| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 338f977f4eb441e69bb9a46eaa0ac715c931a67f upstream.
The "new" fragmentation code (since my rewrite almost 5 years ago)
erroneously sets skb->len rather than using skb_trim() to adjust
the length of the first fragment after copying out all the others.
This leaves the skb tail pointer pointing to after where the data
originally ended, and thus causes the encryption MIC to be written
at that point, rather than where it belongs: immediately after the
data.
The impact of this is that if software encryption is done, then
a) encryption doesn't work for the first fragment, the connection
becomes unusable as the first fragment will never be properly
verified at the receiver, the MIC is practically guaranteed to
be wrong
b) we leak up to 8 bytes of plaintext (!) of the packet out into
the air
This is only mitigated by the fact that many devices are capable
of doing encryption in hardware, in which case this can't happen
as the tail pointer is irrelevant in that case. Additionally,
fragmentation is not used very frequently and would normally have
to be configured manually.
Fix this by using skb_trim() properly.
Fixes: 2de8e0d999b8 ("mac80211: rewrite fragmentation")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0297ea17bf7879fb5846fafd1be4c0471e72848d upstream.
When the driver cannot start the AP or when the assignement
of the beacon goes wrong, we need to unassign the vif.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2f617435c3a6fe3f39efb9ae2baa77de2d6c97b8 upstream.
ieee80211_start_roc_work() might add a new roc
to existing roc, and tell cfg80211 it has already
started.
However, this might happen before the roc cookie
was set, resulting in REMAIN_ON_CHANNEL (started)
event with null cookie. Consequently, it can make
wpa_supplicant go out of sync.
Fix it by setting the roc cookie earlier.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ff33b7dd0228b7d7ed44791bbbc98b03fd15d9d upstream.
When a task enters call_refreshresult with status 0 from call_refresh and
!rpcauth_uptodatecred(task) it enters call_refresh again with no rate-limiting
or max number of retries.
Instead of trying forever, make use of the retry path that other errors use.
This only seems to be possible when the crrefresh callback is gss_refresh_null,
which only happens when destroying the context.
To reproduce:
1) mount with sec=krb5 (or sec=sys with krb5 negotiated for non FSID specific
operations).
2) reboot - the client will be stuck and will need to be hard rebooted
BUG: soft lockup - CPU#0 stuck for 22s! [kworker/0:2:46]
Modules linked in: rpcsec_gss_krb5 nfsv4 nfs fscache ppdev crc32c_intel aesni_intel aes_x86_64 glue_helper lrw gf128mul ablk_helper cryptd serio_raw i2c_piix4 i2c_core e1000 parport_pc parport shpchp nfsd auth_rpcgss oid_registry exportfs nfs_acl lockd sunrpc autofs4 mptspi scsi_transport_spi mptscsih mptbase ata_generic floppy
irq event stamp: 195724
hardirqs last enabled at (195723): [<ffffffff814a925c>] restore_args+0x0/0x30
hardirqs last disabled at (195724): [<ffffffff814b0a6a>] apic_timer_interrupt+0x6a/0x80
softirqs last enabled at (195722): [<ffffffff8103f583>] __do_softirq+0x1df/0x276
softirqs last disabled at (195717): [<ffffffff8103f852>] irq_exit+0x53/0x9a
CPU: 0 PID: 46 Comm: kworker/0:2 Not tainted 3.13.0-rc3-branch-dros_testing+ #4
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/31/2013
Workqueue: rpciod rpc_async_schedule [sunrpc]
task: ffff8800799c4260 ti: ffff880079002000 task.ti: ffff880079002000
RIP: 0010:[<ffffffffa0064fd4>] [<ffffffffa0064fd4>] __rpc_execute+0x8a/0x362 [sunrpc]
RSP: 0018:ffff880079003d18 EFLAGS: 00000246
RAX: 0000000000000005 RBX: 0000000000000007 RCX: 0000000000000007
RDX: 0000000000000007 RSI: ffff88007aecbae8 RDI: ffff8800783d8900
RBP: ffff880079003d78 R08: ffff88006e30e9f8 R09: ffffffffa005a3d7
R10: ffff88006e30e7b0 R11: ffff8800783d8900 R12: ffffffffa006675e
R13: ffff880079003ce8 R14: ffff88006e30e7b0 R15: ffff8800783d8900
FS: 0000000000000000(0000) GS:ffff88007f200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3072333000 CR3: 0000000001a0b000 CR4: 00000000001407f0
Stack:
ffff880079003d98 0000000000000246 0000000000000000 ffff88007a9a4830
ffff880000000000 ffffffff81073f47 ffff88007f212b00 ffff8800799c4260
ffff8800783d8988 ffff88007f212b00 ffffe8ffff604800 0000000000000000
Call Trace:
[<ffffffff81073f47>] ? trace_hardirqs_on_caller+0x145/0x1a1
[<ffffffffa00652d3>] rpc_async_schedule+0x27/0x32 [sunrpc]
[<ffffffff81052974>] process_one_work+0x211/0x3a5
[<ffffffff810528d5>] ? process_one_work+0x172/0x3a5
[<ffffffff81052eeb>] worker_thread+0x134/0x202
[<ffffffff81052db7>] ? rescuer_thread+0x280/0x280
[<ffffffff81052db7>] ? rescuer_thread+0x280/0x280
[<ffffffff810584a0>] kthread+0xc9/0xd1
[<ffffffff810583d7>] ? __kthread_parkme+0x61/0x61
[<ffffffff814afd6c>] ret_from_fork+0x7c/0xb0
[<ffffffff810583d7>] ? __kthread_parkme+0x61/0x61
Code: e8 87 63 fd e0 c6 05 10 dd 01 00 01 48 8b 43 70 4c 8d 6b 70 45 31 e4 a8 02 0f 85 d5 02 00 00 4c 8b 7b 48 48 c7 43 48 00 00 00 00 <4c> 8b 4b 50 4d 85 ff 75 0c 4d 85 c9 4d 89 cf 0f 84 32 01 00 00
And the output of "rpcdebug -m rpc -s all":
RPC: 61 call_refresh (status 0)
RPC: 61 call_refresh (status 0)
RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0
RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0
RPC: 61 call_refreshresult (status 0)
RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0
RPC: 61 call_refreshresult (status 0)
RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0
RPC: 61 call_refresh (status 0)
RPC: 61 call_refreshresult (status 0)
RPC: 61 call_refresh (status 0)
RPC: 61 call_refresh (status 0)
RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0
RPC: 61 call_refreshresult (status 0)
RPC: 61 call_refresh (status 0)
RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0
RPC: 61 call_refresh (status 0)
RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0
RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0
RPC: 61 call_refreshresult (status 0)
RPC: 61 call_refresh (status 0)
RPC: 61 call_refresh (status 0)
RPC: 61 call_refresh (status 0)
RPC: 61 call_refresh (status 0)
RPC: 61 call_refreshresult (status 0)
RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28a625cbc2a14f17b83e47ef907b2658576a32aa upstream.
