From f546c65cd59275c7b95eba4f9b3ab83b38a5e9cb Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 4 Oct 2009 22:53:40 +0200 Subject: i2c: Move misc devices documentation Some times ago the eeprom and max6875 drivers moved to drivers/misc/eeprom, but their documentation did not follow. It's finally time to get rid of Documentation/i2c/chips. Signed-off-by: Jean Delvare Cc: Ben Gardner Acked-by: Wolfram Sang --- Documentation/i2c/chips/eeprom | 96 --------------------------------- Documentation/i2c/chips/max6875 | 108 ------------------------------------- Documentation/misc-devices/eeprom | 96 +++++++++++++++++++++++++++++++++ Documentation/misc-devices/max6875 | 108 +++++++++++++++++++++++++++++++++++++ 4 files changed, 204 insertions(+), 204 deletions(-) delete mode 100644 Documentation/i2c/chips/eeprom delete mode 100644 Documentation/i2c/chips/max6875 create mode 100644 Documentation/misc-devices/eeprom create mode 100644 Documentation/misc-devices/max6875 diff --git a/Documentation/i2c/chips/eeprom b/Documentation/i2c/chips/eeprom deleted file mode 100644 index f7e8104b576..00000000000 --- a/Documentation/i2c/chips/eeprom +++ /dev/null @@ -1,96 +0,0 @@ -Kernel driver eeprom -==================== - -Supported chips: - * Any EEPROM chip in the designated address range - Prefix: 'eeprom' - Addresses scanned: I2C 0x50 - 0x57 - Datasheets: Publicly available from: - Atmel (www.atmel.com), - Catalyst (www.catsemi.com), - Fairchild (www.fairchildsemi.com), - Microchip (www.microchip.com), - Philips (www.semiconductor.philips.com), - Rohm (www.rohm.com), - ST (www.st.com), - Xicor (www.xicor.com), - and others. - - Chip Size (bits) Address - 24C01 1K 0x50 (shadows at 0x51 - 0x57) - 24C01A 1K 0x50 - 0x57 (Typical device on DIMMs) - 24C02 2K 0x50 - 0x57 - 24C04 4K 0x50, 0x52, 0x54, 0x56 - (additional data at 0x51, 0x53, 0x55, 0x57) - 24C08 8K 0x50, 0x54 (additional data at 0x51, 0x52, - 0x53, 0x55, 0x56, 0x57) - 24C16 16K 0x50 (additional data at 0x51 - 0x57) - Sony 2K 0x57 - - Atmel 34C02B 2K 0x50 - 0x57, SW write protect at 0x30-37 - Catalyst 34FC02 2K 0x50 - 0x57, SW write protect at 0x30-37 - Catalyst 34RC02 2K 0x50 - 0x57, SW write protect at 0x30-37 - Fairchild 34W02 2K 0x50 - 0x57, SW write protect at 0x30-37 - Microchip 24AA52 2K 0x50 - 0x57, SW write protect at 0x30-37 - ST M34C02 2K 0x50 - 0x57, SW write protect at 0x30-37 - - -Authors: - Frodo Looijaard , - Philip Edelbrock , - Jean Delvare , - Greg Kroah-Hartman , - IBM Corp. - -Description ------------ - -This is a simple EEPROM module meant to enable reading the first 256 bytes -of an EEPROM (on a SDRAM DIMM for example). However, it will access serial -EEPROMs on any I2C adapter. The supported devices are generically called -24Cxx, and are listed above; however the numbering for these -industry-standard devices may vary by manufacturer. - -This module was a programming exercise to get used to the new project -organization laid out by Frodo, but it should be at least completely -effective for decoding the contents of EEPROMs on DIMMs. - -DIMMS will typically contain a 24C01A or 24C02, or the 34C02 variants. -The other devices will not be found on a DIMM because they respond to more -than one address. - -DDC Monitors may contain any device. Often a 24C01, which responds to all 8 -addresses, is found. - -Recent Sony Vaio laptops have an EEPROM at 0x57. We couldn't get the -specification, so it is guess work and far from being complete. - -The Microchip 24AA52/24LCS52, ST M34C02, and others support an additional -software write protect register at 0x30 - 0x37 (0x20 less than the memory -location). The chip responds to "write quick" detection at this address but -does not respond to byte reads. If this register is present, the lower 128 -bytes of the memory array are not write protected. Any byte data write to -this address will write protect the memory array permanently, and the -device will no longer respond at the 0x30-37 address. The eeprom driver -does not support this register. - -Lacking functionality: - -* Full support for larger devices (24C04, 24C08, 24C16). These are not -typically found on a PC. These devices will appear as separate devices at -multiple addresses. - -* Support for really large devices (24C32, 24C64, 24C128, 24C256, 24C512). -These devices require two-byte address fields and are not supported. - -* Enable Writing. Again, no technical reason why not, but making it easy -to change the contents of the EEPROMs (on DIMMs anyway) also makes it easy -to disable the DIMMs (potentially preventing the computer from booting) -until the values are restored somehow. - -Use: - -After inserting the module (and any other required SMBus/i2c modules), you -should have some EEPROM directories in /sys/bus/i2c/devices/* of names such -as "0-0050". Inside each of these is a series of files, the eeprom file -contains the binary data from EEPROM. diff --git a/Documentation/i2c/chips/max6875 b/Documentation/i2c/chips/max6875 deleted file mode 100644 index 10ca43cd1a7..00000000000 --- a/Documentation/i2c/chips/max6875 +++ /dev/null @@ -1,108 +0,0 @@ -Kernel driver max6875 -===================== - -Supported chips: - * Maxim MAX6874, MAX6875 - Prefix: 'max6875' - Addresses scanned: None (see below) - Datasheet: - http://pdfserv.maxim-ic.com/en/ds/MAX6874-MAX6875.pdf - -Author: Ben Gardner - - -Description ------------ - -The Maxim MAX6875 is an EEPROM-programmable power-supply sequencer/supervisor. -It provides timed outputs that can be used as a watchdog, if properly wired. -It also provides 