +Offset/size: 0x1f4/4 (protocol 2.04+) 0x1f4/2 (protocol ALL) +Protocol: 2.04+ + + The size of the protected-mode code in units of 16-byte paragraphs. + For protocol versions older than 2.04 this field is only two bytes + wide, and therefore cannot be trusted for the size of a kernel if + the LOAD_HIGH flag is set. + +Field name: ram_size +Type: kernel internal +Offset/size: 0x1f8/2 +Protocol: ALL + + This field is obsolete. + +Field name: vid_mode +Type: modify (obligatory) +Offset/size: 0x1fa/2 + + Please see the section on SPECIAL COMMAND LINE OPTIONS. + +Field name: root_dev +Type: modify (optional) +Offset/size: 0x1fc/2 +Protocol: ALL + + The default root device device number. The use of this field is + deprecated, use the "root=" option on the command line instead. + +Field name: boot_flag +Type: read +Offset/size: 0x1fe/2 +Protocol: ALL + + Contains 0xAA55. This is the closest thing old Linux kernels have + to a magic number. + +Field name: jump +Type: read +Offset/size: 0x200/2 +Protocol: 2.00+ + + Contains an x86 jump instruction, 0xEB followed by a signed offset + relative to byte 0x202. This can be used to determine the size of + the header. + +Field name: header +Type: read +Offset/size: 0x202/4 +Protocol: 2.00+ + + Contains the magic number "HdrS" (0x53726448). + +Field name: version +Type: read +Offset/size: 0x206/2 +Protocol: 2.00+ + + Contains the boot protocol version, in (major << 8)+minor format, + e.g. 0x0204 for version 2.04, and 0x0a11 for a hypothetical version + 10.17. + +Field name: readmode_swtch +Type: modify (optional) +Offset/size: 0x208/4 +Protocol: 2.00+ + + Boot loader hook (see ADVANCED BOOT LOADER HOOKS below.) + +Field name: start_sys +Type: read +Offset/size: 0x20c/4 +Protocol: 2.00+ + + The load low segment (0x1000). Obsolete. + +Field name: kernel_version +Type: read +Offset/size: 0x20e/2 +Protocol: 2.00+ + + If set to a nonzero value, contains a pointer to a NUL-terminated + human-readable kernel version number string, less 0x200. This can + be used to display the kernel version to the user. This value + should be less than (0x200*setup_sects). + + For example, if this value is set to 0x1c00, the kernel version + number string can be found at offset 0x1e00 in the kernel file. + This is a valid value if and only if the "setup_sects" field + contains the value 15 or higher, as: + + 0x1c00 < 15*0x200 (= 0x1e00) but + 0x1c00 >= 14*0x200 (= 0x1c00) + + 0x1c00 >> 9 = 14, so the minimum value for setup_secs is 15. + +Field name: type_of_loader +Type: write (obligatory) +Offset/size: 0x210/1 +Protocol: 2.00+ + + If your boot loader has an assigned id (see table below), enter + 0xTV here, where T is an identifier for the boot loader and V is + a version number. Otherwise, enter 0xFF here. + + Assigned boot loader ids: + 0 LILO (0x00 reserved for pre-2.00 bootloader) + 1 Loadlin + 2 bootsect-loader (0x20, all other values reserved) + 3 SYSLINUX + 4 EtherBoot + 5 ELILO + 7 GRuB + 8 U-BOOT + 9 Xen + A Gujin + B Qemu + + Please contact if you need a bootloader ID + value assigned. + +Field name: loadflags +Type: modify (obligatory) +Offset/size: 0x211/1 +Protocol: 2.00+ + + This field is a bitmask. + + Bit 0 (read): LOADED_HIGH + - If 0, the protected-mode code is loaded at 0x10000. + - If 1, the protected-mode code is loaded at 0x100000. + + Bit 5 (write): QUIET_FLAG + - If 0, print early messages. + - If 1, suppress early messages. + This requests to the kernel (decompressor and early + kernel) to not write early messages that require + accessing the display hardware directly. + + Bit 6 (write): KEEP_SEGMENTS + Protocol: 2.07+ + - If 0, reload the segment registers in the 32bit entry point. + - If 1, do not reload the segment registers in the 32bit entry point. + Assume that %cs %ds %ss %es are all set to flat segments with + a base of 0 (or the equivalent for their environment). + + Bit 7 (write): CAN_USE_HEAP + Set this bit to 1 to indicate that the value entered in the + heap_end_ptr is valid. If this field is clear, some setup code + functionality will be disabled. + +Field name: setup_move_size +Type: modify (obligatory) +Offset/size: 0x212/2 +Protocol: 2.00-2.01 + + When using protocol 2.00 or 2.01, if the real mode kernel is not + loaded at 0x90000, it gets moved there later in the loading + sequence. Fill in this field if you want additional data (such as + the kernel command line) moved in addition to the real-mode kernel + itself. + + The unit is bytes starting with the beginning of the boot sector. + + This field is can be ignored when the protocol is 2.02 or higher, or + if the real-mode code is loaded at 0x90000. + +Field name: code32_start +Type: modify (optional, reloc) +Offset/size: 0x214/4 +Protocol: 2.00+ + + The address to jump to in protected mode. This defaults to the load + address of the kernel, and can be used by the boot loader to + determine the proper load address. + + This field can be modified for two purposes: + + 1. as a boot loader hook (see ADVANCED BOOT LOADER HOOKS below.) + + 2. if a bootloader which does not install a hook loads a + relocatable kernel at a nonstandard address it will have to modify + this field to point to the load address. + +Field name: ramdisk_image +Type: write (obligatory) +Offset/size: 0x218/4 +Protocol: 2.00+ + + The 32-bit linear address of the initial ramdisk or ramfs. Leave at + zero if there is no initial ramdisk/ramfs. + +Field name: ramdisk_size +Type: write (obligatory) +Offset/size: 0x21c/4 +Protocol: 2.00+ + + Size of the initial ramdisk or ramfs. Leave at zero if there is no + initial ramdisk/ramfs. + +Field name: bootsect_kludge +Type: kernel internal +Offset/size: 0x220/4 +Protocol: 2.00+ + + This field is obsolete. + +Field name: heap_end_ptr +Type: write (obligatory) +Offset/size: 0x224/2 +Protocol: 2.01+ + + Set this field to the offset (from the beginning of the real-mode + code) of the end of the setup stack/heap, minus 0x0200. + +Field name: cmd_line_ptr +Type: write (obligatory) +Offset/size: 0x228/4 +Protocol: 2.02+ + + Set this field to the linear address of the kernel command line. + The kernel command line can be located anywhere between the end of + the setup heap and 0xA0000; it does not have to be located in the + same 64K segment as the real-mode code itself. + + Fill in this field even if your boot loader does not support a + command line, in which case you can point this to an empty string + (or better yet, to the string "auto".) If this field is left at + zero, the kernel will assume that your boot loader does not support + the 2.02+ protocol. + +Field name: initrd_addr_max +Type: read +Offset/size: 0x22c/4 +Protocol: 2.03+ + + The maximum address that may be occupied by the initial + ramdisk/ramfs contents. For boot protocols 2.02 or earlier, this + field is not present, and the maximum address is 0x37FFFFFF. (This + address is defined as the address of the highest safe byte, so if + your ramdisk is exactly 131072 bytes long and this field is + 0x37FFFFFF, you can start your ramdisk at 0x37FE0000.) + +Field name: kernel_alignment +Type: read (reloc) +Offset/size: 0x230/4 +Protocol: 2.05+ + + Alignment unit required by the kernel (if relocatable_kernel is true.) + +Field name: relocatable_kernel +Type: read (reloc) +Offset/size: 0x234/1 +Protocol: 2.05+ + + If this field is nonzero, the protected-mode part of the kernel can + be loaded at any address that satisfies the kernel_alignment field. + After loading, the boot loader must set the code32_start field to + point to the loaded code, or to a boot loader hook. + +Field name: cmdline_size +Type: read +Offset/size: 0x238/4 +Protocol: 2.06+ + + The maximum size of the command line without the terminating + zero. This means that the command line can contain at most + cmdline_size characters. With protocol version 2.05 and earlier, the + maximum size was 255. + +Field name: hardware_subarch +Type: write (optional, defaults to x86/PC) +Offset/size: 0x23c/4 +Protocol: 2.07+ + + In a paravirtualized environment the hardware low level architectural + pieces such as interrupt handling, page table handling, and + accessing process control registers needs to be done differently. + + This field allows the bootloader to inform the kernel we are in one + one of those environments. + + 0x00000000 The default x86/PC environment + 0x00000001 lguest + 0x00000002 Xen + +Field name: hardware_subarch_data +Type: write (subarch-dependent) +Offset/size: 0x240/8 +Protocol: 2.07+ + + A pointer to data that is specific to hardware subarch + This field is currently unused for the default x86/PC environment, + do not modify. + +Field name: payload_offset +Type: read +Offset/size: 0x248/4 +Protocol: 2.08+ + + If non-zero then this field contains the offset from the end of the + real-mode code to the payload. + + The payload may be compressed. The format of both the compressed and + uncompressed data should be determined using the standard magic + numbers. Currently only gzip compressed ELF is used. + +Field name: payload_length +Type: read +Offset/size: 0x24c/4 +Protocol: 2.08+ + + The length of the payload. + +Field name: setup_data +Type: write (special) +Offset/size: 0x250/8 +Protocol: 2.09+ + + The 64-bit physical pointer to NULL terminated single linked list of + struct setup_data. This is used to define a more extensible boot + parameters passing mechanism. The definition of struct setup_data is + as follow: + + struct setup_data { + u64 next; + u32 type; + u32 len; + u8 data[0]; + }; + + Where, the next is a 64-bit physical pointer to the next node of + linked list, the next field of the last node is 0; the type is used + to identify the contents of data; the len is the length of data + field; the data holds the real payload. + + This list may be modified at a number of points during the bootup + process. Therefore, when modifying this list one should always make + sure to consider the case where the linked list already contains + entries. + + +**** THE IMAGE CHECKSUM + +From boot protocol version 2.08 onwards the CRC-32 is calculated over +the entire file using the characteristic polynomial 0x04C11DB7 and an +initial remainder of 0xffffffff. The checksum is appended to the +file; therefore the CRC of the file up to the limit specified in the +syssize field of the header is always 0. + + +**** THE KERNEL COMMAND LINE + +The kernel command line has become an important way for the boot +loader to communicate with the kernel. Some of its options are also +relevant to the boot loader itself, see "special command line options" +below. + +The kernel command line is a null-terminated string. The maximum +length can be retrieved from the field cmdline_size. Before protocol +version 2.06, the maximum was 255 characters. A string that is too +long will be automatically truncated