Having this struct in module memory could Oops when if the module is
unloaded while the buffer still persists in a pipe.
Since sock_pipe_buf_ops is essentially the same as fuse_dev_pipe_buf_steal
merge them into nosteal_pipe_buf_ops (this is the same as
default_pipe_buf_ops except stealing the page from the buffer is not
allowed).
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ No relevant upstream commit. ]
This problem was fixed upstream by commit 1e9f3d6f1c40 ("ip6tnl: fix use after
free of fb_tnl_dev").
The upstream patch depends on upstream commit 0bd8762824e7 ("ip6tnl: add x-netns
support"), which was not backported into 3.10 branch.
First, explain the problem: when the ip6_tunnel module is unloaded,
ip6_tunnel_cleanup() is called.
rmmod ip6_tunnel
=> ip6_tunnel_cleanup()
=> rtnl_link_unregister()
=> __rtnl_kill_links()
=> for_each_netdev(net, dev) {
if (dev->rtnl_link_ops == ops)
ops->dellink(dev, &list_kill);
}
At this point, the FB device is deleted (and all ip6tnl tunnels).
=> unregister_pernet_device()
=> unregister_pernet_operations()
=> ops_exit_list()
=> ip6_tnl_exit_net()
=> ip6_tnl_destroy_tunnels()
=> t = rtnl_dereference(ip6n->tnls_wc[0]);
unregister_netdevice_queue(t->dev, &list);
We delete the FB device a second time here!
The previous fix removes these lines, which fix this double free. But the patch
introduces a memory leak when a netns is destroyed, because the FB device is
never deleted. By adding an rtnl ops which delete all ip6tnl device excepting
the FB device, we can keep this exlicit removal in ip6_tnl_destroy_tunnels().
CC: Steven Rostedt <rostedt@goodmis.org>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Steven Rostedt <srostedt@redhat.com>
Tested-by: Steven Rostedt <srostedt@redhat.com> (and our entire MRG team)
Tested-by: "Luis Claudio R. Goncalves" <lgoncalv@redhat.com>
Tested-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ No relevant upstream commit. ]
This reverts commit 22c3ec552c29cf4bd4a75566088950fe57d860c4.
This patch is not the right fix, it introduces a memory leak when a netns is
destroyed (the FB device is never deleted).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Steven Rostedt <srostedt@redhat.com>
Tested-by: Steven Rostedt <srostedt@redhat.com> (and our entire MRG team)
Tested-by: "Luis Claudio R. Goncalves" <lgoncalv@redhat.com>
Tested-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ No relevant upstream commit. ]
This problem was fixed upstream by commit 9434266f2c64 ("sit: fix use after free
of fb_tunnel_dev").
The upstream patch depends on upstream commit 5e6700b3bf98 ("sit: add support of
x-netns"), which was not backported into 3.10 branch.
First, explain the problem: when the sit module is unloaded, sit_cleanup() is
called.
rmmod sit
=> sit_cleanup()
=> rtnl_link_unregister()
=> __rtnl_kill_links()
=> for_each_netdev(net, dev) {
if (dev->rtnl_link_ops == ops)
ops->dellink(dev, &list_kill);
}
At this point, the FB device is deleted (and all sit tunnels).
=> unregister_pernet_device()
=> unregister_pernet_operations()
=> ops_exit_list()
=> sit_exit_net()
=> sit_destroy_tunnels()
In this function, no tunnel is found.
=> unregister_netdevice_queue(sitn->fb_tunnel_dev, &list);
We delete the FB device a second time here!
Because we cannot simply remove the second deletion (sit_exit_net() must remove
the FB device when a netns is deleted), we add an rtnl ops which delete all sit
device excepting the FB device and thus we can keep the explicit deletion in
sit_exit_net().