512 bytes of user EEPROM. - -At reset, the MAX6875 reads the configuration EEPROM into its configuration -registers. The chip then begins to operate according to the values in the -registers. - -The Maxim MAX6874 is a similar, mostly compatible device, with more intputs -and outputs: - vin gpi vout -MAX6874 6 4 8 -MAX6875 4 3 5 - -See the datasheet for more information. - - -Sysfs entries -------------- - -eeprom - 512 bytes of user-defined EEPROM space. - - -General Remarks ---------------- - -Valid addresses for the MAX6875 are 0x50 and 0x52. -Valid addresses for the MAX6874 are 0x50, 0x52, 0x54 and 0x56. -The driver does not probe any address, so you must force the address. - -Example: -$ modprobe max6875 force=0,0x50 - -The MAX6874/MAX6875 ignores address bit 0, so this driver attaches to multiple -addresses. For example, for address 0x50, it also reserves 0x51. -The even-address instance is called 'max6875', the odd one is 'dummy'. - - -Programming the chip using i2c-dev ----------------------------------- - -Use the i2c-dev interface to access and program the chips. -Reads and writes are performed differently depending on the address range. - -The configuration registers are at addresses 0x00 - 0x45. -Use i2c_smbus_write_byte_data() to write a register and -i2c_smbus_read_byte_data() to read a register. -The command is the register number. - -Examples: -To write a 1 to register 0x45: - i2c_smbus_write_byte_data(fd, 0x45, 1); - -To read register 0x45: - value = i2c_smbus_read_byte_data(fd, 0x45); - - -The configuration EEPROM is at addresses 0x8000 - 0x8045. -The user EEPROM is at addresses 0x8100 - 0x82ff. - -Use i2c_smbus_write_word_data() to write a byte to EEPROM. - -The command is the upper byte of the address: 0x80, 0x81, or 0x82. -The data word is the lower part of the address or'd with data << 8. - cmd = address >> 8; - val = (address & 0xff) | (data << 8); - -Example: -To write 0x5a to address 0x8003: - i2c_smbus_write_word_data(fd, 0x80, 0x5a03); - - -Reading data from the EEPROM is a little more complicated. -Use i2c_smbus_write_byte_data() to set the read address and then -i2c_smbus_read_byte() or i2c_smbus_read_i2c_block_data() to read the data. - -Example: -To read data starting at offset 0x8100, first set the address: - i2c_smbus_write_byte_data(fd, 0x81, 0x00); - -And then read the data - value = i2c_smbus_read_byte(fd); - - or - - count = i2c_smbus_read_i2c_block_data(fd, 0x84, 16, buffer); - -The block read should read 16 bytes. -0x84 is the block read command. - -See the datasheet for more details. - diff --git a/Documentation/misc-devices/eeprom b/Documentation/misc-devices/eeprom new file mode 100644 index 00000000000..f7e8104b576 --- /dev/null +++ b/Documentation/misc-devices/eeprom @@ -0,0 +1,96 @@ +Kernel driver eeprom +==================== + +Supported chips: + * Any EEPROM chip in the designated address range + Prefix: 'eeprom' + Addresses scanned: I2C 0x50 - 0x57 + Datasheets: Publicly available from: + Atmel (www.atmel.com), + Catalyst (www.catsemi.com), + Fairchild (www.fairchildsemi.com), + Microchip (www.microchip.com), + Philips (www.semiconductor.philips.com), + Rohm (www.rohm.com), + ST (www.st.com), + Xicor (www.xicor.com), + and others. + + Chip Size (bits) Address + 24C01 1K 0x50 (shadows at 0x51 - 0x57) + 24C01A 1K 0x50 - 0x57 (Typical device on DIMMs) + 24C02 2K 0x50 - 0x57 + 24C04 4K 0x50, 0x52, 0x54, 0x56 + (additional data at 0x51, 0x53, 0x55, 0x57) + 24C08 8K 0x50, 0x54 (additional data at 0x51, 0x52, + 0x53, 0x55, 0x56, 0x57) + 24C16 16K 0x50 (additional data at 0x51 - 0x57) + Sony 2K 0x57 + + Atmel 34C02B 2K 0x50 - 0x57, SW write protect at 0x30-37 + Catalyst 34FC02 2K 0x50 - 0x57, SW write protect at 0x30-37 + Catalyst 34RC02 2K 0x50 - 0x57, SW write protect at 0x30-37 + Fairchild 34W02 2K 0x50 - 0x57, SW write protect at 0x30-37 + Microchip 24AA52 2K 0x50 - 0x57, SW write protect at 0x30-37 + ST M34C02 2K 0x50 - 0x57, SW write protect at 0x30-37 + + +Authors: + Frodo Looijaard , + Philip Edelbrock , + Jean Delvare , + Greg Kroah-Hartman , + IBM Corp. + +Description +----------- + +This is a simple EEPROM module meant to enable reading the first 256 bytes +of an EEPROM (on a SDRAM DIMM for example). However, it will access serial +EEPROMs on any I2C adapter. The supported devices are generically called +24Cxx, and are listed above; however the numbering for these +industry-standard devices may vary by manufacturer. + +This module was a programming exercise to get used to the new project +organization laid out by Frodo, but it should be at least completely +effective for decoding the contents of EEPROMs on DIMMs. + +DIMMS will typically contain a 24C01A or 24C02, or the 34C02 variants. +The other devices will not be found on a DIMM because they respond to more +than one address. + +DDC Monitors may contain any device. Often a 24C01, which responds to all 8 +addresses, is found. + +Recent Sony Vaio laptops have an EEPROM at 0x57. We couldn't get the +specification, so it is guess work and far from being complete. + +The Microchip 24AA52/24LCS52, ST M34C02, and others support an additional +software write protect register at 0x30 - 0x37 (0x20 less than the memory +location). The chip responds to "write quick" detection at this address but +does not respond to byte reads. If this register is present, the lower 128 +bytes of the memory array are not write protected. Any byte data write to +this address will write protect the memory array permanently, and the +device will no longer respond at the 0x30-37 