by the kernel. + +If the boot protocol version is 2.02 or later, the address of the +kernel command line is given by the header field cmd_line_ptr (see +above.) This address can be anywhere between the end of the setup +heap and 0xA0000. + +If the protocol version is *not* 2.02 or higher, the kernel +command line is entered using the following protocol: + + At offset 0x0020 (word), "cmd_line_magic", enter the magic + number 0xA33F. + + At offset 0x0022 (word), "cmd_line_offset", enter the offset + of the kernel command line (relative to the start of the + real-mode kernel). + + The kernel command line *must* be within the memory region + covered by setup_move_size, so you may need to adjust this + field. + + +**** MEMORY LAYOUT OF THE REAL-MODE CODE + +The real-mode code requires a stack/heap to be set up, as well as +memory allocated for the kernel command line. This needs to be done +in the real-mode accessible memory in bottom megabyte. + +It should be noted that modern machines often have a sizable Extended +BIOS Data Area (EBDA). As a result, it is advisable to use as little +of the low megabyte as possible. + +Unfortunately, under the following circumstances the 0x90000 memory +segment has to be used: + + - When loading a zImage kernel ((loadflags & 0x01) == 0). + - When loading a 2.01 or earlier boot protocol kernel. + + -> For the 2.00 and 2.01 boot protocols, the real-mode code + can be loaded at another address, but it is internally + relocated to 0x90000. For the "old" protocol, the + real-mode code must be loaded at 0x90000. + +When loading at 0x90000, avoid using memory above 0x9a000. + +For boot protocol 2.02 or higher, the command line does not have to be +located in the same 64K segment as the real-mode setup code; it is +thus permitted to give the stack/heap the full 64K segment and locate +the command line above it. + +The kernel command line should not be located below the real-mode +code, nor should it be located in high memory. + + +**** SAMPLE BOOT CONFIGURATION + +As a sample configuration, assume the following layout of the real +mode segment: + + When loading below 0x90000, use the entire segment: + + 0x0000-0x7fff Real mode kernel + 0x8000-0xdfff Stack and heap + 0xe000-0xffff Kernel command line + + When loading at 0x90000 OR the protocol version is 2.01 or earlier: + + 0x0000-0x7fff Real mode kernel + 0x8000-0x97ff Stack and heap + 0x9800-0x9fff Kernel command line + +Such a boot loader should enter the following fields in the header: + + unsigned long base_ptr; /* base address for real-mode segment */ + + if ( setup_sects == 0 ) { + setup_sects = 4; + } + + if ( protocol >= 0x0200 ) { + type_of_loader = ; + if ( loading_initrd ) { + ramdisk_image = ; + ramdisk_size = ; + } + + if ( protocol >= 0x0202 && loadflags & 0x01 ) + heap_end = 0xe000; + else + heap_end = 0x9800; + + if ( protocol >= 0x0201 ) { + heap_end_ptr = heap_end - 0x200; + loadflags |= 0x80; /* CAN_USE_HEAP */ + } + + if ( protocol >= 0x0202 ) { + cmd_line_ptr = base_ptr + heap_end; + strcpy(cmd_line_ptr, cmdline); + } else { + cmd_line_magic = 0xA33F; + cmd_line_offset = heap_end; + setup_move_size = heap_end + strlen(cmdline)+1; + strcpy(base_ptr+cmd_line_offset, cmdline); + } + } else { + /* Very old kernel */ + + heap_end = 0x9800; + + cmd_line_magic = 0xA33F; + cmd_line_offset = heap_end; + + /* A very old kernel MUST have its real-mode code + loaded at 0x90000 */ + + if ( base_ptr != 0x90000 ) { + /* Copy the real-mode kernel */ + memcpy(0x90000, base_ptr, (setup_sects+1)*512); + base_ptr = 0x90000; /* Relocated */ + } + + strcpy(0x90000+cmd_line_offset, cmdline); + + /* It is recommended to clear memory up to the 32K mark */ + memset(0x90000 + (setup_sects+1)*512, 0, + (64-(setup_sects+1))*512); + } + + +**** LOADING THE REST OF THE KERNEL + +The 32-bit (non-real-mode) kernel starts at offset (setup_sects+1)*512 +in the kernel file (again, if setup_sects == 0 the real value is 4.) +It should be loaded at address 0x10000 for Image/zImage kernels and +0x100000 for bzImage kernels. + +The kernel is a bzImage kernel if the protocol >= 2.00 and the 0x01 +bit (LOAD_HIGH) in the loadflags field is set: + + is_bzImage = (protocol >= 0x0200) && (loadflags & 0x01); + load_address = is_bzImage ? 0x100000 : 0x10000; + +Note that Image/zImage kernels can be up to 512K in size, and thus use +the entire 0x10000-0x90000 range of memory. This means it is pretty +much a requirement for these kernels to load the real-mode part at +0x90000. bzImage kernels allow much more flexibility. + + +**** SPECIAL COMMAND LINE OPTIONS + +If the command line provided by the boot loader is entered by the +user, the user may expect the following command line options to work. +They should normally not be deleted from the kernel command line even +though not all of them are actually meaningful to the kernel. Boot +loader authors who need additional command line options for the boot +loader itself should get them registered in +Documentation/kernel-parameters.txt to make sure they will not +conflict with actual kernel options now or in the future. + + vga= + here is either an integer (in C notation, either + decimal, octal, or hexadecimal) or one of the strings + "normal" (meaning 0xFFFF), "ext" (meaning 0xFFFE) or "ask" + (meaning 0xFFFD). This value should be entered into the + vid_mode field, as it is used by the kernel before the command + line is parsed. + + mem= + is an integer in C notation optionally followed by + (case insensitive) K, M, G, T, P or E (meaning << 10, << 20, + << 30, << 40, << 50 or << 60). This specifies the end of + memory to the kernel. This affects the possible placement of + an initrd, since an initrd should be placed near end of + memory. Note that this is an option to *both* the kernel and + the bootloader! + + initrd= + An initrd should be loaded. The meaning of is + obviously bootloader-dependent, and some boot loaders + (e.g. LILO) do not have such a command. + +In addition, some boot loaders add the following options to the +user-specified command line: + + BOOT_IMAGE= + The boot image which was loaded. Again, the meaning of + is obviously bootloader-dependent. + + auto + The kernel was booted without explicit user intervention. + +If these options are added by the boot loader, it is highly +recommended that they are located *first*, before the user-specified +or configuration-specified command line. Otherwise, "init=/bin/sh" +gets confused by the "auto" option. + + +**** RUNNING THE KERNEL + +The kernel is started by jumping to the kernel entry point, which is +located at *segment* offset 0x20 from the start of the real mode +kernel. This means that if you loaded your real-mode kernel code at +0x90000, the kernel entry point is 9020:0000. + +At entry, ds = es = ss should point to the start of the real-mode +kernel code (0x9000 if the code is loaded at 0x90000), sp should be +set up properly, normally pointing to the top of the heap, and +interrupts should be disabled. Furthermore, to guard against bugs in +the kernel, it is recommended that the boot loader sets fs = gs = ds = +es = ss. + +In our example from above, we would do: + + /* Note: in the case of the "old" kernel protocol, base_ptr must + be == 0x90000 at this point; see the previous sample code */ + + seg = base_ptr >> 4; + + cli(); /* Enter with interrupts disabled! */ + + /* Set up the real-mode kernel stack */ + _SS = seg; + _SP = heap_end; + + _DS = _ES = _FS = _GS = seg; + jmp_far(seg+0x20, 0); /* Run the kernel */ + +If your boot sector accesses a floppy drive, it is recommended to +switch off the floppy motor before running the kernel, since the +kernel boot leaves interrupts off and thus the motor will not be +switched off, especially if the loaded kernel has the floppy driver as +a demand-loaded module! + + +**** ADVANCED BOOT LOADER HOOKS + +If the boot loader runs in a particularly hostile environment (such as +LOADLIN, which runs under DOS) it may be impossible to follow the +standard memory location requirements. Such a boot loader may use the +following hooks that, if set, are invoked by the kernel at the +appropriate time. The use of these hooks should probably be +considered an absolutely last resort! + +IMPORTANT: All the hooks are required to preserve %esp, %ebp, %esi and +%edi across invocation. + + realmode_swtch: + A 16-bit real mode far subroutine invoked immediately before + entering protected mode. The default routine disables NMI, so + your routine should probably do so, too. + + code32_start: + A 32-bit flat-mode routine *jumped* to immediately after the + transition to protected mode, but before the kernel is + uncompressed. No segments, except CS, are guaranteed to be + set up (current kernels do, but older ones do not); you should + set them up to BOOT_DS (0x18) yourself. + + After completing your hook, you should jump to the address + that was in this field before your boot loader overwrote it + (relocated, if appropriate.) + + +**** 32-bit BOOT PROTOCOL + +For machine with some new BIOS other than legacy BIOS, such as EFI, +LinuxBIOS, etc, and kexec, the 16-bit real mode setup code in kernel +based on legacy BIOS can not be used, so a 32-bit boot protocol needs +to be defined. + +In 32-bit boot protocol, the first step in loading a Linux kernel +should be to setup the boot parameters (struct boot_params, +traditionally known as "zero page"). The memory for struct boot_params +should be allocated and initialized to all zero. Then the setup header +from offset 0x01f1 of kernel image on should be loaded into struct +boot_params and examined. The end of setup header can be calculated as +follow: + + 0x0202 + byte value at offset 0x0201 + +In addition to read/modify/write the setup header of the struct +boot_params as that of 16-bit boot protocol, the boot loader should +also fill the additional fields of the struct boot_params as that +described in zero-page.txt. + +After setupping the struct boot_params, the boot loader can load the +32/64-bit kernel in the same way as that of 16-bit boot protocol. + +In 32-bit boot protocol, the kernel is started by jumping to the +32-bit kernel entry point, which is the start address of loaded +32/64-bit kernel. + +At entry, the CPU must be in 32-bit protected mode with paging +disabled; a GDT must be loaded with the descriptors for selectors +__BOOT_CS(0x10) and __BOOT_DS(0x18); both descriptors must be 4G flat +segment; __BOOS_CS must have execute/read permission, and __BOOT_DS +must have read/write permission; CS must be __BOOT_CS and DS, ES, SS +must be __BOOT_DS; interrupt must be disabled; %esi must hold the base +address of the struct boot_params; %ebp, %edi and %ebx must be zero. diff --git a/Documentation/x86/i386/boot.txt b/Documentation/x86/i386/boot.txt deleted file mode 100644 