CC: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reported-by: Steven Rostedt <srostedt@redhat.com>
Tested-by: Steven Rostedt <srostedt@redhat.com> (and our entire MRG team)
Tested-by: "Luis Claudio R. Goncalves" <lgoncalv@redhat.com>
Tested-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a452ce345d63ddf92cd101e4196569f8718ad319 ]
I see a memory leak when using a transparent HTTP proxy using TPROXY
together with TCP early demux and Kernel v3.8.13.15 (Ubuntu stable):
unreferenced object 0xffff88008cba4a40 (size 1696):
comm "softirq", pid 0, jiffies 4294944115 (age 8907.520s)
hex dump (first 32 bytes):
0a e0 20 6a 40 04 1b 37 92 be 32 e2 e8 b4 00 00 .. j@..7..2.....
02 00 07 01 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff810b710a>] kmem_cache_alloc+0xad/0xb9
[<ffffffff81270185>] sk_prot_alloc+0x29/0xc5
[<ffffffff812702cf>] sk_clone_lock+0x14/0x283
[<ffffffff812aaf3a>] inet_csk_clone_lock+0xf/0x7b
[<ffffffff8129a893>] netlink_broadcast+0x14/0x16
[<ffffffff812c1573>] tcp_create_openreq_child+0x1b/0x4c3
[<ffffffff812c033e>] tcp_v4_syn_recv_sock+0x38/0x25d
[<ffffffff812c13e4>] tcp_check_req+0x25c/0x3d0
[<ffffffff812bf87a>] tcp_v4_do_rcv+0x287/0x40e
[<ffffffff812a08a7>] ip_route_input_noref+0x843/0xa55
[<ffffffff812bfeca>] tcp_v4_rcv+0x4c9/0x725
[<ffffffff812a26f4>] ip_local_deliver_finish+0xe9/0x154
[<ffffffff8127a927>] __netif_receive_skb+0x4b2/0x514
[<ffffffff8127aa77>] process_backlog+0xee/0x1c5
[<ffffffff8127c949>] net_rx_action+0xa7/0x200
[<ffffffff81209d86>] add_interrupt_randomness+0x39/0x157
But there are many more, resulting in the machine going OOM after some
days.
From looking at the TPROXY code, and with help from Florian, I see
that the memory leak is introduced in tcp_v4_early_demux():
void tcp_v4_early_demux(struct sk_buff *skb)
{
/* ... */
iph = ip_hdr(skb);
th = tcp_hdr(skb);
if (th->doff < sizeof(struct tcphdr) / 4)
return;
sk = __inet_lookup_established(dev_net(skb->dev), &tcp_hashinfo,
iph->saddr, th->source,
iph->daddr, ntohs(th->dest),
skb->skb_iif);
if (sk) {
skb->sk = sk;
where the socket is assigned unconditionally to skb->sk, also bumping
the refcnt on it. This is problematic, because in our case the skb
has already a socket assigned in the TPROXY target. This then results
in the leak I see.
The very same issue seems to be with IPv6, but haven't tested.
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a0065f266a9b5d51575535a25c15ccbeed9a9966 ]
The two commits 0115e8e30d (net: remove delay at device dismantle) and
748e2d9396a (net: reinstate rtnl in call_netdevice_notifiers()) silently
removed a NULL pointer check for in_dev since Linux 3.7.
This patch re-introduces this check as it causes crashing the kernel when
setting small mtu values on non-ip capable netdevices.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 11c21a307d79ea5f6b6fc0d3dfdeda271e5e65f6 ]
commit a622260254ee48("ip_tunnel: fix kernel panic with icmp_dest_unreach")
clear IPCB in ip_tunnel_xmit() , or else skb->cb[] may contain garbage from
GSO segmentation layer.
But commit 0e6fbc5b6c621("ip_tunnels: extend iptunnel_xmit()") refactor codes,
and it clear IPCB behind the dst_link_failure().
So clear IPCB in ip_tunnel_xmit() just like commti a622260254ee48("ip_tunnel:
fix kernel panic with icmp_dest_unreach").
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aee636c4809fa54848ff07a899b326eb1f9987a2 ]
At first Jakub Zawadzki noticed that some divisions by reciprocal_divide
were not correct. (off by one in some cases)
http://www.wireshark.org/~darkjames/reciprocal-buggy.c
He could also show this with BPF:
http://www.wireshark.org/~darkjames/set-and-dump-filter-k-bug.c
The reciprocal divide in linux kernel is not generic enough,
lets remove its use in BPF, as it is not worth the pain with
current cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Daniel Borkmann <dxchgb@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Matt Evans <matt@ozlabs.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 77f99ad16a07aa062c2d30fae57b1fee456f6ef6 ]
Because the tcp-metrics is an RCU-list, it may be that two
soft-interrupts are inside __tcp_get_metrics() for the same
destination-IP at the same time. If this destination-IP is not yet part of
the tcp-metrics, both soft-interrupts will end up in tcpm_new and create
a new entry for this IP.
So, we will have two tcp-metrics with the same destination-IP in the list.
This patch checks twice __tcp_get_metrics(). First without holding the
lock, then while holding the lock. The second one is there to confirm
that the entry has not been added by another soft-irq while waiting for
the spin-lock.
Fixes: 51c5d0c4b169b (tcp: Maintain dynamic metrics in local cache.)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c196403b79aa241c3fefb3ee5bb328aa7c5cc860 ]
commit ae4b46e9d "net: rds: use this_cpu_* per-cpu helper" broke per-cpu
handling for rds. chpfirst is the result of __this_cpu_read(), so it is
an absolute pointer and not __percpu. Therefore, __this_cpu_write()
should not operate on chpfirst, but rather on cache->percpu->first, just
like __this_cpu_read() did before.