address. The eeprom driver +does not support this register. + +Lacking functionality: + +* Full support for larger devices (24C04, 24C08, 24C16). These are not +typically found on a PC. These devices will appear as separate devices at +multiple addresses. + +* Support for really large devices (24C32, 24C64, 24C128, 24C256, 24C512). +These devices require two-byte address fields and are not supported. + +* Enable Writing. Again, no technical reason why not, but making it easy +to change the contents of the EEPROMs (on DIMMs anyway) also makes it easy +to disable the DIMMs (potentially preventing the computer from booting) +until the values are restored somehow. + +Use: + +After inserting the module (and any other required SMBus/i2c modules), you +should have some EEPROM directories in /sys/bus/i2c/devices/* of names such +as "0-0050". Inside each of these is a series of files, the eeprom file +contains the binary data from EEPROM. diff --git a/Documentation/misc-devices/max6875 b/Documentation/misc-devices/max6875 new file mode 100644 index 00000000000..10ca43cd1a7 --- /dev/null +++ b/Documentation/misc-devices/max6875 @@ -0,0 +1,108 @@ +Kernel driver max6875 +===================== + +Supported chips: + * Maxim MAX6874, MAX6875 + Prefix: 'max6875' + Addresses scanned: None (see below) + Datasheet: + http://pdfserv.maxim-ic.com/en/ds/MAX6874-MAX6875.pdf + +Author: Ben Gardner + + +Description +----------- + +The Maxim MAX6875 is an EEPROM-programmable power-supply sequencer/supervisor. +It provides timed outputs that can be used as a watchdog, if properly wired. +It also provides 512 bytes of user EEPROM. + +At reset, the MAX6875 reads the configuration EEPROM into its configuration +registers. The chip then begins to operate according to the values in the +registers. + +The Maxim MAX6874 is a similar, mostly compatible device, with more intputs +and outputs: + vin gpi vout +MAX6874 6 4 8 +MAX6875 4 3 5 + +See the datasheet for more information. + + +Sysfs entries +------------- + +eeprom - 512 bytes of user-defined EEPROM space. + + +General Remarks +--------------- + +Valid addresses for the MAX6875 are 0x50 and 0x52. +Valid addresses for the MAX6874 are 0x50, 0x52, 0x54 and 0x56. +The driver does not probe any address, so you must force the address. + +Example: +$ modprobe max6875 force=0,0x50 + +The MAX6874/MAX6875 ignores address bit 0, so this driver attaches to multiple +addresses. For example, for address 0x50, it also reserves 0x51. +The even-address instance is called 'max6875', the odd one is 'dummy'. + + +Programming the chip using i2c-dev +---------------------------------- + +Use the i2c-dev interface to access and program the chips. +Reads and writes are performed differently depending on the address range. + +The configuration registers are at addresses 0x00 - 0x45. +Use i2c_smbus_write_byte_data() to write a register and +i2c_smbus_read_byte_data() to read a register. +The command is the register number. + +Examples: +To write a 1 to register 0x45: + i2c_smbus_write_byte_data(fd, 0x45, 1); + +To read register 0x45: + value = i2c_smbus_read_byte_data(fd, 0x45); + + +The configuration EEPROM is at addresses 0x8000 - 0x8045. +The user EEPROM is at addresses 0x8100 - 0x82ff. + +Use i2c_smbus_write_word_data() to write a byte to EEPROM. + +The command is the upper byte of the address: 0x80, 0x81, or 0x82. +The data word is the lower part of the address or'd with data << 8. + cmd = address >> 8; + val = (address & 0xff) | (data << 8); + +Example: +To write 0x5a to address 0x8003: + i2c_smbus_write_word_data(fd, 0x80, 0x5a03); + + +Reading data from the EEPROM is a little more complicated. +Use i2c_smbus_write_byte_data() to set the read address and then +i2c_smbus_read_byte() or i2c_smbus_read_i2c_block_data() to read the data. + +Example: +To read data starting at offset 0x8100, first set the address: + i2c_smbus_write_byte_data(fd, 0x81, 0x00); + +And then read the data + value = i2c_smbus_read_byte(fd); + + or + + count = i2c_smbus_read_i2c_block_data(fd, 0x84, 16, buffer); + +The block read should read 16 bytes. +0x84 is the block read command. + +See the datasheet for more details. + -- cgit v1.2.3 From b835d7fbd54c42d7b9abb5e8a64f32690ebfad43 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 4 Oct 2009 22:53:41 +0200 Subject: max6875: Discard obsolete detect method There is no point in implementing a detect callback for the MAX6875, as this device can't be detected. It was there solely to handle "force" module parameters to instantiate devices, but now we have a better sysfs interface that can do the same. So we can get rid of the ugly module parameters and the detect callback. This basically divides the binary module size by 2. Signed-off-by: Jean Delvare Acked-by: Wolfram Sang Acked-by: Ben Gardner --- Documentation/misc-devices/max6875 | 6 ++++-- drivers/misc/eeprom/max6875.c | 29 +++++------------------------ 2 files changed, 9 insertions(+), 26 deletions(-) diff --git a/Documentation/misc-devices/max6875 b/Documentation/misc-devices/max6875 index 10ca43cd1a7..1e89ee3ccc1 100644 --- a/Documentation/misc-devices/max6875 +++ b/Documentation/misc-devices/max6875 @@ -42,10 +42,12 @@ General Remarks Valid addresses for the MAX6875 are 0x50 and 0x52. Valid addresses for the MAX6874 are 0x50, 0x52, 0x54 and 0x56. -The driver does not probe any address, so you must force the address. +The driver does not probe any address, so you explicitly instantiate the +devices. Example: -$ modprobe max6875 force=0,0x50 +$ modprobe max6875 +$ echo max6875 0x50 > /sys/bus/i2c/devices/i2c-0/new_device The MAX6874/MAX6875 ignores address bit 0, so this driver attaches to multiple addresses. For example, for address 0x50, it also reserves 0x51. diff --git a/drivers/misc/eeprom/max6875.c b/drivers/misc/eeprom/max6875.c index 3c0c58eed34..5a6b2bce8ad 100644 --- a/drivers/misc/eeprom/max6875.c +++ b/drivers/misc/eeprom/max6875.c @@ -33,12 +33,6 @@ #include #include -/* Do not scan - the MAX6875 access method will write to some EEPROM chips */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_1(max6875); - /* The MAX6875 can only read/write 16 bytes at a time */ #define SLICE_SIZE 16 #define SLICE_BITS 4 @@ -146,31 +140,21 @@ static struct bin_attribute user_eeprom_attr = { .read = max6875_read, }; -/* Return 0 if detection is successful, -ENODEV otherwise */ -static int max6875_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) +static int max6875_probe(struct i2c_client *client, + const struct i2c_device_id *id) { struct i2c_adapter *adapter = client->adapter; + struct max6875_data *data; + int err; if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA | I2C_FUNC_SMBUS_READ_BYTE)) return -ENODEV; - /* Only check even addresses */ + /* Only bind to even addresses */ if (client->addr & 1) return -ENODEV; - strlcpy(info->type, "max6875", I2C_NAME_SIZE); - - return 0; -} - -static int max6875_probe(struct i2c_client *client, - const struct i2c_device_id *id) -{ - struct max6875_data *data; - int err; - if (!(data = kzalloc(sizeof(struct max6875_data), GFP_KERNEL))) return -ENOMEM; @@ -222,9 +206,6 @@ static struct i2c_driver max6875_driver = { .probe = max6875_probe, .remove = max6875_remove, .id_table = max6875_id, - - .detect = max6875_detect, - .address_data = &addr_data, }; static int __init max6875_init(void) -- cgit v1.2.3 From 0314b020c49c1d6cd182d2b89775bfa6686660db Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 4 Oct 2009 22:53:41 +0200 Subject: ds2482: Discard obsolete detect method There is no point in implementing a detect callback for the DS2482, as this device can't be detected. It was there solely to handle "force" module parameters to instantiate devices, but now we have a better sysfs interface that can do the same. So we can get rid of the ugly module parameters and the detect callback. This shrinks the binary module size by 21%. Signed-off-by: Jean Delvare Acked-by: Ben Gardner --- Documentation/w1/masters/ds2482 | 6 +++--- drivers/w1/masters/ds2482.c | 35 +++++------------------------------ 2 files changed, 8 insertions(+), 33 deletions(-) diff --git a/Documentation/w1/masters/ds2482 b/Documentation/w1/masters/ds2482 index 9210d6fa502..299b91c7609 100644 --- a/Documentation/w1/masters/ds2482 +++ b/Documentation/w1/masters/ds2482 @@ -24,8 +24,8 @@ General Remarks Valid addresses are 0x18, 0x19, 0x1a, and 0x1b. However, the device cannot be detected without writing to the i2c bus, so no -detection is done. -You should force the device address. +detection is done. You should instantiate the device explicitly. -$ modprobe ds2482 force=0,0x18 +$ modprobe ds2482 +$ echo ds2482 0x18 > /sys/bus/i2c/devices/i2c-0/new_device diff --git a/drivers/w1/masters/ds2482.c b/drivers/w1/masters/ds2482.c index df52cb355f7..406caa6a71c 100644 --- a/drivers/w1/masters/ds2482.c +++ b/drivers/w1/masters/ds2482.c @@ -23,19 +23,6 @@ #include "../w1.h" #include "../w1_int.h" -/** - * Address is selected using 2 pins, resulting in 4 possible addresses. - * 0x18, 0x19, 0x1a, 0x1b - * However, the chip cannot be detected without doing an i2c write, - * so use the force module parameter. - */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/** - * Insmod parameters - */ -I2C_CLIENT_INSMOD_1(ds2482); - /** * The DS2482 registers - there are 3 registers that are addressed by a read * pointer. The read pointer is set by the last command executed. @@ -96,8 +83,6 @@ static const u8 ds2482_chan_rd[8] = static int ds2482_probe(struct i2c_client *client, const struct i2c_device_id *id); -static int ds2482_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info); static int ds2482_remove(struct i2c_client *client); @@ -117,8 +102,6 @@ static struct i2c_driver ds2482_driver = { .probe = ds2482_probe, .remove = ds2482_remove, .id_table = ds2482_id, - .detect = ds2482_detect, - .address_data = &addr_data, }; /* @@ -425,19 +408,6 @@ static u8 ds2482_w1_reset_bus(void *data) } -static int ds2482_detect(struct i2c_client *client, int kind, - struct i2c_board_info *info) -{ - if (!i2c_check_functionality(client->adapter, - I2C_FUNC_SMBUS_WRITE_BYTE_DATA | - I2C_FUNC_SMBUS_BYTE)) - return -ENODEV; - - strlcpy(info->type, "ds2482", I2C_NAME_SIZE); - - return 0; -} - static int ds2482_probe(struct i2c_client *client, const struct i2c_device_id *id) { @@ -446,6 +416,11 @@ static int ds2482_probe(struct i2c_client *client, int temp1; int idx; + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_WRITE_BYTE_DATA | + I2C_FUNC_SMBUS_BYTE)) + return -ENODEV; + if (!