summaryrefslogtreecommitdiff
path: root/sound/pci/oxygen
AgeCommit message (Collapse)AuthorFilesLines
2011-10-31sound: Add export.h for THIS_MODULE/EXPORT_SYMBOL where neededPaul Gortmaker1-0/+1
These aren't modules, but they do make use of these macros, so they will need export.h to get that definition. Previously, they got it via the implicit module.h inclusion. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31sound: Add module.h to the previously silent sound usersPaul Gortmaker3-0/+3
Lots of sound drivers were getting module.h via the implicit presence of it in <linux/device.h> but we are going to clean that up. So fix up those users now. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-09-14ALSA: mpu401: clean up interrupt specificationClemens Ladisch1-3/+3
The semantics of snd_mpu401_uart_new()'s interrupt parameters are somewhat counterintuitive: To prevent the function from allocating its own interrupt, either the irq number must be invalid, or the irq_flags parameter must be zero. At the same time, the irq parameter being invalid specifies that the mpu401 code has to work without an interrupt allocated by the caller. This implies that, if there is an interrupt and it is allocated by the caller, the irq parameter must be set to a valid-looking number which then isn't actually used. With the removal of IRQF_DISABLED, zero becomes a valid irq_flags value, which forces us to handle the parameters differently. This patch introduces a new flag MPU401_INFO_IRQ_HOOK for when the device interrupt is handled by the caller, and makes the allocation of the interrupt to depend only on the irq parameter. As suggested by Takashi, the irq_flags parameter was dropped because, when used, it had the constant value IRQF_DISABLED. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-08-15ALSA: virtuoso: fix Essence ST(X) S/PDIF inputClemens Ladisch1-0/+1
On the Xonar Essence ST/STX, the connector J14 has been confirmed to be a digital input, so enable it in the driver. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-07-18ALSA: virtuoso: fix silent analog output on Xonar Essence ST DeluxeClemens Ladisch1-1/+4
Commit dd203fa97bd5 (ALSA: virtuoso: remove non-working controls on Essence ST Deluxe) made it impossible to adjust the volume after the driver initialized it to muted. Ensure that those DACs that can be accessed with I2C are initialized to the same volume that is the reset default of the DAC without I2C. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: 2.6.38+ <stable@kernel.org>
2011-06-17ALSA: firewire-speakers, oxygen, ua101: allow > 10 s periodsClemens Ladisch1-6/+0
Since commit f2b3614cefb6 (Don't check DMA time-out too shortly), drivers need no longer restrict their PCM period length to be shorter than 10 seconds. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-06-10ALSA: use KBUILD_MODNAME for request_irq argument in sound/pci/*Takashi Iwai1-1/+1
The name argument of request_irq() appears in /proc/interrupts, and it's quite ugly when the name entry contains a space or special letters. In general, it's simpler and more readable when the module name appears there, so let's replace all entries with KBUILD_MODNAME. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-06-10ALSA: Use KBUILD_MODNAME for pci_driver.name entriesTakashi Iwai2-2/+2
The convention for pci_driver.name entry in kernel drivers seem to be the module name or equivalent ones. But, so far, almost all PCI sound drivers use more verbose name like "ABC Xyz (12)", and these are fairly confusing when appearing as a file name. This patch converts the all pci_driver.name entries in sound/pci/* to use KBUILD_MODNAME for more unified appearance. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-31ALSA: oxygen: fix output routing on Xonar DGClemens Ladisch3-0/+40
This card uses separate I2S outputs for the front speakers and headphones, and reverses the order of the three speaker outputs. To work around this, add a model-specific callback to adjust the controller's playback routing. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-22ALSA: Xonar, CS43xx: Don't overrun static arrayJesper Juhl1-1/+1
'cs4398_regs' in 'struct xonar_cs43xx' is an array of 'u8' with a size of 8. So, this code in sound/pci/oxygen/xonar_cs43xx.c::dump_d1_registers() for (i = 2; i <= 8; ++i) snd_iprintf(buffer, " %02x", data->cs4398_regs[i]); will overrun the array when 'i == 8'. I guess that what's needed to fix it is the trivial patch below, but I must admit that I have no idea about this code, so I may very well be wrong. Additionally, I have no way to actually test this, so all I know is that the below compiles. Someone who actually knows this code should take a look before anything is comitted - consider the below (not much more than) a bug report. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: Clemens Ladisch <clemens@ladisch.de Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-14ALSA: oxygen: Xonar DG: fix CS4245 register writesClemens Ladisch1-1/+1
Accidentally exchanging register addresses and register values leads to many strange errors ... Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-12ALSA: oxygen: fix Xonar DG inputClemens Ladisch1-1/+1