index 147bfe511cd..00000000000 --- a/Documentation/x86/i386/boot.txt +++ /dev/null @@ -1,900 +0,0 @@ - THE LINUX/x86 BOOT PROTOCOL - --------------------------- - -On the x86 platform, the Linux kernel uses a rather complicated boot -convention. This has evolved partially due to historical aspects, as -well as the desire in the early days to have the kernel itself be a -bootable image, the complicated PC memory model and due to changed -expectations in the PC industry caused by the effective demise of -real-mode DOS as a mainstream operating system. - -Currently, the following versions of the Linux/x86 boot protocol exist. - -Old kernels: zImage/Image support only. Some very early kernels - may not even support a command line. - -Protocol 2.00: (Kernel 1.3.73) Added bzImage and initrd support, as - well as a formalized way to communicate between the - boot loader and the kernel. setup.S made relocatable, - although the traditional setup area still assumed - writable. - -Protocol 2.01: (Kernel 1.3.76) Added a heap overrun warning. - -Protocol 2.02: (Kernel 2.4.0-test3-pre3) New command line protocol. - Lower the conventional memory ceiling. No overwrite - of the traditional setup area, thus making booting - safe for systems which use the EBDA from SMM or 32-bit - BIOS entry points. zImage deprecated but still - supported. - -Protocol 2.03: (Kernel 2.4.18-pre1) Explicitly makes the highest possible - initrd address available to the bootloader. - -Protocol 2.04: (Kernel 2.6.14) Extend the syssize field to four bytes. - -Protocol 2.05: (Kernel 2.6.20) Make protected mode kernel relocatable. - Introduce relocatable_kernel and kernel_alignment fields. - -Protocol 2.06: (Kernel 2.6.22) Added a field that contains the size of - the boot command line. - -Protocol 2.07: (Kernel 2.6.24) Added paravirtualised boot protocol. - Introduced hardware_subarch and hardware_subarch_data - and KEEP_SEGMENTS flag in load_flags. - -Protocol 2.08: (Kernel 2.6.26) Added crc32 checksum and ELF format - payload. Introduced payload_offset and payload length - fields to aid in locating the payload. - -Protocol 2.09: (Kernel 2.6.26) Added a field of 64-bit physical - pointer to single linked list of struct setup_data. - -**** MEMORY LAYOUT - -The traditional memory map for the kernel loader, used for Image or -zImage kernels, typically looks like: - - | | -0A0000 +------------------------+ - | Reserved for BIOS | Do not use. Reserved for BIOS EBDA. -09A000 +------------------------+ - | Command line | - | Stack/heap | For use by the kernel real-mode code. -098000 +------------------------+ - | Kernel setup | The kernel real-mode code. -090200 +------------------------+ - | Kernel boot sector | The kernel legacy boot sector. -090000 +------------------------+ - | Protected-mode kernel | The bulk of the kernel image. -010000 +------------------------+ - | Boot loader | <- Boot sector entry point 0000:7C00 -001000 +------------------------+ - | Reserved for MBR/BIOS | -000800 +------------------------+ - | Typically used by MBR | -000600 +------------------------+ - | BIOS use only | -000000 +------------------------+ - - -When using bzImage, the protected-mode kernel was relocated to -0x100000 ("high memory"), and the kernel real-mode block (boot sector, -setup, and stack/heap) was made relocatable to any address between -0x10000 and end of low memory. Unfortunately, in protocols 2.00 and -2.01 the 0x90000+ memory range is still used internally by the kernel; -the 2.02 protocol resolves that problem. - -It is desirable to keep the "memory ceiling" -- the highest point in -low memory touched by the boot loader -- as low as possible, since -some newer BIOSes have begun to allocate some rather large amounts of -memory, called the Extended BIOS Data Area, near the top of low -memory. The boot loader should use the "INT 12h" BIOS call to verify -how much low memory is available. - -Unfortunately, if INT 12h reports that the amount of memory is too -low, there is usually nothing the boot loader can do but to report an -error to the user. The boot loader should therefore be designed to -take up as little space in low memory as it reasonably can. For -zImage or old bzImage kernels, which need data written into the -0x90000 segment, the boot loader should make sure not to use memory -above the 0x9A000 point; too many BIOSes will break above that point. - -For a modern bzImage kernel with boot protocol version >= 2.02, a -memory layout like the following is suggested: - - ~ ~ - | Protected-mode kernel | -100000 +------------------------+ - | I/O memory hole | -0A0000 +------------------------+ - | Reserved for BIOS | Leave as much as possible unused - ~ ~ - | Command line | (Can also be below the X+10000 mark) -X+10000 +------------------------+ - | Stack/heap | For use by the kernel real-mode code. -X+08000 +------------------------+ - | Kernel setup | The kernel real-mode code. - | Kernel boot sector | The kernel legacy boot sector. -X +------------------------+ - | Boot loader | <- Boot sector entry point 0000:7C00 -001000 +------------------------+ - | Reserved for MBR/BIOS | -000800 +------------------------+ - | Typically used by MBR | -000600 +------------------------+ - | BIOS use only | -000000 +------------------------+ - -... where the address X is as low as the design of the boot loader -permits. - - -**** THE REAL-MODE KERNEL HEADER - -In the following text, and anywhere in the kernel boot sequence, "a -sector" refers to 512 bytes. It is independent of the actual sector -size of the underlying medium. - -The first step in loading a Linux kernel should be to load the -real-mode code (boot sector and setup code) and then examine the -following header at offset 0x01f1. The real-mode code can total up to -32K, although the boot loader may choose to load only the first two -sectors (1K) and then examine the bootup sector size. - -The header looks like: - -Offset Proto Name Meaning -/Size - -01F1/1 ALL(1 setup_sects The size of the setup in sectors -01F2/2 ALL root_flags If set, the root is mounted readonly -01F4/4 2.04+(2 syssize The size of the 32-bit code in 16-byte paras -01F8/2 ALL ram_size DO NOT USE - for bootsect.S use only -01FA/2 ALL vid_mode Video mode control -01FC/2 ALL root_dev Default root device number -01FE/2 ALL boot_flag 0xAA55 magic number -0200/2 2.00+ jump Jump instruction -0202/4 2.00+ header Magic signature "HdrS" -0206/2 2.00+ version Boot protocol version supported -0208/4 2.00+ realmode_swtch Boot loader hook (see below) -020C/2 2.00+ start_sys The load-low segment (0x1000) (obsolete) -020E/2 2.00+ kernel_version Pointer to kernel version string -0210/1 2.00+ type_of_loader Boot loader identifier -0211/1 2.00+ loadflags Boot protocol option flags -0212/2 2.00+ setup_move_size Move to high memory size (used with hooks) -0214/4 2.00+ code32_start Boot loader hook (see below) -0218/4 2.00+ ramdisk_image initrd load address (set by boot loader) -021C/4 2.00+ ramdisk_size initrd size (set by boot loader) -0220/4 2.00+ bootsect_kludge DO NOT USE - for bootsect.S use only -0224/2 2.01+ heap_end_ptr Free memory after setup end -0226/2 N/A pad1 Unused -0228/4 2.02+ cmd_line_ptr 32-bit pointer to the kernel command line -022C/4 2.03+ initrd_addr_max Highest legal initrd address -0230/4 2.05+ kernel_alignment Physical addr alignment required for kernel -0234/1 2.05+ relocatable_kernel Whether kernel is relocatable or not -0235/3 N/A pad2 Unused -0238/4 2.06+ cmdline_size Maximum size of the kernel command line -023C/4 2.07+ hardware_subarch Hardware subarchitecture -0240/8 2.07+ hardware_subarch_data Subarchitecture-specific data -0248/4 2.08+ payload_offset Offset of kernel payload -024C/4 2.08+ payload_length Length of kernel payload -0250/8 2.09+ setup_data 64-bit physical pointer to linked list - of struct setup_data - -(1) For backwards compatibility, if the setup_sects field contains 0, the - real value is 4. - -(2) For boot protocol prior to 2.04, the upper two bytes of the syssize - field are unusable, which means the size of a bzImage kernel - cannot be determined. - -If the "HdrS" (0x53726448) magic number is not found at offset 0x202, -the boot protocol version is "old". Loading an old kernel, the -following parameters should be assumed: - - Image type = zImage - initrd not supported - Real-mode kernel must be located at 0x90000. - -Otherwise, the "version" field contains the protocol version, -e.g. protocol version 2.01 will contain 0x0201 in this field. When -setting fields in the header, you must make sure only to set fields -supported by the protocol version in use. - - -**** DETAILS OF HEADER FIELDS - -For each field, some are information from the kernel to the bootloader -("read"), some are expected to be filled out by the bootloader -("write"), and some are expected to be read and modified by the -bootloader ("modify"). - -All general purpose boot loaders should write the fields marked -(obligatory). Boot loaders who want to load the kernel at a -nonstandard address should fill in the fields marked (reloc); other -boot loaders can ignore those fields. - -The byte order of all fields is littleendian (this is x86, after all.) - -Field name: setup_sects -Type: read -Offset/size: 0x1f1/1 -Protocol: ALL - - The size of the setup code in 512-byte sectors. If this field is - 0, the real value is 4. The real-mode code consists of the boot - sector (always one 512-byte sector) plus the setup code. - -Field name: root_flags -Type: modify (optional) -Offset/size: 0x1f2/2 -Protocol: ALL - - If this field is nonzero, the root defaults to readonly. The use of - this field is deprecated; use the "ro" or "rw" options on the - command line instead. - -Field name: syssize -Type: read -Offset/size: 0x1f4/4 (protocol 2.04+) 0x1f4/2 (protocol ALL) -Protocol: 2.04+ - - The size of the protected-mode code in units of 16-byte paragraphs. - For protocol versions older than 2.04 this field is only two bytes - wide, and therefore cannot be trusted for the size of a kernel if - the LOAD_HIGH flag is set. - -Field name: ram_size -Type: kernel internal -Offset/size: 0x1f8/2 -Protocol: ALL - - This field is obsolete. - -Field name: vid_mode -Type: modify (obligatory) -Offset/size: 0x1fa/2 - - Please see the section on SPECIAL COMMAND LINE OPTIONS. - -Field name: root_dev -Type: modify (optional) -Offset/size: 0x1fc/2 -Protocol: ALL - - The default root device device number. The use of this field is - deprecated, use the "root=" option on the command line instead. - -Field name: boot_flag -Type: read -Offset/size: 0x1fe/2 -Protocol: ALL - - Contains 0xAA55. This is the closest thing old Linux kernels have - to a magic number. - -Field name: jump -Type: read -Offset/size: 0x200/2 -Protocol: 2.00+ - - Contains an x86 jump instruction, 0xEB followed