(data = kzalloc(sizeof(struct ds2482_data), GFP_KERNEL))) { err = -ENOMEM; goto exit; -- cgit v1.2.3 From 2d2a7cff1b63cde1e2d981eea8ae9e69ae9ce96d Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 4 Oct 2009 22:53:42 +0200 Subject: ltc4215/ltc4245: Discard obsolete detect methods There is no point in implementing a detect callback for the LTC4215 and LTC4245, as these devices can't be detected. It was there solely to handle "force" module parameters to instantiate devices, but now we have a better sysfs interface that can do the same. So we can get rid of the ugly module parameters and the detect callbacks. This shrinks the binary module sizes by 36% and 46%, respectively. Signed-off-by: Jean Delvare Cc: Ira W. Snyder --- Documentation/hwmon/ltc4215 | 7 ++- Documentation/hwmon/ltc4245 | 7 ++- drivers/hwmon/ltc4215.c | 47 ++-------------- drivers/hwmon/ltc4245.c | 131 ++------------------------------------------ 4 files changed, 18 insertions(+), 174 deletions(-) diff --git a/Documentation/hwmon/ltc4215 b/Documentation/hwmon/ltc4215 index 2e6a21eb656..c196a184625 100644 --- a/Documentation/hwmon/ltc4215 +++ b/Documentation/hwmon/ltc4215 @@ -22,12 +22,13 @@ Usage Notes ----------- This driver does not probe for LTC4215 devices, due to the fact that some -of the possible addresses are unfriendly to probing. You will need to use -the "force" parameter to tell the driver where to find the device. +of the possible addresses are unfriendly to probing. You will have to +instantiate the devices explicitly. Example: the following will load the driver for an LTC4215 at address 0x44 on I2C bus #0: -$ modprobe ltc4215 force=0,0x44 +$ modprobe ltc4215 +$ echo ltc4215 0x44 > /sys/bus/i2c/devices/i2c-0/new_device Sysfs entries diff --git a/Documentation/hwmon/ltc4245 b/Documentation/hwmon/ltc4245 index bae7a3adc5d..02838a47d86 100644 --- a/Documentation/hwmon/ltc4245 +++ b/Documentation/hwmon/ltc4245 @@ -23,12 +23,13 @@ Usage Notes ----------- This driver does not probe for LTC4245 devices, due to the fact that some -of the possible addresses are unfriendly to probing. You will need to use -the "force" parameter to tell the driver where to find the device. +of the possible addresses are unfriendly to probing. You will have to +instantiate the devices explicitly. Example: the following will load the driver for an LTC4245 at address 0x23 on I2C bus #1: -$ modprobe ltc4245 force=1,0x23 +$ modprobe ltc4245 +$ echo ltc4245 0x23 > /sys/bus/i2c/devices/i2c-1/new_device Sysfs entries diff --git a/drivers/hwmon/ltc4215.c b/drivers/hwmon/ltc4215.c index 6c9a04136e0..00d975eb5b8 100644 --- a/drivers/hwmon/ltc4215.c +++ b/drivers/hwmon/ltc4215.c @@ -20,11 +20,6 @@ #include #include -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_1(ltc4215); - /* Here are names of the chip's registers (a.k.a. commands) */ enum ltc4215_cmd { LTC4215_CONTROL = 0x00, /* rw */ @@ -246,9 +241,13 @@ static const struct attribute_group ltc4215_group = { static int ltc4215_probe(struct i2c_client *client, const struct i2c_device_id *id) { + struct i2c_adapter *adapter = client->adapter; struct ltc4215_data *data; int ret; + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -ENODEV; + data = kzalloc(sizeof(*data), GFP_KERNEL); if (!data) { ret = -ENOMEM; @@ -294,56 +293,20 @@ static int ltc4215_remove(struct i2c_client *client) return 0; } -static int ltc4215_detect(struct i2c_client *client, - int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - return -ENODEV; - - if (kind < 0) { /* probed detection - check the chip type */ - s32 v; /* 8 bits from the chip, or -ERRNO */ - - /* - * Register 0x01 bit b7 is reserved, expect 0 - * Register 0x03 bit b6 and b7 are reserved, expect 0 - */ - v = i2c_smbus_read_byte_data(client, LTC4215_ALERT); - if (v < 0 || (v & (1 << 7)) != 0) - return -ENODEV; - - v = i2c_smbus_read_byte_data(client, LTC4215_FAULT); - if (v < 0 || (v & ((1 << 6) | (1 << 7))) != 0) - return -ENODEV; - } - - strlcpy(info->type, "ltc4215", I2C_NAME_SIZE); - dev_info(&adapter->dev, "ltc4215 %s at address 0x%02x\n", - kind < 0 ? "probed" : "forced", - client->addr); - - return 0; -} - static const struct i2c_device_id ltc4215_id[] = { - { "ltc4215", ltc4215 }, + { "ltc4215", 0 }, { } }; MODULE_DEVICE_TABLE(i2c, ltc4215_id); /* This is the driver that will be inserted */ static struct i2c_driver ltc4215_driver = { - .class = I2C_CLASS_HWMON, .driver = { .name = "ltc4215", }, .probe = ltc4215_probe, .remove = ltc4215_remove, .id_table = ltc4215_id, - .detect = ltc4215_detect, - .address_data = &addr_data, }; static int __init ltc4215_init(void) diff --git a/drivers/hwmon/ltc4245.c b/drivers/hwmon/ltc4245.c index e3896433361..65c232a9d0c 100644 --- a/drivers/hwmon/ltc4245.c +++ b/drivers/hwmon/ltc4245.c @@ -22,15 +22,6 @@ #include #include -/* Valid addresses are 0x20 - 0x3f - * - * For now, we do not probe, since some of these addresses - * are known to be unfriendly to probing */ -static const unsigned short normal_i2c[] = { I2C_CLIENT_END }; - -/* Insmod parameters */ -I2C_CLIENT_INSMOD_1(ltc4245); - /* Here are names of the chip's registers (a.k.a. commands) */ enum ltc4245_cmd { LTC4245_STATUS = 0x00, /* readonly */ @@ -369,9 +360,13 @@ static const struct attribute_group ltc4245_group = { static int ltc4245_probe(struct i2c_client *client, const struct i2c_device_id *id) { + struct i2c_adapter *adapter = client->adapter; struct ltc4245_data *data; int ret; + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -ENODEV; + data = kzalloc(sizeof(*data), GFP_KERNEL); if (!data) { ret = -ENOMEM; @@ -418,136 +413,20 @@ static int ltc4245_remove(struct i2c_client *client) return 0; } -/* Check that some bits in a control register appear at all possible - * locations without changing value - * - * @client: the i2c client to use - * @reg: the register to read - * @bits: the bits to check (0xff checks all bits, - * 0x03 checks only the last two bits) - * - * return -ERRNO if the register read failed - * return -ENODEV if the register value doesn't stay constant at all - * possible addresses - * - * return 0 for success - */ -static int ltc4245_check_control_reg(struct i2c_client *client, u8 reg, u8 bits) -{ - int i; - s32 v, voff1, voff2; - - /* Read register and check for error */ - v = i2c_smbus_read_byte_data(client, reg); - if (v < 0) - return v; - - v &= bits; - - for (i = 0x00; i < 0xff; i += 0x20) { - - voff1 = i2c_smbus_read_byte_data(client, reg + i); - if (voff1 < 0) - return voff1; - - voff2 = i2c_smbus_read_byte_data(client, reg + i + 0x08); - if (voff2 < 0) - return voff2; - - voff1 &= bits; - voff2 &= bits; - - if (v != voff1 || v != voff2) - return -ENODEV; - } - - return 0; -} - -static int ltc4245_detect(struct i2c_client *client, - int kind, - struct i2c_board_info *info) -{ - struct i2c_adapter *adapter = client->adapter; - - if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) - return -ENODEV; - - if (kind < 0) { /* probed detection - check the chip type */ - s32 v; /* 8 bits from the chip, or -ERRNO */ - - /* Chip registers 0x00-0x07 are control registers - * Chip registers 0x10-0x1f are data registers - * - * Address bits b7-b5 are ignored. This makes the chip "repeat" - * in steps of 0x20. Any control registers should appear with - * the same values across all duplicated addresses. - * - * Register 0x02 bit b2 is reserved, expect 0 - * Register 0x07 bits b7 to b4 are reserved, expect 0 - * - * Registers 0x01, 0x02 are control registers and should not - * change on their own. - * - * Register 0x06 bits b6 and b7 are control bits, and should - * not change on their own. - * - * Register 0x07 bits b3 to b0 are control bits, and should - * not change on their own. - */ - - /* read register 0x02 reserved bit, expect 0 */ - v = i2c_smbus_read_byte_data(client, LTC4245_CONTROL); - if (v < 0 || (v & 0x04) != 0) - return -ENODEV; - - /* read register 0x07 reserved bits, expect 0 */ - v = i2c_smbus_read_byte_data(client, LTC4245_ADCADR); - if (v < 0 || (v & 0xf0) != 0) - return -ENODEV; - - /* check that the alert register appears at all locations */ - if (ltc4245_check_control_reg(client, LTC4245_ALERT, 0xff)) - return -ENODEV; - - /* check that the control register appears at all locations */ - if (ltc4245_check_control_reg(client, LTC4245_CONTROL, 0xff)) - return -ENODEV; - - /* check that register 0x06 bits b6 and b7 stay constant */ - if (ltc4245_check_control_reg(client, LTC4245_GPIO, 0xc0)) - return -ENODEV; - - /* check that register 0x07 bits b3-b0 stay constant */ - if (ltc4245_check_control_reg(client, LTC4245_ADCADR, 0x0f)) - return -ENODEV; - } - - strlcpy(info->type, "ltc4245", I2C_NAME_SIZE); - dev_info(&adapter->dev, "ltc4245 %s at address 0x%02x\n", - kind < 0 ? "probed" : "forced", - client->addr); - - return 0; -} - static const struct i2c_device_id ltc4245_id[] = { - { "ltc4245", ltc4245 }, + { "ltc4245", 0 }, { } }; MODULE_DEVICE_TABLE(i2c, ltc4245_id); /* This is the driver that will be inserted */ static struct i2c_driver ltc4245_driver = { - .class = I2C_CLASS_HWMON, .driver = { .name = "ltc4245", }, .probe = ltc4245_probe, .remove = ltc4245_remove, .id_table = ltc4245_id, - .detect = ltc4245_detect, - .address_data = &addr_data, }; static int __init ltc4245_init(void) -- cgit v1.2.3 From 77279862bad879c1c194171f5cf6b5b0e7abe384 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 4 Oct 2009 22:53:43 +0200 Subject: leds: leds-pca9532 - Drop unused module parameters The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which implement device detection. The leds-pca9532 driver doesn't, so there is no point in calling it. Signed-off-by: Jean Delvare Cc: Richard Purdie Cc: Riku Voipio --- drivers/leds/leds-pca9532.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/drivers/leds/leds-pca9532.c b/drivers/leds/leds-pca9532.c index 708a8017c21..adc561eb59d 100644 --- a/drivers/leds/leds-pca9532.c +++ b/drivers/leds/leds-pca9532.c @@ -19,9 +19,6 @@ #include #include -static const unsigned short normal_i2c[] = { /*0x60,*/ I2C_CLIENT_END}; -I2C_CLIENT_INSMOD_1(pca9532); - #define PCA9532_REG_PSC(i) (0x2+(i)*2) #define PCA9532_REG_PWM(i) (0x3+(i)*2) #define PCA9532_REG_LS0 0x6 -- cgit v1.2.3 From 0d83f18b17f89dd745e27759d0464fb29ef6eb65 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 4 Oct 2009 22:53:43 +0200 Subject: Staging: IIO: tsl2561: Drop unused module parameters The I2C_CLIENT_INSMOD macro is only useful for i2c drivers which implement device detection. The tsl2561 driver doesn't, so there is no point in calling it. Signed-off-by: Jean Delvare Cc: Jonathan Cameron --- drivers/staging/iio/light/tsl2561.c | 4 ---- 1 file changed, 4 deletions(-) diff --git a/drivers/staging/iio/light/tsl2561.c b/drivers/staging/iio/light/tsl2561.c index ea8a5efc19b..fc2107f4c04 100644 --- a/drivers/staging/iio/light/tsl2561.c +++ b/drivers/staging/iio/light/tsl2561.c @@ -239,10 +239,6 @@ static int __devexit tsl2561_remove(struct i2c_client *client) return tsl2561_powerdown(client); } -static unsigned short normal_i2c[] = { 0x29, 0x39, 0x49, I2C_CLIENT_END }; - -I2C_CLIENT_INSMOD; - static const struct i2c_device_id tsl2561_id[] = { { "tsl2561", 0 }, { } -- cgit v1.2.3 From dcffa12551cc1779970e9c8ba01e87aff92d25d1 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 4 Oct 2009 22:53:44 +0200 Subject: mfd: AB3100 drop unused module parameters The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which implement device detection. The ab3100 driver doesn't, so there is no point in calling it. Signed-off-by: Jean Delvare Acked-by: Linus Walleij Cc: Samuel Ortiz --- drivers/mfd/ab3100-core.