Signed-off-byd Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 95f4a45de1a0f172b35451fc52283290adb21f6e ]
Bob Falken reported that after 4G packets, multicast forwarding stopped
working. This was because of a rule reference counter overflow which
freed the rule as soon as the overflow happend.
This patch solves this by adding the FIB_LOOKUP_NOREF flag to
fib_rules_lookup calls. This is safe even from non-rcu locked sections
as in this case the flag only implies not taking a reference to the rule,
which we don't need at all.
Rules only hold references to the namespace, which are guaranteed to be
available during the call of the non-rcu protected function reg_vif_xmit
because of the interface reference which itself holds a reference to
the net namespace.
Fixes: f0ad0860d01e47 ("ipv4: ipmr: support multiple tables")
Fixes: d1db275dd3f6e4 ("ipv6: ip6mr: support multiple tables")
Reported-by: Bob Falken <NetFestivalHaveFun@gmx.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 267d29a69c6af39445f36102a832b25ed483f299 ]
Fix a memory leak in the ieee802154_add_iface() error handling path.
Detected by Coverity: CID 710490.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Based upon upstream commit 70315d22d3c7383f9a508d0aab21e2eb35b2303a ]
Fix inet_diag_dump_icsk() to reflect the fact that both TIME_WAIT and
FIN_WAIT2 connections are represented by inet_timewait_sock (not just
TIME_WAIT). Thus:
(a) We need to iterate through the time_wait buckets if the user wants
either TIME_WAIT or FIN_WAIT2. (Before fixing this, "ss -nemoi state
fin-wait-2" would not return any sockets, even if there were some in
FIN_WAIT2.)
(b) We need to check tw_substate to see if the user wants to dump
sockets in the particular substate (TIME_WAIT or FIN_WAIT2) that a
given connection is in. (Before fixing this, "ss -nemoi state
time-wait" would actually return sockets in state FIN_WAIT2.)
An analogous fix is in v3.13: 70315d22d3c7383f9a508d0aab21e2eb35b2303a
("inet_diag: fix inet_diag_dump_icsk() to use correct state for
timewait sockets") but that patch is quite different because 3.13 code
is very different in this area due to the unification of TCP hash
tables in 05dbc7b ("tcp/dccp: remove twchain") in v3.13-rc1.
I tested that this applies cleanly between v3.3 and v3.12, and tested
that it works in both 3.3 and 3.12. It does not apply cleanly to 3.2
and earlier (though it makes semantic sense), and semantically is not
the right fix for 3.13 and beyond (as mentioned above).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2def2ef2ae5f3990aabdbe8a755911902707d268 upstream.
The x32 case for the recvmsg() timout handling is broken:
asmlinkage long compat_sys_recvmmsg(int fd, struct compat_mmsghdr __user *mmsg,
unsigned int vlen, unsigned int flags,
struct compat_timespec __user *timeout)
{
int datagrams;
struct timespec ktspec;
if (flags & MSG_CMSG_COMPAT)
return -EINVAL;
if (COMPAT_USE_64BIT_TIME)
return __sys_recvmmsg(fd, (struct mmsghdr __user *)mmsg, vlen,
flags | MSG_CMSG_COMPAT,
(struct timespec *) timeout);
...
The timeout pointer parameter is provided by userland (hence the __user
annotation) but for x32 syscalls it's simply cast to a kernel pointer
and is passed to __sys_recvmmsg which will eventually directly
dereference it for both reading and writing. Other callers to
__sys_recvmmsg properly copy from userland to the kernel first.
The bug was introduced by commit ee4fa23c4bfc ("compat: Use
COMPAT_USE_64BIT_TIME in net/compat.c") and should affect all kernels
since 3.4 (and perhaps vendor kernels if they backported x32 support
along with this code).
Note that CONFIG_X86_X32_ABI gets enabled at build time and only if
CONFIG_X86_X32 is enabled and ld can build x32 executables.
Other uses of COMPAT_USE_64BIT_TIME seem fine.
This addresses CVE-2014-0038.
Signed-off-by: PaX Team <pageexec@freemail.hu>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2690d97ade05c5325cbf7c72b94b90d265659886 upstream.
Commit 5901b6be885e attempted to introduce IPv6 support into
IRC NAT helper. By doing so, the following code seemed to be removed
by accident:
ip = ntohl(exp->master->tuplehash[IP_CT_DIR_REPLY].tuple.dst.u3.ip);
sprintf(buffer, "%u %u", ip, port);
pr_debug("nf_nat_irc: inserting '%s' == %pI4, port %u\n", buffer, &ip, port);
This leads to the fact that buffer[] was left uninitialized and
contained some stack value. When we call nf_nat_mangle_tcp_packet(),
we call strlen(buffer) on excatly this uninitialized buffer. If we
are unlucky and the skb has enough tailroom, we overwrite resp. leak
contents with values that sit on our stack into the packet and send
that out to the receiver.
Since the rather informal DCC spec [1] does not seem to specify
IPv6 support right now, we log such occurences so that admins can
act accordingly, and drop the packet. I've looked into XChat source,
and IPv6 is not supported there: addresses are in u32 and print
via %u format string.
Therefore, restore old behaviour as in IPv4, use snprintf(). The
IRC helper does not support IPv6 by now. By this, we can safely use
strlen(buffer) in nf_nat_mangle_tcp_packet() and prevent a buffer
overflow. Also simplify some code as we now have ct variable anyway.