by a signed offset - relative to byte 0x202. This can be used to determine the size of - the header. - -Field name: header -Type: read -Offset/size: 0x202/4 -Protocol: 2.00+ - - Contains the magic number "HdrS" (0x53726448). - -Field name: version -Type: read -Offset/size: 0x206/2 -Protocol: 2.00+ - - Contains the boot protocol version, in (major << 8)+minor format, - e.g. 0x0204 for version 2.04, and 0x0a11 for a hypothetical version - 10.17. - -Field name: readmode_swtch -Type: modify (optional) -Offset/size: 0x208/4 -Protocol: 2.00+ - - Boot loader hook (see ADVANCED BOOT LOADER HOOKS below.) - -Field name: start_sys -Type: read -Offset/size: 0x20c/4 -Protocol: 2.00+ - - The load low segment (0x1000). Obsolete. - -Field name: kernel_version -Type: read -Offset/size: 0x20e/2 -Protocol: 2.00+ - - If set to a nonzero value, contains a pointer to a NUL-terminated - human-readable kernel version number string, less 0x200. This can - be used to display the kernel version to the user. This value - should be less than (0x200*setup_sects). - - For example, if this value is set to 0x1c00, the kernel version - number string can be found at offset 0x1e00 in the kernel file. - This is a valid value if and only if the "setup_sects" field - contains the value 15 or higher, as: - - 0x1c00 < 15*0x200 (= 0x1e00) but - 0x1c00 >= 14*0x200 (= 0x1c00) - - 0x1c00 >> 9 = 14, so the minimum value for setup_secs is 15. - -Field name: type_of_loader -Type: write (obligatory) -Offset/size: 0x210/1 -Protocol: 2.00+ - - If your boot loader has an assigned id (see table below), enter - 0xTV here, where T is an identifier for the boot loader and V is - a version number. Otherwise, enter 0xFF here. - - Assigned boot loader ids: - 0 LILO (0x00 reserved for pre-2.00 bootloader) - 1 Loadlin - 2 bootsect-loader (0x20, all other values reserved) - 3 SYSLINUX - 4 EtherBoot - 5 ELILO - 7 GRuB - 8 U-BOOT - 9 Xen - A Gujin - B Qemu - - Please contact if you need a bootloader ID - value assigned. - -Field name: loadflags -Type: modify (obligatory) -Offset/size: 0x211/1 -Protocol: 2.00+ - - This field is a bitmask. - - Bit 0 (read): LOADED_HIGH - - If 0, the protected-mode code is loaded at 0x10000. - - If 1, the protected-mode code is loaded at 0x100000. - - Bit 5 (write): QUIET_FLAG - - If 0, print early messages. - - If 1, suppress early messages. - This requests to the kernel (decompressor and early - kernel) to not write early messages that require - accessing the display hardware directly. - - Bit 6 (write): KEEP_SEGMENTS - Protocol: 2.07+ - - If 0, reload the segment registers in the 32bit entry point. - - If 1, do not reload the segment registers in the 32bit entry point. - Assume that %cs %ds %ss %es are all set to flat segments with - a base of 0 (or the equivalent for their environment). - - Bit 7 (write): CAN_USE_HEAP - Set this bit to 1 to indicate that the value entered in the - heap_end_ptr is valid. If this field is clear, some setup code - functionality will be disabled. - -Field name: setup_move_size -Type: modify (obligatory) -Offset/size: 0x212/2 -Protocol: 2.00-2.01 - - When using protocol 2.00 or 2.01, if the real mode kernel is not - loaded at 0x90000, it gets moved there later in the loading - sequence. Fill in this field if you want additional data (such as - the kernel command line) moved in addition to the real-mode kernel - itself. - - The unit is bytes starting with the beginning of the boot sector. - - This field is can be ignored when the protocol is 2.02 or higher, or - if the real-mode code is loaded at 0x90000. - -Field name: code32_start -Type: modify (optional, reloc) -Offset/size: 0x214/4 -Protocol: 2.00+ - - The address to jump to in protected mode. This defaults to the load - address of the kernel, and can be used by the boot loader to - determine the proper load address. - - This field can be modified for two purposes: - - 1. as a boot loader hook (see ADVANCED BOOT LOADER HOOKS below.) - - 2. if a bootloader which does not install a hook loads a - relocatable kernel at a nonstandard address it will have to modify - this field to point to the load address. - -Field name: ramdisk_image -Type: write (obligatory) -Offset/size: 0x218/4 -Protocol: 2.00+ - - The 32-bit linear address of the initial ramdisk or ramfs. Leave at - zero if there is no initial ramdisk/ramfs. - -Field name: ramdisk_size -Type: write (obligatory) -Offset/size: 0x21c/4 -Protocol: 2.00+ - - Size of the initial ramdisk or ramfs. Leave at zero if there is no - initial ramdisk/ramfs. - -Field name: bootsect_kludge -Type: kernel internal -Offset/size: 0x220/4 -Protocol: 2.00+ - - This field is obsolete. - -Field name: heap_end_ptr -Type: write (obligatory) -Offset/size: 0x224/2 -Protocol: 2.01+ - - Set this field to the offset (from the beginning of the real-mode - code) of the end of the setup stack/heap, minus 0x0200. - -Field name: cmd_line_ptr -Type: write (obligatory) -Offset/size: 0x228/4 -Protocol: 2.02+ - - Set this field to the linear address of the kernel command line. - The kernel command line can be located anywhere between the end of - the setup heap and 0xA0000; it does not have to be located in the - same 64K segment as the real-mode code itself. - - Fill in this field even if your boot loader does not support a - command line, in which case you can point this to an empty string - (or better yet, to the string "auto".) If this field is left at - zero, the kernel will assume that your boot loader does not support - the 2.02+ protocol. - -Field name: initrd_addr_max -Type: read -Offset/size: 0x22c/4 -Protocol: 2.03+ - - The maximum address that may be occupied by the initial - ramdisk/ramfs contents. For boot protocols 2.02 or earlier, this - field is not present, and the maximum address is 0x37FFFFFF. (This - address is defined as the address of the highest safe byte, so if - your ramdisk is exactly 131072 bytes long and this field is - 0x37FFFFFF, you can start your ramdisk at 0x37FE0000.) - -Field name: kernel_alignment -Type: read (reloc) -Offset/size: 0x230/4 -Protocol: 2.05+ - - Alignment unit required by the kernel (if relocatable_kernel is true.) - -Field name: relocatable_kernel -Type: read (reloc) -Offset/size: 0x234/1 -Protocol: 2.05+ - - If this field is nonzero, the protected-mode part of the kernel can - be loaded at any address that satisfies the kernel_alignment field. - After loading, the boot loader must set the code32_start field to - point to the loaded code, or to a boot loader hook. - -Field name: cmdline_size -Type: read -Offset/size: 0x238/4 -Protocol: 2.06+ - - The maximum size of the command line without the terminating - zero. This means that the command line can contain at most - cmdline_size characters. With protocol version 2.05 and earlier, the - maximum size was 255. - -Field name: hardware_subarch -Type: write (optional, defaults to x86/PC) -Offset/size: 0x23c/4 -Protocol: 2.07+ - - In a paravirtualized environment the hardware low level architectural - pieces such as interrupt handling, page table handling, and - accessing process control registers needs to be done differently. - - This field allows the bootloader to inform the kernel we are in one - one of those environments. - - 0x00000000 The default x86/PC environment - 0x00000001 lguest - 0x00000002 Xen - -Field name: hardware_subarch_data -Type: write (subarch-dependent) -Offset/size: 0x240/8 -Protocol: 2.07+ - - A pointer to data that is specific to hardware subarch - This field is currently unused for the default x86/PC environment, - do not modify. - -Field name: payload_offset -Type: read -Offset/size: 0x248/4 -Protocol: 2.08+ - - If non-zero then this field contains the offset from the end of the - real-mode code to the payload. - - The payload may be compressed. The format of both the compressed and - uncompressed data should be determined using the standard magic - numbers. Currently only gzip compressed ELF is used. - -Field name: payload_length -Type: read -Offset/size: 0x24c/4 -Protocol: 2.08+ - - The length of the payload. - -Field name: setup_data -Type: write (special) -Offset/size: 0x250/8 -Protocol: 2.09+ - - The 64-bit physical pointer to NULL terminated single linked list of - struct setup_data. This is used to define a more extensible boot - parameters passing mechanism. The definition of struct setup_data is - as follow: - - struct setup_data { - u64 next; - u32 type; - u32 len; - u8 data[0]; - }; - - Where, the next is a 64-bit physical pointer to the next node of - linked list, the next field of the last node is 0; the type is used - to identify the contents of data; the len is the length of data - field; the data holds the real payload. - - This list may be modified at a number of points during the bootup - process. Therefore, when modifying this list one should always make - sure to consider the case where the linked list already contains - entries. - - -**** THE IMAGE CHECKSUM - -From boot protocol version 2.08 onwards the CRC-32 is calculated over -the entire file using the characteristic polynomial 0x04C11DB7 and an -initial remainder of 0xffffffff. The checksum is appended to the -file; therefore the CRC of the file up to the limit specified in the -syssize field of the header is always 0. - - -**** THE KERNEL COMMAND LINE - -The kernel command line has become an important way for the boot -loader to communicate with the kernel. Some of its options are also -relevant to the boot loader itself, see "special command line options" -below. - -The kernel command line is a null-terminated string. The maximum -length can be retrieved from the field cmdline_size. Before protocol -version 2.06, the maximum was 255 characters. A string that is too -long will be automatically truncated by the kernel. - -If the boot protocol version is 2.02 or later, the address of the -kernel command line is given by the header field cmd_line_ptr (see -above.) This address can be anywhere between the end of the setup -heap and 0xA0000. - -If the protocol version is *not* 2.02 or higher, the kernel -command line is entered using the following protocol: - - At offset 0x0020 (word), "cmd_line_magic", enter the magic - number 0xA33F. - - At offset 0x0022 (word), "cmd_line_offset", enter the offset - of the kernel command line (relative to the start of the - real-mode kernel). - - The kernel command line *must* be within the memory region - covered by setup_move_size, so you may need to adjust this - field. - - -**** MEMORY LAYOUT OF THE REAL-MODE CODE - -The real-mode code requires a stack/heap to be set up, as well as -memory allocated for the kernel command line. This needs to be done -in the real-mode accessible memory in bottom megabyte. - -It should be noted that modern machines often have a sizable Extended -BIOS Data Area (EBDA). As a result, it