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/mfd/ab3100-core.c b/drivers/mfd/ab3100-core.c index 5447da16a17..61348102827 100644 --- a/drivers/mfd/ab3100-core.c +++ b/drivers/mfd/ab3100-core.c @@ -57,8 +57,6 @@ * The AB3100 is usually assigned address 0x48 (7-bit) * The chip is defined in the platform i2c_board_data section. */ -static unsigned short normal_i2c[] = { 0x48, I2C_CLIENT_END }; -I2C_CLIENT_INSMOD_1(ab3100); u8 ab3100_get_chip_type(struct ab3100 *ab3100) { @@ -966,7 +964,7 @@ static int __exit ab3100_remove(struct i2c_client *client) } static const struct i2c_device_id ab3100_id[] = { - { "ab3100", ab3100 }, + { "ab3100", 0 }, { } }; MODULE_DEVICE_TABLE(i2c, ab3100_id); -- cgit v1.2.3 From 03f1805ad0ce5aae02bfe40c29b230abb63179ac Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 4 Oct 2009 22:53:45 +0200 Subject: i2c: Minor documentation update The sysfs path to i2c adapters has changed recently, update the documentation to reflect that change. Signed-off-by: Jean Delvare --- Documentation/i2c/instantiating-devices | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Documentation/i2c/instantiating-devices b/Documentation/i2c/instantiating-devices index c740b7b4108..e89490270ab 100644 --- a/Documentation/i2c/instantiating-devices +++ b/Documentation/i2c/instantiating-devices @@ -188,7 +188,7 @@ segment, the address is sufficient to uniquely identify the device to be deleted. Example: -# echo eeprom 0x50 > /sys/class/i2c-adapter/i2c-3/new_device +# echo eeprom 0x50 > /sys/bus/i2c/devices/i2c-3/new_device While this interface should only be used when in-kernel device declaration can't be done, there is a variety of cases where it can be helpful: -- cgit v1.2.3 From 18669eabde2ff5fc446e72e043f0539059763438 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 4 Oct 2009 22:53:45 +0200 Subject: i2c: Hide probe errors caused by ACPI resource conflicts When an ACPI resource conflict is detected, error messages are already printed by ACPI. There's no point in causing the driver core to print more error messages, so return one of the error codes for which no message is printed. This fixes bug #14293: http://bugzilla.kernel.org/show_bug.cgi?id=14293 Signed-off-by: Jean Delvare --- drivers/i2c/busses/i2c-amd756.c | 2 +- drivers/i2c/busses/i2c-amd8111.c | 4 +++- drivers/i2c/busses/i2c-i801.c | 4 +++- drivers/i2c/busses/i2c-isch.c | 2 +- drivers/i2c/busses/i2c-piix4.c | 4 ++-- drivers/i2c/busses/i2c-sis96x.c | 2 +- drivers/i2c/busses/i2c-viapro.c | 2 +- 7 files changed, 12 insertions(+), 8 deletions(-) diff --git a/drivers/i2c/busses/i2c-amd756.c b/drivers/i2c/busses/i2c-amd756.c index f7d6fe9c49b..8f0b90ef8c7 100644 --- a/drivers/i2c/busses/i2c-amd756.c +++ b/drivers/i2c/busses/i2c-amd756.c @@ -364,7 +364,7 @@ static int __devinit amd756_probe(struct pci_dev *pdev, error = acpi_check_region(amd756_ioport, SMB_IOSIZE, amd756_driver.name); if (error) - return error; + return -ENODEV; if (!request_region(amd756_ioport, SMB_IOSIZE, amd756_driver.name)) { dev_err(&pdev->dev, "SMB region 0x%x already in use!\n", diff --git a/drivers/i2c/busses/i2c-amd8111.c b/drivers/i2c/busses/i2c-amd8111.c index a7c59908c45..5b4ad86ca16 100644 --- a/drivers/i2c/busses/i2c-amd8111.c +++ b/drivers/i2c/busses/i2c-amd8111.c @@ -376,8 +376,10 @@ static int __devinit amd8111_probe(struct pci_dev *dev, smbus->size = pci_resource_len(dev, 0); error = acpi_check_resource_conflict(&dev->resource[0]); - if (error) + if (error) { + error = -ENODEV; goto out_kfree; + } if (!request_region(smbus->base, smbus->size, amd8111_driver.name)) { error = -EBUSY; diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c index 9d2c5adf5d4..55edcfe5b85 100644 --- a/drivers/i2c/busses/i2c-i801.c +++ b/drivers/i2c/busses/i2c-i801.c @@ -732,8 +732,10 @@ static int __devinit i801_probe(struct pci_dev *dev, const struct pci_device_id } err = acpi_check_resource_conflict(&dev->resource[SMBBAR]); - if (err) + if (err) { + err = -ENODEV; goto exit; + } err = pci_request_region(dev, SMBBAR, i801_driver.name); if (err) { diff --git a/drivers/i2c/busses/i2c-isch.c b/drivers/i2c/busses/i2c-isch.c index 9f6b8e0f863..dba6eb053e2 100644 --- a/drivers/i2c/busses/i2c-isch.c +++ b/drivers/i2c/busses/i2c-isch.c @@ -281,7 +281,7 @@ static int __devinit sch_probe(struct pci_dev *dev, return -ENODEV; } if (acpi_check_region(sch_smba, SMBIOSIZE, sch_driver.name)) - return -EBUSY; + return -ENODEV; if (!request_region(sch_smba, SMBIOSIZE, sch_driver.name)) { dev_err(&dev->dev, "SMBus region 0x%x already in use!\n", sch_smba); diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c index a782c7a08f9..d26a972aaca 100644 --- a/drivers/i2c/busses/i2c-piix4.c +++ b/drivers/i2c/busses/i2c-piix4.c @@ -169,7 +169,7 @@ static int __devinit piix4_setup(struct pci_dev *PIIX4_dev, } if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) - return -EBUSY; + return -ENODEV; if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) { dev_err(&PIIX4_dev->dev, "SMBus region 0x%x already in use!\n", @@ -260,7 +260,7 @@ static int __devinit piix4_setup_sb800(struct pci_dev *PIIX4_dev, piix4_smba = ((smba_en_hi << 8) | smba_en_lo) & 0xffe0; if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) - return -EBUSY; + return -ENODEV; if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) { dev_err(&PIIX4_dev->dev, "SMBus region 0x%x already in use!