Apparently, this card uses the other I2S input. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-11ALSA: oxygen: add S/PDIF source selection for Claro cardsClemens Ladisch1-4/+88
Add a mixer control to switch between the optical and coaxial S/PDIF inputs on the HT-Omega Claro and Claro halo cards. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-11ALSA: oxygen: fix CD/MIDI for X-Meridian (2G)Clemens Ladisch1-0/+3
Enable the X-Meridian's CD input and the X-Meridian 2G's potential MIDI ports. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-11ALSA: include delay.h for msleep in Xonar DG supportStephen Rothwell1-0/+1
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: add some card namesClemens Ladisch1-3/+21
Instead of the generic Oxygen, use the actual card name, if known. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: do not show chip revision in card longnameClemens Ladisch2-9/+3
Apparently, the revision is 2 on all sold sound cards, so this information is not actually useful. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: X-Meridian: add S/PDIF source selectionClemens Ladisch1-2/+75
Add a mixer control to select between the on-board and extension board S/PDIF inputs for the X-Meridian (2G). Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: add digital input validity check switchClemens Ladisch1-10/+20
Add a mixer control to prevent capturing S/PDIF samples that are not marked as valid (non-audio or corrupted samples). Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: core, oxygen, virtuoso: add an enum control info helperClemens Ladisch6-102/+16
Introduce the helper function snd_ctl_enum_info() to fill out the elem_info fields for an enumerated control. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: add Xonar HDAV1.3 Slim supportClemens Ladisch3-14/+204
Add experimental support for the Asus Xonar HDAV1.3 Slim sound card. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: add Xonar DG supportClemens Ladisch6-4/+731
Add experimental support for the Asus Xonar DG sound card. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: add X-Meridian 2G supportClemens Ladisch1-0/+2
Add support for the AuzenTech X-Meridian 7.1 2G sound card. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: add more PCI IDsClemens Ladisch1-0/+3
Add PCI IDs for some unknown models. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: reduce MCLK in double rate modesClemens Ladisch3-7/+9
For the CSxxxx and AKxxxx DAC/ADC chips, the MCLK factor in double rate modes (64-96 kHz) can be reduced to 128x without reducing sound quality. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: simplify model-specific MCLK handlingClemens Ladisch8-95/+89
Replace the get_i2s_mclk callback with tables of MCLK values. This simplifies the MCLK-handling code in both the framework and the model- specific drivers. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: use headphone gain setting only on front DACClemens Ladisch1-0/+2
Do not apply the headphone gain offset to any but the front DAC. These DACs would not be used in headphone mode, so this saves a few register writes. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: handle DAC oversampling automaticallyClemens Ladisch1-79/+21
Remove the DAC Oversampling mixer control because this setting does not make much sense. For cards with the H6 daughterboard, 128x oversampling was disabled anyway because these high MCLK frequency would not be compatible with the connector cable. For cards without the H6 daughterboard, 128x gives a slightly higher output quality; there is no reason to reduce it to 64x except for saving power, but then these cards have not been designed to be power efficient anyway (the D2's blinkenlights cannot be disabled). Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: use lower master clock with H6 daughterboardClemens Ladisch1-13/+18
Because of the unshielded connector cable, it is important to use as low a master clock frequency as possible with the H6. For double rate modes (64-96 kHz), the MCLK rate is unconditionally lowered from 512x to 256x because the higher rate would not improve anything. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: configure correct master clock frequency on the CS2000Clemens Ladisch1-13/+12
The clock output of the CS2000, which is used as master clock for the DACs, was using half the actual master clock frequency for some reason. Using the theoretically correct frequency seems also to work in practice. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: remove non-working controls on Essence ST DeluxeClemens Ladisch1-6/+22
On the Xonar Essence ST Deluxe, remove all mixer controls that would require I2C communication with the third DAC, which does not work because of an addressing conflict with the CS2000 chip. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: change PCM1796 format to I2SClemens Ladisch1-5/+5
Change the PCM format used for the PCM1796 from left-justified to I2S to ensure that the correct format is used even for the Essence ST Deluxe's center/LFE DAC, where I2C does not work because of an address conflict with the CS2000 chip. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: wait for PCM1796 clock to become stableClemens Ladisch1-0/+5