is advisable to use as little -of the low megabyte as possible. - -Unfortunately, under the following circumstances the 0x90000 memory -segment has to be used: - - - When loading a zImage kernel ((loadflags & 0x01) == 0). - - When loading a 2.01 or earlier boot protocol kernel. - - -> For the 2.00 and 2.01 boot protocols, the real-mode code - can be loaded at another address, but it is internally - relocated to 0x90000. For the "old" protocol, the - real-mode code must be loaded at 0x90000. - -When loading at 0x90000, avoid using memory above 0x9a000. - -For boot protocol 2.02 or higher, the command line does not have to be -located in the same 64K segment as the real-mode setup code; it is -thus permitted to give the stack/heap the full 64K segment and locate -the command line above it. - -The kernel command line should not be located below the real-mode -code, nor should it be located in high memory. - - -**** SAMPLE BOOT CONFIGURATION - -As a sample configuration, assume the following layout of the real -mode segment: - - When loading below 0x90000, use the entire segment: - - 0x0000-0x7fff Real mode kernel - 0x8000-0xdfff Stack and heap - 0xe000-0xffff Kernel command line - - When loading at 0x90000 OR the protocol version is 2.01 or earlier: - - 0x0000-0x7fff Real mode kernel - 0x8000-0x97ff Stack and heap - 0x9800-0x9fff Kernel command line - -Such a boot loader should enter the following fields in the header: - - unsigned long base_ptr; /* base address for real-mode segment */ - - if ( setup_sects == 0 ) { - setup_sects = 4; - } - - if ( protocol >= 0x0200 ) { - type_of_loader = ; - if ( loading_initrd ) { - ramdisk_image = ; - ramdisk_size = ; - } - - if ( protocol >= 0x0202 && loadflags & 0x01 ) - heap_end = 0xe000; - else - heap_end = 0x9800; - - if ( protocol >= 0x0201 ) { - heap_end_ptr = heap_end - 0x200; - loadflags |= 0x80; /* CAN_USE_HEAP */ - } - - if ( protocol >= 0x0202 ) { - cmd_line_ptr = base_ptr + heap_end; - strcpy(cmd_line_ptr, cmdline); - } else { - cmd_line_magic = 0xA33F; - cmd_line_offset = heap_end; - setup_move_size = heap_end + strlen(cmdline)+1; - strcpy(base_ptr+cmd_line_offset, cmdline); - } - } else { - /* Very old kernel */ - - heap_end = 0x9800; - - cmd_line_magic = 0xA33F; - cmd_line_offset = heap_end; - - /* A very old kernel MUST have its real-mode code - loaded at 0x90000 */ - - if ( base_ptr != 0x90000 ) { - /* Copy the real-mode kernel */ - memcpy(0x90000, base_ptr, (setup_sects+1)*512); - base_ptr = 0x90000; /* Relocated */ - } - - strcpy(0x90000+cmd_line_offset, cmdline); - - /* It is recommended to clear memory up to the 32K mark */ - memset(0x90000 + (setup_sects+1)*512, 0, - (64-(setup_sects+1))*512); - } - - -**** LOADING THE REST OF THE KERNEL - -The 32-bit (non-real-mode) kernel starts at offset (setup_sects+1)*512 -in the kernel file (again, if setup_sects == 0 the real value is 4.) -It should be loaded at address 0x10000 for Image/zImage kernels and -0x100000 for bzImage kernels. - -The kernel is a bzImage kernel if the protocol >= 2.00 and the 0x01 -bit (LOAD_HIGH) in the loadflags field is set: - - is_bzImage = (protocol >= 0x0200) && (loadflags & 0x01); - load_address = is_bzImage ? 0x100000 : 0x10000; - -Note that Image/zImage kernels can be up to 512K in size, and thus use -the entire 0x10000-0x90000 range of memory. This means it is pretty -much a requirement for these kernels to load the real-mode part at -0x90000. bzImage kernels allow much more flexibility. - - -**** SPECIAL COMMAND LINE OPTIONS - -If the command line provided by the boot loader is entered by the -user, the user may expect the following command line options to work. -They should normally not be deleted from the kernel command line even -though not all of them are actually meaningful to the kernel. Boot -loader authors who need additional command line options for the boot -loader itself should get them registered in -Documentation/kernel-parameters.txt to make sure they will not -conflict with actual kernel options now or in the future. - - vga= - here is either an integer (in C notation, either - decimal, octal, or hexadecimal) or one of the strings - "normal" (meaning 0xFFFF), "ext" (meaning 0xFFFE) or "ask" - (meaning 0xFFFD). This value should be entered into the - vid_mode field, as it is used by the kernel before the command - line is parsed. - - mem= - is an integer in C notation optionally followed by - (case insensitive) K, M, G, T, P or E (meaning << 10, << 20, - << 30, << 40, << 50 or << 60). This specifies the end of - memory to the kernel. This affects the possible placement of - an initrd, since an initrd should be placed near end of - memory. Note that this is an option to *both* the kernel and - the bootloader! - - initrd= - An initrd should be loaded. The meaning of is - obviously bootloader-dependent, and some boot loaders - (e.g. LILO) do not have such a command. - -In addition, some boot loaders add the following options to the -user-specified command line: - - BOOT_IMAGE= - The boot image which was loaded. Again, the meaning of - is obviously bootloader-dependent. - - auto - The kernel was booted without explicit user intervention. - -If these options are added by the boot loader, it is highly -recommended that they are located *first*, before the user-specified -or configuration-specified command line. Otherwise, "init=/bin/sh" -gets confused by the "auto" option. - - -**** RUNNING THE KERNEL - -The kernel is started by jumping to the kernel entry point, which is -located at *segment* offset 0x20 from the start of the real mode -kernel. This means that if you loaded your real-mode kernel code at -0x90000, the kernel entry point is 9020:0000. - -At entry, ds = es = ss should point to the start of the real-mode -kernel code (0x9000 if the code is loaded at 0x90000), sp should be -set up properly, normally pointing to the top of the heap, and -interrupts should be disabled. Furthermore, to guard against bugs in -the kernel, it is recommended that the boot loader sets fs = gs = ds = -es = ss. - -In our example from above, we would do: - - /* Note: in the case of the "old" kernel protocol, base_ptr must - be == 0x90000 at this point; see the previous sample code */ - - seg = base_ptr >> 4; - - cli(); /* Enter with interrupts disabled! */ - - /* Set up the real-mode kernel stack */ - _SS = seg; - _SP = heap_end; - - _DS = _ES = _FS = _GS = seg; - jmp_far(seg+0x20, 0); /* Run the kernel */ - -If your boot sector accesses a floppy drive, it is recommended to -switch off the floppy motor before running the kernel, since the -kernel boot leaves interrupts off and thus the motor will not be -switched off, especially if the loaded kernel has the floppy driver as -a demand-loaded module! - - -**** ADVANCED BOOT LOADER HOOKS - -If the boot loader runs in a particularly hostile environment (such as -LOADLIN, which runs under DOS) it may be impossible to follow the -standard memory location requirements. Such a boot loader may use the -following hooks that, if set, are invoked by the kernel at the -appropriate time. The use of these hooks should probably be -considered an absolutely last resort! - -IMPORTANT: All the hooks are required to preserve %esp, %ebp, %esi and -%edi across invocation. - - realmode_swtch: - A 16-bit real mode far subroutine invoked immediately before - entering protected mode. The default routine disables NMI, so - your routine should probably do so, too. - - code32_start: - A 32-bit flat-mode routine *jumped* to immediately after the - transition to protected mode, but before the kernel is - uncompressed. No segments, except CS, are guaranteed to be - set up (current kernels do, but older ones do not); you should - set them up to BOOT_DS (0x18) yourself. - - After completing your hook, you should jump to the address - that was in this field before your boot loader overwrote it - (relocated, if appropriate.) - - -**** 32-bit BOOT PROTOCOL - -For machine with some new BIOS other than legacy BIOS, such as EFI, -LinuxBIOS, etc, and kexec, the 16-bit real mode setup code in kernel -based on legacy BIOS can not be used, so a 32-bit boot protocol needs -to be defined. - -In 32-bit boot protocol, the first step in loading a Linux kernel -should be to setup the boot parameters (struct boot_params, -traditionally known as "zero page"). The memory for struct boot_params -should be allocated and initialized to all zero. Then the setup header -from offset 0x01f1 of kernel image on should be loaded into struct -boot_params and examined. The end of setup header can be calculated as -follow: - - 0x0202 + byte value at offset 0x0201 - -In addition to read/modify/write the setup header of the struct -boot_params as that of 16-bit boot protocol, the boot loader should -also fill the additional fields of the struct boot_params as that -described in zero-page.txt. - -After setupping the struct boot_params, the boot loader can load the -32/64-bit kernel in the same way as that of 16-bit boot protocol. - -In 32-bit boot protocol, the kernel is started by jumping to the -32-bit kernel entry point, which is the start address of loaded -32/64-bit kernel. - -At entry, the CPU must be in 32-bit protected mode with paging -disabled; a GDT must be loaded with the descriptors for selectors -__BOOT_CS(0x10) and __BOOT_DS(0x18); both descriptors must be 4G flat -segment; __BOOS_CS must have execute/read permission, and __BOOT_DS -must have read/write permission; CS must be __BOOT_CS and DS, ES, SS -must be __BOOT_DS; interrupt must be disabled; %esi must hold the base -address of the struct boot_params; %ebp, %edi and %ebx must be zero. diff --git a/Documentation/x86/i386/usb-legacy-support.txt b/Documentation/x86/i386/usb-legacy-support.txt deleted file mode 100644 index 1894cdfc69d..00000000000 --- a/Documentation/x86/i386/usb-legacy-support.txt +++ /dev/null @@ -1,44 +0,0 @@ -USB Legacy support -~~~~~~~~~~~~~~~~~~ - -Vojtech Pavlik , January 2004 - - -Also known as "USB Keyboard" or "USB Mouse support" in the BIOS Setup is a -feature that allows one to use the USB mouse and keyboard as if they were -their classic PS/2 counterparts. This means one can use an USB keyboard to -type in LILO for example. - -It has several drawbacks, though: - -1) On some machines, the emulated PS/2 mouse takes over even when no USB - mouse is present and a real PS/2 mouse is present. In that case the extra - features (wheel, extra buttons, touchpad mode) of the real PS/2 mouse may - not be available. - -2) If CONFIG_HIGHMEM64G is enabled, the PS/2 mouse emulation can cause - system crashes, because the SMM BIOS is not expecting to be in PAE mode. - The Intel E7505 is a typical machine where this happens. - -3) If AMD64 64-bit mode is enabled, again system crashes often happen, - because the SMM BIOS