\n", diff --git a/drivers/i2c/busses/i2c-sis96x.c b/drivers/i2c/busses/i2c-sis96x.c index 8295885b2fd..1649963b00d 100644 --- a/drivers/i2c/busses/i2c-sis96x.c +++ b/drivers/i2c/busses/i2c-sis96x.c @@ -280,7 +280,7 @@ static int __devinit sis96x_probe(struct pci_dev *dev, retval = acpi_check_resource_conflict(&dev->resource[SIS96x_BAR]); if (retval) - return retval; + return -ENODEV; /* Everything is happy, let's grab the memory and set things up. */ if (!request_region(sis96x_smbus_base, SMB_IOSIZE, diff --git a/drivers/i2c/busses/i2c-viapro.c b/drivers/i2c/busses/i2c-viapro.c index 54d810a4d00..e4b1543015a 100644 --- a/drivers/i2c/busses/i2c-viapro.c +++ b/drivers/i2c/busses/i2c-viapro.c @@ -365,7 +365,7 @@ static int __devinit vt596_probe(struct pci_dev *pdev, found: error = acpi_check_region(vt596_smba, 8, vt596_driver.name); if (error) - return error; + return -ENODEV; if (!request_region(vt596_smba, 8, vt596_driver.name)) { dev_err(&pdev->dev, "SMBus region 0x%x already in use!\n", -- cgit v1.2.3 From 6f6b35e133fe4313277b30fc1a7ea313875ea6c9 Mon Sep 17 00:00:00 2001 From: Jean Delvare Date: Sun, 4 Oct 2009 22:53:46 +0200 Subject: macintosh: Don't assume i2c device probing always succeeds If i2c device probing fails, then there is no driver to dereference after calling i2c_new_device(). Stop assuming that probing will always succeed, to avoid NULL pointer dereferences. We have an easier access to the driver anyway. Signed-off-by: Jean Delvare Tested-by: Tim Shepard Cc: Colin Leroy --- drivers/macintosh/therm_adt746x.c | 4 +++- drivers/macintosh/therm_pm72.c | 4 +++- drivers/macintosh/windfarm_lm75_sensor.c | 4 +++- drivers/macintosh/windfarm_max6690_sensor.c | 4 +++- drivers/macintosh/windfarm_smu_sat.c | 4 +++- 5 files changed, 15 insertions(+), 5 deletions(-) diff --git a/drivers/macintosh/therm_adt746x.c b/drivers/macintosh/therm_adt746x.c index fde377c60cc..556f0feaa4d 100644 --- a/drivers/macintosh/therm_adt746x.c +++ b/drivers/macintosh/therm_adt746x.c @@ -124,6 +124,8 @@ read_reg(struct thermostat* th, int reg) return data; } +static struct i2c_driver thermostat_driver; + static int attach_thermostat(struct i2c_adapter *adapter) { @@ -148,7 +150,7 @@ attach_thermostat(struct i2c_adapter *adapter) * Let i2c-core delete that device on driver removal. * This is safe because i2c-core holds the core_lock mutex for us. */ - list_add_tail(&client->detected, &client->driver->clients); + list_add_tail(&client->detected, &thermostat_driver.clients); return 0; } diff --git a/drivers/macintosh/therm_pm72.c b/drivers/macintosh/therm_pm72.c index a028598af2d..ea32c7e5a9a 100644 --- a/drivers/macintosh/therm_pm72.c +++ b/drivers/macintosh/therm_pm72.c @@ -286,6 +286,8 @@ struct fcu_fan_table fcu_fans[] = { }, }; +static struct i2c_driver therm_pm72_driver; + /* * Utility function to create an i2c_client structure and * attach it to one of u3 adapters @@ -318,7 +320,7 @@ static struct i2c_client *attach_i2c_chip(int id, const char *name) * Let i2c-core delete that device on driver removal. * This is safe because i2c-core holds the core_lock mutex for us. */ - list_add_tail(&clt->detected, &clt->driver->clients); + list_add_tail(&clt->detected, &therm_pm72_driver.clients); return clt; } diff --git a/drivers/macintosh/windfarm_lm75_sensor.c b/drivers/macintosh/windfarm_lm75_sensor.c index 529886c7a82..ed6426a1077 100644 --- a/drivers/macintosh/windfarm_lm75_sensor.c +++ b/drivers/macintosh/windfarm_lm75_sensor.c @@ -115,6 +115,8 @@ static int wf_lm75_probe(struct i2c_client *client, return rc; } +static struct i2c_driver wf_lm75_driver; + static struct i2c_client *wf_lm75_create(struct i2c_adapter *adapter, u8 addr, int ds1775, const char *loc) @@ -157,7 +159,7 @@ static struct i2c_client *wf_lm75_create(struct i2c_adapter *adapter, * Let i2c-core delete that device on driver removal. * This is safe because i2c-core holds the core_lock mutex for us. */ - list_add_tail(&client->detected, &client->driver->clients); + list_add_tail(&client->detected, &wf_lm75_driver.clients); return client; fail: return NULL; diff --git a/drivers/macintosh/windfarm_max6690_sensor.c b/drivers/macintosh/windfarm_max6690_sensor.c index e2a55ecda2b..a67b349319e 100644 --- a/drivers/macintosh/windfarm_max6690_sensor.c +++ b/drivers/macintosh/windfarm_max6690_sensor.c @@ -88,6 +88,8 @@ static int wf_max6690_probe(struct i2c_client *client, return rc; } +static struct i2c_driver wf_max6690_driver; + static struct i2c_client *wf_max6690_create(struct i2c_adapter *adapter, u8 addr, const char *loc) { @@ -119,7 +121,7 @@ static struct i2c_client *wf_max6690_create(struct i2c_adapter *adapter, * Let i2c-core delete that device on driver removal. * This is safe because i2c-core holds the core_lock mutex for us. */ - list_add_tail(&client->detected, &client->driver->clients); + list_add_tail(&client->detected, &wf_max6690_driver.clients); return client; fail: diff --git a/drivers/macintosh/windfarm_smu_sat.c b/drivers/macintosh/windfarm_smu_sat.c index 5da729e58f9..e20330a2895 100644 --- a/drivers/macintosh/windfarm_smu_sat.c +++ b/drivers/macintosh/windfarm_smu_sat.c @@ -194,6 +194,8 @@ static struct wf_sensor_ops wf_sat_ops = { .owner = THIS_MODULE, }; +static struct i2c_driver wf_sat_driver; + static void wf_sat_create(struct i2c_adapter *adapter, struct device_node *dev) { struct i2c_board_info info; @@ -222,7 +224,7 @@ static void wf_sat_create(struct i2c_adapter *adapter, struct device_node *dev) * Let i2c-core delete that device on driver removal. * This is safe because i2c-core holds the core_lock mutex for us. */ - list_add_tail(&client->detected, &client->driver->clients); + list_add_tail(&client->detected, &wf_sat_driver.clients); } static int wf_sat_probe(struct i2c_client *client, -- cgit v1.2.3