The PCM1796 needs the master clock for I2C communication to work, so add delays after clock changes to ensure that the clock is stable when we try to write the DACs' registers. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: virtuoso: do not use fast I2C speedClemens Ladisch1-2/+2
To make the I2C communication reliable when using the H6 daughterboard, reduce the I2C clock frequency. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: fix SPI clocks slower than 6.25 MHzClemens Ladisch2-6/+6
Fix wrong register bits for SPI clock cycle times longer than 160 ns, and adjust the polling loop timeout for these speeds. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: remove oxygen_model::private_data fieldClemens Ladisch2-5/+2
The number of DACs can now be deduced from the dac_channels_mixer field, so the private_data field is no longer needed. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2011-01-10ALSA: oxygen: allow different number of PCM and mixer channelsClemens Ladisch7-15/+25
For cards like the Xonar HDAV1.3, differentiate between the number of PCM channels that can be played and the number of channels whose volume can be adjusted. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-13Merge branch 'topic/workq-update' into topic/miscTakashi Iwai1-2/+4
2010-12-13sound: don't use flush_scheduled_work()Tejun Heo1-2/+4
flush_scheduled_work() is deprecated and scheduled to be removed. * cancel[_delayed]_work() + flush_scheduled_work() -> cancel[_delayed]_work_sync(). * wm8350, wm8753 and soc-core use custom code to cancel a delayed work, execute it immediately if it was pending and wait for its completion. This is equivalent to flush_delayed_work_sync(). Use it instead. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: oxygen: update hardware commentsClemens Ladisch4-94/+154
Reformat and update the comments that describe the hardware connections on the various models. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: oxygen: show correct package IDClemens Ladisch1-1/+7
Instead of the hardcoded "CMI8788", show the actual chip name. Note: This is neither what the chip is (it's always the same), nor what the chip is actually called. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: oxygen: allow to dump codec registersClemens Ladisch6-11/+151
To help with debugging, add the registers of the model-specific codecs to the controller and AC97 register dump in the proc file. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: virtuoso: fix front panel routing for D1/DX/ST(X)Clemens Ladisch4-6/+62
The "Front Panel" switch on the Xonar D1/DX actually switches only the output direction, so mark it appropriately. The front panel microphone is controlled by the FMIC2MIC bit of the CM9780. It was unconditionally enabled on the D1/DX and never set on the ST(X); add a control for it. Selecting the front panel microphone as source does not actually disable the microphone jack, but this is bug-compatible with the Windows driver, and users rely on it. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: virtuoso: add HDMI enable switch for HDAV1.3Clemens Ladisch3-3/+24
The GPIO bit that enables analog output on the Xonar HDAV1.3 also disables the HDMI audio output, so we better add a switch for it. Hopefully, this is sufficient to make the HDMI output work. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-06ALSA: virtuoso: initialize unknown GPIO bitsClemens Ladisch2-3/+10
Initialize the configuration of some unknown GPIO output bits (that might not be used at all) to be the same as in the Windows driver, just to be sure. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-11-22ALSA: oxygen: support for period wakeup disablingClemens Ladisch1-4/+10
Allow disabling period wakeup interrupts for all PCM streams. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-11-03ALSA: oxygen: add HiFier Serenade supportClemens Ladisch1-13/+14
Add support for the TempoTec/MediaTek HiFier Serenade sound card. The PCI ID was already there, but the driver handled it like the Fantasia model, which resulted in a dummy recording device. As a stereo output-only card, this model is to be handled exactly like the HG2PCI. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-11-03ALSA: oxygen: reorganize PCI IDsClemens Ladisch1-8/+14
Sort the PCI IDs so that they make logical sense. Also move the card name comments into this list because the model symbols should be (more) self-explanationary. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-11-03ALSA: oxygen: add Kuroutoshikou CMI8787-HG2PCI supportClemens Ladisch2-5/+16
Add support for the Kuroutoshikou CMI8787-HG2PCI sound card. [replaced non-latin letters in the patch by tiwai] Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-11-03ALSA: oxygen: merge HiFier driver into snd-oxygenClemens Ladisch3-246/+38
The snd-hifier driver contains more duplicated code than model-specific code, so it does not make sense for it to be a separate driver. Handling the two-channel output restriction can be easily done in the generic driver. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-11 13:52:12 +0000