[1] http://www.irchelp.org/irchelp/rfc/ctcpspec.html
Fixes: 5901b6be885e ("netfilter: nf_nat: support IPv6 in IRC NAT helper")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 277d916fc2e959c3f106904116bb4f7b1148d47a upstream.
The check needs to apply to both multicast and unicast packets,
otherwise probe requests on AP mode scans are sent through the multicast
buffer queue, which adds long delays (often longer than the scanning
interval).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1cdbcb7957cf9e5f841dbcde9b38fd18a804208b ]
This is a generic solution to resolve a specific problem that I have observed.
If the encapsulation of an skb changes then ability to offload checksums
may also change. In particular it may be necessary to perform checksumming
in software.
An example of such a case is where a non-GRE packet is received but
is to be encapsulated and transmitted as GRE.
Another example relates to my proposed support for for packets
that are non-MPLS when received but MPLS when transmitted.
The cost of this change is that the value of the csum variable may be
checked when it previously was not. In the case where the csum variable is
true this is pure overhead. In the case where the csum variable is false it
leads to software checksumming, which I believe also leads to correct
checksums in transmitted packets for the cases described above.
Further analysis:
This patch relies on the return value of can_checksum_protocol()
being correct and in turn the return value of skb_network_protocol(),
used to provide the protocol parameter of can_checksum_protocol(),
being correct. It also relies on the features passed to skb_segment()
and in turn to can_checksum_protocol() being correct.
I believe that this problem has not been observed for VLANs because it
appears that almost all drivers, the exception being xgbe, set
vlan_features such that that the checksum offload support for VLAN packets
is greater than or equal to that of non-VLAN packets.
I wonder if the code in xgbe may be an oversight and the hardware does
support checksumming of VLAN packets. If so it may be worth updating the
vlan_features of the driver as this patch will force such checksums to be
performed in software rather than hardware.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fe0d692bbc645786bce1a98439e548ae619269f5 ]
br_multicast_set_hash_max() is called from process context in
net/bridge/br_sysfs_br.c by the sysfs store_hash_max() function.
br_multicast_set_hash_max() calls spin_lock(&br->multicast_lock),
which can deadlock the CPU if a softirq that also tries to take the
same lock interrupts br_multicast_set_hash_max() while the lock is
held . This can happen quite easily when any of the bridge multicast
timers expire, which try to take the same lock.
The fix here is to use spin_lock_bh(), preventing other softirqs from
executing on this CPU.
Steps to reproduce:
1. Create a bridge with several interfaces (I used 4).
2. Set the "multicast query interval" to a low number, like 2.
3. Enable the bridge as a multicast querier.
4. Repeatedly set the bridge hash_max parameter via sysfs.
# brctl addbr br0
# brctl addif br0 eth1 eth2 eth3 eth4
# brctl setmcqi br0 2
# brctl setmcquerier br0 1
# while true ; do echo 4096 > /sys/class/net/br0/bridge/hash_max; done
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit aca5f58f9ba803ec8c2e6bcf890db17589e8dfcc ]
The VLAN tag handling code in netpoll_send_skb_on_dev() has two problems.
1) It exits without unlocking the TXQ.
2) It then tries to queue a NULL skb to npinfo->txq.
Reported-by: Ahmed Tamrawi <atamrawi@iastate.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4d231b76eef6c4a6bd9c96769e191517765942cb ]
While commit 30a584d944fb fixes datagram interface in LLC, a use
after free bug has been introduced for SOCK_STREAM sockets that do
not make use of MSG_PEEK.
The flow is as follow ...
if (!(flags & MSG_PEEK)) {
...
sk_eat_skb(sk, skb, false);
...
}
...
if (used + offset < skb->len)
continue;
... where sk_eat_skb() calls __kfree_skb(). Therefore, cache
original length and work on skb_len to check partial reads.
Fixes: 30a584d944fb ("[LLX]: SOCK_DGRAM interface fixes")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2205369a314e12fcec4781cc73ac9c08fc2b47de ]
When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.
But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.
This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.
Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.
To facilitate this add a dev_rebuild_header(). There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP). So we need a helper function just like
dev_hard_header() to avoid crashes.
Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.
With lots of help from Florian Westphal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f81152e35001e91997ec74a7b4e040e6ab0acccf ]
recvmsg handler in net/rose/af_rose.c performs size-check ->msg_namelen.
After commit f3d3342602f8bcbf37d7c46641cb9bca7618eb1c
(net: rework recvmsg handler msg_name and msg_namelen logic), we now
always take the else branch due to namelen being initialized to 0.
Digging in netdev-vger-cvs git repo shows that msg_namelen was
initialized with a fixed-size since at least 1995, so the else branch
was never taken.