isn't expecting the CPU to be in 64-bit mode. The - BIOS manufacturers only test with Windows, and Windows doesn't do 64-bit - yet. - -Solutions: - -Problem 1) can be solved by loading the USB drivers prior to loading the -PS/2 mouse driver. Since the PS/2 mouse driver is in 2.6 compiled into -the kernel unconditionally, this means the USB drivers need to be -compiled-in, too. - -Problem 2) can currently only be solved by either disabling HIGHMEM64G -in the kernel config or USB Legacy support in the BIOS. A BIOS update -could help, but so far no such update exists. - -Problem 3) is usually fixed by a BIOS update. Check the board -manufacturers web site. If an update is not available, disable USB -Legacy support in the BIOS. If this alone doesn't help, try also adding -idle=poll on the kernel command line. The BIOS may be entering the SMM -on the HLT instruction as well. - diff --git a/Documentation/x86/i386/zero-page.txt b/Documentation/x86/i386/zero-page.txt deleted file mode 100644 index 169ad423a3d..00000000000 --- a/Documentation/x86/i386/zero-page.txt +++ /dev/null @@ -1,31 +0,0 @@ -The additional fields in struct boot_params as a part of 32-bit boot -protocol of kernel. These should be filled by bootloader or 16-bit -real-mode setup code of the kernel. References/settings to it mainly -are in: - - include/asm-x86/bootparam.h - - -Offset Proto Name Meaning -/Size - -000/040 ALL screen_info Text mode or frame buffer information - (struct screen_info) -040/014 ALL apm_bios_info APM BIOS information (struct apm_bios_info) -060/010 ALL ist_info Intel SpeedStep (IST) BIOS support information - (struct ist_info) -080/010 ALL hd0_info hd0 disk parameter, OBSOLETE!! -090/010 ALL hd1_info hd1 disk parameter, OBSOLETE!! -0A0/010 ALL sys_desc_table System description table (struct sys_desc_table) -140/080 ALL edid_info Video mode setup (struct edid_info) -1C0/020 ALL efi_info EFI 32 information (struct efi_info) -1E0/004 ALL alk_mem_k Alternative mem check, in KB -1E4/004 ALL scratch Scratch field for the kernel setup code -1E8/001 ALL e820_entries Number of entries in e820_map (below) -1E9/001 ALL eddbuf_entries Number of entries in eddbuf (below) -1EA/001 ALL edd_mbr_sig_buf_entries Number of entries in edd_mbr_sig_buffer - (below) -290/040 ALL edd_mbr_sig_buffer EDD MBR signatures -2D0/A00 ALL e820_map E820 memory map table - (array of struct e820entry) -D00/1EC ALL eddbuf EDD data (array of struct edd_info) diff --git a/Documentation/x86/usb-legacy-support.txt b/Documentation/x86/usb-legacy-support.txt new file mode 100644 index 00000000000..1894cdfc69d --- /dev/null +++ b/Documentation/x86/usb-legacy-support.txt @@ -0,0 +1,44 @@ +USB Legacy support +~~~~~~~~~~~~~~~~~~ + +Vojtech Pavlik , January 2004 + + +Also known as "USB Keyboard" or "USB Mouse support" in the BIOS Setup is a +feature that allows one to use the USB mouse and keyboard as if they were +their classic PS/2 counterparts. This means one can use an USB keyboard to +type in LILO for example. + +It has several drawbacks, though: + +1) On some machines, the emulated PS/2 mouse takes over even when no USB + mouse is present and a real PS/2 mouse is present. In that case the extra + features (wheel, extra buttons, touchpad mode) of the real PS/2 mouse may + not be available. + +2) If CONFIG_HIGHMEM64G is enabled, the PS/2 mouse emulation can cause + system crashes, because the SMM BIOS is not expecting to be in PAE mode. + The Intel E7505 is a typical machine where this happens. + +3) If AMD64 64-bit mode is enabled, again system crashes often happen, + because the SMM BIOS isn't expecting the CPU to be in 64-bit mode. The + BIOS manufacturers only test with Windows, and Windows doesn't do 64-bit + yet. + +Solutions: + +Problem 1) can be solved by loading the USB drivers prior to loading the +PS/2 mouse driver. Since the PS/2 mouse driver is in 2.6 compiled into +the kernel unconditionally, this means the USB drivers need to be +compiled-in, too. + +Problem 2) can currently only be solved by either disabling HIGHMEM64G +in the kernel config or USB Legacy support in the BIOS. A BIOS update +could help, but so far no such update exists. + +Problem 3) is usually fixed by a BIOS update. Check the board +manufacturers web site. If an update is not available, disable USB +Legacy support in the BIOS. If this alone doesn't help, try also adding +idle=poll on the kernel command line. The BIOS may be entering the SMM +on the HLT instruction as well. + diff --git a/Documentation/x86/zero-page.txt b/Documentation/x86/zero-page.txt new file mode 100644 index 00000000000..169ad423a3d --- /dev/null +++ b/Documentation/x86/zero-page.txt @@ -0,0 +1,31 @@ +The additional fields in struct boot_params as a part of 32-bit boot +protocol of kernel. These should be filled by bootloader or 16-bit +real-mode setup code of the kernel. References/settings to it mainly +are in: + + include/asm-x86/bootparam.h + + +Offset Proto Name Meaning +/Size + +000/040 ALL screen_info Text mode or frame buffer information + (struct screen_info) +040/014 ALL apm_bios_info APM BIOS information (struct apm_bios_info) +060/010 ALL ist_info Intel SpeedStep (IST) BIOS support information + (struct ist_info) +080/010 ALL hd0_info hd0 disk parameter, OBSOLETE!! +090/010 ALL hd1_info hd1 disk parameter, OBSOLETE!! +0A0/010 ALL sys_desc_table System description table (struct sys_desc_table) +140/080 ALL edid_info Video mode setup (struct edid_info) +1C0/020 ALL efi_info EFI 32 information (struct efi_info) +1E0/004 ALL alk_mem_k Alternative mem check, in KB +1E4/004 ALL scratch Scratch field for the kernel setup code +1E8/001 ALL e820_entries Number of entries in e820_map (below) +1E9/001 ALL eddbuf_entries Number of entries in eddbuf (below) +1EA/001 ALL edd_mbr_sig_buf_entries Number of entries in edd_mbr_sig_buffer + (below) +290/040 ALL edd_mbr_sig_buffer EDD MBR signatures +2D0/A00 ALL e820_map E820 memory map table + (array of struct e820entry) +D00/1EC ALL eddbuf EDD data (array of struct edd_info) -- cgit v1.2.3 From a021e5124a6c57325ffb02a60cd1d5f40342f8aa Mon Sep 17 00:00:00 2001 From: "H. Peter Anvin" Date: Tue, 22 Jul 2008 15:33:57 -0400 Subject: x86: doc: boot.txt: fix the size of the start_sys field The start_sys field is two bytes, not four. Signed-off-by: H. Peter Anvin --- Documentation/x86/boot.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'Documentation') diff --git a/Documentation/x86/boot.txt b/Documentation/x86/boot.txt index 147bfe511cd..83c0033ee9e 100644 --- a/Documentation/x86/boot.txt +++ b/Documentation/x86/boot.txt @@ -308,7 +308,7 @@ Protocol: 2.00+ Field name: start_sys Type: read -Offset/size: 0x20c/4 +Offset/size: 0x20c/2 Protocol: 2.00+ The load low segment (0x1000). Obsolete. -- cgit v1.2.3 From 7225e75144b9718cbbe1820d9c011c809d5773fd Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Sat, 26 Jul 2008 17:54:22 -0700 Subject: documentation: move mtrr.txt to Doc/x86/ subdir Move mtrr.txt to the Documentation/x86/ subdirectory. Add 00-INDEX to the Documentation/x86/ subdirectory. Signed-off-by: Randy Dunlap Cc: Adrian Bunk Signed-off-by: Ingo Molnar --- Documentation/00-INDEX | 2 - Documentation/mtrr.txt | 305 --------------------------------------------- Documentation/x86/00-INDEX | 4 + Documentation/x86/mtrr.txt | 305 +++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 309 insertions(+), 307 deletions(-) delete mode 100644 Documentation/mtrr.txt create mode 100644 Documentation/x86/00-INDEX create mode 100644 Documentation/x86/mtrr.txt (limited to 'Documentation') diff --git a/Documentation/00-INDEX b/Documentation/00-INDEX index 1977fab3865..661b6ccfe18 100644 --- a/Documentation/00-INDEX +++ b/Documentation/00-INDEX @@ -253,8 +253,6 @@ mono.txt - how to execute Mono-based .NET binaries with the help of BINFMT_MISC. moxa-smartio - file with info on installing/using Moxa multiport serial driver. -mtrr.txt - - how to use PPro Memory Type Range Registers to increase performance. mutex-design.txt - info on the generic mutex subsystem. namespaces/ diff --git a/Documentation/mtrr.txt b/Documentation/mtrr.txt deleted file mode 100644 index c39ac395970..00000000000 --- a/Documentation/mtrr.txt +++ /dev/null @@ -1,305 +0,0 @@ -MTRR (Memory Type Range Register) control -3 Jun 1999 -Richard Gooch - - - On Intel P6 family processors (Pentium Pro, Pentium II and later) - the Memory Type Range Registers (MTRRs) may be used to control - processor access to memory ranges. This is most useful when you have - a video (VGA) card on a PCI or AGP bus. Enabling write-combining - allows bus write transfers to be combined into a larger transfer - before bursting over the PCI/AGP bus. This can increase performance - of image write operations 2.5 times or more. - - The Cyrix 6x86, 6x86MX and M II processors have Address Range - Registers (ARRs) which provide a similar functionality to MTRRs. For - these, the ARRs are used to emulate the MTRRs. - - The AMD K6-2 (stepping 8 and above) and K6-3 processors have two - MTRRs. These are supported. The AMD Athlon family provide 8 Intel - style MTRRs. - - The Centaur C6 (WinChip) has 8 MCRs, allowing write-combining. These - are supported. - - The VIA Cyrix III and VIA C3 CPUs offer 8 Intel style MTRRs. - - The CONFIG_MTRR option creates a /proc/mtrr file which may be used - to manipulate your MTRRs. Typically the X server should use - this. This should have a reasonably generic interface so that - similar control registers on other processors can be easily - supported. - - -There are two interfaces to /proc/mtrr: one is an ASCII interface -which allows you to read and write. The other is an ioctl() -interface. The ASCII interface is meant for administration. The -ioctl() interface is meant for C programs (i.e. the X server). The -interfaces are described below, with sample commands and C code. - -=============================================================================== -Reading MTRRs from the shell: - -% cat /proc/mtrr -reg00: base=0x00000000 ( 0MB), size= 128MB: write-back, count=1 -reg01: base=0x08000000 ( 128MB), size= 64MB: write-back, count=1 -=============================================================================== -Creating MTRRs from the C-shell: -# echo "base=0xf8000000 size=0x400000 type=write-combining" >! /proc/mtrr -or if you use bash: -# echo "base=0xf8000000 size=0x400000 type=write-combining" >| /proc/mtrr - -And the result thereof: -% cat /proc/mtrr -reg00: base=0x00000000 ( 0MB), size= 128MB: write-back, count=1 -reg01: base=0x08000000 ( 128MB), size= 64MB: write-back, count=1 -reg02: base=0xf8000000 (3968MB), size= 4MB: write-combining, count=1 - -This is for video RAM at base address 0xf8000000 and size 4 megabytes. To -find out your base address, you need to look at the output of your X -server, which tells you