Compile tested only.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c2349758acf1874e4c2b93fe41d072336f1a31d0 ]
Binding might result in a NULL device, which is dereferenced
causing this BUG:
[ 1317.260548] BUG: unable to handle kernel NULL pointer dereference at 000000000000097
4
[ 1317.261847] IP: [<ffffffff84225f52>] rds_ib_laddr_check+0x82/0x110
[ 1317.263315] PGD 418bcb067 PUD 3ceb21067 PMD 0
[ 1317.263502] Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
[ 1317.264179] Dumping ftrace buffer:
[ 1317.264774] (ftrace buffer empty)
[ 1317.265220] Modules linked in:
[ 1317.265824] CPU: 4 PID: 836 Comm: trinity-child46 Tainted: G W 3.13.0-rc4-
next-20131218-sasha-00013-g2cebb9b-dirty #4159
[ 1317.267415] task: ffff8803ddf33000 ti: ffff8803cd31a000 task.ti: ffff8803cd31a000
[ 1317.268399] RIP: 0010:[<ffffffff84225f52>] [<ffffffff84225f52>] rds_ib_laddr_check+
0x82/0x110
[ 1317.269670] RSP: 0000:ffff8803cd31bdf8 EFLAGS: 00010246
[ 1317.270230] RAX: 0000000000000000 RBX: ffff88020b0dd388 RCX: 0000000000000000
[ 1317.270230] RDX: ffffffff8439822e RSI: 00000000000c000a RDI: 0000000000000286
[ 1317.270230] RBP: ffff8803cd31be38 R08: 0000000000000000 R09: 0000000000000000
[ 1317.270230] R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
[ 1317.270230] R13: 0000000054086700 R14: 0000000000a25de0 R15: 0000000000000031
[ 1317.270230] FS: 00007ff40251d700(0000) GS:ffff88022e200000(0000) knlGS:000000000000
0000
[ 1317.270230] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 1317.270230] CR2: 0000000000000974 CR3: 00000003cd478000 CR4: 00000000000006e0
[ 1317.270230] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1317.270230] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000090602
[ 1317.270230] Stack:
[ 1317.270230] 0000000054086700 5408670000a25de0 5408670000000002 0000000000000000
[ 1317.270230] ffffffff84223542 00000000ea54c767 0000000000000000 ffffffff86d26160
[ 1317.270230] ffff8803cd31be68 ffffffff84223556 ffff8803cd31beb8 ffff8800c6765280
[ 1317.270230] Call Trace:
[ 1317.270230] [<ffffffff84223542>] ? rds_trans_get_preferred+0x42/0xa0
[ 1317.270230] [<ffffffff84223556>] rds_trans_get_preferred+0x56/0xa0
[ 1317.270230] [<ffffffff8421c9c3>] rds_bind+0x73/0xf0
[ 1317.270230] [<ffffffff83e4ce62>] SYSC_bind+0x92/0xf0
[ 1317.270230] [<ffffffff812493f8>] ? context_tracking_user_exit+0xb8/0x1d0
[ 1317.270230] [<ffffffff8119313d>] ? trace_hardirqs_on+0xd/0x10
[ 1317.270230] [<ffffffff8107a852>] ? syscall_trace_enter+0x32/0x290
[ 1317.270230] [<ffffffff83e4cece>] SyS_bind+0xe/0x10
[ 1317.270230] [<ffffffff843a6ad0>] tracesys+0xdd/0xe2
[ 1317.270230] Code: 00 8b 45 cc 48 8d 75 d0 48 c7 45 d8 00 00 00 00 66 c7 45 d0 02 00
89 45 d4 48 89 df e8 78 49 76 ff 41 89 c4 85 c0 75 0c 48 8b 03 <80> b8 74 09 00 00 01 7
4 06 41 bc 9d ff ff ff f6 05 2a b6 c2 02
[ 1317.270230] RIP [<ffffffff84225f52>] rds_ib_laddr_check+0x82/0x110
[ 1317.270230] RSP <ffff8803cd31bdf8>
[ 1317.270230] CR2: 0000000000000974
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 24f5b855e17df7e355eacd6c4a12cc4d6a6c9ff0 ]
ip6_rt_copy only sets dst.from if ort has flag RTF_ADDRCONF and RTF_DEFAULT.
but the prefix routes which did get installed by hand locally can have an
expiration, and no any flag combination which can ensure a potential from
does never expire, so we should always set the new created dst's from.
This also fixes the new created dst is always expired since the ort, which
is created by RA, maybe has RTF_EXPIRES and RTF_ADDRCONF, but no RTF_DEFAULT.
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
CC: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b1aac815c0891fe4a55a6b0b715910142227700f ]
Jakub reported while working with nlmon netlink sniffer that parts of
the inet_diag_sockid are not initialized when r->idiag_family != AF_INET6.
That is, fields of r->id.idiag_src[1 ... 3], r->id.idiag_dst[1 ... 3].
In fact, it seems that we can leak 6 * sizeof(u32) byte of kernel [slab]
memory through this. At least, in udp_dump_one(), we allocate a skb in ...
rep = nlmsg_new(sizeof(struct inet_diag_msg) + ..., GFP_KERNEL);
... and then pass that to inet_sk_diag_fill() that puts the whole struct
inet_diag_msg into the skb, where we only fill out r->id.idiag_src[0],
r->id.idiag_dst[0] and leave the rest untouched:
r->id.idiag_src[0] = inet->inet_rcv_saddr;
r->id.idiag_dst[0] = inet->inet_daddr;
struct inet_diag_msg embeds struct inet_diag_sockid that is correctly /
fully filled out in IPv6 case, but for IPv4 not.
So just zero them out by using plain memset (for this little amount of
bytes it's probably not worth the extra check for idiag_family == AF_INET).
Similarly, fix also other places where we fill that out.
Reported-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0e3da5bb8da45890b1dc413404e0f978ab71173e ]
ipgre_header_parse() needs to parse the tunnel's ip header and it
uses mac_header to locate the iphdr. This got broken when gre tunneling
was refactored as mac_header is no longer updated to point to iphdr.
Introduce skb_pop_mac_header() helper to do the mac_header assignment
and use it in ipgre_rcv() to fix msg_name parsing.
Bug introduced in commit c54419321455 (GRE: Refactor GRE tunneling code.)
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 37ab4fa7844a044dc21fde45e2a0fc2f3c3b6490 ]
This is similar to the set_peek_off patch where calling bind while the
socket is stuck in unix_dgram_recvmsg() will block and cause a hung task
spew after a while.
This is also the last place that did a straightforward mutex_lock(), so
there shouldn't be any more of these patches.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 12663bfc97c8b3fdb292428105dd92d563164050 ]
unix_dgram_recvmsg() will hold the readlock of the socket until recv
is complete.
In the same time, we may try to setsockopt(SO_PEEK_OFF) which will hang until
unix_dgram_recvmsg() will complete (which can take a while) without allowing
us to break out of it, triggering a hung task spew.
Instead, allow set_peek_off to fail, this way userspace will not hang.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d323e92cc3f4edd943610557c9ea1bb4bb5056e8 ]
maxattr in genl_family should be used to save the max attribute
type, but not the max command type. Drop monitor doesn't support
any attributes, so we should leave it as zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a3300ef4bbb1f1e33ff0400e1e6cf7733d988f4f ]
Brett Ciphery reported that new ipv6 addresses failed to get installed
because the addrconf generated dsts where counted against the dst gc
limit. We don't need to count those routes like we currently don't count
administratively added routes.
Because the max_addresses check enforces a limit on unbounded address
generation first in case someone plays with router advertisments, we
are still safe here.
Reported-by: Brett Ciphery <brett.ciphery@windriver.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 66e56cd46b93ef407c60adcac62cf33b06119d50 ]
Commit e40526cb20b5 introduced a cached dev pointer, that gets
hooked into register_prot_hook(), __unregister_prot_hook() to
update the device used for the send path.
We need to fix this up, as otherwise this will not work with
sockets created with protocol = 0, plus with sll_protocol = 0
passed via sockaddr_ll when doing the bind.
So instead, assign the pointer directly. The compiler can inline
these helper functions automagically.
While at it, also assume the cached dev fast-path as likely(),
and document this variant of socket creation as it seems it is
not widely used (seems not even the author of TX_RING was aware
of that in his reference example [1]). Tested with reproducer
from e40526cb20b5.
[1] http://wiki.ipxwarzone.com/index.php5?title=Linux_packet_mmap#Example
Fixes: e40526cb20b5 ("packet: fix use after free race in send path when dev is released")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Salam Noureddine <noureddine@aristanetworks.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 18fc25c94eadc52a42c025125af24657a93638c0 ]
After congestion update on a local connection, when rds_ib_xmit returns
less bytes than that are there in the message, rds_send_xmit calls
back rds_ib_xmit with an offset that causes BUG_ON(off & RDS_FRAG_SIZE)
to trigger.
For a 4Kb PAGE_SIZE rds_ib_xmit returns min(8240,4096)=4096 when actually
the message contains 8240 bytes. rds_send_xmit thinks there is more to send
and calls rds_ib_xmit again with a data offset "off" of 4096-48(rds header)
=4048 bytes thus hitting the BUG_ON(off & RDS_FRAG_SIZE) [RDS_FRAG_SIZE=4k].
The commit 6094628bfd94323fc1cea05ec2c6affd98c18f7f
"rds: prevent BUG_ON triggering on congestion map updates" introduced
this regression. That change was addressing the triggering of a different
BUG_ON in rds_send_xmit() on PowerPC architecture with 64Kbytes PAGE_SIZE:
BUG_ON(ret != 0 &&
conn->c_xmit_sg == rm->data.op_nents);
This was the sequence it was going through:
(rds_ib_xmit)
/* Do not send cong updates to IB loopback */
if (conn->c_loopback
&& rm->m_inc.i_hdr.h_flags & RDS_FLAG_CONG_BITMAP) {
rds_cong_map_updated(conn->c_fcong, ~(u64) 0);
return sizeof(struct rds_header) + RDS_CONG_MAP_BYTES;
}
rds_ib_xmit returns 8240
rds_send_xmit:
c_xmit_data_off = 0 + 8240 - 48 (rds header accounted only the first time)
= 8192
c_xmit_data_off < 65536 (sg->length), so calls rds_ib_xmit again
rds_ib_xmit returns 8240
rds_send_xmit:
c_xmit_data_off = 8192 + 8240 = 16432, calls rds_ib_xmit again
and so on (c_xmit_data_off 24672,32912,41152,49392,57632)
rds_ib_xmit returns 8240
On this iteration this sequence causes the BUG_ON in rds_send_xmit:
while (ret) {
tmp = min_t(int, ret, sg->length - conn->c_xmit_data_off);
[tmp = 65536 - 57632 = 7904]
conn->c_xmit_data_off += tmp;
[c_xmit_data_off = 57632 + 7904 = 65536]
ret -= tmp;
[ret = 8240 - 7904 = 336]
if (conn->c_xmit_data_off == sg->length) {
conn->c_xmit_data_off = 0;
sg++;
conn->c_xmit_sg++;
BUG_ON(ret != 0 &&
conn->c_xmit_sg == rm->data.op_nents);
[c_xmit_sg = 1, rm->data.op_nents = 1]
What the current fix does:
Since the congestion update over loopback is not actually transmitted
as a message, all that rds_ib_xmit needs to do is let the caller think
the full message has been transmitted and not return partial bytes.
It will return 8240 (RDS_CONG_MAP_BYTES+48) when PAGE_SIZE is 4Kb.
And 64Kb+48 when page size is 64Kb.