where the linear framebuffer address is. A -typical line that you may get is: - -(--) S3: PCI: 968 rev 0, Linear FB @ 0xf8000000 - -Note that you should only use the value from the X server, as it may -move the framebuffer base address, so the only value you can trust is -that reported by the X server. - -To find out the size of your framebuffer (what, you don't actually -know?), the following line will tell you: - -(--) S3: videoram: 4096k - -That's 4 megabytes, which is 0x400000 bytes (in hexadecimal). -A patch is being written for XFree86 which will make this automatic: -in other words the X server will manipulate /proc/mtrr using the -ioctl() interface, so users won't have to do anything. If you use a -commercial X server, lobby your vendor to add support for MTRRs. -=============================================================================== -Creating overlapping MTRRs: - -%echo "base=0xfb000000 size=0x1000000 type=write-combining" >/proc/mtrr -%echo "base=0xfb000000 size=0x1000 type=uncachable" >/proc/mtrr - -And the results: cat /proc/mtrr -reg00: base=0x00000000 ( 0MB), size= 64MB: write-back, count=1 -reg01: base=0xfb000000 (4016MB), size= 16MB: write-combining, count=1 -reg02: base=0xfb000000 (4016MB), size= 4kB: uncachable, count=1 - -Some cards (especially Voodoo Graphics boards) need this 4 kB area -excluded from the beginning of the region because it is used for -registers. - -NOTE: You can only create type=uncachable region, if the first -region that you created is type=write-combining. -=============================================================================== -Removing MTRRs from the C-shell: -% echo "disable=2" >! /proc/mtrr -or using bash: -% echo "disable=2" >| /proc/mtrr -=============================================================================== -Reading MTRRs from a C program using ioctl()'s: - -/* mtrr-show.c - - Source file for mtrr-show (example program to show MTRRs using ioctl()'s) - - Copyright (C) 1997-1998 Richard Gooch - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - - Richard Gooch may be reached by email at rgooch@atnf.csiro.au - The postal address is: - Richard Gooch, c/o ATNF, P. O. Box 76, Epping, N.S.W., 2121, Australia. -*/ - -/* - This program will use an ioctl() on /proc/mtrr to show the current MTRR - settings. This is an alternative to reading /proc/mtrr. - - - Written by Richard Gooch 17-DEC-1997 - - Last updated by Richard Gooch 2-MAY-1998 - - -*/ -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#define TRUE 1 -#define FALSE 0 -#define ERRSTRING strerror (errno) - -static char *mtrr_strings[MTRR_NUM_TYPES] = -{ - "uncachable", /* 0 */ - "write-combining", /* 1 */ - "?", /* 2 */ - "?", /* 3 */ - "write-through", /* 4 */ - "write-protect", /* 5 */ - "write-back", /* 6 */ -}; - -int main () -{ - int fd; - struct mtrr_gentry gentry; - - if ( ( fd = open ("/proc/mtrr", O_RDONLY, 0) ) == -1 ) - { - if (errno == ENOENT) - { - fputs ("/proc/mtrr not found: not supported or you don't have a PPro?\n", - stderr); - exit (1); - } - fprintf (stderr, "Error opening /proc/mtrr\t%s\n", ERRSTRING); - exit (2); - } - for (gentry.regnum = 0; ioctl (fd, MTRRIOC_GET_ENTRY, &gentry) == 0; - ++gentry.regnum) - { - if (gentry.size < 1) - { - fprintf (stderr, "Register: %u disabled\n", gentry.regnum); - continue; - } - fprintf (stderr, "Register: %u base: 0x%lx size: 0x%lx type: %s\n", - gentry.regnum, gentry.base, gentry.size, - mtrr_strings[gentry.type]); - } - if (errno == EINVAL) exit (0); - fprintf (stderr, "Error doing ioctl(2) on /dev/mtrr\t%s\n", ERRSTRING); - exit (3); -} /* End Function main */ -=============================================================================== -Creating MTRRs from a C programme using ioctl()'s: - -/* mtrr-add.c - - Source file for mtrr-add (example programme to add an MTRRs using ioctl()) - - Copyright (C) 1997-1998 Richard Gooch - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - - Richard Gooch may be reached by email at rgooch@atnf.csiro.au - The postal address is: - Richard Gooch, c/o ATNF, P. O. Box 76, Epping, N.S.W., 2121, Australia. -*/ - -/* - This programme will use an ioctl() on /proc/mtrr to add an entry. The first - available mtrr is used. This is an alternative to writing /proc/mtrr. - - - Written by Richard Gooch 17-DEC-1997 - - Last updated by Richard Gooch 2-MAY-1998 - - -*/ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#define TRUE 1 -#define FALSE 0 -#define ERRSTRING strerror (errno) - -static char *mtrr_strings[MTRR_NUM_TYPES] = -{ - "uncachable", /* 0 */ - "write-combining", /* 1 */ - "?", /* 2 */ - "?", /* 3 */ - "write-through", /* 4 */ - "write-protect", /* 5 */ - "write-back", /* 6 */ -}; - -int main (int argc, char **argv) -{ - int fd; - struct mtrr_sentry sentry; - - if (argc != 4) - { - fprintf (stderr, "Usage:\tmtrr-add base size type\n"); - exit (1); - } - sentry.base = strtoul (argv[1], NULL, 0); - sentry.size = strtoul (argv[2], NULL, 0); - for (sentry.type = 0; sentry.type < MTRR_NUM_TYPES; ++sentry.type) - { - if (strcmp (argv[3], mtrr_strings[sentry.type]) == 0) break; - } - if (sentry.type >= MTRR_NUM_TYPES) - { - fprintf (stderr, "Illegal type: \"%s\"\n", argv[3]); - exit (2); - } - if ( ( fd = open ("/proc/mtrr", O_WRONLY, 0) ) == -1 ) - { - if (errno == ENOENT) - { - fputs ("/proc/mtrr not found: not supported or you don't have a PPro?\n", - stderr); - exit (3); - } - fprintf (stderr, "Error opening /proc/mtrr\t%s\n", ERRSTRING); - exit (4); - } - if (ioctl (fd, MTRRIOC_ADD_ENTRY, &sentry) == -1) - { - fprintf (stderr, "Error doing ioctl(2) on /dev/mtrr\t%s\n", ERRSTRING); - exit (5); - } - fprintf (stderr, "Sleeping for 5 seconds so you can see the new entry\n"); - sleep (5); - close (fd); - fputs ("I've just closed /proc/mtrr so now the new entry should be gone\n", - stderr); -} /* End Function main */ -=============================================================================== diff --git a/Documentation/x86/00-INDEX b/Documentation/x86/00-INDEX new file mode 100644 index 00000000000..dbe3377754a --- /dev/null +++ b/Documentation/x86/00-INDEX @@ -0,0 +1,4 @@ +00-INDEX + - this file +mtrr.txt + - how to use x86 Memory Type Range Registers to increase performance diff --git a/Documentation/x86/mtrr.txt b/Documentation/x86/mtrr.txt new file mode 100644 index 00000000000..cc071dc333c --- /dev/null +++ b/Documentation/x86/mtrr.txt @@ -0,0 +1,305 @@ +MTRR (Memory Type Range Register) control +3 Jun 1999 +Richard Gooch + + + On Intel P6 family processors (Pentium Pro, Pentium II and later) + the Memory Type Range Registers (MTRRs) may be used to control + processor access to memory ranges. This is most useful when you have + a video (VGA) card on a PCI or AGP bus. Enabling write-combining + allows bus write transfers to be combined into a larger transfer + before bursting over the PCI/AGP bus. This can increase performance + of image write operations 2.5 times or more. + + The Cyrix 6x86, 6x86MX and M II processors have Address Range + Registers (ARRs) which provide a similar functionality to MTRRs. For + these, the ARRs are used to emulate the MTRRs. + + The AMD K6-2 (stepping 8 and above) and K6-3 processors have two + MTRRs. These are supported. The AMD Athlon family provide 8 Intel + style MTRRs. + + The Centaur C6 (WinChip) has 8 MCRs, allowing write-combining. These + are supported. + + The VIA Cyrix III and VIA C3 CPUs offer 8 Intel style MTRRs. + + The CONFIG_MTRR option creates a /proc/mtrr file which may be used + to manipulate your MTRRs. Typically the X server should use + this. This should have a reasonably generic interface so that + similar control registers on other processors can be easily + supported. + + +There are two interfaces to /proc/mtrr: one is an ASCII interface +which allows you to read and write. The other is an ioctl() +interface. The ASCII interface is meant for administration. The +ioctl() interface is meant for C programs (i.e. the X server). The +interfaces are described below, with sample commands and C code. + +=============================================================================== +Reading MTRRs from the shell: + +% cat /proc/mtrr +reg00: base=0x00000000 ( 0MB), size= 128MB: write-back, count=1 +reg01: base=0x08000000 ( 128MB), size= 64MB: write-back, count=1 +=============================================================================== +Creating MTRRs from the C-shell: +# echo "base=0xf8000000 size=0x400000 type=write-combining" >! /proc/mtrr +or if you use bash: +# echo "base=0xf8000000 size=0x400000 type=write-combining" >| /proc/mtrr + +And the result thereof: +% cat /proc/mtrr +reg00: base=0x00000000 ( 0MB), size= 128MB: write-back, count=1 +reg01: base=0x08000000 ( 128MB), size= 64MB: write-back, count=1 +reg02: base=0xf8000000 (3968MB), size= 4MB: write-combining, count=1 + +This is for video RAM at base address 0xf8000000 and size 4 megabytes. To +find out your base address, you need to look at the output of your X +server, which tells you where the linear framebuffer address is. A +typical line that you may get is: + +(--) S3: PCI: 968 rev 0, Linear FB @ 0xf8000000 + +Note that you should only use the value from the X server, as it may +move the framebuffer base address, so the only value you can trust is +that reported by the X server. + +To find out the size of your framebuffer (what, you don't actually +know?), the following line will tell you: + +(--) S3: videoram: 4096k + +That's 4 megabytes, which is 0x400000 bytes (in hexadecimal). +A patch is being written for XFree86 which will make this automatic: +in other words the X server will manipulate /proc/mtrr using the +ioctl() interface, so users won't have to do anything. If you use a +commercial X server, lobby your vendor to add support for MTRRs. +=============================================================================== +Creating overlapping MTRRs: + +%echo "base=0xfb000000 size=0x1000000 type=write-combining" >/proc/mtrr +%echo "base=0xfb000000 size=0x1000 type=uncachable" >/proc/mtrr + +And the results: cat /proc/mtrr +reg00: base=0x00000000 ( 0MB), size= 64MB: write-back, count=1 +reg01: base=0xfb000000 (4016MB), size= 16MB: write-combining, count=1 +reg02: base=0xfb000000 (4016MB), size= 4kB: uncachable, count=1 + +Some cards (especially Voodoo Graphics boards) need this 4 kB area +excluded from the beginning of the region because it is used for +registers. + +NOTE: You can only create type=uncachable region, if the first +region that you created is type=write-combining. +=============================================================================== +Removing MTRRs from the C-shell: +% echo "disable=2" >! /proc/mtrr +or using bash: +% echo "disable=2" >| /proc/mtrr +=============================================================================== +Reading MTRRs from a C program using ioctl()'s: + +/* mtrr-show.c + + Source file for mtrr-show (example program to show MTRRs using ioctl()'s) + + Copyright (C) 1997-1998 Richard Gooch + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + + Richard Gooch may be reached by email at rgooch@atnf.csiro.au + The postal address is: + Richard Gooch, c/o ATNF, P. O. Box 76, Epping, N.S.W., 2121, Australia. +*/ + +/* + This program will use an ioctl() on /proc/mtrr to show the current MTRR + settings. This is an alternative to reading /proc/mtrr. + + + Written by Richard Gooch 17-DEC-1997 + + Last updated by Richard Gooch 2-MAY-1998 + + +*/ +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define TRUE 1 +#define FALSE 0 +#define ERRSTRING strerror (errno) + +static char *mtrr_strings[MTRR_NUM_TYPES] = +{ + "uncachable", /* 0 */ + "write-combining", /* 1 */ + "?", /* 2 */ + "?", /* 3 */ + "write-through", /* 4 */ + "write-protect", /* 5 */ + "write-back", /* 6 */ +}; + +int main () +{ + int fd; + struct mtrr_gentry gentry; + + if ( ( fd = open ("/proc/mtrr", O_RDONLY, 0) ) == -1 ) + { + if (errno == ENOENT) + { + fputs ("/proc/mtrr not found: not supported or you don't have a PPro?