Reported-by: Josh Hunt <joshhunt00@gmail.com>
Tested-by: Honggang Li <honli@redhat.com>
Acked-by: Bang Nguyen <bang.nguyen@oracle.com>
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7150aede5dd241539686e17d9592f5ebd28a2cda ]
The behaviour of blackhole and prohibit routes has been corrected by setting
the input and output pointers of the dst variable appropriately. For
blackhole routes, they are set to dst_discard and to ip6_pkt_discard and
ip6_pkt_discard_out respectively for prohibit routes.
ipv6: ip6_pkt_prohibit(_out) should not depend on
CONFIG_IPV6_MULTIPLE_TABLES
We need ip6_pkt_prohibit(_out) available without
CONFIG_IPV6_MULTIPLE_TABLES
Signed-off-by: Kamala R <kamala@aristanetworks.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd935f44a40f8fb02aff2cc0df2269c92422df1c upstream.
Without a way to flush the osd client's notify workqueue, a watch
event that is unregistered could continue receiving callbacks
indefinitely.
Unregistering the event simply means no new notifies are added to the
queue, but there may still be events in the queue that will call the
watch callback for the event. If the queue is flushed after the event
is unregistered, the caller can be sure no more watch callbacks will
occur for the canceled watch.
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dbcae088fa660086bde6e10d63bb3c9264832d85 upstream.
create_singlethread_workqueue() returns NULL on error, and it doesn't
return ERR_PTRs.
I tweaked the error handling a little to be consistent with earlier in
the function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b72e19b9225d4297a18715b0998093d843d170fa upstream.
There are two places where we read "nr_maps" if both of them are set to
zero then we would hit a NULL dereference here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1874119664dafda3ef2ed9b51b4759a9540d4a1a upstream.
We've tried to fix the error paths in this function before, but there
is still a hidden goto in the ceph_decode_need() macro which goes to the
wrong place. We need to release the "req" and unlock a mutex before
returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 61c5d6bf7074ee32d014dcdf7698dc8c59eb712d upstream.
We can't use !req->r_sent to check if OSD request is sent for the
first time, this is because __cancel_request() zeros req->r_sent
when OSD map changes. Rather than adding a new variable to struct
ceph_osd_request to indicate if it's sent for the first time, We
can call the unsafe callback only when unsafe OSD reply is received.
If OSD's first reply is safe, just skip calling the unsafe callback.
The purpose of unsafe callback is adding unsafe request to a list,
so that fsync(2) can wait for the safe reply. fsync(2) doesn't need
to wait for a write(2) that hasn't returned yet. So it's OK to add
request to the unsafe list when the first OSD reply is received.
(ceph_sync_write() returns after receiving the first OSD reply)
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ccca4e37b1a912da3db68aee826557ea66145273 upstream.
check the "not truncated yet" case
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb845ff13a44477f8a411baedbf11d678b9daf0a upstream.
handle_reply() calls complete_request() only if the first OSD reply
has ONDISK flag.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96e4dac66f69d28af2b736e723364efbbdf9fdee upstream.
When an osd request is set to linger, the osd client holds onto the
request so it can be re-submitted following certain osd map changes.
The osd client holds a reference to the request until it is
unregistered. This is used by rbd for watch requests.
Currently, the reference is taken when the request is marked with
the linger flag. This means that if an error occurs after that
time but before the the request completes successfully, that
reference is leaked.
There's really no reason to take the reference until the request is
registered in the the osd client's list of lingering requests, and
that only happens when the lingering (watch) request completes
successfully.
So take that reference only when it gets registered following
succesful completion, and drop it (as before) when the request
gets unregistered. This avoids the reference problem on error
in rbd.
Rearrange ceph_osdc_unregister_linger_request() to avoid using
the request pointer after it may have been freed.
And hold an extra reference in kick_requests() while handling
a linger request that has not yet been registered, to ensure
it doesn't go away.
This resolves:
http://tracker.ceph.com/issues/3859
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd02cd2549cfcdfc57cb5ce57ffc3feb94f70575 upstream.
Evan Huus found (by fuzzing in wireshark) that the radiotap
iterator code can access beyond the length of the buffer if
the first bitmap claims an extension but then there's no
data at all. Fix this.
Reported-by: Evan Huus <eapache@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It turns out that commit: d3f7d56a7a4671d395e8af87071068a195257bf6 was
applied to the tree twice, which didn't hurt anything, but it's good to
fix this up.
Reported-by: Veaceslav Falico <veaceslav@falico.eu>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Shawn Landden <shawnlandden@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The upstream commit bb8140947a24 ("ip6tnl: allow to use rtnl ops on fb tunnel")
(backported into linux-3.10.y) left a bug which was fixed upstream by commit
1e9f3d6f1c40 ("ip6tnl: fix use after free of fb_tnl_dev").
The problem is a bit different in linux-3.10.y, because there is no x-netns
support (upstream commit 0bd8762824e7 ("ip6tnl: add x-netns support")).
When ip6_tunnel.ko is unloaded, FB device is deleted by rtnl_link_unregister()
and then we try to delete it again in ip6_tnl_destroy_tunnels().
This patch removes the second deletion.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 051a41fa4ee14f5c39668f0980973b9a195de560 upstream.
Multicast frames can't be transmitted as part of an aggregation
session (such a session couldn't even be set up) so don't try to
reorder them. Trying to do so would cause the reorder to stop
working correctly since multicast QoS frames (as transmitted by
the Aruba APs this was found with) would cause sequence number
confusion in the buffer.
Reported-by: Blaise Gassend <blaise@suitabletech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