\n", + stderr); + exit (1); + } + fprintf (stderr, "Error opening /proc/mtrr\t%s\n", ERRSTRING); + exit (2); + } + for (gentry.regnum = 0; ioctl (fd, MTRRIOC_GET_ENTRY, &gentry) == 0; + ++gentry.regnum) + { + if (gentry.size < 1) + { + fprintf (stderr, "Register: %u disabled\n", gentry.regnum); + continue; + } + fprintf (stderr, "Register: %u base: 0x%lx size: 0x%lx type: %s\n", + gentry.regnum, gentry.base, gentry.size, + mtrr_strings[gentry.type]); + } + if (errno == EINVAL) exit (0); + fprintf (stderr, "Error doing ioctl(2) on /dev/mtrr\t%s\n", ERRSTRING); + exit (3); +} /* End Function main */ +=============================================================================== +Creating MTRRs from a C programme using ioctl()'s: + +/* mtrr-add.c + + Source file for mtrr-add (example programme to add an MTRRs using ioctl()) + + Copyright (C) 1997-1998 Richard Gooch + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + + Richard Gooch may be reached by email at rgooch@atnf.csiro.au + The postal address is: + Richard Gooch, c/o ATNF, P. O. Box 76, Epping, N.S.W., 2121, Australia. +*/ + +/* + This programme will use an ioctl() on /proc/mtrr to add an entry. The first + available mtrr is used. This is an alternative to writing /proc/mtrr. + + + Written by Richard Gooch 17-DEC-1997 + + Last updated by Richard Gooch 2-MAY-1998 + + +*/ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define TRUE 1 +#define FALSE 0 +#define ERRSTRING strerror (errno) + +static char *mtrr_strings[MTRR_NUM_TYPES] = +{ + "uncachable", /* 0 */ + "write-combining", /* 1 */ + "?", /* 2 */ + "?", /* 3 */ + "write-through", /* 4 */ + "write-protect", /* 5 */ + "write-back", /* 6 */ +}; + +int main (int argc, char **argv) +{ + int fd; + struct mtrr_sentry sentry; + + if (argc != 4) + { + fprintf (stderr, "Usage:\tmtrr-add base size type\n"); + exit (1); + } + sentry.base = strtoul (argv[1], NULL, 0); + sentry.size = strtoul (argv[2], NULL, 0); + for (sentry.type = 0; sentry.type < MTRR_NUM_TYPES; ++sentry.type) + { + if (strcmp (argv[3], mtrr_strings[sentry.type]) == 0) break; + } + if (sentry.type >= MTRR_NUM_TYPES) + { + fprintf (stderr, "Illegal type: \"%s\"\n", argv[3]); + exit (2); + } + if ( ( fd = open ("/proc/mtrr", O_WRONLY, 0) ) == -1 ) + { + if (errno == ENOENT) + { + fputs ("/proc/mtrr not found: not supported or you don't have a PPro?\n", + stderr); + exit (3); + } + fprintf (stderr, "Error opening /proc/mtrr\t%s\n", ERRSTRING); + exit (4); + } + if (ioctl (fd, MTRRIOC_ADD_ENTRY, &sentry) == -1) + { + fprintf (stderr, "Error doing ioctl(2) on /dev/mtrr\t%s\n", ERRSTRING); + exit (5); + } + fprintf (stderr, "Sleeping for 5 seconds so you can see the new entry\n"); + sleep (5); + close (fd); + fputs ("I've just closed /proc/mtrr so now the new entry should be gone\n", + stderr); +} /* End Function main */ +=============================================================================== -- cgit v1.2.3 From 59dfc3f8fbabb8681ab4f2fb2df795f9211f40f9 Mon Sep 17 00:00:00 2001 From: "venkatesh.pallipadi@intel.com" Date: Wed, 20 Aug 2008 16:45:54 -0700 Subject: x86: PAT documentation updates with debug info Documentation update for PAT. Reflect the latest API details. Also, adds details about ways to get more info in order to debug PAT. Signed-off-by: Venkatesh Pallipadi Signed-off-by: Ingo Molnar --- Documentation/x86/pat.txt | 54 +++++++++++++++++++++++++++++++++++++++-------- 1 file changed, 45 insertions(+), 9 deletions(-) (limited to 'Documentation') diff --git a/Documentation/x86/pat.txt b/Documentation/x86/pat.txt index 17965f927c1..c93ff5f4c0d 100644 --- a/Documentation/x86/pat.txt +++ b/Documentation/x86/pat.txt @@ -14,6 +14,10 @@ PAT allows for different types of memory attributes. The most commonly used ones that will be supported at this time are Write-back, Uncached, Write-combined and Uncached Minus. + +PAT APIs +-------- + There are many different APIs in the kernel that allows setting of memory attributes at the page level. In order to avoid aliasing, these interfaces should be used thoughtfully. Below is a table of interfaces available, @@ -26,38 +30,38 @@ address range to avoid any aliasing. API | RAM | ACPI,... | Reserved/Holes | -----------------------|----------|------------|------------------| | | | | -ioremap | -- | UC | UC | +ioremap | -- | UC- | UC- | | | | | ioremap_cache | -- | WB | WB | | | | | -ioremap_nocache | -- | UC | UC | +ioremap_nocache | -- | UC- | UC- | | | | | ioremap_wc | -- | -- | WC | | | | | -set_memory_uc | UC | -- | -- | +set_memory_uc | UC- | -- | -- | set_memory_wb | | | | | | | | set_memory_wc | WC | -- | -- | set_memory_wb | | | | | | | | -pci sysfs resource | -- | -- | UC | +pci sysfs resource | -- | -- | UC- | | | | | pci sysfs resource_wc | -- | -- | WC | is IORESOURCE_PREFETCH| | | | | | | | -pci proc | -- | -- | UC | +pci proc | -- | -- | UC- | !PCIIOC_WRITE_COMBINE | | | | | | | | pci proc | -- | -- | WC | PCIIOC_WRITE_COMBINE | | | | | | | | -/dev/mem | -- | UC | UC | +/dev/mem | -- | WB/WC/UC- | WB/WC/UC- | read-write | | | | | | | | -/dev/mem | -- | UC | UC | +/dev/mem | -- | UC- | UC- | mmap SYNC flag | | | | | | | | -/dev/mem | -- | WB/WC/UC | WB/WC/UC | +/dev/mem | -- | WB/WC/UC- | WB/WC/UC- | mmap !SYNC flag | |(from exist-| (from exist- | and | | ing alias)| ing alias) | any alias to this area| | | | @@ -68,7 +72,7 @@ pci proc | -- | -- | WC | and | | | | MTRR says WB | | | | | | | | -/dev/mem | -- | -- | UC_MINUS | +/dev/mem | -- | -- | UC- | mmap !SYNC flag | | | | no alias to this area | | | | and | | | | @@ -98,3 +102,35 @@ types. Drivers should use set_memory_[uc|wc] to set access type for RAM ranges. + +PAT debugging +------------- + +With CONFIG_DEBUG_FS enabled, PAT memtype list can be examined by + +# mount -t debugfs debugfs /sys/kernel/debug +# cat /sys/kernel/debug/x86/pat_memtype_list +PAT memtype list: +uncached-minus @ 0x7fadf000-0x7fae0000 +uncached-minus @ 0x7fb19000-0x7fb1a000 +uncached-minus @ 0x7fb1a000-0x7fb1b000 +uncached-minus @ 0x7fb1b000-0x7fb1c000 +uncached-minus @ 0x7fb1c000-0x7fb1d000 +uncached-minus @ 0x7fb1d000-0x7fb1e000 +uncached-minus @ 0x7fb1e000-0x7fb25000 +uncached-minus @ 0x7fb25000-0x7fb26000 +uncached-minus @ 0x7fb26000-0x7fb27000 +uncached-minus @ 0x7fb27000-0x7fb28000 +uncached-minus @ 0x7fb28000-0x7fb2e000 +uncached-minus @ 0x7fb2e000-0x7fb2f000 +uncached-minus @ 0x7fb2f000-0x7fb30000 +uncached-minus @ 0x7fb31000-0x7fb32000 +uncached-minus @ 0x80000000-0x90000000 + +This list shows physical address ranges and various PAT settings used to +access those physical address ranges. + +Another, more verbose way of getting PAT related debug messages is with +"debugpat" boot parameter. With this parameter, various debug messages are +printed to dmesg log. + -- cgit v1.2.3 From b05f78f5c713eda2c34e495d92495ee4f1c3b5e1 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Fri, 22 Aug 2008 01:32:50 -0700 Subject: x86_64: printout msr -v2 commandline show_msr=1 for bsp, show_msr=32 for all 32 cpus. [ mingo@elte.hu: added documentation ] Signed-off-by: Yinghai Lu Signed-off-by: Ingo Molnar --- Documentation/kernel-parameters.txt | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'Documentation') diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 47e7d8794fc..8679e80b9fc 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1852,6 +1852,12 @@ and is between 256 and 4096 characters. It is defined in the file shapers= [NET] Maximal number of shapers. + show_msr= [x86] show boot-time MSR settings + Format: { } + Show boot-time (BIOS-initialized) MSR settings. + The parameter means the number of CPUs to show, + for example 1 means boot CPU only. + sim710= [SCSI,HW] See header of drivers/scsi/sim710.c. -- cgit v1.2.3 From 1befdefcf476d5eb2fb4243fdf4d996a376708b1 Mon Sep 17 00:00:00 2001 From: "Luiz Fernando N. Capitulino" Date: Thu, 28 Aug 2008 11:00:07 -0300 Subject: x86: remove 8254 timer texts from Documentation Commit ecd29476ae0143b1c3641edfa76c0fc3e9ad3021 removed the "disable_8254_timer" and "enable_8254_timer" kernel parameters from the kernel but did not remove the references to them from two files in the Documentation directory: kernel-parameters.txt and x86/x86_64/boot-options.txt. This change completes the removal. Signed-off-by: Luiz Fernando N. Capitulino Acked-by: Maciej W. Rozycki Signed-off-by: Ingo Molnar --- Documentation/kernel-parameters.txt | 6 ------ Documentation/x86/x86_64/boot-options.txt | 4 ---- 2 files changed, 10 deletions(-) (limited to 'Documentation') diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index a8976467a98..53b0a8f5b23 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -463,12 +463,6 @@ and is between 256 and 4096 characters. It is defined in the file Range: 0 - 8192 Default: 64 - disable_8254_timer - enable_8254_timer - [IA32/X86_64] Disable/Enable interrupt 0 timer routing - over the 8254 in addition to over the IO-APIC. The - kernel tries to set a sensible default. - hpet= [X86-32,HPET] option to control HPET usage Format: { enable (default) | disable | force } disable: disable HPET and use PIT instead diff --git a/Documentation/x86/x86_64/boot-options.txt b/Documentation/x86/x86_64/boot-options.txt index b0c7b6c4abd..72ffb5373ec 100644 --- a/Documentation/x86/x86_64/boot-options.txt +++ b/Documentation/x86/x86_64/boot-options.txt @@ -54,10 +54,6 @@ APICs apicmaintimer. Useful when your PIT timer is totally broken. - disable_8254_timer / enable_8254_timer - Enable interrupt 0 timer routing over the 8254 in addition to over - the IO-APIC. The kernel tries to set a sensible default. - Early Console syntax: earlyprintk=vga -- cgit v1.2.3